Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Longtime Durability of PMR-15 Matrix Polymer at 204, 260, 288, and 316 C

Isothermal weight loss studies at the Glenn (Lewis) Research Center were conducted at four temperatures (204, 260, 288, and 316 C) with specimens of varied geometric shapes to investigate the mechanisms involved in the thermal degradation of PMR-15. Both neat resin behavior and composite behaviors were studied. Two points of interest in these studies are the role(s) of oxygen in the mechanisms involved in the thermo-oxidative degradation of these composite materials and the dimensional changes that occur during their useable lifetime. Specimen dimensional changes and surface layer growth were measured and recorded. It was shown that physical and chemical changes take place as a function of time and location in PMR-15 neat resin and composites as aging takes place in air at elevated temperatures. These changes initiate at the outer surfaces of both materials and progress inward following the oxygen as it proceeds by diffusion into the central core of each material. Microstructural changes cause changes in density, material shrinkage (strains), glass transition temperature, dimension, dynamic shear modulus, and compression properties. These changes also occur slowly dividing the polymer material into two distinct parts: a visibly undamaged core section between two visibly damaged surface layers. The surface layer has a significant effect on compression properties of thinner specimens, but the visibly undamaged core material controls these properties for specimens having eight or more plies. It was demonstrated that there are three different mechanisms involved in the degradation of PMR-15 during aging at elevated temperatures. These are a weight gain, a small weight fraction bulk material weight loss, and a large mass fraction weight loss concentrated at the surface of the polymer or composite. At the higher temperatures (260 C and above), the surface loss predominates. Below 260 C, the surface loss and the bulk core loss become more equivalent. Between 175 and 260 C, the initial weight change is due to a weight gain mechanism with a visible lifetime that diminishes as the aging temperature increases.

Bowles, Kenneth J.↗
DOE OSTI2020

Addition of Short Polymer Chains Mechanically Reinforces Glassy Poly(2-vinylpyridine)–Silica Nanoparticle Nanocomposites

The addition of hard fillers to a polymer matrix is a well-known process for achieving mechanical reinforcement. With a decrease in the size of the fillers, the contribution from polymer–particle nanometer-sized interfaces become significant, and these interfaces affect the mechanical performance of polymer nanocomposites (PNCs) beyond the limits established for conventional composites. However, the molecular mechanisms underlying the improvement in the mechanical performance of glassy PNCs remain unresolved, necessitating a deeper understanding of the structure–property relationships in these intrinsically heterogeneous systems. In this effort, by using Brillouin light scattering (BLS) and dynamic mechanical analysis (DMA), we demonstrated that adding shorter chains to a PNC prepared with high molecular weight polymers significantly improved the mechanical properties of the PNC in the glassy state. The strongest enhancement of mechanical properties occurred at an optimum concentration of short chains. This is in contrast to behavior of the glass transition temperature of PNCs which shows a monotonic decrease with an increase in the concentration of shorter chains. Using experimental data and coarse-grained molecular dynamics (MD) simulations, we have identified the molecular mechanism leading to the observed non-monotonic changes in mechanical reinforcement. Here, this mechanism includes changes in the nanoscale organization at the interface, combined with chain stretching amplified by the addition of the short chains. Overall, our approach paves a simple, cost-effective pathway to fabricating glassy PNCs with significantly improved mechanical properties that will fill various practical needs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Stimulus-Responsive Modulation of Solvation Environments in Solid Catalysts

Liquid environments play a crucial role in the biological processes occurring in living organisms as well as in many human-made processes involving electrochemistry, photo-, and thermocatalysis. In the majority of these systems, aqueous phases are ubiquitous due to water’s natural abundance. Water molecules, however, can exert large changes in the chemical environment of catalytically active sites, altering the reaction rates, selectivity, and catalyst stability. These solvation effects induced by water molecules near catalytic sites can drastically change the energy landscape and unlock unique reaction pathways with far more favorable kinetics. In nature, living organisms couple these complex interactions with detection, communication, and actuation mechanisms to induce self-regulatory behavior, ensuring stability of the system and thus long-term durability. Extrapolating this behavior to heterogeneous catalysis is desirable because the resulting “smart materials” can potentially unlock new chemical conversion processes with higher atom efficiency, rates, and stability. The combination of polymer chemistry and heterogeneous catalysis has introduced versatile approaches for creating materials that can respond to cues in the reaction medium that alter the accessibility, intrinsic activity, and selectivity of the catalyst. To achieve this, one could combine stimulus-responsive polymers, which undergo a large volumetric phase transition in response to an external stimulus, with a solid catalyst. This chemo-mechanical response has been employed to create a variety of nanoreactor vessels with stimulus-responsive character that turn on- and off- depending on the reaction conditions. In this Account, we focus on the impact of these polymer coatings on the solvation environment around the active site and the implications of these effects on the reaction energy landscape, molecular arrangement of the solvent, electric fields at the catalyst–liquid interface, binding energy, and mobility of surface reaction intermediates. These seemingly subtle changes in solvent molecules induced by the presence of polymers can have a tremendous impact on the development of bioinspired heterogeneous catalysts, reliable chemical clocks, micro/nanoreactors, and robots. The large library of polymer chemistries offers a plethora of combinations of stimulus-responsive mechanisms (e.g., temperature, pH, light, magnetic field, solvent composition), providing the possibility of creating homeostatic catalysts à la carte.

