Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Project Profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

LANSCE harp upgrade: analysis, design, fabrication and installation

The primary goal of this newly installed beam profile measurement is to provide the facility operators and physicists with a reliable horizontal and vertical projected beam distribution and location with respect to the proton beam target and beam aperture. During a 3000-hour annual run cycle, 5 {mu}C of charge is delivered every 50 milliseconds through this harp to the downstream TRMS Mark III target. The resulting radioactive annual dose near this harp is at least 6 MGy. Because of this harsh environment, the new harp design has been further optimized for robustness. For example, compared to an earlier design, this harp has half of the sensing wires and utilizes only a single bias plane. The sensing fibers are 0.079-mm diameter SiC fibers. To hold these fibers to a rigid ceramic structure, a collet fiber-clamping device accomplishes the three goals of maintaining a mechanical fiber clamp, holding the sense fibers under a slight tensile force, and providing a sense-fiber electrical connection. This paper describes the harp analysis and design, and provides fabrication, assembly, and some installation information, and discusses wiring alterations.

43 PARTICLE ACCELERATORS↗

SU-E-I-20: Dead Time Count Loss Compensation in SPECT/CT: Projection Versus Global Correction

Purpose: To compare projection-based versus global correction that compensate for deadtime count loss in SPECT/CT images. Methods: SPECT/CT images of an IEC phantom (2.3GBq 99mTc) with ∼10% deadtime loss containing the 37mm (uptake 3), 28 and 22mm (uptake 6) spheres were acquired using a 2 detector SPECT/CT system with 64 projections/detector and 15 s/projection. The deadtime, Ti and the true count rate, Ni at each projection, i was calculated using the monitor-source method. Deadtime corrected SPECT were reconstructed twice: (1) with projections that were individually-corrected for deadtime-losses; and (2) with original projections with losses and then correcting the reconstructed SPECT images using a scaling factor equal to the inverse of the average fractional loss for 5 projections/detector. For both cases, the SPECT images were reconstructed using OSEM with attenuation and scatter corrections. The two SPECT datasets were assessed by comparing line profiles in xyplane and z-axis, evaluating the count recoveries, and comparing ROI statistics. Higher deadtime losses (up to 50%) were also simulated to the individually corrected projections by multiplying each projection i by exp(-a*Ni*Ti), where a is a scalar. Additionally, deadtime corrections in phantoms with different geometries and deadtime losses were also explored. The same two correction methods were carried for all these data sets. Results: Averaging the deadtime losses in 5 projections/detector suffices to recover >99% of the loss counts in most clinical cases. The line profiles (xyplane and z-axis) and the statistics in the ROIs drawn in the SPECT images corrected using both methods showed agreement within the statistical noise. The count-loss recoveries in the two methods also agree within >99%. Conclusion: The projection-based and the global correction yield visually indistinguishable SPECT images. The global correction based on sparse sampling of projections losses allows for accurate SPECT deadtime loss correction while keeping the study duration reasonable.

60 APPLIED LIFE SCIENCES↗

SU-E-I-21: Deformation Mapping and Shape Prediction with 3D Tumor Volume Morphing

Purpose: To compare projection-based versus global correction that compensate for deadtime count loss in SPECT/CT images. Methods: SPECT/CT images of an IEC phantom (2.3GBq 99mTc) with ∼10% deadtime loss containing the 37mm (uptake 3), 28 and 22mm (uptake 6) spheres were acquired using a 2 detector SPECT/CT system with 64 projections/detector and 15 s/projection. The deadtime, Ti and the true count rate, Ni at each projection, i was calculated using the monitor-source method. Deadtime corrected SPECT were reconstructed twice: (1) with projections that were individually-corrected for deadtime-losses; and (2) with original projections with losses and then correcting the reconstructed SPECT images using a scaling factor equal to the inverse of the average fractional loss for 5 projections/detector. For both cases, the SPECT images were reconstructed using OSEM with attenuation and scatter corrections. The two SPECT datasets were assessed by comparing line profiles in xyplane and z-axis, evaluating the count recoveries, and comparing ROI statistics. Higher deadtime losses (up to 50%) were also simulated to the individually corrected projections by multiplying each projection i by exp(-a*Ni*Ti), where a is a scalar. Additionally, deadtime corrections in phantoms with different geometries and deadtime losses were also explored. The same two correction methods were carried for all these data sets. Results: Averaging the deadtime losses in 5 projections/detector suffices to recover >99% of the loss counts in most clinical cases. The line profiles (xyplane and z-axis) and the statistics in the ROIs drawn in the SPECT images corrected using both methods showed agreement within the statistical noise. The count-loss recoveries in the two methods also agree within >99%. Conclusion: The projection-based and the global correction yield visually indistinguishable SPECT images. The global correction based on sparse sampling of projections losses allows for accurate SPECT deadtime loss correction while keeping the study duration reasonable.

