Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Signal detection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Advanced detectors and signal processing

Continued progress is reported toward development of a silicon on garnet technology which would allow fabrication of advanced detection and signal processing circuits on bubble memories. The first integrated detectors and propagation patterns have been designed and incorporated on a new mask set. In addition, annealing studies on spacer layers are performed. Based on those studies, a new double layer spacer is proposed which should reduce contamination of the silicon originating in the substrate. Finally, the magnetic sensitivity of uncontaminated detectors from the last lot of wafers is measured. The measured sensitivity is lower than anticipated but still higher than present magnetoresistive detectors.

Greve, D. W.↗
NASA NTRS1988

Flight test results of a vector-based failure detection and isolation algorithm for a redundant strapdown inertial measurement unit

Flight test results of a vector-based fault-tolerant algorithm for a redundant strapdown inertial measurement unit are presented. Because the inertial sensors provide flight-critical information for flight control and navigation, failure detection and isolation is developed in terms of a multi-level structure. Threshold compensation techniques for gyros and accelerometers, developed to enhance the sensitivity of the failure detection process to low-level failures, are presented. Four flight tests, conducted in a commercial transport type environment, were used to determine the ability of the failure detection and isolation algorithm to detect failure signals, such a hard-over, null, or bias shifts. The algorithm provided timely detection and correct isolation of flight control- and low-level failures. The flight tests of the vector-based algorithm demonstrated its capability to provide false alarm free dual fail-operational performance for the skewed array of inertial sensors.

Morrell, F. R.↗
NASA NTRS2011

Digital Interface Board to Control Phase and Amplitude of Four Channels

An increasing number of parts are designed with digital control interfaces, including phase shifters and variable attenuators. When designing an antenna array in which each antenna has independent amplitude and phase control, the number of digital control lines that must be set simultaneously can grow very large. Use of a parallel interface would require separate line drivers, more parts, and thus additional failure points. A convenient form of control where single-phase shifters or attenuators could be set or the whole set could be programmed with an update rate of 100 Hz is needed to solve this problem. A digital interface board with a field-programmable gate array (FPGA) can simultaneously control an essentially arbitrary number of digital control lines with a serial command interface requiring only three wires. A small set of short, high-level commands provides a simple programming interface for an external controller. Parity bits are used to validate the control commands. Output timing is controlled within the FPGA to allow for rapid update rates of the phase shifters and attenuators. This technology has been used to set and monitor eight 5-bit control signals via a serial UART (universal asynchronous receiver/transmitter) interface. The digital interface board controls the phase and amplitude of the signals for each element in the array. A host computer running Agilent VEE sends commands via serial UART connection to a Xilinx VirtexII FPGA. The commands are decoded, and either outputs are set or telemetry data is sent back to the host computer describing the status and the current phase and amplitude settings. This technology is an integral part of a closed-loop system in which the angle of arrival of an X-band uplink signal is detected and the appropriate phase shifts are applied to the Ka-band downlink signal to electronically steer the array back in the direction of the uplink signal. It will also be used in the non-beam-steering case to compensate for phase shift variations through power amplifiers. The digital interface board can be used to set four 5-bit phase shifters and four 5-bit attenuators and monitor their current settings. Additionally, it is useful outside of the closed-loop system for beamsteering alone. When the VEE program is started, it prompts the user to initialize variables (to zero) or skip initialization. After that, the program enters into a continuous loop waiting for the telemetry period to elapse or a button to be pushed. A telemetry request is sent when the telemetry period is elapsed (every five seconds). Pushing one of the set or reset buttons will send the appropriate command. When a command is sent, the interface status is returned, and the user will be notified by a pop-up window if any error has occurred. The program runs until the End Program button is depressed.

