Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REACTOR FUEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Non-Destructive Postirradiation Examination of the AFC-4C Capsule/Rodlet 5 Experiment

The AFC-4C irradiation test was irradiated at the Idaho National Laboratory Advanced Test Reactor to investigate several different fast reactor fuels that could be used to facilitate ultra-high burnup applications in sodium fast reactors. Several different alloys, fuel geometries, bonding materials, and coating/barrier were tested in ferritic-martensitic HT-9 cladding. The AFC-4C capsule 5 was removed from the reactor at around 8.7 at %HM burnup to begin postirradiation examination. This report presents and discusses the non-destructive PIE results of the AFC-4C-capsule / rodlet 5, a U-10Zr solid fuel, sodium bonded with HT9 with internal Cr-coating, and its performance is evaluated against the historical fuel performance of previously irradiated fuel from literature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NGNP Data Management and Analysis System Analysis and Web Delivery Capabilities

Projects for the Very High Temperature Reactor Technology Development Office provide data in support of Nuclear Regulatory Commission licensing of the very high temperature reactor. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high-temperature and high-fluence environments. In addition, thermal-hydraulic experiments are conducted to validate codes used to assess reactor safety. The Very High Temperature Reactor Technology Development Office has established the NGNP Data Management and Analysis System (NDMAS) at the Idaho National Laboratory to ensure that very high temperature reactor data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the third NDMAS objective. It describes capabilities for displaying the data in meaningful ways and for data analysis to identify useful relationships among the measured quantities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The effect of fuel thermal conductivity on the behavior of LWR cores during loss-of-coolant accidents

The effect of variation in thermal conductivity of light water reactor fuel elements on core response during loss-of-coolant accident scenarios is examined. Initially, a simplified numerical analysis is utilized to determine the time scales associated with dissipation of stored energy from the fuel into the coolant once the fission reaction is stopped. The analysis is then followed by full reactor system thermal-hydraulics analysis of a typical boiling and pressurized water reactor subjected to a large break loss-of-coolant accident scenario using the TRACE code. Accordingly, sensitivity analyses to examine the effect of an increase in fuel thermal conductivity, up to 500%, on fuel temperature evolution during these transients are performed. Given the major differences in thermal-hydraulics design aspects of boiling and pressurized water reactors, different fuel and temperature responses during the simulated loss-of-coolant transients are observed.

36 MATERIALS SCIENCE↗

Retrieval and Management of TRU Sludge at Hanford K-Basin - 19641

At the US Department of Energy Hanford site, the K-East and K-West reactor fuel storage basins (KE or KW Basin) were used in the 1970's and 1980's to store more than 100,000 uranium fuel rods and rod fragments that had been irradiated in the Hanford N Reactor. Approximately 2,100 metric tons of spent nuclear fuel that had been stored in the KW Basin were removed in 2004. Over time a mixture of small fuel corrosion particles, fuel rod metal fragments, and other debris accumulated in the KW Basin from the degradation of the spent nuclear fuel during storage. This is the source of the TRU sludge stored in the KW Basin. The corrosion products mixed with windblown sand, concrete dust, and other debris in the basin to form what is known as sludge. In 2006/2007 KE Basin sludge of similar origin as the KW Basin was transferred to KW Basin. Approximately 27 m{sup 3} of highly radioactive sludge was collected and consolidated underwater in six specially designed engineered containers. The mission of the Hanford Sludge Treatment Project (STP) is to develop and deploy technologies to safely retrieve, transport, and interim store the approximately 27 m{sup 3} of remote-handled transuranic (RH-TRU) sludge that is stored in the KW Basin. After extensive technology development, testing (with a bounding range of simulants), design, and procurement a sludge removal and storage system called the Engineered Container Retrieval and Transfer System (ECRTS) completed acceptance testing in 2018. The ECRTS system is designed to remotely retrieve and transport high density, highly erosive, uranium metal pieces as well as small low-density particles. The ECRTS system includes a retrieval tool based on the XAGO{sup tm} design from the United Kingdom, a heavily modified positive displacement pump, a hose-in-hose transfer system, a Sludge Transport and Storage Container (STSC), a settling and decant system, and a shielded transport system. The first sludge transfer was successfully completed on June 12, 2018 proving that the ECRTS process equipment worked as intended on the actual sludge. Three batches (i.e. transfer and decant) were required to obtain a ∼ 100% fill of the first STSC. The STSC was then transported to the on-site storage facility. Over 20 STSCs will be filled with RH-TRU sludge over approximately 16 months. This paper will discuss the issues and successes associated with this project including the operational aspects of this new system. Experience gained from this successful project should assist anyone with the need to retrieve and manage remote handled sludge from fuel storage basins. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