60 APPLIED LIFE SCIENCES↗

Project HyBuJET

A conceptual Hypersonic Business Jet (HyBuJet) was examined. The main areas of concentration include: aerodynamics, propulsion, stability and control, mission profile, and atmospheric heating. In order to optimize for cruise conditions, a waverider configuration was chosen for the high lift drag ratio and low wave drag. The leading edge and lower surface of a waverider was mapped out from a known flow field and optimized for cruising at Mach 6 and at high altitudes. The shockwave generated by a waverider remains attached along the entire leading edge, allowing for a larger compression along the lower surface. Three turbofan ramjets were chosen as the propulsion of the aircraft due to the combination of good subsonic performance along with high speed propulsive capabilities. A combination of liquid silicon convective cooling for the leading edges with a highly radiative outer skin material was chosen to reduce the atmospheric heating to acceptable level.

Ramsay, Tom↗

The Winter 2010 and 2011 FRONT/NIRSS In-Flight Icing Hazard Detection Project

The NASA Icing Remote Sensing System (NIRSS) deploys a vertically-pointing K-band radar, a lidar ceiliometer, and a profiling microwave radiometer to obtain measurements for diagnosing local inflight icing conditions. RAL is working with NASA GRC to develop algorithms and data ingest and display software for the system. NASA has an ongoing activity to develop remote sensing technologies for the detection and measurement of icing conditions aloft. As part of that effort NASA teamed with NCAR to develop software that fuses data from multiple instruments into a single detected icing condition product. The multiple instrument approach, which is the current emphasis of this activity, utilizes a K-band vertical staring radar, a microwave radiometer that detects twelve frequencies between 22 and 59 GHz, and a lidar ceilometer. The radar data determine cloud boundaries, the radiometer determines the sub-freezing temperature heights and total liquid water content, and the ceilometer refines the lower cloud boundary. Data is post-processed in C++ program with a Java-based web display of resultant supercooled LWC profile and aircraft hazard identification. In 2010, a multi-channel scanning radiometer, designed and built by Radiometrics, Inc. under a SBIR grant,,was added to the system to assess its utility in improving icing diagnoses.

Serke, David↗

Observational needs for estimating Alaskan soil carbon stocks under current and future climate

Abstract Representing land surface spatial heterogeneity when designing observation networks is a critical scientific challenge. Here we present a geospatial approach that utilizes the multivariate spatial heterogeneity of soil‐forming factors—namely, climate, topography, land cover types, and surficial geology—to identify observation sites to improve soil organic carbon (SOC) stock estimates across the State of Alaska, USA. Standard deviations in existing SOC samples indicated that 657, 870, and 906 randomly distributed pedons would be required to quantify the average SOC stocks for 0–1 m, 0–2 m, and whole‐profile depths, respectively, at a confidence interval of 5 kg C m −2 . Using the spatial correlation range of existing SOC samples, we identified that 309, 446, and 484 new observation sites are needed to estimate current SOC stocks to 1 m, 2 m, and whole‐profile depths, respectively. We also investigated whether the identified sites might change under future climate by using eight decadal (2020–2099) projections of precipitation, temperature, and length of growing season for three representative concentration pathway (RCP 4.5, 6.0, and 8.5) scenarios of the Intergovernmental Panel on Climate Change. These analyses determined that 12 to 41 additional sites (906 + 12 to 41; depending upon the emission scenarios) would be needed to capture the impact of future climate on Alaskan whole‐profile SOC stocks by 2100. The identified observation sites represent spatially distributed locations across Alaska that captures the multivariate heterogeneity of soil‐forming factors under current and future climatic conditions. This information is needed for designing monitoring networks and benchmarking of Earth system model results.

