Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Spin resistance evaluation of a light airplane

A brief history of stall/spin technology for light general aviation airplanes and proposed criteria to describe desirable characteristics of a spin-resistant airplane are presented. Flight tests of a representative light airplane to evaluate compliance with and usefulness of the criteria are presented. The baseline airplane configuration would not meet the spin resistance criteria. Tests of the airplane with a wing leading edge modification to enhance its spin resistance showed compliance with the proposed criteria.

Stough, H. Paul, III↗
NASA NTRS1987

Evaluation of airplane spin resistance using proposed criteria for light general aviation airplanes

Proposed criteria to describe desirable characteristics of a spin-resistant airplane are reviewed. Flight tests of two representative light airplanes to evaluate compliance with the criteria are also presented. The baseline airplane configurations would not meet the spin resistance criteria. Tests of the airplanes with a wing leading edge modification to enhance spin resistance showed compliance with the proposed criteria. The tests demonstrated the usefulness of the criteria when the criteria are applied in the manner described.

Stough, H. Paul, III↗
NASA NTRS1987

Consequences of bacterial resistance to disinfection by iodine in potable water

This study was done to quantify the sensitivity of bacteria to iodine under controlled laboratory conditions. When exposed to 1 mg/1 I2 for 1 min, bacteria isolated from the Shuttle were more resistant than a P. aeruginosa isolated from a povidine-iodine solution. Cultures grown in rich media were more sensitive than those grown in low nutrient solutions. The P. aeruginosa and a P. cepacia isolated from the Shuttle were resuspended in PBW after exposure to iodine. Iodinated cells recovered better than uniodinated controls. Pseudomonads in biofilms developed on coupons of stainless steel were more resistant to iodine than cells suspended in buffered water. Although resistant bacteria may colonize spacecraft water systems, multiple treatment barriers should provide adequate control of these contaminants.

Mcfeters, Gordon A.↗
NASA NTRS1988

Rugged low-resistance contacts to YBa2Cu3O(x)

Rugged low-resistance contacts to a high-T(c) superconductor YBa2Cu3O(x) were made by melting gold onto the sample surface, where it diffused into the sample pores making a strong mechanical contact in the form of a bead. Contact resistances lower than 50 microohm were obtained, allowing passage, without heating, of a direct current of about 5 A while the sample remained in the superconducting state at 20 K. Results of SEM and of contact-resistance, critical-current, and shear-strength measurements on these contacts are included.

Caton, R.↗
NASA NTRS1988

Application of the V(R) resistance curve method to fracture of various crack configurations

The fracture resistance curve method of Newman (1985), based on the crack-tip-opening displacement, V(R), for a 'stationary' crack, was applied to various crack configurations in 2024-T351 and 7075-T651 aluminum alloys tested at room temperature. Using a stationary crack solution, the crack-tip-displacement was calculated at the current crack length for the crack configurations which included compact, middle-crack, single-edge-crack, and three-hole-crack tension specimens. The results showed that the V(R) resistance curves are insensitive to crack length, specimen width, and specimen type up to maximum load. After the maximum load is reached, the V(R) remains nearly constant; this constant depends only on specimen type, specimen width, and crack length. The V(R) resistance curve method can be used with the strip-yield analyses to accurately predict stable crack growth and instability of cracked metallic materials.

Newman, J. C., Jr.↗
NASA NTRS1988

Extremely low resistance nonalloyed ohmic contacts on GaAs using InAs/InGaAs and InAs/GaAs strained-layer superlattices

Employing a structure consisting of n(+)-InAs/InGaAs and InAs/GaAs strained-layer superlattices (SLSs) grown by molecular beam epitaxy on GaAs films, nonalloyed contact resistances less than 8.5 x 10 to the -8th ohm sq cm have been obtained. Self-consistent simulations show that these extremely small nonalloyed contact resistances are due to the suppression of the depletion depth in the GaAs channel and tunneling through the SLS layer. Similar structures on InGaAs channels have led to nonalloyed specific contact resistances of about 1.5 x 10 to the -8th ohm sq cm. These results represent the smallest figures reported for these important material systems.

