Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RAMAN SPECTROSCOPY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Vivianite oxidation is not photocatalyzed

Vivianite is a hydrous Fe2+ phosphate mineral found in anoxic environments that plays an integral role in P cycling and environmental biogeochemistry. Imbued in the vivianite literature dating as far back as 1918 is the notion that vivianite is light-sensitive and susceptible to rapid photooxidation induced entirely by solar light. However, despite an exhaustive search, to our knowledge this conventionally accepted assumption has never been directly tested, nor has the band gap ever been measured. Resolving this question of photochemical control of vivianite redox chemistry is important for performing and interpreting experiments involving vivianite reactivity with contaminants, and potentially iron and phosphate cycling in the photic zone of aquatic systems. The present study was specifically designed to add¬ress this question. Pure synthetic vivianite samples were irradiated in aqueous suspensions with a Xe lamp at conditions mimicking the solar spectrum and compared to dark controls. Particles stirred in anoxic suspensions for up to 66 days showed no detectable oxidation irrespective of light exposure, according to colorimetric Fe2+/Fe3+ assays, micro X-ray diffraction, and Raman spectroscopy. In contrast, the same experiment performed using air-equilibrated suspensions showed systematic oxidation of up to ~80% mol% Fe(II) at 66 days, but again with no detectable light exposure effect. To test for UV reactivity, further experiments on vivianite powders under air versus N2 atmosphere were performed using a Hg lamp with a longpass filter. In contrast to oxidation in air where no effect of light was detected, after 24 hrs irradiation anoxically, 0.78% Fe was oxidized compared to dark controls, and after 13 days only an additional 0.3% Fe was oxidized. The band gap of pure vivianite was measured by the Tauc method to be 3.5 eV. Contrary to previous reports, solar light has minimal impact on the oxidation of pure vivianite, insignificant in particular when compared to its relatively fast oxidation by oxygen exposure. As such, light does not need to be excluded when running typical vivianite laboratory experiments. Long-term storage of natural vivianite in museums or private collections should continue protective measures given that a possible photocatalytic role of impurities cannot yet be ruled out. Nonetheless, at all depths in natural aquatic systems it appears that the primary abiotic control on the reactivity and half-life of vivianite particles should be the dissolved oxygen concentration, not light exposure.

Vivianite, photochemistry, oxidation↗
DOE OSTI2024

Optically induced quantum transitions in direct probed mesoscopic NbSe 2 for prototypical bolometers

Superconducting transition-edge sensors (TES) have emerged as fascinating devices to detect broadband electromagnetic radiation with low thermal noise. The advent of metallic transition metal dichalcogenides, such as NbSe 2 , has also created an impetus to understand their low-temperature properties, including superconductivity. Interestingly, NbSe 2 -based sensor within the TES framework remains unexplored. In this work, direct-probed superconducting NbSe 2 absorbers led to a proof-of-concept demonstration for the transduction of incoming light to heat, where a thermodynamic superconducting phase transition in NbSe 2 was evident to switch it to the normal-state, when biased below its superconducting transition temperature. A wavelength-dependent response of its optical absorption properties was observed, based on the incident optical excitation source used. Furthermore, extensive optical characterization studies were conducted using Raman spectroscopy, where the in-plane and out-of-plane thermal conductivity was empirically determined. Our results open new possibilities for the use of NbSe 2 in superconducting radiation detectors, including in a TES framework

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Phase stabilization and oxidation of a continuous composition spread multi-principal element (AlFeNiTiVZr) 1-x Cr x alloy

Multi-Principal Element Alloys (MPEA) have been hypothesized to maintain a stable single alloy phase and resist corrosion at high temperatures, which are desirable in various functional applications, including material of turbine blades. However, studies into oxidation resistant alloys have been constrained to individual MPEA systems or a limited selection of compositions within those systems. Here, High-Throughput Experimental (HTE) techniques were utilized to rapidly assess phase stability and resistance to oxidation of an (AlFeNiTiVZr) 1-x Cr x continuous composition spread (CCS) thin-film alloy system. High-throughput synchrotron diffraction and Raman spectroscopy were used to identify phases, especially high symmetry structures and oxides, as a function of annealing time and composition. The formation of two distinct phase regions, R 1 and R 2 , across the CCS was observed. One of these phase regions, R 2 , exhibited a stable high symmetry BCC-like phase at Cr concentrations greater than 25.4 at%, and grew a passivating mixed metal surface oxide; whereas, the R 1 phase region, decomposed on oxidation to multiple oxides and reacted with the substrate to form silicides. The passivating mixed metal oxide layer appears to prevent destabilization of the (AlFeNiTiVZr) 1-x Cr x MPEA BCC solid solution. Furthermore, at longer annealing times the passivating phase was seen only above 29.2 at% Cr. High Cr-doped (AlFeNiTiVZr) 1-x Cr x appear to be a good candidate for high temperature, oxidation-resistant structural alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-operando surface-sensitive probing of electrochemical reactions on nanoparticle electrocatalysts: Spectroscopic characterization of reaction intermediates and elementary steps of oxygen reduction reaction on Pt

