Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low Power Mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Quantifying Dynamic On-State Resistance of GaN HEMTs for Power Converter Design via a Survey of Low and High Voltage Devices

Designing and optimizing high switching frequency, ultra-efficient converters requires detailed knowledge of the behavior and parasitic parameters for both active and passive components. Recently, wide bandgap transistors have enabled simultaneous increases in both switching frequency and efficiency due to higher maximum operating junction temperature limits, lower dc on-state resistances, and reduced parasitic inductances and capacitances. Yet, the early acceptance of gallium-nitride (GaN) switches was plagued by detrimental dynamic on-state resistance effects. This complex phenomenon for GaN devices is characterized by deviations in on-state resistance from dc operating characteristics based on design choices such as the magnitude and duration of both voltage and current stress, switching mode, and junction temperature. While device manufacturers have made improvements compared to early generation devices, experimental evidence from a survey of commercial GaN transistors highlight measurable change in on-state resistance still exists due to variations in voltage stress during hard-switching operation. After sharing insights for obtaining low noise measurements, an analysis method along with two metrics are proposed to characterize dynamic on-state resistance measurements for power electronics designers. Furthermore, quantifying the performance of GaN devices with standardized metrics facilitates a fair comparison between different GaN device technologies during converter development, enables manufacturing qualification for GaN switches, and provides a benchmark to catalyze improvement for the next generation of GaN device development.

14 SOLAR ENERGY↗

Machine learning without a processor: Emergent learning in a nonlinear analog network

Standard deep learning algorithms require differentiating large nonlinear networks, a process that is slow and power-hungry. Electronic contrastive local learning networks (CLLNs) offer potentially fast, efficient, and fault-tolerant hardware for analog machine learning, but existing implementations are linear, severely limiting their capabilities. These systems differ significantly from artificial neural networks as well as the brain, so the feasibility and utility of incorporating nonlinear elements have not been explored. Here, we introduce a nonlinear CLLN—an analog electronic network made of self-adjusting nonlinear resistive elements based on transistors. We demonstrate that the system learns tasks unachievable in linear systems, including XOR (exclusive or) and nonlinear regression, without a computer. We find our decentralized system reduces modes of training error in order (mean, slope, curvature), similar to spectral bias in artificial neural networks. The circuitry is robust to damage, retrainable in seconds, and performs learned tasks in microseconds while dissipating only picojoules of energy across each transistor. This suggests enormous potential for fast, low-power computing in edge systems like sensors, robotic controllers, and medical devices, as well as manufacturability at scale for performing and studying emergent learning.

Science & Technology - Other Topics↗

FIRST SEASON QUIET OBSERVATIONS: MEASUREMENTS OF COSMIC MICROWAVE BACKGROUND POLARIZATION POWER SPECTRA AT 43 GHz IN THE MULTIPOLE RANGE 25 {<=} l {<=} 475

The Q/U Imaging ExperimenT (QUIET) employs coherent receivers at 43 GHz and 94 GHz, operating on the Chajnantor plateau in the Atacama Desert in Chile, to measure the anisotropy in the polarization of the cosmic microwave background (CMB). QUIET primarily targets the B modes from primordial gravitational waves. The combination of these frequencies gives sensitivity to foreground contributions from diffuse Galactic synchrotron radiation. Between 2008 October and 2010 December, over 10,000 hr of data were collected, first with the 19 element 43 GHz array (3458 hr) and then with the 90 element 94 GHz array. Each array observes the same four fields, selected for low foregrounds, together covering Almost-Equal-To 1000 deg{sup 2}. This paper reports initial results from the 43 GHz receiver, which has an array sensitivity to CMB fluctuations of 69 {mu}K{radical}s. The data were extensively studied with a large suite of null tests before the power spectra, determined with two independent pipelines, were examined. Analysis choices, including data selection, were modified until the null tests passed. Cross-correlating maps with different telescope pointings is used to eliminate a bias. This paper reports the EE, BB, and EB power spectra in the multipole range l = 25-475. With the exception of the lowest multipole bin for one of the fields, where a polarized foreground, consistent with Galactic synchrotron radiation, is detected with 3{sigma} significance, the E-mode spectrum is consistent with the {Lambda}CDM model, confirming the only previous detection of the first acoustic peak. The B-mode spectrum is consistent with zero, leading to a measurement of the tensor-to-scalar ratio of r = 0.35{sup +1.06}{sub -0.87}. The combination of a new time-stream 'double-demodulation' technique, side-fed Dragonian optics, natural sky rotation, and frequent boresight rotation leads to the lowest level of systematic contamination in the B-mode power so far reported, below the level of r = 0.1.