New fixed-point mini-cell to investigate thermocouple drift in a high-temperature environment under neutron irradiation

Temperature measurements in the nuclear field require a high degree of reliability and accuracy. Despite their sheathed form, thermocouples subjected to nuclear radiations undergo changes due to radiation damage and transmutation that lead to significant EMF drift during long-term fuel irradiation experiment. For the purpose of a High Temperature Reactor fuel irradiation to take place in the High Flux Reactor Petten, a dedicated fixed-point cell was jointly developed by LNE-Cnam and JRC-IET. The developed cell to be housed in the irradiation rig was tailor made to quantify the thermocouple drift during the irradiation (about two year duration) and withstand high temperature (in the range 950 deg. C - 1100 deg. C) in the presence of contaminated helium in a graphite environment. Considering the different levels of temperature achieved in the irradiation facility and the large palette of thermocouple types aimed at surveying the HTR fuel pebble during the qualification test both copper (1084.62 deg. C) and gold (1064.18 deg. C) fixed-point materials were considered. The aim of this paper is to first describe the fixed-point mini-cell designed to be embedded in the reactor rig and to discuss the preliminary results achieved during some out of pile tests as much as some robustness tests representative of the reactor scram scenarios. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Core conversion of the Portuguese research reactor to LEU fuel

Core conversion of the Portuguese Research Reactor (RPI) to LEU fuel is being performed within IAEA's Technical Cooperation project POR/4/016, with financial support from the US and Portugal. CERCA was selected as manufacturer of the LEU assemblies by the IAEA after an international call for bids. CERCA provided a comprehensive package to the RPI which included the mechanical verification of the design of the assemblies, their manufacture and arrangements for a joint inspection of the finished assemblies. The LEU fuel assemblies were manufactured within 8 months upon final approval of the design. The safety analyses for the core conversion to LEU fuel were made with the assistance of the RERTR program and were submitted for review by the IAEA and by Portuguese authorities in January 2007. Revised documents were submitted in June 2007 addressing the issues raised during review. Regulatory approval was received in early August and core conversion was done in early September. All measured safety parameters are within the defined acceptance limits. Operation at full power is expected by the end of October. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Sludge Removal: Success and Partnership with T Plant - 20510

