Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Iron oxide waste form for stabilizing 99 Tc

Crystals of goethite were synthesized with reduced technetium [{sup 99}Tc(IV)] incorporated within the solid lattice. The presence of {sup 99}Tc(IV) as a substituting cation in the matrix and 'armoring' by an additional layer of precipitated goethite isolated the reduced {sup 99}Tc(IV) from oxidizing agents. These products were used to make monolithic pellets to quantify an effective diffusion coefficient for {sup 99}Tc from goethite waste form contacted with a synthetic Hanford IDF (integrated disposal facility) pore water solution (pH = 7.2, I = 0.05 M) at room temperature for up to 120 days in static reactors. XANES analysis of the goethite solids recovered post-run demonstrated that the {sup 99}Tc in the goethite crystals remains in the reduced {sup 99}Tc(IV) state. The slow release of pertechnetate concentration with time in the static experiments with the monolith followed a square root of time dependence, consistent with diffusion control for {sup 99}Tc release. An apparent diffusion coefficient of 6.15 x 10{sup -11} cm{sup 2}/s was calculated for the {sup 99}Tc-goethite pellet sample and the corresponding leaching index (LI) was 10.2. The results of this study indicate that technetium can be immobilized in a stable, low-cost Fe oxide matrix that is easy to fabricate and these findings can be useful in designing long-term solutions for nuclear waste disposal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electrical conductivity of Ca{sub 1-x}Sr{sub x}Ti{sub 0.65}Fe{sub 0.35}O{sub 3-{delta}}, x = 0, 0.5 and 1, polycrystalline compounds in the 300-500 K range

Highlights: Black-Right-Pointing-Pointer Fe-doped Sr and Ca titanates were synthesized by chemical and solid state reaction. Black-Right-Pointing-Pointer SPM images show striking differences in samples prepared by the two routes. Black-Right-Pointing-Pointer Impedance spectroscopy measurements show different electrical behaviors. Black-Right-Pointing-Pointer Correlations between the two macroscopic observations are shown. -- Abstract: Bulk and grain boundary electrical conductivity of oxygen deficient Ca{sub x}Sr{sub 1-x}Ti{sub 0.65}Fe{sub 0.35}O{sub 3-{delta}}, x = 0, 0.5 and 1.0, polycrystalline specimens were evaluated by impedance spectroscopy measurements in the 5 Hz-13 MHz frequency range from 300 to 500 K. The ceramic powders were synthesized by solid state reaction and by a chemical route, the polymeric precursor technique. The X-ray diffraction of the samples at room temperature shows the following perovskite crystalline structures: cubic for x = 0 and orthorhombic for x = 0.5 and 1.0. The impedance plots are composed of two semicircles ascribed to grains (bulk) and interfaces (grain boundaries) contributions. The impedance data show that sintered pellets using powders prepared by solid state synthesis present higher intergranular and intragranular resistivity values than pellets prepared by the chemical route. Observations of scanning probe microscopy topographic images of the surfaces of the sintered pellets show evident differences between the grain morphology of the pellets prepared with powders synthesized by the two routes.

36 MATERIALS SCIENCE↗

Strong photoluminescence emission at low dopant amount in YAG:Ce and YAG:Eu phosphors

Highlights: • YAG:Ce and YAG:Eu materials were prepared by solid state reaction. • Pure YAG phase can be obtained at 1300 °C. • High density materials were synthesized at 1600 °C for 10 h. • The highest PL emission was observed for the YAG:Ce{sub 0.01} and YAG:Eu{sub 0.1} samples. - Abstract: YAG:Ce and YAG:Eu phosphors have been prepared by solid state reaction. The use of submicrometric powders allows preparing pellets with high density, enhancing the photoluminescence (PL) properties. Pellets were prepared by uniaxial pressing and the influence of the thermal treatment on the microstructural and optical properties were also studied. Pure YAG phase was obtained at 1400 °C during 1 h and high density pellets (97%) after sintering at 1600 °C for 10 h. The highest PL emission was achieved for the sintered YAG:Ce and YAG:Eu pellets doped with low dopant concentrations (0.01 mol% for Ce and 0.1 mol% for Eu). Finally, increasing the Ce and Eu concentration the PL intensity decreases and the dopants occupy different positions than the Y one in the YAG lattice.