54 ENVIRONMENTAL SCIENCES↗

Gaseous cometary coronal

Ground-based observations of coma emission line profiles permit direct insight into the composition and kinetic state of a cometary atmosphere and in turn provide much needed constraints in reconstructing a comet's history; the profiles themselves yield information on the mechanisms generating the observed species, while their intensities correspond to overall production rates by the nucleus. Intensities and line profiles at wavelength 6562.1A (H-alpha) and 6300.3A (O(1D) deday) were obtained for Comet Halley in the period March - April 1986 and for Comet Wilson in the period March 1987 using the Fabry-Perot optical facility at Arecibo; the Comet Halley observations have been undergoing careful analysis as the main effort of this project. Attention was centered on O(1D) 6300A observations obtained over four consecutive nights in April 1986. Surprisingly, the sorts of profiles to be expected in coma observations have not been theoretically developed in the past, necessitating a reappraisal of this question. It turns out that coma profiles vary noticeably according to excitation mechanism, and the proper interpretation of a profile requires the use of the appropriate model type. A paper cataloging the basic types and their interpretation will be submitted for publication in a few months. The intensities of the 6300A emission can be used independently to estimate the production rate of H2O by the comet nucleus; indeed, this may be the most reliable way of determining this basic quantity using ground-based facilities. The H2O production rates implied by our observations throughout the period March-April 1986 have been derived and are to be presented at the upcoming COSPAR special session Aeronomy of Comets and Outer Planets.

Atreya, Sushil K.↗

Implantation of sodium ions into germanium

The donor properties of Na atoms introduced by ion implantation into p-Ge with the resistivity 20-40 {Omega} cm are established for the first time. Na profiles implanted into Ge (the energies 70 and 77 keV and the doses (0.8, 3, 30) Multiplication-Sign 10{sup 14} cm{sup -2}) are studied. The doses and annealing temperatures at which the thermoprobe detects n-type conductivity on the sample surface are established. After implantation, the profiles exhibit an extended tail. The depth of the concentration maximum is in good agreement with the calculated mean projected range of Na ions R{sub p}. Annealing for 30 min at temperatures of 250-700 Degree-Sign C brings about a redistribution of Na atoms with the formation of segregation peaks at a depth, which is dependent on the ion dose, and is accompanied by the diffusion of Na atoms to the surface with subsequent evaporation. After annealing at 700 Degree-Sign C less than 7% of the implanted ions remain in the matrix. The shape of the profile tail portions measured after annealing at temperatures 300-400 Degree-Sign C is indicative of the diffusion of a small fraction of Na atoms into the depth of the sample.

36 MATERIALS SCIENCE↗

DOE's 449 MHz Wind Profiling Radars on the U.S. West Coast: Annual Report for Fiscal Year 2016

The three coastal wind profilers and associated meteorological instruments located in Forks, WA, Astoria, OR, and North Bend, OR, provide important observations at high temporal and vertical spatial resolution to characterize the meteorological inflow to the western region of the United States. These instruments have been operating for a year or more, and furnish boundary conditions for the modeling efforts of the WFIP2 project. The data have been delivered to archives at both NOAA and the DOE A2e DAP at a data recovery rate in excess of 98%. Site maintenance activities have been relatively minor, with a few component replacements and repairs to RASS foam. Bird mortality surveys have found no bird nests or carcasses, and the U.S. Fish and Wildlife Service has regularly been provided survey reports. This project represents a successful collaboration between PNNL and NOAA to procure, test, deploy, maintain, and operate three 449 MHz radar wind profilers.