U.S. DOE contractor CH2M Hill Plateau Remediation Company (CHPRC) has safely and efficiently managed the removal of highly radioactive sludge from the 105-K West Reactor fuel storage basin (105- KW Basin) near the Columbia River. In mid-September 2019, sludge retrieval was completed after 21 storage containers were safely loaded with highly radioactive sludge and transported approximately 13 miles from the 105-KW Basin to T Plant, located in the 200 West Area on the Central Plateau of the Hanford Site. Sludge removal represents the last major source term reduction necessary before the K West Reactor and fuel storage basin can transition to closure activities in preparation for final deactivation and demolition. The technical complexity of the sludge retrieval process, coupled with the challenging physical and radiological characteristics of the waste, necessitated a methodical and deliberate approach using unique design and operational solutions to safely conduct the work. This challenge was further complicated by the need to plan and conduct the work in two separate facilities, each subject to the controls and requirements of its own nuclear facility safety basis. The project overcame these challenges through creating an integrated team that actively engaged, communicated and coordinated each phase of the project to ensure successful completion. This paper will cover how these key elements of the Sludge Removal Project led to its success: - Integrating project planning and management; - Lessons learned from design and construction; - Preparing for a successful campaign (lessons learned from testing and start-up); - Lessons learned from operating in two separate facilities, transporting sludge containers on the Hanford Site and ensuring compliance with a range of regulatory and safety basis requirements. The establishment of an integrated group spanning two facilities and multiple organizations created a team capable of overcoming the challenges necessary to successfully plan and execute the sludge retrieval mission. Sharing lessons learned from this successful project can enhance the ability of teams across the DOE complex to successfully plan and execute complex projects. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Microstructural evaluation of a Fe-12Cr nanostructured ferritic alloy designed for impurity sequestration

Fast reactor fuel cladding candidate materials require proficiency in extreme environments consisting of high temperatures and irradiation doses in excess of 150 displacements per atom (dpa). Nanostructured oxide dispersion strengthened (ODS) alloys have been developed extensively for this purpose due to their notable high temperature strength, creep resistance, and irradiation resistance. However, their properties can deteriorate if interstitial impurities such as C and N are not well controlled during the fabrication process. A new Fe-12Cr nanostructured ODS alloy OFRAC (Oak Ridge Fast Reactor Advanced Fuel Cladding) with solute additions of Mo, Ti, and Nb has been developed to provide the desired properties mentioned above while simultaneously sequestering impurities within the matrix. After extrusion at 850°C, the as-extruded microstructure consists of an average 490 nm grain size and a high number density (6.8 × 10 23 m -3 ) of 2.2 nm diameter (Y,Ti,O) nanoclusters distributed homogeneously in the matrix. Atom probe tomography investigations suggest non-stochiometric compositions for the smallest nanoclusters. In addition, a second population of nanometer scale (Nb,Ti) rich carbonitrides is also present in the microstructure that captures the potentially detrimental C and N impurity atoms present in the matrix. Atom probe tomography results indicate elemental segregation of Cr, Mo, and Nb to grain boundaries in the as-extruded material, consistent with previous investigations of solid solution strengthening by solute additions. In conclusion, the ability of OFRAC to sequester impurities introduced from the powder metallurgical approach to nanostructured ferritic alloy development, compounded with its beneficial mechanical properties, makes this alloy a competitive candidate for fast reactor applications.

36 MATERIALS SCIENCE↗

Iodine transport analysis in the ESBWR.

A simplified ESBWR MELCOR model was developed to track the transport of iodine released from damaged reactor fuel in a hypothesized core damage accident. To account for the effects of iodine pool chemistry, radiolysis of air and cable insulation, and surface coatings (i.e., paint) the iodine pool model in MELCOR was activated. Modifications were made to MELCOR to add sodium pentaborate as a buffer in the iodine pool chemistry model. An issue of specific interest was whether iodine vapor removed from the drywell vapor space by the PCCS heat exchangers would be sequestered in water pools or if it would be rereleased as vapor back into the drywell. As iodine vapor is not included in the deposition models for diffusiophoresis or thermophoresis in current version of MELCOR, a parametric study was conducted to evaluate the impact of a range of iodine removal coefficients in the PCCS heat exchangers. The study found that higher removal coefficients resulted in a lower mass of iodine vapor in the drywell vapor space.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Preliminary modeling of triply periodic minimal surface (TPMS) structures using RELAP5-3D