36 MATERIALS SCIENCE↗

Converting campus waste into renewable energy – A case study for the University of Cincinnati

Highlights: • A case study to show the benefits of waste-to-energy projects at a university. • Evaluated the technical and economic feasibilities as well as GHG reduction. • A tool for other universities/communities to evaluate waste-to-energy projects. - Abstract: This paper evaluates the implementation of three waste-to-energy projects at the University of Cincinnati: waste cooking oil-to-biodiesel, waste paper-to-fuel pellets and food waste-to-biogas, respectively. The implementation of these waste-to-energy (WTE) projects would lead to the improvement of campus sustainability by minimizing waste management efforts and reducing GHG emissions via the displacement of fossil fuel usage. Technical and economic aspects of their implementation were assessed and the corresponding GHG reduction was estimated. Results showed that on-site implementation of these projects would: (1) divert 3682 L (974 gallons) of waste cooking oil to 3712 L (982 gallons) of biodiesel; (2) produce 138 tonnes of fuel pellets from 133 tonnes of waste paper (with the addition of 20.75 tonnes of plastics) to replace121 tonnes of coal; and (3) produce biogas that would be enough to replace 12,767 m{sup 3} natural gas every year from 146 tonnes of food waste. The economic analysis determined that the payback periods for the three projects would be 16 months for the biodiesel, 155 months for the fuel pellet, and 74 months for the biogas projects. The reduction of GHG emission from the implementation of the three WTE projects was determined to be 9.37 (biodiesel), 260.49 (fuel pellets), and 11.36 (biogas) tonnes of CO{sub 2}-eq per year, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Biomass gasification for liquid fuel production

In our old fix-bed autothermal gasifier we tested wood chips and wood pellets. We make experiments for Czech company producing agro pellets - pellets made from agricultural waste and fastrenewable natural resources. We tested pellets from wheat and rice straw and hay. These materials can be very perspective, because they dońt compete with food production, they were formed in sufficient quantity and in the place of their treatment. New installation is composed of allothermal biomass fixed bed gasifier with conditioning and using produced syngas for Fischer - Tropsch synthesis. As a gasifying agent will be used steam. Gas purification will have two parts - separation of dust particles using a hot filter and dolomite reactor for decomposition of tars. In next steps, gas will be cooled, compressed and removed of sulphur and chlorine compounds and carbon dioxide. This syngas will be used for liquid fuel synthesis.

09 BIOMASS FUELS↗

Plasma behaviour at high beta and high density in the Madison Symmetric Torus RFP

Pellet fuelling of improved confinement Madison Symmetric Torus (MST) plasmas has resulted in high density and high plasma beta. The density in improved confinement discharges has been increased fourfold, and a record plasma beta (beta(tot) = 26%) for the improved confinement reversed-field pinch (RFP) has been achieved. At higher beta, a new regime for instabilities is accessed in which local interchange and global tearing instabilities are calculated to be linearly unstable, but experimentally, no severe effect, e. g., a disruption, is observed. The tearing instability, normally driven by the current gradient, is driven by the pressure gradient in this case, and there are indications of increased energy transport ( as compared with low-density improved confinement). Pellet fuelling is also compared with enhanced edge fuelling of standard confinement RFP discharges for the purpose of searching for a density limit in MST. In standard-confinement discharges, pellet fuelling peaks the density profile where edge fuelling cannot, but transport appears unchanged. For a limited range of plasma current, MST discharges with edge fuelling are constrained to a maximum density corresponding to the Greenwald limit. This limit is surpassed in pellet-fuelled improved confinement discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Non-destructive Preirradiation Assessment of UN / U-Si “LANL1” ATF formulation