79 ASTRONOMY AND ASTROPHYSICS↗

Slope and amplitude asymmetry effects on low frequency capacitively coupled carbon tetrafluoride plasmas

We report investigations of capacitively coupled carbon tetrafluoride (CF{sub 4}) plasmas excited with tailored voltage waveforms containing up to five harmonics of a base frequency of 5.5 MHz. The impact of both the slope asymmetry, and the amplitude asymmetry, of these waveforms on the discharge is examined by combining experiments with particle-in-cell simulations. For all conditions studied herein, the discharge is shown to operate in the drift-ambipolar mode, where a comparatively large electric field in the plasma bulk (outside the sheaths) is the main mechanism for electron power absorption leading to ionization. We show that both types of waveform asymmetries strongly influence the ion energy at the electrodes, with the particularity of having the highest ion flux on the electrode where the lowest ion energy is observed. Even at the comparatively high pressure (600 mTorr) and low fundamental frequency of 5.5 MHz used here, tailoring the voltage waveforms is shown to efficiently create an asymmetry of both the ion energy and the ion flux in geometrically symmetric reactors.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Production and heating of overdense plasmas by mode-converted electron Bernstein waves at very low toroidal field in the Compact Helical System

In the Compact Helical System [S. Okamura et al., Nucl. Fusion 39, 1337 (1999)], overdense plasmas whose electron density exceeds the cutoff density were produced and heated for the first time by perpendicularly and/or obliquely launching of 2.45 GHz electron cyclotron waves (ECWs) at very low toroidal field in a very wide range of magnetic field of 20%-120% for the resonant field B{sub res}(=0.0875 T). In these overdense plasmas, absorbed ECW power density measured by the power modulation technique concentrated inside the high density region beyond the cutoff layer for various magnetic configurations where electron cyclotron and upper hybrid resonance layers are scanned in space widely. This fact clearly demonstrates that the electron Bernstein wave (EBW) excited mainly through 'fast extraordinary wave-to-EBW' and/or 'ordinary wave-to-slow extraordinary wave-to-EBW' mode conversion processes plays a key role in producing and heating overdense plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Abrasion wear at high temperature in particle receiver type Concentrating Solar Power Systems

The use of solid particles as a heat transfer fluid in receivers for concentrating solar powerplants has garnered much attention in the past decade. Particles are not only stable at temperatures above 700 °C but are also able to absorb solar energy directly, which gives them a distinct advantage over conventional molten salts. The use of particles can, however, cause material degradation from the flow of hot or cold particles through discharge hoppers or along the inner receiver surfaces and other system components (e.g. tubes, valves etc.), depending on operating mode of the receiver. Stainless steel alloy 316, nickel-based alloy Inconel® 740H®, Haynes 230, and a 60% alumina, low-cement refractory castable from Allied Mineral Products were tested for wear from first-of-a-kind high-temperature low-velocity abrasion-erosion experiments. The tests are designed to simulate potential conditions in Generation 3 falling particle Concentrating Solar Power (CSP) systems. Simultaneous experiments were conducted at room temperature as well to draw comparison on the role of temperature on abrasion wear rates. It was noted that the abrasion wear rate in candidate materials was driven by the oxidation resistance of the material. The findings from these experiments will be used to determine life-time of critical components in particle receiver concentrated solar powerplants.