Smith, Amy E.↗
NASA NTRS2019

HD 2685 b: a hot Jupiter orbiting an early F-type star detected by TESS

We report on the confirmation of a transiting giant planet around the relatively hot (T(eff) = 6801 ± 76 K) star HD2685, whose transit signal was detected in Sector 1 data of NASA’s TESS mission. We confirmed the planetary nature of the transit signal using Doppler velocimetric measurements with CHIRON, CORALIE, and FEROS, as well as using photometric data obtained with the Chilean-Hungarian Automated Telescope and the Las Cumbres Observatory. From the joint analysis of photometry and radial velocities, we derived the following parameters for HD2685 b: P = 4.12688(+0.00005,-0.00004) days, e = 0.091(+0.039, -0.047), MP = 1.17 ± 0.12 M(J) , and R(P) =1.44 ± 0.05 R(J). This system is a typical example of an inflated transiting hot Jupiter in a low-eccentricity orbit. Based on the apparent visual magnitude (V = 9.6 mag) of the host star, this is one of the brightest known stars hosting a transiting hot Jupiter, and it is a good example of the upcoming systems that will be detected by TESS during the two-year primary mission. This is also an excellent target for future ground- and space-based atmospheric characterization as well as a good candidate for measuring the projected spin-orbit misalignment angle through the Rossiter–McLaughlin effect.

Matías I. Jones↗
DOE OSTI2023

Impact of environmental backgrounds on atmospheric monitoring of nuclear explosions

Radionuclide monitoring for nuclear explosions includes measuring radioactive aerosol and noble gas concentrations in the atmosphere. The International Monitoring System (IMS) of the Comprehensive Nuclear Test Ban Treaty (CTBT) has made such measurements for decades, revealing much about how atmospheric radioactivity impacts the sensitivity of the network. For example, civilian emissions of radioiodine make a substantial regional impact, but a minor global impact, while civilian radioxenon emissions create major regional and complex global impacts. This example statement is strongly influenced by the minimum signal level anticipated to be interesting. The original design of the IMS anticipated relatively large signal levels, and the accomplished IMS network substantially meets or exceeds the sensitivity needed to detect those signal levels. Much lower signal levels can be motivated, which could require reconsideration of station sensitivity. Using measured and simulated background concentrations, various possible desired signal levels, and an innovative anomaly threshold, maps of sensitivity and a station ranking are developed for current and future stations. These provide a strong motivation for additional experimentation to learn about sources and the potential plusses of new technology.

Eslinger, Paul W.↗
DOE OSTI2021

Neutron scattering study of the kagome metal Sc 3 Mn 3 Al 7 Si 5

Sc 3 Mn 3 Al 7 Si 5 is a rare example of a correlated metal in which the Mn moments form a kagome lattice. The absence of magnetic ordering to the lowest temperatures suggests that geometrical frustration of magnetic interactions may lead to strong magnetic fluctuations. We have performed inelastic neutron scattering measurements on Sc 3 Mn 3 Al 7 Si 5 , finding that phonon scattering dominates for energies from ~20–50 meV. These results are in good agreement with ab initio calculations of the phonon dispersions and densities of states, and as well reproduce the measured specific heat. A weak magnetic signal was detected at energies less than ~10 meV, present only at the lowest temperatures. The magnetic signal is broad and quasielastic, as expected for metallic paramagnets.

36 MATERIALS SCIENCE↗
NASA NTRS1990

A carrier sensed multiple access protocol for high data base rate ring networks

The results of the study of a simple but effective media access protocol for high data rate networks are presented. The protocol is based on the fact that at high data rates networks can contain multiple messages simultaneously over their span, and that in a ring, nodes used to detect the presence of a message arriving from the immediate upstream neighbor. When an incoming signal is detected, the node must either abort or truncate a message it is presently sending. Thus, the protocol with local carrier sensing and multiple access is designated CSMA/RN. The performance of CSMA/RN with TTattempt and truncate is studied using analytic and simulation models. Three performance factors, wait or access time, service time and response or end-to-end travel time are presented. The service time is basically a function of the network rate, it changes by a factor of 1 between no load and full load. Wait time, which is zero for no load, remains small for load factors up to 70 percent of full load. Response time, which adds travel time while on the network to wait and service time, is mainly a function of network length, especially for longer distance networks. Simulation results are shown for CSMA/RN where messages are removed at the destination. A wide range of local and metropolitan area network parameters including variations in message size, network length, and node count are studied. Finally, a scaling factor based upon the ratio of message to network length demonstrates that the results, and hence, the CSMA/RN protocol, are applicable to wide area networks.