The goal of the Advanced Non-destructive Fuel Examination (ANDE) work package is the development and application of non-destructive neutron imaging and scattering techniques to ceramic and metallic nuclear fuels, ultimately also to irradiated fuels. The results of these characterizations provide complete pre- and post-irradiation on length scales ranging from mm to nm, guide destructive examination, and inform modelling efforts. Besides technique development and application to samples to be irradiated, the ANDE work package also examines possible technologies to provide these characterization techniques pool-side, e.g. at the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) using laser-driven intense pulsed neutron and gamma sources. Neutron tomography and neutron diffraction characterizations were performed on nine pellets; four UN/ U-Si composite formulations (two enrichment levels), three pure U 3 Si 5 reference formulations (two enrichment levels), and two reject pellets with visible flaws (to qualify the technique). The 235 U enrichments ranged from 0.2 to 8.8 wt. %. The nitride/silicide composites are candidate compositions for use as Accident Tolerant Fuel (ATF). The monophase U 3 Si 5 material was included as a reference. Pellets from the same fabrication batches will be inserted in the Advanced Test Reactor at Idaho during 2016. We have also proposed a data format to build a database for characterization results of individual pellets. Neutron data reported in this report were collected in the LANSCE run cycle that started in September 2015 and ended in March 2016. This report provides the results for the characterized samples and discussion in the context of ANDE and APIE. We quantified the gamma spectra of several samples in their received state as well as after neutron irradiation to ensure that the neutron irradiation does not add significant activation that would complicate shipment and handling. We demonstrated synchrotron-based 3D X-ray microscopy on the composite fuel materials, providing unparalleled level of detail on the 3D microstructure. Furthermore, we initiated development of shielding containers allowing the characterizations presented herein while allowing handling of irradiated samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analytical Modeling of Biomass Transport and Feeding Systems

The processing of biomass solids in a biorefinery consists of pretreatment, enzyme hydrolysis / concurrent fermentation of sugars to ethanol, product recovery, and drying. Sustainable operation requires a front end that transforms wet solids into a pumpable slurry. Otherwise the biorefinery will suffer unscheduled shut-downs and inefficient operation due to solids that obstruct pumps and other equipment and resist mixing in a bioreactor. Downtime in pioneer biorefineries due to interruptions from materials handling problems has been 50% or more, leading to unsustainable manufacturing processes. This work addresses new technology, predictive computational models, and definition of operational conditions that result in formation of slurries of corn stover at up to 300 g/L using low enzyme loadings (1 to 3 FPU cellulase/g) before the biomass (corn stover) enters the pretreatment step. A team of researchers from Purdue University, Idaho National Laboratory (INL), Forest Concepts, AdvanceBio, Argonne National Laboratory, and DOE BETO have combined their knowledge in agricultural and biological engineering, bioprocess engineering, mechanical engineering, chemical engineering, agricultural economics, materials engineering and enzyme and microbial technology to address the challenge of making lignocellulose flow. This team effort has resulted in the development and validation of conditions that employ low levels of commercial enzyme in an agitated bioreactor to which corn stover pellets are added resulting in formation of slurries at high solids loadings, before pretreatment. This approach overcomes challenges caused by handling of dry, particulate biomass materials at the front end of the biorefinery. The subsequent materials handling issues cause obstruction at pumps, pipes and valves. Formation of high loadings slurries with low yield stress, as reported here, significantly decreases the potential for process interruption and enhances plant operability. Key advances in the knowledge of how slurry formation occurs is reported here and in recently published journal papers. We found that pellets are needed to achieve high solids loading, and that commercial enzymes are effective in forming slurries of corn stover particles from pellets that have not been pretreated. Our work has resulted in models that predict solids behavior for formation of compressed solids and pellets that in turn facilitate slurries made of high concentrations of corn stover particles. A computational model was developed that gives mechanistic insights into properties of particles and mixing process that gives the slurry rheology needed to facilitate pumping. Hence, the corn stover may be pumped into a pretreatment reactor in place of auguring in solids against high pressure which is a root cause of interruptions at the front end of a biorefinery. Subsequent mixing in enzyme and microbial bioreactors results in conversion of lignocellulose to sugars in a biorefinery in agitated bioreactors, with flows in and out of the vessels being less likely to be interrupted due to plugging or materials handling problems. The obtained data coupled to process models, techno-economic assessment (TEA) and Life Cycle Analysis (LCA) were used to assess whether this approach is practical. These results are based on a foundation of laboratory characterization and pilot runs. The NREL biochemical sugar model was utilized to carry out techno-economic analysis of enzyme catalyzed liquefaction followed by enzyme hydrolysis. The minimum sugar selling price was between 17.5 and 18.3 ¢/pound or about the same as calculated by the NREL model for dilute acid pretreatment followed by enzyme hydrolysis. Life cycle analysis (LCA) based on Argonne’s Greet Model showed the enzyme catalyzed route had the lowest greenhouse gas emissions of the three combinations studied (i.e., enzyme, enzyme mimetic, and enzyme + mimetic combined). GHG emissions for enzyme-based corn stover liquefaction step, alone, were about 21 g CO 2 -equivalent/kg of liquefied slurry. We believe this approach will further enhance operability of a pioneer biorefinery, and bring large-scale conversion of lignocellulosic biomass to low carbon footprint biofuels closer to implementation.