In this paper we present an in-operando spectroscopic study of the reaction intermediates involved in ORR on electrified Pt nanoparticle electrocatalysts. To accomplish this, we have synthesized Ag-Pt core–shell nanoparticles, that contain a thin shell of Pt (~1 nm) uniformly deposited on a larger Ag core (~60 nm). We show that these nanostructures are ideal platforms for in-operando Plasmon Enhanced Raman Spectroscopy (PERS) of ORR on Pt. We combined these PERS studies with DFT calculations to assign the measured vibrational spectra to relevant surface intermediates as a function of electrocatalyst potential. Overall, these vibrational assignments were further verified and validated by performing PERS measurements using de-oxygenated and heavy oxygen (O 2 -18) saturated electrolyte. These studies allowed us to identity the presence of critical reaction intermediates (OH, O 2 , OOH, and H 2 O) as the function of operating voltage on the Pt surface and derive voltage-dependent elementary step mechanisms of the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The impact of feedstock size and composition on the hydrothermal growth of (U,Th)O 2

Bulk crystal growth of refractory oxides requires unique approaches, and the U x Th 1-x O 2 solid solution is no exception. Hydrothermal transport reactions of U 0.1 Th 0.9 O 2 onto ThO 2 seeds with feedstocks comprised of U 0.1 Th 0.9 O 2 or mixtures of UO 2 and ThO 2 with a nominal composition of U 0.1 Th 0.9 O 2 are investigated with µ-Raman spectroscopy and X-ray fluorescence. In each case, the trends in stoichiometry as a function of distance from the seed are analyzed and the deviations from the nominal stoichiometry discussed. When the feedstock is composed of mixed oxides, the particle surface area’s influence on the feedstock dissolution rate is the dominant factor and can produce U-rich stoichiometries as high as U 0.75 Th 0.25 O 2 . When composed solely of U 0.1 Th 0.9 O 2 , the total growth amount depends on the particle size, but the obtained stoichiometry is the product of differing solubilities. Although the U0.1Th0.9O 2 feedstock produces the most homogeneous growth, the ending growth of the smallest particle UO 2 /ThO 2 mixture yields the stoichiometry closest to U 0.1 Th 0.9 O 2 . How to obtain desired stoichiometries from mixtures by matching the particle size and solubilities is briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding fluorine-free electrolytes via small-angle X-ray scattering

Fluorine-free electrolytes have attracted great attention because of its low-cost and environmental friendliness. However, so far, little is known about the solution structures of these electrolytes. Here, we compare the solvation phenomenon of sodium tetraphenylborate (NaBPh 4 ) salt dissolved in organic solvents of propylene carbonate (PC), 1,2-dimethoxyethane (DME), acetonitrile (ACN) and tetrahydrofuran (THF). Small-angle X-ray scattering (SAXS) reveals a unique two-peak structural feature in this salt concentrated PC electrolyte, while solutions using other solvents only have one scattering peak. Molecular dynamics (MD) simulations further reveal that there are anion-based clusters in addition to the short-range charge ordering in the concentrated NaBPh4/PC electrolyte. Raman spectroscopy confirms the existence of considerable contact ion pairs (CIPs). Here, this work emphasizes the importance of global and local structural analysis, which will provide valuable clues for understanding the structure performance relationship of electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2021

Evolution of the structure and chemical composition of the interface between multi-component silicate glasses and yttria-stabilized zirconia after 40,000 h exposure in air at 800 °C