catalysts↗
DOE OSTI2024

Liquid state theory of the structure of model polymerized ionic liquids

We employ polymer integral equation theory to study a simplified model of semiflexible polymerized ionic liquids (PolyILs) that interact via hard core repulsions and short range screened Coulomb interactions. The multi-scale structure in real and Fourier space of PolyILs (ions chosen to mimic Li, Na, K, Br, PF 6 , and TFSI) are determined as a function of melt density, Coulomb interaction strength, and ion size. Comparisons with a homopolymer melt, a neutral polymer–solvent-like athermal mixture, and an atomic ionic liquid are carried out to elucidate the distinct manner that ions mediate changes of polymer packing, the role of excluded volume effects, and the influence of chain connectivity, respectively. The effect of Coulomb strength depends in a rich manner on ion size and density, reflecting the interplay of steric packing, ion adsorption, and charge layering. Ion-mediated bridging of monomers is found, which intensifies for larger ions. Intermediate range charge layering correlations are characterized by a many-body screening length that grows with PolyIL density, cooling, and Coulomb strength, in disagreement with Debye–Hückel theory, but in accord with experiments. Qualitative differences in the collective structure, including an ion-size-dependent bifurcation of the polymer structure factor peak and pair correlation function, are predicted. The monomer cage order parameter increases significantly, but its collective ion counterpart decreases, as ions become smaller. Such behaviors allow one to categorize PolyILs into two broad classes of small and large ions. Furthermore, dynamical implications of the predicted structural results are qualitatively discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

Nonequilibrium material effects on the behavior of polymeric composite matrices and their related composites

The effects of physical aging on the material properties of some linear and network macromolecular glasses are discussed. The free volume concept is used to describe this behavior. The effect of physical aging on properties of some uniaxial graphite/fiber epoxy resin composites is investigated using stress relaxation in both tensile and flexural modes. The matrix polymers used were resins both of which are based on a 4,4-methylenedianiline derivative of epichlorohydrin with diamino diphenyl sulfone (DDS) as the curing agent. The matrix resin, as used in the practical application in composites, not fully cured and the glass transition of the network was dependent on the curing schedule. The physical aging of the bulk crosslinked epoxy was found to depend on the annealing temperature, and the T sub g of the resin. The physical aging of the composite, monitored by the stress relaxation method, was found to be dependent on the testing direction.