09 BIOMASS FUELS↗

Chapter 8 - Challenges and Opportunities for International Trade in Forest Biomass. In the book Mobilisation of Forest Bioenergy in the Boreal and Temperate Biomes.

In an effort to reduce fossil fuel consumption, the use of woody biomass for heat and power generation is growing. Key destination markets will be countries within the European Union (EU), particularly the United Kingdom (UK), the Netherlands, Denmark, and Belgium. While demand from Asia (particularly South Korea and Japan) will also increase, it will continue to play a secondary role. Across the EU, adoption of sustainability criteria for forest biomass based on the Renewable Energy Directive (RED) 2009/28/EC or similar criteria is likely. In the UK, the largest market for traded wood pellets, such criteria have already been proposed. As of 2015, only forest biomass that achieves at least a 60% reduction in GHG emissions relative to the EU fossil fuel electricity average can be used for bioenergy production, and proof of Sustainable Forest Management (SFM) is required. In the Netherlands, the energy industry and non-governmental organizations achieved principal agreement on sustainability criteria for solid biomass, but issues of compliance testing and monitoring must still be addressed. In Flemish Belgium, the sustainability requirements for bioliquids may soon be applied to woody biomass. In Denmark, a voluntary industry agreement is set to ensure that all bioenergy production by 2019 is conducted sustainably. At present, internationally traded wood pellets from temperate and boreal biomes originate primarily from the United States (US), Canada, and Russia. Among these, Canada offers large stretches of SFM-certified forests, but the US Southeast has seen the strongest increase in wood pellet production and export in recent years. The expansion of pellet production in the US Southeast is mainly linked to available forest inventory (pulpwood in particular)and the competitive advantage gained by the relative proximity to demand markets in the EU. In addition to the mobilization barriers observed in supply chains at the local and national scale, limitations in the supply of forest biomass for international trade will be influenced by regulatory measures that could restrict the trade of specific feedstock fractions.

09 BIOMASS FUELS↗

A study of transient FGR by integral LOCA tests

A study of transient fission gas release (FGR) was performed by means of two out-of-pile LOCA tests in a hot cell facility. Irradiated fuel rod segments with lengths of roughly 80 mm and burnups of 64 MWd/kgU were subjected to simulated water-cooled reactor LOCA transients in an integral LOCA test device. The segments were heated to a maximum temperature of 1000 Celsius degrees and the increase in rod inner pressure resulting from fission gas release and increased gas temperature during the transient was measured. The first release of gas occurred at temperatures close to 450 Celsius degrees, which suggests a burst release mechanism that may be linked to the onset of grain boundary fracturing. At the end of the simulated transients, gas samples were taken from the fuel rod segments for study by gas mass spectroscopy. The transient fission gas release was measured and amount to roughly 13 % of the calculated pre-test rod inventory of Kr and Xe. Isotopic ratios of the released gas indicated that transient FGR originated from the whole pellet and not only the pellet periphery. The tested segments were also studied by light-optical microscopy to determine pellet porosity, pellet crack pattern and fuel fragmentation. The extent of fine fuel fragmentation was found to be small and limited to the periphery of the fuel. The determined amount of transient fission gas release can be added to the database of fuel rod design codes to more accurately describe the LOCA cladding strains and burst temperatures in the future.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