With the United States Department of Energy (DOE)’s goal of quadrupling the nation’s nuclear energy supply by 2050, and with the Advanced Fuels Campaign pushing for new types of advanced reactor fuels and geometries, the need has arisen for new nuclear fuel designs. One such design is to swap out current nuclear fuel geometries in exchange for another type of geometry, called a Triply Periodic Minimal Surface (TPMS). TPMSs are self-supporting, infinitely repeating lattices—attributes that lend themselves well to additive manufacturing. These surfaces also possess enhanced heat transfer properties thanks to their internal area changes and large surface-area-to-volume ratios. Their drawback, however, is an increased pressure drop. Given the small amount of correlations and data (Reynolds numbers in the 2,000–8,000 range), and the minimal amount of experience so far obtained by modeling TPMS structures using 1D systems codes such as the Reactor Excursion and Leak Analysis Program (RELAP5-3D), further research into this topic was needed. Using data from the University of Wisconsin - Madison (UW), curve fits were created for both a Heat Transfer Coefficient (HTC) correlation and a Darcy friction factor empirical coefficient correlation. The curves’ coefficients and multipliers were then output and utilized in RELAP5-3D models of two upcoming experiments—Flow Loop for INFLUX Pressure drop (FLIP) and Microreactor Agile Non-nuclear Experimental Test (MAGNET)—aimed at increasing the available data for Reynolds numbers to the 16,000–36,000 range for TPMS structures. The models were run under the conditions utilized by a Computational Fluid Dynamics (CFD) analysis performed by another group at Idaho National Laboratory. Only CFD pressure drop values were obtained from the FLIP test, and those values showed that the RELAP5-3D models had a lower rate of pressure increase in comparison to the CFD values. In addition, there seemed to be a vertical shift upward in the pressure drop for both models whenever the TPMS porosity decreased, and the RELAP5-3D models showed a higher vertical shift in comparison to the CFD values. The MAGNET results did not correspond to any CFD or experimental results against which they could be compared, so they were instead compared against the proposed CFD input conditions. These values were then compared with each other to make sure the model seemed to be performing as expected, paving the way for future tests that can be run for the purpose of further analyses and comparisons. The pressure drop increased with temperature and mass flow rate independently. The temperature change would decrease with increasing mass flow rate and temperature, which was just as we expected based on the fact that the lower viscosity and decreased density would result in higher friction and churning losses. The last metric that was assessed was the enthalpy flow change, which increased with increasing mass flow rate and decreasing temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sensitivity and uncertainty analysis for a combined depletion and criticality calculation chain of a BWR FA

This paper examines the prerequisites and boundary conditions for extending burnup credit from pressurized water reactors to boiling water reactors with validated depletion codes by performing uncertainty and sensitivity analyses on a modern boiling water reactor fuel assembly design. We developed a computational chain consisting of an axial boiling water reactor axial irradiation model, followed by a series of depletion calculations and a three-dimensional criticality calculation. The irradiation model puts into relation the profiles of power, burnup and moderator density of the fuel assembly at 24 axial locations. In a simplified fashion it also includes the insertion of control blades. The depletion calculations of the fuel assembly were performed in axial slices with the 2D-depletion code HELIOS 1.12. The criticality calculations were done in 3D-geometry with KENO-Va from the SCALE 6.2.1 package, in which several fuel assemblies are placed into a generic transport cask. For the uncertainty and sensitivity analyses a Monte Carlo sampling based approach is used applying the GRS tool SUnCISTT. We performed several generic investigations testing the capabilities and the limitations of the whole computational chain. The impact of variations of the irradiation model on the resulting reactivity of the fuel assemblies inside a transport cask or storage pool was investigated using an uncertainty and sensitivity analysis on the whole computational chain. Geometrical uncertainties were also included in the evaluation and a parameter study on the use of control blades during irradiation was performed. The goal was to develop the procedures and tools to be able to obtain quantitative uncertainty data which can be used in the future to derive conservative irradiation profiles without unnecessary excess reactivity margins. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Preliminary Results of Ancillary Safety Analyses Supporting TREAT LEU Conversion Activities