54 ENVIRONMENTAL SCIENCES↗

Data for Post-Access Report: Tidal Energy Resource Characterization and Model Validation via the Assessment of Cost-effective Spatially Distributed Current Measurements from microFloat Swarms

This project evaluated how high-resolution, spatially distributed field data can be used to refine and validate site-scale hydrodynamic simulations of tidal channels. Use of such spatially-distributed field observations or site-scale hydrodynamic simulations will be needed for producing accurate predictions of tidal energy production over larger arrays of tidal turbines. The data contained in this archive includes field observations of water velocity from a series of short surveys in Agate Pass taken on August 20th, 2020 using station-keeping ADCP (acoustic doppler current profiler) measurements, drifting downward-looking ADCPs, and microFloats, gathered by researchers at APL-UW under a previous project. It also includes high-resolution hydrodynamic model runs for the site during that time generated under TEAMER support. An explanatory file (.pdf format) describes the survey and field data structure. Processed data is stored in .mat format. Survey summary: start time, number of floats, water level. microFloat data: - Cleaned data for each float in survey, - Time series of position (lat., lon.), depth (relative to surface), and horizontal velocity (u, v) Drifting ADCP data: - Cleaned data for each drifting ADCP in survey - Time series of position (lat., lon.), sample depth (relative to surface), and observed water velocity (u,v,w) Stationary ADCP data: - Cleaned data for each station-keeping data set in survey - Time series of position (lat., lon.), sample depth (relative to surface), and observed water velocity (u,v,w) FVCOM (Finite Volume Coastal Ocean Model) model outputs: Water level and velocity, as well as derived variables (e.g., power density) from the final refined model simulations for the Agate Pass subdomain. Contained in NetCDF and ASCII files for the duration of August 18th and 20th 2020 field surveys. Additional scripts for processing the data and generating the figures in the report are included.

16 TIDAL AND WAVE POWER↗

Fuel Cell Powered Lift Truck

This project, entitled “Recovery Act: Fuel Cell-Powered Lift Truck Sysco (Houston) Fleet Deployment”, was in response to DOE funding opportunity announcement DE-PS36-08GO98009, Topic 7B, which promotes the deployment of fuel cell powered material handling equipment in large, multi-shift distribution centers. This project promoted large-volume commercialdeployments and helped to create a market pull for material handling equipment (MHE) powered fuel cell systems. Specific outcomes and benefits involved the proliferation of fuel cell systems in 5-to 20-kW lift trucks at a high-profile, real-world site that demonstrated the benefits of fuel cell technology and served as a focal point for other nascent customers. The project allowed for the creation of expertise in providing service and support for MHE fuel cell powered systems, growth of existing product manufacturing expertise, and promoted existing fuel cell system and component companies. The project also stimulated other MHE fleet conversions helping to speed the adoption of fuel cell systems and hydrogen fueling technology. This document also contains the lessons learned during the project in order to communicate the successes and difficulties experienced, which could potentially assist others planning similar projects.

30 DIRECT ENERGY CONVERSION↗

The adult literacy evaluator: An intelligent computer-aided training system for diagnosing adult illiterates

An important part of NASA's mission involves the secondary application of its technologies in the public and private sectors. One current application being developed is The Adult Literacy Evaluator, a simulation-based diagnostic tool designed to assess the operant literacy abilities of adults having difficulties in learning to read and write. Using ICAT system technology in addition to speech recognition, closed-captioned television (CCTV), live video and other state-of-the art graphics and storage capabilities, this project attempts to overcome the negative effects of adult literacy assessment by allowing the client to interact with an intelligent computer system which simulates real-life literacy activities and materials and which measures literacy performance in the actual context of its use. The specific objectives of the project are as follows: (1) To develop a simulation-based diagnostic tool to assess adults' prior knowledge about reading and writing processes in actual contexts of application; (2) to provide a profile of readers' strengths and weaknesses; and (3) to suggest instructional strategies and materials which can be used as a beginning point for remediation. In the first and developmental phase of the project, descriptions of literacy events and environments are being written and functional literacy documents analyzed for their components. Examples of literacy events and situations being considered included interactions with environmental print (e.g., billboards, street signs, commercial marquees, storefront logos, etc.), functional literacy materials (e.g., newspapers, magazines, telephone books, bills, receipts, etc.) and employment related communication (i.e., job descriptions, application forms, technical manuals, memorandums, newsletters, etc.). Each of these situations and materials is being analyzed for its literacy requirements in terms of written display (i.e., knowledge of printed forms and conventions), meaning demands (i.e., comprehension and word knowledge) and social situation. From these descriptions, scripts are being generated which define the interaction between the student, an on-screen guide and the simulated literacy environment. The proposed outcome of the Evaluator is a diagnostic profile which will present broad classifications of literacy behaviors across the major areas of metacognitive abilities, word recognition, vocabulary knowledge, comprehension and writing. From these classifications, suggestions for materials and strategies for instruction with which to begin corrective action will be made. The focus of the Literacy Evaluator will be essentially to provide an expert diagnosis and an interpretation of that assessment which then can be used by a human tutor to further design and individualize a remedial program as needed through the use of an authoring system.