14 SOLAR ENERGY↗

Edge transport studies in the edge and scrape-off layer of the National Spherical Torus Experiment with Langmuir probes

Transport and turbulence profiles were directly evaluated using probes for the first time in the edge and scrape-off layer (SOL) of NSTX [Ono et al., Nucl. Fusion 40, 557 (2000)] in low (L) and high (H) confinement, low power (P{sub in}∼ 1.3 MW), beam-heated, lower single-null discharges. Radial turbulent particle fluxes peak near the last closed flux surface (LCFS) at ≈4×10{sup 21} s{sup −1} in L-mode and are suppressed to ≈0.2×10{sup 21} s{sup −1} in H mode (80%–90% lower) mostly due to a reduction in density fluctuation amplitude and of the phase between density and radial velocity fluctuations. The radial particle fluxes are consistent with particle inventory based on SOLPS fluid modeling. A strong intermittent component is identified. Hot, dense plasma filaments 4–10 cm in diameter, appear first ∼2 cm inside the LCFS at a rate of ∼1×10{sup 21} s{sup −1} and leave that region with radial speeds of ∼3–5 km/s, decaying as they travel through the SOL, while voids travel inward toward the core. Profiles of normalized fluctuations feature levels of 10% inside LCFS to ∼150% at the LCFS and SOL. Once properly normalized, the intermittency in NSTX falls in similar electrostatic instability regimes as seen in other devices. The L-H transition causes a drop in the intermittent filaments velocity, amplitude and number in the SOL, resulting in reduced outward transport away from the edge and a less dense SOL.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Coherent addition of high power laser diode array with a V-shape external Talbot cavity

Here, we designed a V-shape external Talbot cavity for a broad-area laser diode array and achieved coherent laser beam addition without using a spatial filter. The V-shape external Talbot cavity provides good mode-discrimination and high-power running capability. Coherent laser beam addition of up to 9-W output power at a narrow spectral linewidth (~0.1 nm) is demonstrated. A multi-lobe far-field profile generated by a low filling-factor phase-locked array is confirmed by our numerical simulation.

42 ENGINEERING↗

Flux Eruption Events Drive Angular Momentum Transport in Magnetically Arrested Accretion Flows

We evolve two high-resolution general relativistic magnetohydrodynamic simulations of advection-dominated accretion flows around nonspinning black holes (BHs), each over a duration ~3 × 10 5 GM BH /c 3 . One model captures the evolution of a weakly magnetized (SANE) disk and the other that of a magnetically arrested disk (MAD). Magnetic flux eruptions in the MAD model push out gas from the disk and launch strong winds with outflow efficiencies at times reaching 10% of the incoming accretion power. Despite the substantial power in these winds, average mass outflow rates remain low out to a radius ~100GM BH /c 2 , only reaching ~60%–80% of the horizon accretion rate. The average outward angular momentum transport is primarily radial in both modes of accretion, but with a clear distinction: magnetic flux eruption–driven disk winds cause a strong vertical flow of angular momentum in the MAD model, while for the SANE model, the magnetorotational instability (MRI) moves angular momentum mostly equatorially through the disk. Further, we find that the MAD state is highly transitory and nonaxisymmetric, with the accretion mode often changing to a SANE-like state following an eruption before reattaining magnetic flux saturation with time. The Reynolds stress changes directions during such transitions, with the MAD (SANE) state showing an inward (outward) stress, possibly pointing to intermittent MRI-driven accretion in MADs. Pinning down the nature of flux eruptions using next-generation telescopes will be crucial in understanding the flow of mass, magnetic flux, and angular momentum in sub-Eddington accreting BHs like M87* and Sagittarius A*.