The chemical and structural stability of two commercial multicomponent silicate glasses (SCN and G6) in contact with yttria-stabilized zirconia (YSZ) was investigated after exposure times of up to 40,000 h in air at 800 °C. With exposure time, interfacial layers develop at the SCN-YSZ and G6-YSZ interfaces, which were characterized in detail using both quantitative chemical analysis and atomic-resolution imaging. At the SCN-YSZ interface, a Ca-Ba-Si-O reaction phase was found to grow by diffusion control. In G6-YSZ, Raman spectroscopy and electron microscopy revealed a disorganized interfacial reaction later between G6 and YSZ, and the occurrence of cubic to tetragonal to monoclinic phase transformations in YSZ. Finally, this microstructural evolution is discussed in terms of devitrification resistance of glass and diffusion processes at interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The role of surface hydroxyls on the radiolysis of gibbsite and boehmite nanoplatelets

Understanding mechanistic pathways to radiolytic hydrogen generation by metal oxyhydroxide nanomaterials is challenging because of the difficulties of distinguishing key locations of OH bond scission, from structural interiors to hydroxylated surfaces to physi-sorbed water molecules. In this work we exploited the interface-selectivity of vibrational sum frequency generation (VSFG) to isolate surface versus bulk hydroxyl groups for gibbsite and boehmite nanoplatelets before and after 60 Co irradiation at dose levels of approximately 7.0 and 29.6 Mrad. While high-resolution microscopy revealed no effect on particle bulk and surface structures, VSFG results clearly indicated up to 83% and 94% radiation-induced surface OH bond scission for gibbsite and boehmite, respectively, a substantially higher proportion than observed for interior OH groups by IR and Raman spectroscopy. Electron paramagnetic spectroscopy revealed that the major radiolysis products bound in the mineral structures are trapped electrons, O , O 2 – and possibly F-centers in gibbsite, and H , O and O 3 – in boehmite, which persist on the time frame of several months. The entrapped radiolysis products appear to be highly stable, enduring re-hydration of particle surfaces, and likely reflect a permanent adjustment in the thermodynamic stabilities of these nanomaterials.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Characterization of the microstructure of yttrium hydride under proton irradiation

High moderation per unit volume solid moderator materials like yttrium hydride (YH x ) are necessary for compact nuclear microreactors. However, the phase stability and hydrogen transport processes of YH x under high-temperature irradiation are largely unknown. Proton irradiation was conducted on YH x at 300 °C and 580 °C to 0.2 dpa using 1 MeV or 2 MeV protons in a high-vacuum environment. The hydrogen concentration was determined before and after irradiation using elastic recoil detection analysis, and microstructural evolution was examined via post-irradiation scanning transmission electron microscopy and Raman spectroscopy. Dislocation loops and cavities were observed in all conditions; their distribution was correlated with the bombarding proton energy and ion irradiation temperature. This work revealed that hydrogen retention is proportional to the formation of traps for hydrogen gas atoms and identified pathways for hydrogen release. The relative contributions of bulk or fast diffusion paths, such as grain boundaries, delamination boundaries, and stacking faults are discussed; the primary mechanisms of hydrogen loss are likely based on diffusion, ruling out artefacts of the experimental design. In conclusion, the study suggests proton irradiation may be a strong surrogate to study hydrogen transport in hydride moderator materials under irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Review of SiC material development for nuclear fusion applications: Cross-cutting research and emerging opportunities

The SiC-based materials, particularly SiC-fiber-reinforced SiC matrix (SiC/SiC) composites, show strong potential for structural and functional applications in future fusion power plants because they can operate at high temperatures with a range of coolants and breeders, thereby enabling higher energy conversion efficiency. Here, this paper presents recent advancements in the development of SiC-based materials, focusing on processing techniques and material performance and resistance under fusion-relevant environments. The processing activities have emphasized near-net-shape fabrication and the joining of SiC subcomponents, with processing methods and material compositions informed by previous irradiation experiments on various grades of SiC. Research on irradiation effects has remained focused on degradation mechanisms and the microstructural optimization of SiC/SiC composites irradiated to high neutron damage levels. Analysis of irradiation defects in SiC has advanced via the application of cutting-edge characterization methods, among which Raman spectroscopy is becoming a common tool to assess atomic-scale chemical disorder. Fusion–fission crosscutting irradiation research has explored combined effects in SiC/SiC composites with application-relevant geometries, including bowing of SiC/SiC composite channels under neutron flux gradients, stress evolution in SiC/SiC composite tubes under through-thickness temperature gradients, and irradiation-enhanced corrosion in SiC. Finally, research opportunities for component testing and assessment under fusion-relevant conditions, in support of emerging concepts from the private fusion sector, are discussed.

