Southeast Offshore Storage Resource Assessment: Mid-Atlantic
Southeast Offshore Storage Resource Assessment (SOSRA): Mid-Atlantic Region
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Southeast Offshore Storage Resource Assessment (SOSRA): Mid-Atlantic Region
Southeast Offshore Storage Resource Assessment (SOSRA): Eastern Gulf of Mexico
Southeast Offshore Storage Resource Assessment (SOSRA): Eastern Gulf of Mexico
Southeast Offshore Storage Resource Assessment (SOSRA): Eastern Gulf of Mexico
Southeast Offshore Storage Resource Assessment (SOSRA): Eastern Gulf of Mexico
Southeast Offshore Storage Resource Assessment (SOSRA): Eastern Gulf of Mexico
Southeast Offshore Storage Resource Assessment (SOSRA): MAFLA shelf potential
SOUTHEAST REGIONAL CARBON STORAGE PARTNERSHIP: OFFSHORE GULF OF MEXICO: Presentations from 2020 Joint Partnership Meeting with GoMCarb Project
The natural surge and pitch frequencies of semisubmersible offshore wind platforms are typically designed to be below the wave frequencies to avoid direct excitation. However, surge or pitch resonance can be excited by the nonlinear low-frequency loads generated by irregular incident waves. Second-order potential-flow models with added Morison drag have been found to underpredict this low-frequency excitation and response. As part of the OC6 project, Computational Fluid Dynamics (CFD) simulations were performed to enable a better understanding of the low-frequency loads and the limitations of lower-fidelity models. The focus of the current paper is to set up a computationally cost-effective CFD simulation of a fixed semisubmersible platform to investigate nonlinear difference-frequency loads and establish the corresponding uncertainty in the results. Due to the high computing cost, CFD simulations of irregular waves can be challenging. Instead, simulations were performed with bichromatic waves having a shorter repeat period. A preliminary comparison with Quadratic Transfer Functions from second-order potential-flow theory shows that CFD models consistently predict higher nonlinear wave loads at the difference frequency, likely due to flow separation and viscous drag not accounted for in potential-flow theory.
Low level jets (LLJs) in the atmosphere exhibit a local windspeed maximum inthe boundary layer and are commonly observed both over land and in coastal environments. Because LLJs present strong positive shear beneath the maximum (or "jet nose") and negative shear above the nose, they pose a challenge to future offshore wind technology through their impacts on turbine performance and wakes. Summertime LLJs in the Great Plains have been attributed to frictional decoupling triggering an inertial oscillation, whilecoastal LLJs in California or the North Sea have additional driving mechanisms such as baroclinic forcing. By comparison, LLJs in the coastal US Mid-Atlantic have received less attention, with conflicting evidence about the mechanism that triggers these high shear events. Motivated by future wind energy development in the region, this work elucidates the atmospheric mechanisms of LLJ formation in the US Mid-Atlantic. Using observational data from two floating LiDAR buoys deployed bythe New York State Energy Research and Development Authority in the NY Bight, we identify four sustained LLJ events whose windspeeds and directions are well predicted by a WRF simulation (Weather Research and Forecasting Model). From analysis of the WRF data, we find that the four case studies provide evidence of concurrent inertial oscillation, reduced vertical mixing, and baroclinicity. In addition, we use simple atmospheric dynamics and a single-column-model to compare the relative contribution of each of these mechanisms to triggering the LLJ. By improving understanding and predictability of coastal mid-Atlantic LLJs, this work reduces uncertaintiesof wind energy deployment in the region, aiding the US's transition toward renewable energy.
A hybrid offshore wind turbine includes a monopile, friction wheel, and suction bucket.
Poster for presentation at the American Geophysical Union Fall Meeting 2023 detailing work conducted for the Carbon Storage Data Field Work Proposal. This poster presents an inventory and meta-analysis conducted for Carbon Storage Data Task 4, which includes a review of offshore geologic carbon storage projects worldwide including site characterization, resource estimates, and transport information.
To reduce the cost of offshore wind energy through a more efficient design of the floating support structure, T-Omega Wind developed a novel lightweight and shallow-draft platform concept that aims to achieve a wave-following behavior without resonance amplification. The rotor and generator are carried by four tower legs with each leg supported by a shallow-draft float at the base. In preparation for a more detailed analysis, a coupled aero-hydro-elastic model of the proposed concept is developed in OpenFAST. The detailed modeling approach is presented, including a novel application of the SubDyn substructure dynamics module of OpenFAST to approximate the loads on the axle tube at the tower top from the rotor hub bearings. Preliminary results obtained with the OpenFAST model by rigidifying the substructure and blades indicate that the original sizing of the design can lead to large hub acceleration in the axial/surge and pitch directions due to platform-pitch motion. The high axial acceleration also potentially leads to large bending moments in the four tower legs. To address these issues, an updated design is developed with, among other changes, increased float spacing at the tower base and improved shear-transmitting geometry of the tower legs. The new design suggests significantly reduced extreme hub accelerations under the same conditions even with structural flexibility and will be further analyzed in the future through full aero-hydro-servo-elastic simulations.
The National Renewable Energy Laboratory's OpenFAST software is utilized by academics and industry professionals alike to simulate offshore wind turbines. The software's modeling of hydrodynamic loads on heave plates attached to these structures relies on user specified hydrodynamic coefficients. To guide the proper selection of these coefficients and potentially develop a new functionality within OpenFAST that automatically prescribes and/or adjust the heave-plate hydrodynamic coefficients, this paper reviews past literature to examine the dependence of the added mass, damping, and drag coefficients on various relevant non-dimensional parameters, including the Keulegan-Carpenter number, the frequency parameter, and the plate thickness ratio. Existing data in the literature show strong dependence of the hydrodynamic coefficients on the Keulegan-Carpenter number. Consistent trends are observed across a range of different plate geometry, plate porosity, and flow conditions. Secondary dependence of the coefficients on the frequency parameter and plate thickness ratio is also present.
To reduce the cost of offshore wind energy through a more efficient design of the floating support structure, T-Omega Wind developed a novel lightweight and shallow-draft platform concept that aims to achieve a wave-following behavior without resonance amplification. The rotor and generator are carried by four tower legs with each leg supported by a shallow-draft float at the base. In preparation for a more detailed analysis, a coupled aero-hydro-elastic model of the proposed concept is developed in OpenFAST. The detailed modeling approach is presented, including a novel application of the SubDyn substructure dynamics module of OpenFAST to approximate the loads on the axle tube at the tower top from the rotor hub bearings. Preliminary results obtained with the OpenFAST model by rigidifying the substructure and blades indicate that the original sizing of the design can lead to large hub acceleration in the axial/surge direction and in the pitch direction due to platform-pitch motion. The high hub acceleration also potentially leads to large bending moments in the four tower legs. To address the issue identified, an updated design is developed with, among other changes, increased float spacing at the tower base and improved geometry of the tower legs. The new design suggests significantly reduced extreme platform pitch angles under the same conditions and will be further analyzed in the future through full aero-hydro-servo-elastic simulations.
Poster on Carbon Storage Data Task 4: International Offshore Geologic Carbon Storage Inventory and Meta-analysis to be presented at the AAPG CCUS conference March 11-13, 2024.
A method of installing a hybrid foundation for an offshore wind turbine, the method includes providing a monopile, friction wheel, and suction bucket; installing the friction wheel and suction bucket in the sea floor; and inserting the monopile through the opening into the sea floor.
A comprehensive summary of DOE’s role in the nationwide effort to deploy 30 gigawatts (GW) of offshore wind energy in the United States.