79 ASTRONOMY AND ASTROPHYSICS↗

Multi-device Studies of Pedestal Physics and Confinement in the I-mode Regime

This paper describes joint ITPA studies of the I-mode regime, which features an edge thermal barrier but with L-mode-like particle and impurity transport, and without ELMs. The regime has been demonstrated on Alcator C-Mod, ASDEX Upgrade and DIII-D tokamaks, over a wide range of device parameters and pedestal conditions, including low collisionality. Access to I-mode is independent of heating method (neutral beam injection, ICRH and/or ECRH). Normalized energy confinement H98y,2 ≥ 1 has been achieved for a range of 3≤q95≤4.9 and scales favourably with power. Changes in turbulence in the pedestal region accompany the transition from L-mode to I-mode. The L-I threshold increases with plasma density and current, and with device size, but weakly with BT. The upper limit of power for I-modes increases with toroidal field, and is largest on Alcator C-Mod at B > 5 T. Issues for extrapolation to ITER and other future fusion devices are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal excursion can cause bond problems.

The purpose of this paper is to illustrate the failure mode caused by thermal deformation and how thermal deformation affects bond integrity. Wege bonding in small-signal transistors, microcircuits and LSI circuits is the subject of this work. Repeated switching of the devices between high and low power at a rate that allows thermal expansion and contraction in the interconnecting wire causes the wire to flex at the point of reduced cross-sectional area until finally the wire breaks due to metal fatigue. It was observed that the thermal deformation was related to many factors such as device power dissipation, current density in the wire, wi *e dress and length, thermal time constant and frequency of operation.

Nowakowski, M. F.↗

Television applications of interline-transfer CCD arrays

The design features and characteristics of interline transfer (ILT) CCD arrays with 190 x 244 and 380 x 488 image elements are reviewed, with emphasis on optional operating modes and system application considerations. It was shown that the observed horizontal resolution for a TV system using an ILT image sensor can approach the aperture response limit determined by photosensor site width, resulting in enhanced resolution for moving images. Preferred camera configurations and read out clocking modes for maximum resolution and low light sensitivity are discussed, including a very low light level intensifier CCD concept. Several camera designs utilizing ILT-CCD arrays are described. These cameras demonstrate feasibility in applications where small size, low-power/low-voltage operation, high sensitivity and extreme ruggedness are either desired or mandatory system requirements.

Hoagland, K. A.↗

Solar-powered Rankine heat pump for heating and cooling

The design, operation and performance of a familyy of solar heating and cooling systems are discussed. The systems feature a reversible heat pump operating with R-11 as the working fluid and using a motor-driven centrifugal compressor. In the cooling mode, solar energy provides the heat source for a Rankine power loop. The system is operational with heat source temperatures ranging from 155 to 220 F; the estimated coefficient of performance is 0.7. In the heating mode, the vapor-cycle heat pump processes solar energy collected at low temperatures (40 to 80 F). The speed of the compressor can be adjusted so that the heat pump capacity matches the load, allowing a seasonal coefficient of performance of about 8 to be attained.

Rousseau, J.↗

Performance of computer-designed small-sized four-stage depressed collector for operation of dual-mode traveling wave tube

A computer-designed axisymmetric 2.4-cm-diameter four-stage depressed collectors was evaluated in conjunction with an octave bandwidth, dual-mode traveling wave tube (TWT). The TWT was operated over a wide range of conditions to simulate different applications. The collector performance was optimized (within the constraint of fixed collector geometry which was designed for operation of the TWT at saturation) over the range of TWT operating conditons covered. For operation of the dual-mode TWT at saturation, average collector efficiencies of 81 1/2 and 82 percent for the high and low modes, respectively, were obtained across an octave bandwidth, leading to a three-fold increase in the TWT overall efficiency. For operation of the TWT in the linear, low distortion range, collector efficiencies of 87 to 92 percent were obtained, leading to TWT overall efficiencies as high as 35 percent. For operation of the dual-mode TWT over a 10 to 1 range in output power, overall efficiencies of 14 to 41 percent were obtained.

Ramins, P.↗

Actuators for actively controlled space structures

A free-flying platform of about 4 x 17 m overall dimensions, carrying a variety of imaging and sounding payloads, calls for an intelligent structure with active dynamic control of structural resonances. The actuators for such a structure must be lightweight, require low power, and allow integration into the structure without degradation of its integrity; the dc-to-100 Hz dynamic range required may entail several types of actuators, as is presently emphasized. Broadband damping of higher-order modes requires modeling of the structure with a distributed array of sensors and actuators.