TREAT reactor LEU fuel-clad chemical interaction empirical modeling analysis

DOE is converting TREAT (Transient Reactor Test) facility from its existing highly enriched uranium (HEU) core to a low-enriched uranium (LEU) core. In order to assess the magnitude of chemical interaction between fuel and cladding materials during physical contact under expected TREAT operational limits, planned transients tests, and reactivity accident scenarios, a combination of experimental testing and thermodynamic modeling was performed to predict the expected chemical interactions among fuel and cladding chemical constituents. Thermodynamic calculations were then validated with empirical data from experiments that emulate TREAT's expected upper operational limits. Pellet samples composed of LEU oxide powder dispersed in a graphite matrix had intimate contact with zirconium-based alloy cladding. The samples were subjected to long-term isothermal heating under high vacuum. Specimen characterization consisted of scanning electron microscopy, x-ray diffraction analysis, and x-ray tomography. ThermoCalc software and Ellingham's diagrams were used for thermodynamic calculations. The X-ray tomography and SEM analysis of the pellets showed a homogeneous distribution of UO{sub 2} particles within the graphite matrix with isolated larger UO{sub 2} agglomerates. The SEM analysis showed the formation of a lamellar structure between the large UO{sub 2} agglomerate and the graphite matrix. This is an indication that diffusion is taking place at a rather moderate temperature and reaction time during the pellet fabrication. Secondary phases, with high Al and Mg content, were detected inside a UO{sub 2} agglomerate using SEM in SE/EBSD mode and chemical analysis with EDS. LEU feedstock impurities, as Al and Mg, seem to promote the chemical reactivity between UO{sub 2} particles and graphite matrix. XRD analysis of a pellet sample showed the presence of UO{sub 2} and graphite, but no other crystalline phases were detected with this technique. Thermodynamic analysis through the use of Ellingham diagrams showed that within TREAT's operational to reactivity accident temperature (278-820 Celsius degrees), UO{sub 2} can be reduced to U metal by Zr due to a more favorable ΔG for the oxidation of Zr.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fabrication of advanced accident tolerant U-Si fuel forms

Prospective advanced accident tolerant UN-USi fuel forms for light-water reactors are being studied at Los Alamos National Laboratory. In this paper we present a recent effort to fabricate and characterize U{sub 3}Si{sub 5} and UN-U{sub 3}Si{sub 5} fuel. The U{sub 3}Si{sub 5} is prepared by arc-melting stoichiometric amounts of uranium and silicon metals. The arc melting process consists of cutting U metal plate into small pieces that can be placed in a tri-arc furnace for melting. The material is slowly heated until a uniform melt of the U and Si is achieved. The fabrication of the U{sub 3}Si{sub 5} pellets followed a conventional cold-press and sinter process. As for the fabrication of UN-U{sub 3}Si{sub 5}, the uranium nitride (UN) feedstock powder was synthesized using carbothermic reduction nitridation. The UN is milled and sieved to sub-74 μm. The UN was mixed with EBS (ethylene bis-stearamide) and milled for 45 minutes. The UN-EBS was combined with 10 wt.% U{sub 3}Si{sub 5} powder (equivalent to 15 vol.% in UN) and additional EBS. The fabrication of the UN-U{sub 3}Si{sub 5} pellets followed a conventional cold-press and sinter process similar to that used to fabricate the U{sub 3}Si{sub 5} pellets. A sample UN-U{sub 3}Si{sub 5} pellet was cross-sectioned, ground, and polished for optical microscopy. The UN and U{sub 3}Si{sub 5} phases are apparent as well as pores and micro-cracks. The affect of micro-cracking on fuel performance is unknown and should be assessed during post-irradiation examination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary analysis of FCM fuel thermal-mechanical performance under normal and transient conditions

Fully ceramic microencapsulated (FCM) fuel is a candidate fuel form to replace commercial UO{sub 2} fuel rod in LWR to enhance fuel reliability under accident conditions. The FCM pellet consists of TRISO particles embedded inside the dense SiC matrix. This fuel design is more complex than conventional LWR fuel, which needs new fuel performance models or analysis tools to assist fuel design and concept evaluation. In this paper an attempt was made to develop a finite element method to analyze FCM fuel pellet thermal-mechanical performance. Three idealized cases of normal operation, power ramp, and LOCA were analyzed. The results showed that the temperature distribution and stress distribution of FCM pellet exhibited a strong non-uniformity. The irradiation strain and creep of buffer layer and PyC (pyrolytic carbon) layers had a strong effect on the mechanical performance of FCM pellet. The hoop stresses of SiC layers and SiC matrix increased significantly during the LOCA and varied with radial positions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Accident tolerant, non-oxidizable MOX fuel fabrication

