Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Effect of Quenching Process on Microstructures and Mechanical Properties of Fe-0.9Mn-0.5Cr-2.4Ni-0.5Mo-C Steel

To develop an appropriate quenching process to produce Fe-0.9Mn-0.5Cr-2.4Ni-0.5Mo-C steel, the microstructures and mechanical properties of this steel were investigated under the direct quenching and tempering (DQT) and the direct quenching, reheated quenching and tempering (DQQT) heat treatment processes. The microstructure of the DQQT specimen was basically tempered sorbite with spherical precipitates, while quite a bit of tempered martensite was in the DQT specimen with dispersive nanoscaled precipitates. The yield strengths of the DQT and DQQT specimens were 1154 and 955 MPa, respectively. The yield strength of the DQT specimen was higher than that of the DQQT specimen because of its finer grain size, higher density of dislocations and dispersed precipitates. The DQQT specimen had spherical precipitates, which hindered the propagation of the crack. Moreover, the high-angle grain boundaries in the DQQT specimen took a higher proportion. Therefore, the Charpy impact values of DQT and DQQT specimens at − 60 °C were 38 and 75 J, respectively. Consequently, the mechanical properties of the Fe-0.9Mn-0.5Cr-2.4Ni-0.5Mo-C steel, which met the standard of 1000 MPa grade steel plate for hydropower station, were acquired by the DQQT process.

36 MATERIALS SCIENCE↗

Preparation and Characterization of Silanes Films to Protect Electrogalvanized Steel

Silanes are an interesting alternative to chromate-based surface treatments for temporary protection of electrogalvanized steel. In this work, the protective behavior of 3-mercaptopropyltrimethoxysilane (MTMO), 3-aminopropyltriethoxysilane (AMEO), or 3-glycidoxypropyltrimethoxysilane (GLYMO) films applied on electrogalvanized automotive quality steel sheets has been studied. The silane coating morphology, composition, and porosity were characterized by scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDS), x-ray fluorescence, immersion in copper sulfate, and cyclic voltammetry. The corrosion protection was evaluated by polarization curves, electrochemical noise measurements, electrochemical impedance spectrometry, and accelerated humidity chamber tests. The results showed that the silanes protect temporarily electrogalvanized steel from corrosion. MTMO forms a relatively thick and cracked film. AMEO and GLYMO films were so thin that they could not be observed by SEM but silicon was detected by EDS. MTMO provided good temporary protection, being an alternative to replace Cr(VI) as protector of electrogalvanized steel.

36 MATERIALS SCIENCE↗

Improving Corrosion Resistance of 316L Austenitic Stainless Steel Using ZrO{sub 2} Sol-Gel Coating in Nitric Acid Solution

In this study, thin-film coating of zirconium oxide (ZrO{sub 2}) was prepared by sol-gel method and subsequent heat treatment process. The sol was prepared by controlled hydrolysis of zirconium tetrapropoxide using acetic acid and ethanol/acetylacetone mixture as catalyst and chelating agent, respectively, and finally deposited onto the 316L austenitic stainless steel (316L SS) using dip coating method in order to improve its corrosion resistance in nitric acid medium. The composition, structure, and morphology of the coated surface were investigated by x-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The obtained results from XRD and FTIR state the formation of tetragonal and monoclinic ZrO{sub 2} phase. Also, the obtained results from surface morphology investigation by SEM and AFM indicate the formation of smooth, homogeneous and uniform coatings on the steel substrate. Then, the corrosion behavior of stainless steel was investigated in a 1 and 10 M nitric acid solutions using electrochemical impedance spectroscopy and linear polarization test. The obtained results from these tests for ZrO{sub 2}-coated specimens indicated a considerable improvement in the corrosion resistance of 316L stainless steel by an increase in corrosion potential and transpassive potential, and a decrease in passive current density and corrosion current density. The decrease in passive current density in both the concentration of solutions was two orders of magnitude from bare to coated specimens.