Peng, C. K.↗
NASA NTRS1989

A global climatology of albedo, roughness length and stomatal resistance for atmospheric general circulation models as represented by the Simple Biosphere Model (SiB)

Components of the Simple Biosphere Model (SiB) of Sellers et al. (1986) were used to generate global monthly fields of surface albedo (0.4-4.0 microns), roughness length and minimum surface (stomatal) resistance. SiB consists of three submodels which describe the roles of radiative transfer, turbulent transfer and surface resistance in determining the energy balance of the vegetated land surface. These three submodels were detached from SiB and used on the SiB parameter set (total and green leaf area index, leaf angle orientation, canopy dimensions, etc.) to calculate global monthly fields of albedo, roughness length and minimum stomatal resistance at 1 x 1 deg resolution. Time series of various parameters are also displayed for each vegetation type for specified grid points. The SiB results compare reasonably well with appropriate measurements obtained from the literature and have the additional merit of being mutually consistent; the three submodels use many common parameters, which ensures that, for each grid area, the calculated surface properties are closely interrelated as is the case in nature. The derived fields provide a check on the operation of the submodels and the correctness of the parameter set. They can also be used as prescribed fields for GCMs that do not have biophysically based land surface parameterizations.

Dorman, J. L.↗
NASA NTRS1990

Calculating The Resistivity Of A Deposited Film

Iterative procedure computes resistivity from measurements by four-probe method. Computer program and technique developed to aid in solution of class of problems in which measurements of electrical resistivity needed for substance deposited on substrate of higher resistivity than deposited layer.

Oberle, Lawrence G.↗
NASA NTRS1989

Investigations of modifications to improve the spin resistance of a high-wing, single-engine, light airplane

A general aviation aircraft with drooped leading edge modifications for improvement of lateral stability at high angles of attack has been flight tested in combination with a ventral fin which improves directional stability. The two modifications were assessed in light of spin-resistance criteria proposed for incorporation into FAA certification regulations. The configuration combining outboard wing leading-edge droop and a ventral fin yielded a substantial increase in spin resistance, but fell short of all requirements encompassed by the proposed spin-resistance criteria.

Manuel, G. S.↗
NASA NTRS1990

New resistivity for high-mobility quantum Hall conductors

Measurements showing dramatic nonlocal behavior in the four-terminal resistances of a high-mobility quantum Hall conductor are presented. These measurements illustrate that the standard definition of the resistivity tensor is inappropriate, but they are in excellent agreement with a new model of the conductor that treats the edge and bulk conducting pathways independently. This model uses a single intensive parameter, analogous to a local resistivity for the bulk channel only, to characterize the system.

Mceuen, P. L.↗
NASA NTRS1989

The effect of length and diameter on the resistivity of bromine intercalated graphite fibers

The resistivity of bromine intercalated graphite fibers has been shown to vary with both the diameter and the length of the fibers. This is due to bromine depletion from the fiber surface. Model calculations assuming a 1.0 micron bromine depletion zone for P-100, and 3.0 microns for vapor-grown graphite fibers fit the respective diameter dependence of their resistivities quite well. Length dependence data imply a bromine depletion zone along the length of P-100 fibers which is also a few microns, but that of vapor grown fibers appears to be as large as 300 microns. Despite these values, microfilaments, which are much smaller than the expected depletion zones, do form residual bromine intercalation compounds with resistivities about one-half of their pristine value.

Gaier, James R.↗
NASA NTRS1991

Carotid baroreceptor influence on forearm vascular resistance during low level lower body negative pressure

The degree of forearm vasoconstriction induced by low levels of lower body negative pressure (LBNP) provides a measure of the responsiveness of the cardiopulmonary baroreflex. The validity of this measurement is based on the assumption that this vasoconstriction response is not influenced by unloading of carotid baroreceptors. To test the hypothesis that arterial baroreceptor unloading does not alter the degree of forearm vascular resistance during low levels of LBNP, 12 subjects were exposed to -15 and -20 mm Hg LBNP with and without additional artificial (+ 10 mm Hg neck pressure) unloading of the carotid baroreceptors. There was no measurable influence of carotid unloading on forearm vascular resistance at either level of LBNP. It is concluded that forearm vascular resistance measured during cardiopulmonary baroreceptor unloading is unaffected by carotid baroreceptor unloading within the magnitude encountered during low levels of LBNP.

Thompson, Cynthia A.↗
NASA NTRS1991

Characterization of the corrosion resistance of biologically active solutions: The effects of anodizing and welding

An understanding of fabrication processes, metallurgy, electrochemistry, and microbiology is crucial to the resolution of microbiologically influenced corrosion (MIC) problems. The object of this effort was to use AC impedance spectroscopy to characterize the corrosion resistance of Type II anodized aluminum alloy 2219-T87 in sterile and biologically active media and to examine the corrosion resistance of 316L, alloy 2219-T87, and titanium alloy 6-4 in the welded and unwelded conditions. The latter materials were immersed in sterile and biologically active media and corrosion currents were measured using the polarization resistance (DC) technique.