Thorium dioxide (ThO{sub 2}) has a set of physical-chemical properties that make it well suited to serve as a nuclear fuel matrix: it has a very high melting point, it cannot be further oxidized, it has low leachability in water, reasonable thermal conductivity (better than UO{sub 2}), and of course it is fertile. Collectively, these properties allow for a fuel ceramic with increased in / out of core stability. As such, Thor Energy and a consortium of entities that include Westinghouse, KAERI, Fortum, NNL, ITU and IFE have recently fabricated (Th,Pu)O{sub 2} pellet specimens in Norway. The Th-MOX production methodology was developed over the course of 2 years of ceramic production trials involving Ce-Th oxide mixtures. It was understood that parameters developed for CeO{sub 2} material might need to have been modified if trial results with PuO{sub 2} led to sub-optimal pellets. Among observations made in this work, the most important production parameter was the preparation of constituent / mixed powders. Correct powder morphology was key to achieving high fuel densities. The process parameters developed for (Th,Ce)O{sub 2} pellets were adopted with the expectation that these would serve as a sound basis for obtaining dense, homogeneous (Th,Pu)O{sub 2} fuel ceramic. The Th-MOX fuel manufacture campaign was successful in producing enough (Th,Pu)O{sub 2} pellets to assemble two 30 cm long fuel pins for testing in the Halden test reactor. These fuel rods will be fitted with various instruments to enable temperature, fission gas release and dimensional changes to be measured while operating at power in conditions similar to those of a BWR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermo mechanical analysis of fully ceramic microencapsulated fuel during in-pile operation

A proposed fuel for improved performance in LWRs (Light Water Reactors) is FCM (fully encapsulated micro-ceramic) fuel concept that involves TRISO (Tri-structural-Isotropic) fuel particles embedded in a NITE (Nano Infiltrated Eutectic) silicon carbide matrix. TRISO fuel particles contain a spherical fuel kernel that will likely range from about 500 to in excess of 800 μm in diameter. The kernel and buffer layer are then typically coated with 3 isotropic layers consisting of a dense inner pyrolytic carbon (IPyC), a silicon carbide (SiC) layer, and an outer layer of dense, pyrolytic carbon (OPyC). These layers are typically around 40 μm thick, but can range from 20 to 60 μm. The TRISO particle packing fraction in the NITE-SiC matrix is expected to be 40-45 vol.%. The release of radioactivity into the coolant is dependent on the integrity of the silicon carbide layer of the TRISO particles and the NITE-SiC matrix. BISON, a code under development by Idaho National Laboratory, has been built on the Multi-physics Object Oriented Simulation Environment (MOOSE). MOOSE is a massively parallel, finite element computational system that uses a Jacobian-free, Newton-Krylov (JFNK) method to solve coupled systems and non-linear partial differential equations. A single particle comparison to fuel performance codes such as PARFUME was conducted and demonstrated that BISON is able to simulate the required physics. FCM pellets embedded with homogenous particles were simulated. It was found that the interior matrix temperature was predicted to be considerably lower than for an equivalent UO{sub 2} pellet. The swelling dependence on temperature created a compressive region around the perimeter of the pellet. However, at fluences above 6.10{sup 25} neutrons/m{sup 2}, the swelling of the pyrolytic carbon might cause significant tensile stresses and possible cracks near the surface of the pellet. This suggests that the pyrolytic carbon swelling may be an important factor in the lifetime of this fuel type.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enhanced Thermal Conductivity UO{sub 2}-BeO and UO{sub 2}-SiC Fuels Behavior