Wilkes, G. L.↗
NASA NTRS2003

Gravitational Effects on Distortion in Sintering

During sintering a powder compact gains strength through low-temperature interparticle bonding, usually induced by solid-state surface diffusion, followed by further strength contributions from high-temperature densification. In cases where a liquid phase forms, sintering densification is accelerated and shape retention is sustained while open pores remain and contribute capillary forces. Unfortunately, sintering densification requires the compact become thermally softened to a point where creep strain rates reach levels near 10(exp -2)/s when the liquid forms. On the other hand, thermal softening of the powder compact substantially reduces the strength at high temperatures. Therefore, the in situ strength evolution during sintering is a primary focus to separate compact densification (as required for high performance) with minimized distortion (as required for net-shaping). With respect to gravitation effects on distortion during sintering there are two points of substantial weakness - prior to significant interparticle bonding and during final pore closure. This research is focused on understanding the competition among interparticle neck growth, densification, thermal softening, grain boundary wetting, capillary effects associated with liquid wetting and residual porosity, and gravity. Most surprising is the apparent role of gravity, where the deviatoric stress acting on the powder structure induces skeletal formation that reduces distortion. In contrast with theory, microgravity samples exhibit more distortion yet fail to fully densify. Results are presented on the experimental concepts supporting an emerging model of sintering strength evolution that enables understanding of both distortion and densification. The experiments have relied on tungsten heavy alloys, various combinations of dihedral angle, pore size, initial porosity, liquid:solid ratio, and heating rates. On Earth, the dominant factor with respect to distortion is the starting body heterogeneity. Current modeling efforts are seeking some means to uniformly predict the distortion based on a starting pore structure heterogeneity parameter. Densification is largely unaffected by the initial pore structure, but distortion is highly variable, suggesting that nonuniform pore closure might be a significant parameter during sintering. With respect to flight experiments, plans include removal of the solid body forces acting on the solid grains, allowing stabilization of the pore structure and examination of the buoyancy effects with regard to distortion. In microgravity there is the surprising result that compacts do not densify, yet distort a factor that is contrary to all current sintering models. Densification without distortion during liquid phase sintering was achieved by manipulating microstructure and its evolution during sintering. Microstructure parameters such as the solid volume fraction, dihedral angle, initial porosity, and pore size were varied to measure densification and distortion behavior during LPS using W-Ni-Cu alloys. Green compacts were formed using ethylene-bis-stearamide as a pore-forming agent with the amount of polymer controlling the initial porosity. Different initial pore sizes were generated by varying the polymer particle size. Dihedral angle was varied by changing the Ni:Cu ratio in the alloys. Finally, the solid volume fraction was adjusted via the tungsten content. Distortion was quantified using profiles determined with a coordinate measuring machine to calculate a distortion parameter. Sintering results showed that solid volume fraction and dihedral angle are the dominant factors on densification and distortion during liquid phase sintering. Distortion decreases with increasing solid volume fraction and dihedral angle, while initial porosity and pore size have no observable effect on distortion at nearly full densification. Various strategies emerge to improve distortion control in liquid phase sintering.

German, Randall M.↗
DOE OSTI2022

An Integrated Theoretical and Experimental Approach to Achieve Highly Polarizable Relaxor Ferroelectric Liquid Crystalline Polymers

In this project, we have designed and synthesized a series of aliphatic sulfonlyated chiral and achiral polyether. The major objective is to achieve ferroelectric liquid crystalline polymers with a high spontaneous polarization (0.04-0.08 C/m2). Due to the strong dipole-dipole interaction among the sulfonyl side groups, which resembles that among water molecules, these polyethers can exhibit various liquid crystalline self-assemblies without any rigid mesogens. By tuning the position of the sulfonyl groups, single versus double sulfonyl groups, and spacer/tail length and methyl branches, the liquid crystalline phases include smectic A, smectic C, and hexagonal columnar phases. When the single sulfonyl group is next to the main chain or disulfonyl groups are separated by a short C3 spacer, the dipolar interaction is too strong to allow any dipole switching. As a result, the linear dielectric behavior is observed with a low dielectric constant of 5-7. When the single sulfonyl groups are away from the main chain, the paraelectric behavior is obtained with a high dielectric constant around 20. From this study, we predict that by further tailoring the intermolecular interactions among the disulfonyl side groups, it is possible to achieve ferroelectric property for these liquid crystalline polymers. If successful, these ferroelectric liquid crystalline polymers can be used for efficient electrocaloric cooling applications.

36 MATERIALS SCIENCE↗
NASA NTRS2013

Stress-Dependent Voltage Offsets From Polymer Insulators Used in Rock Mechanics and Material Testing