Walsh, Daniel W.↗
NASA NTRS1991

Dynamic inter-limb resistance exercise device for long-duration space flight

Essential for fitness on Earth, resistive exercise is even more important for astronauts, who must maintain muscle and bone strength in the absence of gravity. To meet this need, designers and scientists at NASA Ames Research Center, Life Science Division, have worked to develop more effective exercise devices for long-duration exposure to microgravity. One of these concepts is the Inter-Limb Resistance Device which allows the subject to exercise one limb directly against another, strengthening muscle groups in the arms, legs, and back. It features a modular harness with an inelastic cable and instrumented pulley. Forces similar to other high resistance exercise equipment are generated. Sensors in the pulley measure force and velocity for performance feedback display and data acquisition. This free-floating apparatus avoids vibration of sensitive experiments on board spacecraft. Compact with low mass, this hardware is also well suited for a 'safe haven' from radiation on board Space Station Freedom, and may prove useful in confined environments on Earth, such as Antarctic stations, submarines, and other underwater habitats. Potential spin-offs of this technology include products for personal strengthening and cardiovascular conditioning, rehabilitation of hospital patients, fitness exercise for the disabled, and retraining after sports injuries.

Schwandt, Douglas F.↗
NASA NTRS1992

Analysis of surface wave propagation in a grounded dielectric slab covered by a resistive sheet

Both parallel and perpendicular polarized surface waves are known to propagate on lossless and lossy grounded dielectric slabs. Surface wave propagation on a grounded dielectric slab covered with a resistive sheet is considered. Both parallel and perpendicular polarizations are examined. Transcendental equations are derived for each polarization and are solved using iterative techniques. Attenuation and phase velocity are shown for representative geometries. The results are applicable to both a grounded slab with a resistive sheet and an ungrounded slab covered on each side with a resistive sheet.

Shively, David G.↗
NASA NTRS1992

The achievement of low contact resistance to indium phosphide: The roles of Ni, Au, Ge, and combinations thereof

We have investigated the electrical and metallurgical behavior of Ni, Au-Ni, and Au-Ge-Ni contacts on n-InP. We have found that very low values of contact resistivity rho(sub c) in the E-7 omega-sq cm range are obtained with Ni-only contacts. We show that the addition of Au to Ni contact metallization effects an additional order of magnitude reduction in rho(sub c). Ultra-low contact resistivities in the E-8 omega-sq cm range are obtained with both the Au-Ni and the Au-Ge-Ni systems, effectively eliminating the need for the presence of Ge in the Au-Ge-Ni system. The formation of various nickel phosphides at the metal-InP interface is shown to be responsible for the observed rho(sub c) values in the Ni and Au-Ni systems. We show, finally, that the order in which the constituents of Au-Ni and Au-Ge-Ni contacts are deposited has a significant bearing on the composition of the reaction products formed at the metal-InP interface and therefore on the contact resistivity at that interface.

Fatemi, Navid S.↗
NASA NTRS1992

Fracture resistance development in ceramic composites with nonlinear fiber pullout relationship

This paper addresses the fracture resistance mechanism in fiber reinforced ceramics, and focuses attention on the specific effects associated with nonlinear nature of the fiber pullout mechanism. The model is based on a consideration of the representative boundary value problem typical for the bridging process. The theoretical solution includes an accurate account of the nonlinear fiber matrix friction. The developed approach allows consideration of several types of nonlinear fiber pullout-force dependence. The distinct features of the nonlinear process demonstrate that, contrary to the linear case, the universal fracture resistance curves cannot be developed in cases with significant nonlinear contribution in the fiber friction law. The resulting resistance curves depend strongly on the absolute values of the matrix fracture toughness. On the other hand, these distinct patterns may be used for identification of the particular friction law and determination of the friction parameters.

Rubinstein, Asher A.↗
NASA NTRS1990

Dependence of millimeter wave surface resistance on the deposition parameters of laser ablated YBa2Cu3O(x) thin films

Measurements of millimeter-wave surface resistance versus temperature have been performed for YBa2Cu3O(x) thin films on 100 line-type SrTiO(3) substrates using a TE(011) cylindrical copper cavity at 80 GHz. The 0.6-micron thick films were grown at several deposition temperatures in the range 690 C to 810 C by means of a pulsed excimer laser ablation technique. A surface resistance minimum (60 milliohm at 77 K) near 770 C is shown to correlate with a minimum in c-axis lattice parameter (11.72 A). The highest value of Tc also occurs near this temperature. The surface resistance of films deposited at 790 C on 110 line-type LaAlO3 subtrates is lower, reaching 8 milliohm at 98 GHz and 80 K, demonstrating the influence of substate material on film quality.

Wosik, J.↗