36 MATERIALS SCIENCE↗

Effect of Bainitic Microstructure on Ballistic Performance of Armour Steel Weld Metal Using Developed High Ni-Coated Electrode

Welding of armour steel has gained significant importance during the past few years as recent civilian and military requirements demand weld metal properties matching with base metal having good ballistic performance along with high strength and toughness at − 40 °C as per specification. The challenge of armour steel welding therefore lies in controlling the weld metal composition which is strongly dependent on welding electrode/consumables, resulting in desired weld microstructure consisting of lower bainite along with retained austenite. The performance of butt-welded armour steel joints produced by the developed electrodes was evaluated using tensile testing, ballistic testing, impact toughness at room temperature and subzero temperature. Microstructures of weld metals are exclusively characterized by x-ray diffraction technique, scanning electron microscope and transmission electron microscopy with selected area diffraction pattern. Experimental results show that weld metal with relatively lower carbon, higher manganese and lower nickel content was attributed to lower bainite with film type of retained austenite may be considered as a most covetable microstructure for armour steel weld metal.

36 MATERIALS SCIENCE↗

Effect of the Combined Addition of Y and Ti on the Second Phase and Mechanical Properties of China Low-Activation Martensitic Steel

In this study, approximately 0.35% Ti and two different Y contents were added to China low-activation martensitic (CLAM) steel during melting in a vacuum induction melting furnace. Scanning electron microscopy, transmission electron microscopy, x-ray diffraction, tensile tests, and Charpy impact tests were used to investigate the effects of the combined addition of Y and Ti on the second phase and mechanical properties. The results indicated that Y and Fe formed the large intermetallic compound Fe-Y; the compound easily aggregated in the grain boundaries and exhibited the strength of CLAM steel. Ti did not combine with Y to form the Y-Ti-O phase; however, it could combine with Ta and W to form MC precipitates, which were generally in the 20-50 nm size range. The CLAM steel with a higher Y content exhibited lower yield and tensile strengths at room temperature, with both steels yielding almost identical strengths at 600 °C.

36 MATERIALS SCIENCE↗

A Micro-Mechanism-Based Continuum Corrosion Fatigue Damage Model for Steels

A micro-mechanism-based corrosion fatigue damage model is developed for studying the high-cycle corrosion fatigue of steel from multi-scale viewpoint. The developed physical corrosion fatigue damage model establishes micro-macro relationships between macroscopic continuum damage evolution and collective evolution behavior of microscopic pits and cracks, which can be used to describe the multi-scale corrosion fatigue process of steel. As a case study, the model is used to predict continuum damage evolution and number density of the corrosion pit and short crack of steel component in 5% NaCl water under constant stress amplitude at 20 kHz, and the numerical results are compared with experimental results. It shows that the model is effective and can be used to evaluate the continuum macroscopic corrosion fatigue damage and study microscopic corrosion fatigue mechanisms of steel.

36 MATERIALS SCIENCE↗

A Study on the Corrosion Behavior of Carbon Steel Exposed to a H{sub 2}S-Containing NH{sub 4}Cl Medium

NH{sub 4}Cl corrosion failure often occurs in the overhead systems of hydrotreaters, and this failure is always accompanied by the appearance of H{sub 2}S. A combination of electrochemical and surface spectroscopic (SEM/EDS, AFM, XRD) techniques was used to investigate the effect of different factors, including the surface roughness, temperature, dissolved oxygen, pH and H{sub 2}S concentration, on the corrosion behavior of carbon steel in an NH{sub 4}Cl environment with the presence of H{sub 2}S. The effect of H{sub 2}S concentrations (at the ppm level) on the corrosion behavior of carbon steel was systematically revealed. The experimental results clearly indicated that the corrosion rate reached a minimum value at 10 ppm H{sub 2}S. The steel surface was covered by a uniform corrosion product film in a 10 ppm H{sub 2}S environment, and the corrosion product film was tight and protective. The ammonia from NH{sub 4}Cl helped maintaining the protectiveness of the corrosion films in this environment. Dissolved oxygen mainly accelerated the cathodic reaction. The cathodic limiting current density increased with increasing temperature, and the anodic branch polarization curves were similar at different temperatures. The anodic current density decreased as the pH decreased, and the cathodic current density increased as the pH decreased. The absolute surface roughness (R{sub a}) of carbon steel increased from 132.856 nm at 72 h to 153.973 nm at 144 h, and the rougher surface resulted in a higher corrosion rate. The critical innovation in this research was that multiple influential factors were revealed in the NH{sub 4}Cl environment with the presence of H{sub 2}S.