Yaden, David B., Jr.↗

The megasecond Chandra X-ray visionary project observation of NGC 3115: Witnessing the flow of hot gas within the Bondi radius

Observational confirmation of hot accretion model predictions has been hindered by the challenge to resolve spatially the Bondi radii of black holes with X-ray telescopes. Here, we use the Megasecond Chandra X-ray Visionary Project observation of the NGC 3115 supermassive black hole to place the first direct observational constraints on the spatially and spectroscopically resolved structures of the X-ray emitting gas inside the Bondi radius of a black hole. We measured temperature and density profiles of the hot gas from a fraction out to tens of the Bondi radius (R{sub B} = 2.''4-4.''8 = 112-224 pc). The projected temperature jumps significantly from ∼0.3 keV beyond 5'' to ∼0.7 keV within ∼4''-5'', but then abruptly drops back to ∼0.3 keV within ∼3''. This is contrary to the expectation that the temperature should rise toward the center for a radiatively inefficient accretion flow. A hotter thermal component of ∼1 keV inside 3'' (∼150 pc) is revealed using a two-component thermal model, with the cooler ∼0.3 keV thermal component dominating the spectra. We argue that the softer emission comes from diffuse gas physically located within ∼150 pc of the black hole. The density profile is broadly consistent with ρ∝r {sup –1} within the Bondi radius for either the single temperature or the two-temperature model. The X-ray data alone with physical reasoning argue against the absence of a black hole, supporting that we are witnessing the onset of the gravitational influence of the supermassive black hole.

79 ASTRONOMY AND ASTROPHYSICS↗

ROTATION OF THE K3 II-III GIANT STAR {alpha} HYDRA

Fundamental spectroscopic determination of projected rotation rates of slowly rotating stars is challenging because the rotational broadening of the spectral lines is often comparable to, or smaller than, the broadening from other sources, most notably macroturbulence. Fourier techniques have the advantage over direct profile matching when the observed profiles are complete, but when the profiles are severely blended, the Fourier analysis is compromised. A process of modeling partial profiles for determining the rotation rate for stars having blended spectral lines is investigated and applied to the evolved star {alpha} Hya (K3 II-III). Projected rotation higher than 5 km s{sup -1} can be definitively ruled out for this star. Not all lines are equally good, depending on the amount of blending and also depending on the strength of the line, as the balance between the thermal and non-thermal components changes. A modest ambiguity arises between macroturbulence and rotational broadening, but a careful look at the differences between the observations and the models allows one to measure the rotation with acceptable precision. The result for {alpha} Hya is v sin i = 2.6 {+-} 0.3 km s{sup -1}.

79 ASTRONOMY AND ASTROPHYSICS↗

Elevated aerosol layers modify the O2–O2 absorption measured by ground-based MAX-DOAS

The oxygen collisional complex (O2-O2, or O4) is a greenhouse gas, and a calibration trace gas used to infer aerosol and cloud properties by Differential Optical Absorption Spectroscopy (DOAS). Recent reports suggest the need for an O4 correction factor (CFO4) when comparing simulated and measured O4 differential slant column densities (dSCD) by passive DOAS. We investigate the sensitivity of O4 dSCD simulations at ultraviolet (360 nm) and visible (477 nm) wavelengths towards separately measured aerosol extinction profiles. Measurements were conducted by the University of Colorado 2D-MAX-DOAS instrument and NASA’s multispectral High Spectral Resolution Lidar (HSRL-2) during the Two Column Aerosol Project (TCAP) at Cape Cod, MA in July 2012. During two case study days with (1) high aerosol load (17 July, AOD ~ 0.35 at 477 nm), and (2) near molecular scattering conditions (22 July, AOD < 0.10 at 477 nm) the measured and calculated O4 dSCDs agreed within 6.4±0.4% (360 nm) and 4.7±0.6% (477 nm) if the HSRL-2 profiles were used as input to the calculations. However, if in the calculations the aerosol is confined to the surface layer (while keeping AOD constant) we find 0.53<CFO4<0.75, similar to previously reported CFO4. Our results suggest that elevated aerosol layers, unless accounted for, can cause negative bias in the simulated O4 dSCDs that can explain CFO4. The air density and aerosol profile aloft needs to be taken into account when interpreting the O4 from ground-based MAX-DOAS. Opportunities to identify and better characterize these layers are also discussed.