Studer, P.↗

GEC Ferranti piezo vibratory gyroscope

Prototypes of a piezo-electric vibratory angular rate transducer (gyroscope) (PVG) have been constructed and evaluated. The construction is on the lines suggested by Burdess. The sensitive element is a cylinder of radially poled piezo-electric ceramic. The cylinder is metallized inside and out, and the outer metallization is divided into eight electrodes. The metallization on the inside is earthed. A phase locked loop, using pairs of the electrodes, causes the cylinder to vibrate in one of its two fundamental, degenerate modes. In the presence of rotation, some of the vibration is coupled into the outer mode. This can be detected, or suppressed with a closed-up technique and provides a measure of rotation rate. The gyroscope provides a number of advantages over rotating mass and optical instruments: low size and mass, lower power consumption, potentially high reliability, potentially good dormancy, low cost and high maximum rate.

Nuttall, J. D.↗

Upgrade of the SLAC SLED II Pulse Compression System Based on Recent High Power Tests

In the Next Linear Collider (NLC) it is expected that the high power rf components be able to handle peak power levels in excess of 400 MW. We present recent results of high power tests designed to investigate the RF breakdown limits of the X-band pulse compression system used at SLAC. (SLED-II). Results of these tests show that both the TE{sub 01}-TE{sub 10} mode converter and the 4-port hybrid have a maximum useful power limit of 220-250 MW. Based on these tests, modifications of these components have been undertaken to improve their peak field handling capability. Results of these modifications will be presented. As part of an international effort to develop a new 0.5-1.5 TeV electron-positron linear collider for the 21st century, SLAC has been working towards a design, referred to as 'The Next Linear Collider' (NLC), which will operate at 11.424 GHz and utilize 50-75 MW klystrons as rf power sources. One of the major challenges in this design, or any other design, is how to generate and efficiently transport extremely high rf power from a source to an accelerator structure. SLAC has been investigating various methods of 'pulse compressing' a relatively wide rf pulse ({ge} 1 {mu}s) from a klystron into a narrower, but more intense, pulse. Currently a SLED-II pulse compression scheme is being used at SLAC in the NLC Test Accelerator (NLCTA) and in the Accelerator Structures Test Area (ASTA) to provide high rf power for accelerator and component testing. In ASTA, a 1.05 {mu}s pulse from a 50 MW klystron was successfully pulse compressed to 205 MW with a pulse width of 150 ns. Since operation in NLC will require generating and transporting rf power in excess of 400 MW it was decided to test the breakdown limits of the SLED-II rf components in ASTA with rf power up to the maximum available of 400 MW. This required the combining of power from two 50 MW klystrons and feeding the summed power into the SLED-II pulse compressor. Results from this experiment demonstrated that two of the key components of SLED-II; the Magic Tee and the 'Flower Petal' mode converter (converts between TE{sub 10} rectangular and TE{sub 01} circular modes), were not robust enough at higher power levels. Because of this, a major effort is underway to upgrade the existing devices to operate stably at the higher power levels, and also to investigate new components, which have inherently low field enhancement in their design and therefore more robust.

43 PARTICLE ACCELERATORS↗

Model predictive control for matrix converter operating in current control mode with load current estimation

A matrix converter system operating in current control mode is provided. The matrix converter includes a switching matrix coupled between a low voltage side and a high voltage side, wherein the matrix converter is coupled at its low voltage side to a generator for receiving an input power including an input current and transforming the input power into an output power at its high voltage side, wherein a load is coupled to the high voltage side. The control system includes a load observer and a model predictive controller (MPC). The load observer is configured to estimate a load current that flows to the load from the high voltage side of the matrix converter as a function of a switching state of the switching matrix, an output voltage output at the high voltage side of the matrix converter, and the input current. The MPC is configured to select the switching state of the switching matrix to meet one or more control objectives defined by minimization of a multi-objective function that tracks the output voltage and the input current using the estimated load current.

24 POWER TRANSMISSION AND DISTRIBUTION↗