The Transient Reactor Test Facility (TREAT), located at Idaho National Laboratory (INL), is a test facility designed to evaluate the performance of reactor fuels and materials under transient accident conditions. The facility, an air-cooled, graphite-moderated reactor designed to utilize fuel containing high-enriched uranium (HEU), has been in non-operational standby status since 1994. Currently, in support of the missions of the Department of Energy (DOE) National Nuclear Security Administration (NNSA) Material Management and Minimization (M3) Reactor Conversion Program, a new core design is being developed for TREAT that will utilize low-enriched uranium (LEU). The primary objective of this conversion effort is to design an LEU core that is capable of meeting the performance characteristics of the existing HEU core. Minimal, if any, changes are anticipated for the supporting systems (e.g. reactor trip system, filtration/cooling system, etc.); therefore, the LEU core must also be able to function with the existing supporting systems, and must also satisfy acceptable safety limits. In support of the LEU conversion effort, a range of ancillary safety analyses are required to evaluate the LEU core operation relative to that of the existing facility. These analyses cover neutronics, shielding, and thermal hydraulic topics that have been identified as having the potential to have reduced safety margins due to conversion to LEU fuel, or are required to support the required safety analyses documentation. The majority of these ancillary tasks have been identified in [1] and [2]. The purpose of this report is to document the ancillary safety analyses that have been performed at Argonne National Laboratory during the early stages of the LEU design effort, and to describe ongoing and anticipated analyses. For all analyses presented in this report, methodologies are utilized that are consistent with, or improved from, those used in analyses for the HEU Final Safety Analysis Report (FSAR) [3]. Depending on the availability of historical data derived from HEU TREAT operation, results calculated for the LEU core are compared to measurements obtained from HEU TREAT operation. While all analyses in this report are largely considered complete and have been reviewed for technical content, it is important to note that all topics will be revisited once the LEU design approaches its final stages of maturity. For most safety significant issues, it is expected that the analyses presented here will be bounding, but additional calculations will be performed as necessary to support safety analyses and safety documentation. It should also be noted that these analyses were completed as the LEU design evolved, and therefore utilized different LEU reference designs. Preliminary shielding, neutronic, and thermal hydraulic analyses have been completed and have generally demonstrated that the various LEU core designs will satisfy existing safety limits and standards also satisfied by the existing HEU core. These analyses include the assessment of the dose rate in the hodoscope room, near a loaded fuel transfer cask, above the fuel storage area, and near the HEPA filters. The potential change in the concentration of tramp uranium and change in neutron flux reaching instrumentation has also been assessed. Safety-significant thermal hydraulic items addressed in this report include thermally-induced mechanical distortion of the grid plate, and heating in the radial reflector.

Brunett, A. J.↗

Preliminary study on new configuration with LEU fuel assemblies for the Dalat nuclear research reactor

The fuel conversion of the Dalat Nuclear Research Reactor (DNRR) is being realized. The DNRR is a pool type research reactor which was reconstructed from the 250 kW TRIGA- MARK II reactor. The reconstructed reactor attained its nominal power of 500 kW in February 1984. According to the results of design and safety analyses performed by the joint study between RERTR Program at Argonne National Laboratory (ANL) and Vietnam Atomic Energy Commission (VAEC) the mixed core of irradiated HEU and new LEU WWR-M2 fuel assemblies will be created soon. This paper presents the results of preliminary study on new configuration with only LEU fuel assemblies for the DNRR. The codes MCNP, REBUS and VARI3D are used to calculate neutron flux performance in irradiation positions and kinetics parameters. The idea of change of Beryllium rod reloading enables to get working configuration assured shutdown margin, thermal-hydraulic safety and increase in thermal neutron flux in neutron trap at the center of DNRR active core. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Pebble bed modular reactor safeguards: developing new approaches and implementing safeguards by design