Dielectric insulators are used in a variety of laboratory settings when performing experiments in rock mechanics, petrology, and electromagnetic studies of rocks in the fields of geophysics,material science, and civil engineering. These components may be used to electrically isolate geological samples from the experimental equipment, to perform a mechanical compliance function between brittle samples and the loading equipment, to match ultrasonic transducers, or perform other functions. In manyexperimental configurations the insulators bear the full brunt of force applied to the sample but do not need to withstand high voltages, therefore the insulators are often thin sheets of mechanically tough polymers. From an instrument perspective, transduction from various types of mechanical perturbation has beenqualitatively compared for a number of polymers [1, 2] and these error sources are readily apparent duringhigh-impedance measurements if not mitigated. However even when following best practices, a force dependent voltage signal still remains and its behavior is explored in this presentation. In this experimenttwo thin sheets (0.25 mm) of high-density polyethylene (HDPE) were set up in a stack, held alternatelybetween three aluminum bars; this stack was placed on the platen of a 60T capacity hydraulic testingmachine. The surface area, A, over which the force is applied to the PE sheets in this sandwich is roughly 40 square cm, each sheet forming a parallel-plate capacitor having roughly 320 pF [3], assuming therelative dielectric permittivity of PE is approximately 2.3. The outer two aluminum bars were connected to the LO input ofthe electrometer and the central aluminum bar was connected to the HI input of a Keithley model 617 electrometer. Once the stack is mechanically well-seated with no air gaps, the voltage offset is observed tobe a linear function of the baseline voltage for a given change in applied force. For a periodically appliedforce of 66.7 kN the voltage offsets were measured as a function of initial voltage, and these data were fitwith a linear function that was constrained to pass through the origin. The best fit solution had a correlation coefficient of R=0.85 and a slope of approximately -0.0228 volts/volt. The voltage offset when normalizedis demonstrated to be constant -2.28% for both positive and negative polarities over nearly 3 orders ofbaseline voltage magnitude. From this, the voltage-force coefficient is derived to be -0.34 ppm/N. Thiscorrelates well to a first-order parallel plate capacitor model that assumes constant area, and smalldeformation such that the polymer may be mechanically modeled by a spring that obeys Hookes law. Thissimple model predicts that the coefficient of proportionality is a function of Youngs modulus E= 0.8 GPaand surface area of the insulator, theoretically -1EA= -0.31 ppm/N. The outcome of this work is animproved insulator made from ultra-high molecular weight (UHMW) polyethylene and other approachestoward the minimization of and compensation for these experimental artifacts.

Electromagnetic Studies of Rocks↗
DOE OSTI2022

Particle anisotropy tunes emergent behavior in active colloidal systems

Studies of active particle systems have demonstrated that particle anisotropy can impact the collective behavior of a system, motivating a systematic study. Here, we report a systematic computational investigation of the role of anisotropy in shape and active force director on the collective behavior of a two-dimensional active colloidal system. We find that shape and force anisotropy can combine to produce critical densities both lower and higher than those of disks. Furthermore, we demonstrate that changing particle anisotropy tunes what we define as a “collision efficiency” of inter-particle collisions in leading to motility-induced phase separation (MIPS) of the system. We use this efficiency to determine the relative critical density across systems. Additionally, we observe that local structure in phase-separated clusters is the same as the particle's equilibrium densest packing, suggesting a general connection between equilibrium behavior and non-equilibrium cluster structure of self-propelled anisotropic particles. In engineering applications for active colloidal systems, shape-controlled steric interactions such as those described here may offer a simple route for tailoring emergent behaviors.

42 ENGINEERING↗
DOE OSTI2021

Effects of polymer grain boundary passivation on organic–inorganic hybrid perovskite field-effect transistors

Despite successful applications of solution-processed organic–inorganic hybrid perovskites (OIHPs) such as archetypical methylammonium lead iodide (MAPI) in high-performance optoelectronic devices including solar cells and light emitting diodes, their application in field-effect transistors (FETs) remains relatively limited due to the unresolved issues caused by ion migration in OIHPs, such as screening of gate electric fields, lowered device on-off ratios and field-effect mobility, and large hysteresis in the FET transfer characteristics. Here, we report improved performances of the MAPI-based FET via a polymer-additive-based grain boundary (GB) passivation approach that suppresses the ion migration. Polycaprolactone (PCL) was incorporated into the MAPI FET as a GB-passivation additive as confirmed by scanning electron and atomic force microscopies. Unlike the typical n-type behavior and large transfer hysteresis in the starting, pristine MAPI FETs, the GB passivation by PCL led to a drastically reduced hysteresis in FET transfer characteristics, while hinting at an ambipolar transport and slight improvement in mobility, indicating a reduced ion migration in the PCL-incorporated MAPI FET. The effect of PCL GB passivation in suppressing ion migration was directly confirmed by the measured, increased activation energy for ion migration in the PCL-incorporated MAPI. Here, the results not only represent the first report of the polymer-additive-based mitigation of the ion migration in the MAPI FET but also suggest potential utilities of the approach for enabling high-performance OIHP FETs and electronic devices in general.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

3D Printing of Liquid Crystal Elastomer Foams for Enhanced Energy Dissipation Under Mechanical Insult