Advanced manufacturing↗
DOE OSTI2026

Effects of high-dose neutron irradiation at light-water reactor relevant temperature on the mechanical properties of SiC/SiC composites

For this study, the neutron dose-dependent evolutions and the underlying mechanisms of properties of SiC fiber-reinforced SiC matrix (SiC/SiC) composites at a temperature relevant to light-water reactors (∼600 K) were investigated and analyzed. Chemical vapor infiltrated (CVI) SiC/SiC composites reinforced with Hi-Nicalon Type S or Tyranno SA3 fiber were neutron-irradiated to doses up to 30 dpa. The irradiated composites retained their flexural strengths. The thermal diffusivity and dimensional changes were mostly retained from 2.0 to 30.2 dpa. Discrepancies in irradiation responses among CVI SiC/SiC composites from different sources were found. Additional microstructural analysis using Raman spectroscopy and numerical analysis on irradiation effect on residual stress were used to explain how the microstructural variables, especially of carbon interphases, affect the mechanical properties in the 30–40 dpa dose range.

Continuous fiber-reinforced ceramic matrix composi↗
DOE OSTI2023

Ethanol-fueled metal supported solid oxide fuel cells with a high entropy alloy internal reforming catalyst

High-performance metal supported solid oxide fuel cells (MS-SOFC) with an integrated high entropy alloy (HEA) internal reforming catalyst (IRC) are demonstrated for transportation applications using ethanol and methanol as fuels. Addition of the HEA IRC dramatically improves cell performance and stability when using ethanol/water blend fuel. Absence of carbon deposition predicted by thermodynamic calculations is confirmed by Raman spectroscopy analysis of posttest anodes. Optimal catalyst processing (deposition technique, loading, firing temperature) and cell operation conditions (flow rates, temperature, fuel compositions) are explored. Infiltrated HEA reforming catalyst provides a highly porous structure and low catalyst loading (6 mg cm –2 ). The designed structure and catalysts achieve small mass transport resistances in the fuel electrode (26.2 s m –1 ) and oxygen electrode (41.6 s m –1 ). The best ethanol concentration (60:40 v% ethanol: water) provides 0.83 W cm –1 at 700 °C, without carbon deposition. The ethanol-fueled MS-SOFC is operated for 500 h, including five thermal cycles. As a result, cell evolution is similar to that reported previously for hydrogen fuel; nickel aggregation and chromia deposition were the major observed changes, and carbon formation can be avoided even after long-term operation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Origin of deactivation of aqueous Na–CO 2 battery and mitigation for long-duration energy storage

Here, the development of long-duration energy storage technology is crucial to facilitate the efficient utilization of renewable energy sources while mitigating carbon dioxide production. In this study, we investigate the deactivation and reactivation mechanisms of the aqueous Na–CO 2 battery during extended cycling. We have designed the cathode to include non-precious intermetallic catalysts. As the cell undergoes repeated cycles, the voltage polarization during discharge progressively rises, eventually leading to the cell's deactivation and formation of decomposition products clogging the electrode surface. Results obtained from comprehensive characterization techniques, including conductive atomic force microscopy (cAFM), Raman spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and inductively coupled plasma-mass spectrometry provide insight into the decomposition products. We also showcase an electrochemical approach for regeneration of these aqueous cells. Our findings, along with the insights we have gained, provide a path toward creating long-duration systems with self-healing properties.

25 ENERGY STORAGE↗
DOE OSTI2022

Electron doping of NdNiO 3 thin films using dual chamber CaH 2 annealing

Hydrogen donor doping has been exploited as a strategy to manipulate the electronic structure and electrical properties of functional oxide systems. Especially, the development of synthetic methods to achieve electron doping of perovskite rare-earth nickelate thin films utilizing interstitial hydrogen is highly desirable considering the rich electronic phase diagram hosting several functional properties. Here, in this work, we present the hydrogenation of NdNiO 3 (NNO) thin films using CaH 2 annealing and the resulting giant modulation of electrical resistivity in hydrogenated NNO (H–NNO) thin films. Magnetron sputtering was employed to deposit epitaxial ~60 nm-thin NNO films on single crystal LaAlO 3 (LAO) substrates. The formation of the pristine perovskite NNO phase was realized after annealing the films at 500 °C for 24 h. CaH 2 annealing of NNO thin films for time durations ranging from 1 to 6 h was performed in a vacuumed ampule with two interconnected chambers at 280 °C. The two-chamber design enables a simple and clean approach for hydrogen doping without physical contact between the powder and sample of interest. X-ray diffraction and Raman spectroscopy revealed the formation of NNO in pristine samples, and the subsequent hydrogen incorporation upon CaH 2 annealing without forming any impurity phases. The conversion of the oxidation state of Ni towards +2 upon CaH 2 annealing was probed using X-ray photoelectron spectroscopy and X-ray absorption spectroscopy. Consequently, a substantial increase in the room-temperature resistivity was observed upon CaH 2 annealing indicating the formation of a strongly correlated electronic configuration of Ni in H–NNO due to electron doping. Overall, the findings of this study highlight the versatility of CaH 2 annealing as an electron doping method to tune the electrical properties of correlated oxides at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synthesis and characterization of the rare-earth chloride complexes with N,N,N',N' -tetramethylmalonamide