36 MATERIALS SCIENCE↗

Influence of Boron on Austenite to Ferrite Transformation Behavior of Low Carbon Steel Under Continuous Cooling

In the current work, the influence of boron on austenite to ferrite transformation behavior under continuous cooling condition and its associated features, e.g., final microstructure, mechanical properties, etc., in low carbon steel has been studied. The steels (C 0.04 wt.%, B 10-100 ppm) prepared in an open air laboratory furnace showed identical microstructures having ferrite grains of 20-25 µm. However, tensile test data indicate variation of yield strength and ultimate tensile strength with boron content. The yield point elongation and strain aging index both were found to decrease with increase in boron content or boron-to-nitrogen ratio. As the boron nitride precipitates stimulate the nucleation of ferrite phase, the dilation curves show an increase in austenite to ferrite transformation start temperature with boron content. The resulting microstructure and hardness value also corroborate the finding. Transmission electron microscopy findings revealed the presence of ultra-fine boron nitride (BN) precipitates in both grain boundary and grain body of the steel having boron concentration of 30 ppm and beyond. The presence of these precipitates also increased with boron content. Based on austenite decomposition behavior, related microstructure and hardness values it is conjectured that these BN precipitates may act as nucleating agent for polygonal ferrite during austenite decomposition, thereby softening the steel during fast cooling.

36 MATERIALS SCIENCE↗

Finite Element Simulation and Optimization of Gas-Quenching Process for Tool Steels

Various gas-quenching processes, including marquenching, were investigated to optimize gas-quenching processes in terms of distortion and hardness by means of numerical and experimental analyses. The temperature, microstructure, hardness, and distortion during the various gas-quenching processes of a tool steel block were simulated using a finite element method based on a coupled thermo-metallurgical–mechanical model. The predicted temperature, hardness, and distortion agreed well with the experimental data. The tool steel block (200 × 150 × 70 mm{sup 3}) quenched under 10 bar pressure of nitrogen gas (Case 2) had higher hardness due to the higher martensite fraction and larger distortion owing to the higher thermal stress induced by faster cooling, compared to the block quenched under 2 bar pressure of nitrogen gas (Case 1). The tool steel block marquenched under 10 bar pressure of nitrogen gas interrupted by isothermal holding at 500 °C (Case 3) had 30% smaller distortion with a negligible loss of hardness compared to Case 2. Furthermore, the simulation results could provide an optimized process condition to minimize distortion of the gas-quenched tool steel block while satisfying the hardness requirement.

36 MATERIALS SCIENCE↗

Dynamic Recrystallization and Grain Refinement of Fe-P-C-Si and Fe-P-C-Si-N Steels

Grain refinement is an effective technique to improve the mechanical properties of steels. In the present work, single-pass hot compression experiments have been conducted on two different compositions of high phosphorous steels to study the microstructural evolution and ferrite grain refinement at various strain rates and deformation temperatures, i.e., 0.01-10 s{sup −1} and 750-1050 °C, respectively. Optical metallography has been employed to understand the physical processes that take place during hot deformation process. The results indicate that when these compositions of high phosphorous steels are worked at relatively low temperatures in the intercritical regions, a ferrite grain size of 5-7 µm is obtained. It is observed that the grain size decreases with an increase in strain rate and with the decrease in deformation temperature. Based on the values of stress exponent (n) obtained in the present work, dislocation creep is identified as the deformation mechanism. The activation energies for deformation of these two types of high phosphorous steels have been calculated. The effect of the alloying elements on the stress–strain curve, microstructure, and grain refinement has been discussed.

36 MATERIALS SCIENCE↗

Effect of Deep Cryogenic Treatment on Mechanical Properties and Microstructure of the Tool Steel CR7V for Hot Stamping

To solve the failure problem of hot stamping tool, the CR7V steel was deep cryogenically treated at different dwelling times with multiple tempering. The hardness, impact toughness and wear resistance of the CR7V steel were examined, and the effects of deep cryogenic treatment on the microstructure of the CR7V steel were studied by means of optical microscope, scanning electron microscope and energy-dispersive spectroscopy. The results show that deep cryogenic treatment has little effect on the hardness of the tempered CR7V steel, but improves its impact toughness and wear resistance. The improvement in mechanical properties is a result of the combination of dissolution of large carbide particles, formation of small-sized and uniformly distributed carbide particles and fine tempered martensite structure. The cryogenic treatment is optimized as follows: vacuum gas quenching, deep cryogenic treatment at − 196 °C for 6 h and triple tempering at 560 °C for 2 h, which improves the wear resistance by 68% and the impact toughness by 58% compared to the conventional heat treatment.