Foudriat, E. C.↗
NASA NTRS1991

Diplex Fiber-Optic Link For Frequency And Time Signals

Diplex fiber-optic link part of Goldstone Deep Space Communications complex. Relatively inexpensive equipment delivers signals of high quality. At central station, signal combiner adds 5-MHz reference-frequency signal and 36-bit time-code signal, forming composite signal, which modulates light transmitted along optical fiber. At remote station, fiber-optic receiver detects composite signal and provides input to diplexer, which separates frequency reference signal from time-code signal. Signals then amplified to desired levels.

Lutes, George F.↗
DOE OSTI2024

Proximal Observations of Epicentral Infrasound Generated by Shallow Low-Magnitude Earthquakes in the Permian Basin, West Texas

Infrasound generated by earthquakes and explosions is generally detected at receivers at epicentral distances of hundreds to thousands of kilometers. However, proximal (<50 km) observations are especially important for low-magnitude earthquakes and low-yield explosions that may not generate signals capable of being detected at great ranges. Here, in this study, we present on the signals detected on an infrasound array 3 km away from two M L 2.9 earthquakes in the Permian Basin of west Texas. Local infrasound (LIS), generated at receivers during the passage of seismic waves, was detected following each earthquake. Epicentral infrasound (EIS), created at or near the epicenter and propagating away as a sound wave, was also detected. Array processing methods show that the EIS signals arrive from the same direction as the earthquake epicenters and at acoustic speeds. To our knowledge, these are the first observations of laterally propagating EIS at proximal ranges following an earthquake of any magnitude.

58 GEOSCIENCES↗
DOE OSTI2022

Detecting CAN Masquerade Attacks with Signal Clustering Similarity

Vehicular Controller Area Networks (CANs) are susceptible to cyber attacks of different levels of sophistication. Fabrication attacks are the easiest to administer—an adversary simply sends (extra) frames on a CAN—but also the easiest to detect because they disrupt frame frequency. To overcome time-based detection methods, adversaries must administer masquerade attacks by sending frames in lieu of (and therefore at the expected time of) benign frames but with malicious payloads. Research efforts have proven that CAN attacks, and masquerade attacks in particular, can affect vehicle functionality. Examples include causing unintended acceleration, deactivation of vehicle’s brakes, as well as steering the vehicle. We hypothesize that masquerade attacks modify the nuanced correlations of CAN signal time series and how they cluster together. Therefore, changes in cluster assignments should indicate anomalous behavior. We confirm this hypothesis by leveraging our previously developed capability for reverse engineering CAN signals (i.e., CAN-D [Controller Area Network Decoder]) and focus on advancing the state of the art for detecting masquerade attacks by analyzing time series extracted from raw CAN frames. Specifically, we demonstrate that masquerade attacks can be detected by computing time series clustering similarity using hierarchical clustering on the vehicle’s CAN signals (time series) and comparing the clustering similarity across CAN captures with and without attacks. We test our approach in a previously collected CAN dataset with masquerade attacks (i.e., the ROAD dataset) and develop a forensic tool as a proof of concept to demonstrate the potential of the proposed approach for detecting CAN masquerade attacks.