Exploration of the solid-state chemistry of the f-elements and their coordination chemistry can assist in understanding the speciation of these elements in solution, which, in turn, can aid in the interpretation of their chemical behavior in complex liquid-liquid separations. Within these separation processes, malonamides are common organic extractants that are used for complexing both lanthanides and actinides, thus it is relevant to understand the malonamide ligand complexation under various conditions. In this work, we investigate solid-state complexes of the rare-earth chlorides with N,N,N',N' -tetramethylmalonamide (TMMA) across the entire lanthanide series. Here, we isolated two structural families of compounds Ln(TMMA) 2 Cl 3 Ln = La–Dy and [Ln(TMMA) 2 (H 2 O) 4 ]Cl 3 • x H 2 O x = 0,4 Ln = Ho–Lu, showing differences in chloride coordination from the inner-sphere complex for early lanthanides to outer-sphere for the late lanthanides. Both structural series were additionally analyzed by both IR and Raman spectroscopy confirming similarities in malonamide ligand coordination modes, while showing differences in vibrational features associated with chloride and aqua ligand coordination.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear fuel cladding material

Silicon carbide (SiC)-based nuclear fission fuel rod cladding has been considered as one of the possible designs for accident tolerant fuels. It is in the form of a SiC fibre reinforced SiC matrix composite tube (SiC f -SiC m ) with monolithic SiC outer and/or inner coating layers. This study focuses on the deformation and fracture processes in this material using in situ X-ray micro-computed tomography (XCT) at room temperature (RT) and 1200 °C in an inert gas environment in a C-ring compression loading configuration. Prior to testing, local properties and residual stresses were characterised using nanoindentation and Raman spectroscopy since they can impact the mechanical behaviour of the material. The 3D strain distribution, crack formation and propagation processes including the toughening mechanisms (e.g., crack deflection, micro-cracking, crack bridging and bifurcation) are investigated in the coating and underlying composites at RT and 1200 °C. There is no particular sequence which toughening mechanism occurs first – this is very different from the conventional toughening theory in ceramic-matrix composites under uniaxial tension loading. Indeed, no evidence of fibre pull-out or fibre fracture was observed in this SiC f -SiC m nuclear cladding material in the current C-ring compression configuration. The correlation between local measurements and bulk mechanical behaviour are discussed.

3D imaging↗
DOE OSTI2025

Glassy carbon formation from pyrolysis of polymeric coatings on fiber-optic sensors

Deploying fiber-optic sensors in nuclear reactors requires a detailed understanding of radiation effects on the fiber materials and the transmitted signals. Previous work has shown large wavelength shifts in the reflected spectra obtained from polymer-coated fiber-optic temperature sensors exposed to high neutron fluences. The sensor drift resulting from these wavelength shifts cannot be explained by radiation effects on fused silica glass. These shifts are hypothesized to be caused by the conversion of the polymeric fiber coating to a glassy carbon via radiolysis and/or pyrolysis and subsequent radiation-induced compaction. Here, thermal degradation of these polymeric coatings was studied to provide insight into the potential origins of the sensor drift phenomenon. Acrylate- and polyimide-coated fibers were heated under various temperatures (250–1300 °C) and environments (oxidative and inert), and the resulting coating products were characterized via mass-loss data, scanning electron microscope imaging, and Raman spectroscopy. Results suggest that the polymer decomposition product of both coating types, at least under inert conditions, is indeed a glassy carbon. Analytical models that account for radiation-induced glassy carbon coating compaction show significant compressive fiber strains and predicted wavelength shifts that agree well with experimental measurements, providing additional evidence that supports the hypothesized origins of the sensor drift.

36 MATERIALS SCIENCE↗