36 MATERIALS SCIENCE↗

Effect of Welding Parameters on the Corrosion Behavior of Dissimilar Alloy Welds of T6 AA6061 Al-Galvanized Mild Steel

Partial replacement of steel by Aluminium (Al) alloys is a promising approach adopted by automotive sector to improve fuel efficiency without compromising on the strength. However, this results in the generation of dissimilar welds of Al alloys and steel. Understanding the corrosion behavior of Al alloys–steel welds as a function of welding parameters is critical in the successful application of such alloys. The present study reports the intergranular corrosion behavior of T6 heat-treated AA6061 Al alloy-galvanized mild steel lap joints, welded by metal inert gas welding–brazing technique as a function of different welding parameters, viz. weld speed (4-6 m/min) and wire feed rate (0.8-0.9 m/min), following ASTM G 67-04. Weld characterization was performed by field emission scanning electron microscopy (FESEM), x-ray diffraction and nano-hardness measurement. Results indicate heavy dissolution and metal loss at the interface. A high volume fraction of Al-Fe intermetallics was precipitated at the weld interfaces, resulting in high hardness and higher localized corrosion. The thickness of Al-Fe intermetallic layer increased with increasing wire feed rate and lower weld speed which enhanced the severity of galvanic and intergranular corrosion.

36 MATERIALS SCIENCE↗

Corrosion Resistances of Steel Pipe Coated with Two Types of Enamel by Two Coating Processes

The corrosion behaviors of uncoated, enamel-coated, and epoxy-coated steel samples were evaluated in 3.5 wt.% NaCl solution with open-circuit potential, electrochemical impedance spectroscopy and potentiodynamic polarization tests. Two types of enamel (powder and slurry) were coated on steel samples in electrostatic and wet spraying processes, respectively. Twelve 25 mm × 25 mm steel samples were cut from an API 5L X65 pipe of 323.850 mm in outer diameter and 9.525 mm in wall thickness. They were divided into four groups of three identical samples. Each group represents one of the four conditions: uncoated, powder enamel-coated, slurry enamel-coated and epoxy-coated. Scanning electron microscopy images revealed that the powder and slurry enamel coatings were approximately 180 and 235 µm thick, respectively. The powder enamel coating has fewer but larger isolated pores than the slurry enamel coating. Electrochemical tests consistently indicated that the powder and slurry enamel coatings provided slightly better and worse corrosion protection to the coated steel samples, respectively, than the epoxy coating. The charge transfer resistances of all the coated samples are approximately 10{sup 8} times larger than that of the uncoated samples. All the coated samples were unlikely corroded within 2 h of immersion.

36 MATERIALS SCIENCE↗

Achieving Excellent Strength–Ductility and Impact Toughness Combination by Cyclic Quenching in Medium Mn TRIP-Aided Steel

A novel heat treatment process combined cyclic quenching (CQ) with austenite reversion treatment (ART) is proposed to obtain high strength–ductility and high-impact toughness combination in Fe-0.18C-8.92Mn-3.43Al (in mass%) steel. The process referred as CQ-ART was designed for accomplishing the following objectives: (i) refine the prior austenite grains during cyclic quenching process, (ii) further obtain the refined austenite–ferrite block and (iii) improve the stabilities of retained austenite with Mn/C enrichment during ART process. The outstanding product of tensile strength and total elongation of CQ-ART-treated steels was 41.53 and 37.39 GPa%, respectively, and higher than the ART steel of 27.45 GPa%. The highest Charpy impact toughness of CQ-ART steel can reach to 221 J, which is mainly attributed to the refined grains and discontinuous transformation-induced plasticity (TRIP) effect.