54 ENVIRONMENTAL SCIENCES↗

Current state and future projections of drying processes in the US food and pulp and paper sectors: Energy, economic, and environmental assessment

The pulp and paper (P/P) and food sectors are the third- and fifth-largest industrial energy consumers in the United States, with total on-site energy consumption of 2,039 TBtu and 1,144 TBtu, respectively. Thermal drying processes for moisture removal, which are energy-intensive, play a critical role in both industries. This study is the first to evaluate state- and national-level US drying energy demand for these sectors from 2020 to 2050. To complete this evaluation, we developed a thermodynamic modeling framework integrated with economic and environmental models to compute product-specific drying energy intensity and estimate the sector-specific costs and emissions profiles associated with drying operations. The model-predicted energy intensity was validated against the literature. Using current and projected annual production volumes in these sectors, we estimated total drying energy use. Results indicate that drying accounts for 22 % of total energy consumption in the P/P sector and 10 % in the food sector. The estimated annual energy cost (2020) to operate thermal dryers is $\$$919 M in the P/P sector and $\$$417 M in the food sector. Additionally, drying contributes to 25 % of total CO 2 e emissions in the P/P sector (including biogenic) and 15 % of emissions in the food sector. Regional performance shows that the Southern US is the leading energy consumer for P/P drying, whereas the Midwest leads in food drying. This study presents both potential solutions to enhance drying efficiency and barriers to implementation. Energy efficiency improvements, low-carbon fuels, and electrification are discussed as key pathways for reducing costs and optimizing industrial drying processes.

3E analysis↗

Experiment and Modeling of ITER Demonstration Discharges in the DIII-D Tokamak

DIII-D is providing experimental evaluation of 4 leading ITER operational scenarios: the baseline scenario in ELMing H-mode, the advanced inductive scenario, the hybrid scenario, and the steady state scenario. The anticipated ITER shape, aspect ratio and value of I/{alpha}B were reproduced, with the size reduced by a factor of 3.7, while matching key performance targets for {beta}{sub N} and H{sub 98}. Since 2008, substantial experimental progress was made to improve the match to other expected ITER parameters for the baseline scenario. A lower density baseline discharge was developed with improved stationarity and density control to match the expected ITER edge pedestal collisionality ({nu}*{sub e} {approx} 0.1). Target values for {beta}{sub N} and H{sub 98} were maintained at lower collisionality (lower density) operation without loss in fusion performance but with significant change in ELM characteristics. The effects of lower plasma rotation were investigated by adding counter-neutral beam power, resulting in only a modest reduction in confinement. Robust preemptive stabilization of 2/1 NTMs was demonstrated for the first time using ECCD under ITER-like conditions. Data from these experiments were used extensively to test and develop theory and modeling for realistic ITER projection and for further development of its optimum scenarios in DIII-D. Theory-based modeling of core transport (TGLF) with an edge pedestal boundary condition provided by the EPED1 model reproduces T{sub e} and T{sub i} profiles reasonably well for the 4 ITER scenarios developed in DIII-D. Modeling of the baseline scenario for low and high rotation discharges indicates that a modest performance increase of {approx} 15% is needed to compensate for the expected lower rotation of ITER. Modeling of the steady-state scenario reproduces a strong dependence of confinement, stability, and noninductive fraction (f{sub NI}) on q{sub 95}, as found in the experimental I{sub p} scan, indicating that optimization of the q profile is critical to simultaneously achieving the f{sub NI} = 1 and Q = 5 goals. Extended integrated modeling is being developed to improve capability for ITER projection by including the experimental observations of density peaking, ELM characteristics, NTM suppression and coupled core-edge-SOL transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