Polymer foams are an essential class of lightweight materials used to protect assets against mechanical insults, such as shock and vibration. Two features are important to enhance their energy absorption characteristics: the foam structure and the matrix phase mechanical behavior. This study investigates novel approaches to control both of these features to enhance the energy absorption capability of flexible lattice foams. First, we consider 3D printing via digital light processing (DLP) as a method to control the foam mesostructure across a suite of periodic unit cells. Second, we introduce an additional energy dissipation mechanism in the solid matrix phase material by 3D printing the lattice foams with polydomain liquid crystal elastomer (LCE), which undergo a mechanically induced phase transition under large strains. This phase transition is associated with LC mesogen rotation and alignment and provides a second mechanism for mechanical energy dissipation in addition to the viscoelastic relaxation of the polymer network. Here, we contrast the 3D printed LCE lattices with conventional, thermomechanically near-equivalent elastomer lattice foams to quantify the energy-absorbing enhancement the LCE matrix phase provides. Under cyclic quasi-static uniaxial compression conditions, the LCE lattices show dramatically enhanced energy dissipation in uniaxial compression compared to the non-LCE equivalent foams printed with a commercially available photocurable elastomer resin. The lattice geometry also plays a prominent role in determining the energy dissipation ratio between the LCE and non-LCE foams. We show that when increasing the lattice connectivity, the foam deformation transitions from bending-dominated to stretching-dominated deformations, which generates higher axial strains in the struts and higher energy dissipation in the lattice foam, as stretching allows greater mesogen rotation than bending. The LCE foams demonstrate superior energy absorption during the repeated dynamic loading during drop testing compared with the non-LCE equivalent foams, demonstrating the potential of LCEs to enhance physical protection systems against mechanical impact.

3D printing↗
DOE OSTI2020

Improved Single-Ion Conductivity of Polymer Electrolyte via Accelerated Segmental Dynamics

Single-ion conducting polymer electrolytes (SICPEs) have many advantages for solid-state battery applications, while low conductivities remain the bottleneck for their practical applications. In this paper, a strategy that can significantly improve the ionic conductivity of SICPEs based on the concept of accelerated segmental dynamics was demonstrated by the evaluation of the thermal property, rheological behavior, morphology analysis, molecular dynamics simulation, and conductivity performance. With both “soft” poly(dimethylsiloxane) (PDMS) backbone and poly(ethylene glycol) (PEG) side chains, the obtained SICPE possesses faster segmental relaxation and higher lithium-ion conductivity. With lithium “transference” number close to unity, the obtained SICPE also shows excellent electrochemical stability against lithium metal electrodes. The clear relationship established between the segmental dynamics of polymer electrolyte and its ionic conductivity should contribute to achieve a solid electrolyte with improved ionic conductivity toward the next-generation solid-state battery.

Segmental Dynamics↗
NASA NTRS1986

The role of damage-softened material behavior in the fracture of composites and adhesives

Failure mechanisms of materials under very high strains experienced at and ahead of the crack tip such as formation, growth, and interaction of microvoids in ductile materials, microcracks in brittle solids or crazes in polymers and adhesives are represented by one-dimensional, nonlinear stress-strain relations possessing different ways by which the material loses capacity to carry load up to fracture or total separation. A double cantilever beam (DCB) type specimen is considered. The nonlinear material is confined to a thin strip between the two elastic beams loaded by a wedge. The problem is first modeled as a beam on a nonlinear foundation. The pertinent equation is solved numerically as a two-point boundary value problem for both the stationary and the quasi-stationay propagating crack. A finite element model is then used to model the problem in more detail in order to assess the adequacy of the beam model for the reduction of experimental data to determine in-situ properties of the thin interlayer.

Ungsuwarungsri, T.↗
DOE OSTI2022

Characterization of nonlinear ultrasonic waves behavior while interacting with poor interlayer bonds in large-scale additive manufactured materials