36 MATERIALS SCIENCE↗

On the Hot Deformation Behavior of a Ni-Free Austenitic Stainless Steel Interstitially Alloyed with Low Nitrogen Content

Hot deformation behavior of a Ni-free, Fe-17Cr-12Mn-0.28N-0.06C (wt.%) austenitic stainless steel, hereinafter coded as FeCrMnN, was investigated using hot compression tests conducted under different deformation conditions comprising temperature and strain rate ranges of 800-1200 °C and 0.01-10 s{sup −1}, respectively. While the hot deformation at high strain rate and low temperatures (e.g., 10 s{sup −1} and 800 or 900 °C) showed essentially dynamic recovery, resulting in a pancake-shaped microstructure, most of the other conditions exhibited occurrence of dynamic recrystallization (DRX). Increasing deformation temperature and decreasing strain rate showed a decrease in the critical stress and strain for initiating DRX. In general, DRX resulted in extensive microstructural reconstitution and grain refinement. For instance, hot deformation at 1000 °C/0.01 s{sup −1} resulted in a fully recrystallized fine-grained microstructure with an average grain size of about 15 μm in comparison with the initial grain size of 60 µm. Increasing the temperature enhanced grain growth, but an increase in strain rate resulted in a finer grain structure. The amount of delta ferrite in the present steel varied under different conditions of deformation such that the lowest amount of delta ferrite (about 4.5%) was observed at 1000 °C. The activation energy of deformation (Q{sub def}) for the present FeCrMnN steel with the initial grain size of 60 µm was estimated to be about 502 kJ/mol, which is higher than that of the conventional austenitic stainless steels.

36 MATERIALS SCIENCE↗

Correlation Between Structure and Properties of Low-Carbon Cu-Ni-Mo-Ti-Nb Ultrahigh-Strength Steel

Low-carbon Cu-Ni-Mo-Ti-Nb steel having more than 1700 MPa tensile strength and good low-temperature impact toughness was successfully designed and processed for automobile, defence and structural applications. The steel was thermomechanical controlled processed at a different finish rolling temperatures (750-850 °C) and cooled at two different conditions: air cooling and water quenching. Evolutions of microstructure and precipitates were thoroughly characterised to understand the effect of different factors, such as steel composition, finish rolling temperature and cooling rate on the mechanical properties. The results indicate that the steel processed at 750 °C finish rolling temperature (FRT) followed by water quenching has exhibited superior tensile properties with a yield strength of 1034-1449 MPa, the tensile strength of 1598-1726 MPa and total elongation of 10-13%. Such an ultrahigh-strength level is primarily attributed to the combined effect of lower bainite dominated microstructure along with precipitation hardening. The satisfactory low-temperature toughness is promoted by low finish rolling temperature and higher amount of misorientation offered by the boundaries within the lower bainite.

36 MATERIALS SCIENCE↗

Feasibility of Using Steel Drums for the Confinement of Burned Low-Level Radioactive Waste Ashes

The selection of suitable materials to construct a facility for the final disposal of radioactive wastes (repository) is a challenge in materials science, since these facilities must be designed to provide confinement to the radionuclides for long periods of time. In the case of the low-level radioactive waste (LLRW) repository, the confinement of the species must be guaranteed for more than 300 years. In this context, the evaluation of the proposed materials must be performed under accelerated laboratory tests. One type of LLRW consists of ashes that result from the incineration of solid combustible radioactive waste. In Argentina, one of the proposed projects is to place these ashes inside steel drums and immobilized them by a cementation process. The issue to be resolved is whether the steel drums will undergo internal corrosion depending on the presence of certain deleterious species. The aim of the present work is to evaluate the corrosion susceptibility of steel drums containing simulated cemented incineration ashes. To this purpose, a special type of specimen was designed and the corrosion process was followed up for almost 4 years. It was found that, although the deleterious effect of chloride is undeniable, corrosion rates are not as high as to compromise the integrity of the steel drums for a design period of 300 years.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Microstructure Evolution and Stress Corrosion Cracking Susceptibility of 12Cr Martensitic Steel Upon Long-Term Service in Power Plants

After 230,000-h long-term service at 550 °C/13.7 MPa, the microstructure of a kind of 12Cr martensitic steel was investigated using scanning electron microscopy, backscattering electron microscope and x-ray diffraction analysis. The results show that the precipitation and coarsening of carbides at grain/lath boundaries are the main cause of microstructure degradation. The static immersion tests and the slow strain rate test coupled with electrochemical impedance spectroscopy were conducted on the served steel in 1.0% NaCl solution, and it turns out that the pitting corrosion resistance and repassivation ability of the steel are significantly reduced as a result of microstructure degradation. The stress corrosion cracking susceptibility of the steel was also studied. Fracture morphology analysis shows that the secondary crack in conjunction with slip lines is a result of the coalescence of micro-cracks nucleated from the pits.

36 MATERIALS SCIENCE↗