Commercial light-water reactors currently use UO{sub 2} as a nuclear fuel, which has demonstrated several desirable characteristics. However, UO{sub 2} has a low thermal conductivity that leads to the development of a large temperature gradient across the fuel pellet. This temperature gradient contributes to limits in the operational performance of the reactor due to effects that include thermal stresses causing pellet cladding interaction and the release of fission product gases as demonstrated. These high fuel temperatures can be decreased and reactor performance improved by developing an enhanced thermal conductivity nuclear fuel. A high thermal conductivity nuclear fuel would decrease fuel temperatures and facilitate a reduction in pellet cladding interaction through lessening thermal stresses that result in fuel cracking, relocation, and swelling as described. Additionally, fission gas release would be decreased allowing for higher fuel burn-up, and the safety of the reactor would be improved with a faster thermal response and less stored energy in the fuel pins. A ceramic-ceramic composite nuclear fuel has an increased effective thermal conductivity due to adding a second compatible and high thermal conductivity ceramic to UO{sub 2}. SiC and BeO are two materials that demonstrate compatibility with UO{sub 2} and have a high thermal conductivity. In summary, the enhanced thermal conductivity UO{sub 2}-BeO and UO{sub 2}-SiC fuel performance has been modelled in a light water reactor, and a more complete and detailed understanding was achieved for enhanced thermal conductivity UO{sub 2}-BeO and UO{sub 2}-SiC fuels. BeO and SiC have high melting point, low neutron absorption, low thermal expansion coefficient and chemical compatibility with current UO{sub 2} fuels which makes them a suitable material for thermal conductivity enhancement. In our modeling and simulation work, the enhanced thermal conductivity nuclear fuel showed the capability of decreasing the fuel temperatures, increasing the gap total conductance, reducing the fission gas release, decreasing the gap/plenum pressure, lessening oxygen redistribution, and facilitating a reduction in pellet cladding interaction through lessening thermal stresses that result in fuel cracking, relocation, and swelling. The safety of the reactor operation would be then improved. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Techno-economic analysis of renewable energy source options for a district heating project

With the increased interest in exploiting renewable energy sources for district heating applications, the economic comparison of viable options has been considered as an important step in making a sound decision. In this paper, the economic performance of several energy options for a district heating system in Vancouver, British Columbia, is studied. The considered district heating system includes a 10 MW peaking/ backup natural gas boiler to provide about 40% of the annual energy requirement and a 2.5 MW base-load system. The energy options for the base-load system include: wood pellet, sewer heat, and geothermal heat. Present values of initial and operating costs of each system were calculated over 25-year service life of the systems, considering depreciation and salvage as a negative cost item. It was shown that the wood pellet heat producing technologies provided less expensive energy followed by the sewer heat recovery, geothermal and natural gas systems. Among wood pellet technologies, the grate burner was a less expensive option than powder and gasifier technologies. It was found that using natural gas as a fuel source for the peaking/backup system accounted for more than 40% of the heat production cost for the considered district heating center. This is mainly due to the high natural gas prices which cause high operating costs over the service life of the district heating system. Variations in several economic inputs did not change the ranking of the technology options in the sensitivity analysis. However, it was found that the results were more sensitive to changes in operating costs of the system than changes in initial investment. It is economical to utilize wood pellet boilers to provide the base-load energy requirement of district heating systems Moreover, the current business approach to use natural gas systems for peaking and backup in district heating systems could increase the cost of heat production significantly.

03 NATURAL GAS↗

Neutron diffraction measurements and micromechanical modelling of temperature-dependent variations in TATB lattice parameters

Triaminotrinitrobenzene (TATB) is a highly anisotropic molecular crystal used in several plastic-bonded explosive (PBX) formulations. TATB-based explosives exhibit irreversible volume expansion (“ratchet growth”) when thermally cycled. A theoretical understanding of the relationship between anisotropy of the crystal, crystal orientation distribution (texture) of polycrystalline aggregates, and the intergranular interactions leading to this irreversible growth is necessary to accurately develop physics-based predictive models for TATB-based PBXs under various thermal environments. In this work, TATB lattice parameters were measured using neutron diffraction during thermal cycling of loose powder and a pressed pellet. The measured lattice parameters help clarify conflicting reports in the literature as these new results are more consistent with one set of previous results than another. The lattice parameters of pressed TATB were also measured as a function of temperature, showing some differences from the powder. This data is used along with anisotropic single-crystal stiffness moduli reported in the literature to model the nominal stresses associated with intergranular constraints during thermal expansion. The texture of both specimens were characterized and the pressed pellet exhibits preferential orientation of (001) poles along the pressing direction, whereas no preferred orientation was found for the loose powder. Lastly, thermal strains for single-crystal TATB computed from lattice parameter data for the powder is input to a self-consistent micromechanical model, which predicts the lattice parameters of the constrained TATB crystals within the pellet. The agreement of these model results with the diffraction data obtained from the pellet is discussed along with future directions of research.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