Moriano Salazar, Pablo↗
NASA NTRS2006

Progress in testing exo-planet signal extraction on the TPF-I Planet Detection Testbed

The TPF Interferometer (TPF-I) concept is being studied at the Jet Propulsion Laboratory and the TPF-I Planet Detection Testbed has been developed to simulate the detection process for an earthlike planet orbiting a star within about 15 pc. The testbed combines four beams of infrared light simulating the operation of a dual chopped Bracewell interferometer observing a star and a faint planet. This paper describes the results obtained this year including nulling of the starlight on four input beams at contrast ratios up to 250,000 to 1, and detection of faint planet signals at contrast ratios with the star of 2 million to 1.

nulling↗
DOE OSTI2021

Detection, monitoring, and determination of location of changes in metallic structures using multimode acoustic signals

Acoustic transducers generate and receive acoustic signals at multiple locations along a surface of rigid structure, wherein longitudinal spacing between transducer locations define measurement zones. Acoustic signals with chosen amplitude-time-frequency characteristics excite multiple vibration modes in the structure within each zone. Small mechanical changes in inspection zones lead to scattering and attenuation of broadband acoustic signals, which are detectable as changes in received signal characteristics as part of a through-transmission technique. Additional use of short, narrowband pulse acoustic signals as part of a pulse-echo technique allows determination of the relative location of the mechanical change within each zone based on the differential delay profiles. For accurate acoustic modeling and simulation, the mesh size, time step, time delay, and time-window size are optimized. Frequency normalization of the Short-Time Fourier Transform of acoustic response output improves experiment-simulation cross-validation. Applications of the method to structures with arbitrarily complex geometries are also demonstrated.

Findikoglu, Alp Tugrul↗
NASA NTRS1989

Design And Analysis Of Optical Communication Links

To convey to prospective designers intuitive understanding based on unique characteristics of optical communication systems, report presents method of design and analysis of outer-space optical communication link using pulse-position modulation (PPM) and in which received signal sufficiently weak to require detection by photomultiplier operating in photon-counting mode. Step 1 requires some knowledge or assumptions about parameters of transmitter and receiver. Step 2 determination of average number of background-noise photons detected during PPM timeslot. Step 3 average number, Ps of signal photons detected per signal pulse compared with average number, Pn of noise pulses detected per PPM timeslot.

Lesh, J. R.↗
DOE OSTI2025

Study of the connected four-point correlation function of galaxies from the DESI Data Release 1 luminous red galaxy sample

We present a measurement of the non-Gaussian four-point correlation function (4PCF) from the DESI DR1 luminous red galaxy (LRG) sample. For the gravitationally induced parity-even 4PCF, we detect a signal with a significance of 14.7⁢𝜎 using our fiducial setup. We assess the robustness of this detection through a series of validation tests, including auto and cross-correlation analyses, sky partitioning across multiple patch combinations, and variations in radial scale cuts. Due to the low completeness of the sample, we find that differences in fiber assignment implementation schemes can significantly impact estimation of the covariance and introduce biases in the data vector. After correcting for these effects, all tests yield consistent results. This is one of the first measurements of the connected 4PCF on the DESI LRG sample; the good agreement between the simulation and the data implies that the amplitude of the density fluctuation inferred from the connected 4PCF is consistent with the Planck Λ⁢ CDM cosmology. The methodology and diagnostic framework established in this work provide a foundation for interpreting parity-odd 4PCF.

Cosmology↗
NASA NTRS1993

Signal processing aspects of windshear detection

Low-altitude windshear (LAWS) has been identified as a major hazard to aircraft, particularly during takeoff and landing. The Federal Aviation Administration (FAA) has been involved with developing technology to detect LAWS. A key element in this technology is high resolution pulse Doppler weather radar equipped with signal and data processing to provide timely information about possible hazardous conditions.

Aalfs, David D.↗
DOE OSTI2020

Search for multimessenger signals in NOvA coincident with LIGO/Virgo detections

Using the NOvA neutrino detectors, a broad search has been performed for any signal coincident with 28 gravitational wave events detected by the LIGO/Virgo Collaboration between September 2015 and July 2019. For all of these events, NOvA is sensitive to possible arrival of neutrinos and cosmic rays of GeV and higher energies. For five (seven) events in the NOvA Far (Near) Detector, timely public alerts from the LIGO/Virgo Collaboration allowed recording of MeV-scale events. No signal candidates were found.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