The design of the Pebble Bed Modular Reactor (PBMR) does not fit or seem appropriate to the IAEA safeguards approach under the categories of light water reactor (LWR), on-load refueled reactor (OLR, i.e. CANDU), or Other (prismatic HTGR) because the fuel is in a bulk form, rather than discrete items. Because the nuclear fuel is a collection of nuclear material inserted in tennis-ball sized spheres containing structural and moderating material and a PBMR core will contain a bulk load on the order of 500,000 spheres, it could be classified as a 'Bulk-Fuel Reactor.' Hence, the IAEA should develop unique safeguards criteria. In a multi-lab DOE study, it was found that an optimized blend of: (i) developing techniques to verify the plutonium content in spent fuel pebbles, (ii) improving burn-up computer codes for PBMR spent fuel to provide better understanding of the core and spent fuel makeup, and (iii) utilizing bulk verification techniques for PBMR spent fuel storage bins should be combined with the historic IAEA and South African approaches of containment and surveillance to verify and maintain continuity of knowledge of PBMR fuel. For all of these techniques to work the design of the reactor will need to accommodate safeguards and material accountancy measures to a far greater extent than has thus far been the case. The implementation of Safeguards-by-Design as the PBMR design progresses provides an approach to meets these safeguards and accountancy needs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Detailed Fission Power 2D-Mapping of AFIP-2 Experiment in ATR CFT Position

The NNSA (National Nuclear Security Administration) RERTR (Reduced Enrichment for Research and Test Reactors) program assigned INL (Idaho National Laboratory) the responsibility of developing and demonstrating high uranium density research reactor fuel forms to enable the use of low enriched uranium (LEU) in the research reactors around the world. A series of full-size fuel plate irradiation tests are proposed for the ATR (Advanced Test Reactor). Labeled the AFIP (ATR Full-size-plates In center flux trap Position) experiments, these tests will be conducted in the ATR center flux trap. The AFIP-2 experiment will contain two full size fuel plates fabricated at the Oak Ridge National Laboratory-Y-12 (ORNL). The nominal fuel zone is rectangular in shape having a designed length of 21.5-in (54.6l-cm), width of 1.6-in (4.064-cm), and uniform thickness of 0.014-in (0.03556-cm). This gives a nominal fuel zone volume of 0.482 in3 (7.89 cm3) in each fuel plate. The test holder accommodates two independent test trains. Each test train is designed to hold 2 plates, for a total of 4 plates per test holder. AFIP-2 test plates will be irradiated at a peak surface heat flux of about 350 W/cm2 and discharged at a peak U-235 burn-up of about 70 at.%. Based on limited irradiation testing of the monolithic (U10Mo) fuel form, it is desirable to keep the peak fuel temperature below 250°C; to achieve this, it will be necessary to keep plate heat fluxes below 500 W/cm2. Due to the heavy U-235 loading and width of 1.6-in (4.064 cm), the neutron self-shielding will increase the local-to-average-ratio fission power near the sides of the fuel plates. To assure the AFIP-2 experiment will comply with the ATR safety requirements, a very detailed 2 dimensional (2D) Y-Z fission power profile was evaluated to best predict the fuel plate temperature distribution. The ability to accurately predict fuel plate power and burnup are essential in the AFIP-2 fuel test train design and the irradiated fuel performance evaluation. We obtained the required power and heat generation rates within test train for the thermal analyses. A detailed MCNP Y-Z mini-plate fuel model was developed. The Y-Z model divides each fuel mini-plate into 30 equal intervals in Y and Z directions. The MCNP-calculated results and the detailed Y-Z fission power mapping were used to help design the AFIP-2 fuel test assembly to ensure that the capsule thermal-hydraulic limits will not exceed the ATR safety limit.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reactor Physics Analysis of Transitioning to a Thorium Fuel Cycle with Molten Salt Reactors