Over the past decades, researchers have developed several nonlinear ultrasonic techniques for quality control of materials commonly used in different applications. Owing to the superior sensitivity of nonlinear ultrasound waves to small defects such as micro-cracks, their applicability in different nondestructive testing (NDT) problems has been investigated in numerous studies. These studies utilize frequency domain analysis to detect the generation of higher harmonics because of the formation of defects in the inspected medium. Frequency domain analysis based on the Fourier transform is a significant approach used in linear systems; however, it may not perform adequately on nonlinear systems. Hence, studies on nonlinear dynamics and physics consider analyzing systems' behavior in the phase-space domain. In contrast to the frequency domain analysis, which can result in information loss, analysis in the phase-space domain retains all the information regarding a system's states. Here, we investigate the nonlinearities induced by poor interlayer bonding in polymer-based additive manufactured parts in the phase-space domain. It is convenient to characterize the nonlinearity in the phase-space domain because it provides a geometrical representation of a system's states. Two types of low quality interlayer bond are considered. The first type is simulated artificially while the second type is manufactured by reducing the bond quality during the printing process. The analysis verified that the received ultrasonic signals exhibit classical nonlinear behavior in the phase-space domain while interacting with simulated poor interlayer bonds. In addition, the results showed that the behavior of ultrasonic waves is amplitude-dependent and evolves into models that have not been previously reported. Furthermore, Largest Lyapunov Exponent (LLE) is used to quantify the behavior of nonlinear ultrasonic waves while interacting with poor interlayer bonds. Using LLE, it was observed that the divergence rate of the phase-space trajectories depends on the amplitude of the excitation. This observation quantitatively proves that nonlinear behavior of ultrasound while interacting with poor interlayer bonds can be amplitude-dependent. The results of both simulated and inherent poor interlayer bond cases showed that LLE can be used as a reliable quantitative damage-sensitive feature to detect and potentially characterize weak bonds, which are difficult to detect using conventional approaches. Additionally, the reported results in the phase-space domain provide a basis for proposing a new mathematical model for ultrasonic waves interacting with poor interlayer bonds.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compressive strength of the plastic-bonded explosive surrogate idoxuridine under quasistatic and dynamic compression

Inert simulant materials, or “mocks”, are often used as surrogates for plastic-bonded explosives (PBX) in non-detonative tests in order to mitigate hazards. Mocks should reproduce as many non-detonative properties of the explosive as possible, including structural behavior in a variety of thermal and mechanical environments. Recently, the molecular crystal idoxuridine (IDOX) has been identified as an ideal mock for the main component in the explosive polymer-matrix composite PBX 9501, and has performed favorably under quasistatic loading conditions. Here, in order to assess robustness over a range of mechanical environments, plastic-bonded IDOX was compression tested from 0.001/s to 2000/s strain rates and compared to PBX 9501 historical data. Plastic-bonded IDOX showed good agreement to PBX 9501 across these strain rates, justifying continued development and production as a mock.

Burch, Alexandra C.↗
DOE OSTI2023

Salt Transport in Crosslinked Hydrogel Membranes Containing Zwitterionic Sulfobetaine Methacrylate and Hydrophobic Phenyl Acrylate

Produced water is a by-product of industrial operations, such as hydraulic fracturing for increased oil recovery, that causes environmental issues since it includes different metal ions (e.g., Li+, K+, Ni2+, Mg2+, etc.) that need to be extracted or collected before disposal. To remove these substances using either selective transport behavior or absorption-swing processes employing membrane-bound ligands, membrane separation procedures are promising unit operations. This study investigates the transport of a series of salts in crosslinked polymer membranes synthesized using a hydrophobic monomer (phenyl acrylate, PA), a zwitterionic hydrophilic monomer (sulfobetaine methacrylate, SBMA), and a crosslinker (methylenebisacrylamide, MBAA). Membranes are characterized according to their thermomechanical properties, where an increased SBMA content leads to decreased water uptake due to structural differences within the films and to more ionic interactions between the ammonium and sulfonate moieties, resulting in a decreased water volume fraction, and Young’s modulus increases with increasing MBAA or PA content. Permeabilities, solubilities, and diffusivities of membranes to LiCl, NaCl, KCl, CaCl2, MgCl2, and NiCl2 are determined by diffusion cell experiments, sorption-desorption experiments, and the solution-diffusion relationship, respectively. Permeability to these metal ions generally decreases with an increasing SBMA content or MBAA content due to the corresponding decreasing water volume fraction, and the permeabilities are in the order of K+ > Na+ > Li+ > Ni2+ > Ca2+ > Mg2+ presumably due to the differences in the hydration diameter.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

Propagation of crazing in viscoelastic media

In response to a tensile stress glassy polymers exhibit crazing (surface cracks) which is a phenomenon of considerable practical and theoretical importance in the use of many plastics. An attempt is made to demonstrate how craze growth behavior is affected by the craze density (which is defined as the total number of crazes per unit surface area) surrounding the craze.

Zhang, Z. D.↗