Commercial power reactors operating in the United States are light-water reactors (LWRs) fueled with low-enriched uranium (LEU) in a once-through fuel cycle; the important fissile isotopes are {sup 235}U, {sup 239}Pu, and {sup 241}Pu. In a thorium fuel cycle, the fertile isotope {sup 232}Th is converted into {sup 233}U, a fissile isotope that is not naturally occurring. In transitioning from the once-through fuel cycle to the thorium fuel cycle, the availability of man-made {sup 233}U presents a challenge: without it, the initial fissile material fueling the first reactors built in this transition is not the fissile isotope that the reactor is breeding. The transition requires an alternate fissile material until enough surplus {sup 233}U is available to start up additional reactors. In liquid-fueled molten salt reactors (MSRs), the fuel is dissolved into molten salt, which is continuously circulated through the core, simultaneously undergoing irradiation, chemical treatments and separations, and feeds. MSRs are an attractive technology in which the thorium fuel cycle can be deployed, as the {sup 233}U bred from {sup 232}Th is continuously being recycled back through the core. The bred fissile material is immediately available to fuel the core without processing or fuel fabrication. After start-up, only a fertile {sup 232}Th feed is necessary to sustain criticality in the MSR. But, in single-fluid MSRs, the initial fissile and fertile materials are mixed into the same molten fuel salt, complicating separations of initial and bred fissile materials. In solid-fuel systems, these materials are often separate. This analysis herein builds on previous work modeling thorium-fueled MSR start-up. It is based on unit cell representations of the graphite-moderated, 2250 MWt Oak Ridge National Laboratory (ORNL) Molten Salt Breeder Reactor (MSBR). This paper discusses the start-up of the first MSR in the transition to a thorium fuel cycle and identifies challenges and limitations of fuel cycle deployment with this reactor technology. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Proposed Subcritical Assembly for Nuclear Criticality Safety Training at the Oak Ridge National Laboratory

The design of a new subcritical assembly at Oak Ridge National Laboratory (ORNL) has been finalized. This design takes the feasibility study of the subcritical assembly performed in August 2020 to an implementable design. This subcritical assembly will support the Nuclear Criticality Safety Program (NCSP) training and education program. The addition of this subcritical assembly into the NCSP training and education will enhance the program by providing backup capacity for training if nuclear facility operations are disrupted at Sandia National Laboratories or the National Criticality Experiments Research Center; providing a new location that is more accessible to students in the Eastern portion of the United States; providing flexibility to support students from a diverse background (e.g., university students, foreign nationals). The proposed subcritical assembly uses legacy AGN-201M research reactor fuel plates that are available at the Y-12 National Security Complex. The final design of this subcritical assembly contains approximately 617 grams of 235 U as UO 2 powder distributed homogeneously in polyethylene. The fuel plates will have a graphite neutron reflector to obtain a core multiplication, M, from 10 to 20, corresponding to a $k_{eff}$ of 0.90 to 0.95, respectively. The subcritical assembly will be able to support at least four experiments for the training courses: (1) the addition of fissile material to the core (mass), (2) a core separation experiment (interaction), (3) the addition of moderators to the core (moderation), and (4) the addition of neutron absorbers to the core (poison/absorption). The subcritical assembly will be designed to be inherently safe—subcritical under all normal and abnormal conditions— and will provide the capability to conduct hands-on training to support NCSP and general nuclear criticality safety staff training and qualification goals.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

U.S. Department of Energy & Nuclear Regulatory Commission Advanced Fuel Cycle Research & Development Seminar Series FY 2007 & 2008

In fiscal year 2007, the Advanced Burner Reactor project initiated an educational seminar series for the Department of Energy (DOE) and Nuclear Regulatory Commission (NRC) personnel on various aspects of fast reactor fuel cycle closure technologies. This important work was initiated to inform DOE and NRC personnel on initial details of sodium-cooled fast reactor, separations, waste form, and safeguard technologies being considered for the Advanced Fuel Cycle Research and Development program, and to learn the important lesson from the licensing process for the Clinch River Breeder Reactor Plant that educating the NRC staff early in the regulatory process is very important and critical to a project success.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