Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High Temperature Reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Thermal Hydraulic Experimental Test Article (FY2020 Status Report)

The Thermal Hydraulic Experimental Test Article (THETA) is a facility that will be used to develop sodium components and instrumentation as well as acquire experimental data for validation of reactor thermal hydraulic and safety analysis codes. The facility will simulate nominal conditions as well as protected/unprotected loss of flow accidents in a sodium-cooled fast reactor (SFR). High fidelity distributed temperature profiles of the developed flow field will be acquired with Rayleigh backscatter based optical fiber temperature sensors. The facility is being designed in partnership with systems code experts to tailor the experiment to ensure the most relevant and highest quality data for code validation. THETA is comprised of a traditional primary and secondary system. The primary system is submerged in the pool of sodium and consists of a pump, electrically heated core, intermediate heat exchanger, and connected piping and thermal barriers (redan). The secondary system, located outside of the sodium pool, consists of a pump, sodium to air heat exchanger, and connected piping and valves. Figure 1 illustrates the main components of the primary system. THETA will be installed in the Mechanisms Engineering Test Loop (METL) with the primary system in the 28 inch Test Vessel #4, Figure 2. The design work for the facility has been completed. Since the FY19 THETA status report, the THETA primary system components have been assembled and tested using de-ionized water. Some results of this testing at select Richardson and Reynolds numbers are included herein. The custom THETA sodium flowmeter (permanent magnet submersible sodium flowmeter) has been built and calibrated using sodium in an auxiliary facility against a NIST traceable vortex shedder type flowmeter. The permanent magnet flowmeter showed excellent performance, following the theoretical equation for measured voltage quite well, with an error < 3.5% at flow rates ranging from 3-24 GPM at temperatures up to 400 °C. The secondary sodium system for heat rejection from intermediate heat exchanger has been analyzed according to ASME code. All secondary side piping, fittings and a U-stamped air-to-sodium heat exchanger have been procured.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Micromechanical response of SiC-OPyC layers in TRISO fuel particles

Tristructural isotropic (TRISO)–coated particle fuel is a proposed fuel for multiple advanced reactor concepts. The performance of the particle depends on whether the silicon carbide (SiC) layer remains intact to prevent the release of metallic and gaseous fission products. Mechanical fracture of the SiC layer is a potential failure mode under various fuel configurations and operating environments, including the potential transmission of matrix-originating cracks through TRISO particles. Furthermore, this study uses instrumented indentation techniques on cross-sectioned surrogate particles to examine the mechanical stability of the critical interface between SiC and the outer pyrolytic carbon (OPyC) layer. The observed behavior at the interface is rationalized by examining the radially dependent fracture behavior of the SiC layer and performing a numerical analysis to quantify the residual stresses that develop during the processing and cross-sectioning of the as-fabricated particle. Characterizing the SiC-OPyC interface of surrogate TRISO particles using nanoindentation provides unique insight into the interface's room-temperature residual stress and mechanical stability. The modeling efforts were used to investigate the experimental procedure further, and the results are presented herein to validate this fuel form's potential mechanical failure modes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Thermal Hydraulic Experimental Test Article (FY21 Final Report)

The Thermal Hydraulic Experimental Test Article (THETA) is a facility that will be used to develop sodium components and instrumentation as well as acquire experimental data for validation of reactor thermal hydraulic and safety analysis codes. The facility will simulate nominal conditions as well as protected/unprotected loss of flow accidents in a sodium-cooled fast reactor (SFR). High fidelity distributed temperature profiles of the developed flow field will be acquired with Rayleigh backscatter based optical fiber temperature sensors. The facility is being designed in partnership with systems code experts to tailor the experiment to ensure the most relevant and highest quality data for code validation. THETA is comprised of a traditional primary and secondary system. The primary system is submerged in the pool of sodium and consists of a pump, electrically heated core, intermediate heat exchanger, and connected piping and thermal barriers (redan). The secondary system, located outside of the sodium pool, consists of a pump, sodium to air heat exchanger, and connected piping and valves. Figure 1 illustrates the main components of the primary system. THETA has been installed in the Mechanisms Engineering Test Loop (METL) with the primary system in the 28 inch Test Vessel #4, Figure 2 and Figure 3. Since the FY20 THETA status report, further water shakedown testing was performed, some final welding modifications were performed, all system components were sanitized, dry assembled, and commissioned. The THETA submersible electromagnetic flowmeter was welded closed to hermetically seal internal components from sodium followed by a helium leak check for the final time. Following installation of THETA into vessel #4, all data acquisition and control systems were brought online and commissioned at room temperature in the argon gas space of the empty vessel. The vessel zone 1 heaters were reinstalled and the flange was then insulated. The vessel 4 heaters were brought to a temperature of 100 °C and the THETA pump was jogged at 600 RPM to ensure it was functioning correctly. The secondary, AC Conduction based electromagnetic pump from CMI Novacast (product number CA-15) was ordered and will be delivered in late calendar year 2021. The custom designed permanent magnet based secondary flowmeter was designed, a drawing package and manufacturing specification created and quote requested from a machine shop. The intermediate heat exchanger design was completed and a drawing package is currently in progress. During the middle of calendar year 2021 the Building 308 sodium scrubber system was shut down in order to replaced some corroded piping and facilitate improvements on the system, thus requiring the sodium in METL to remain frozen. This has imposed a delay in filling vessel 4 with sodium to begin THETA testing. Sodium testing is expected to begin in early fiscal year 2022 as all THETA primary systems are operational.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Analysis of buffer-IPyC separation in TRISO fuel particles

During High Temperature Gas-cooled Reactor (HTGR) operation, and due to the neutron irradiation in the reactor core, damage of the nuclear fuel coating layers occurs. The mechanism of damage formation in the TRISO fuel is explored by the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program, in which the debonding process between coating layers was also investigated. The purpose of this paper is to report simulation results for two models. Firstly, the debonding restricted model, where no gap formation between buffer and IPyC layers is permitted. Secondly, a debonding enabled model, where the gap between those layers is created. The simulations were performed with the Bison code. The inputs of the simulated models are based on data from the AGR-1 experiment. Further, the research included simulations on spherical and aspherical fuel types. The simulations match results obtained by the AGR-1 experiment, which as such shows that the Bison code is a good computational method for simulating the behavior of the gap between buffer and IPyC layers in TRISO fuel. Based on the irradiation experiments, and the Bison simulations, it was concluded that the most common scenario is a gap formation along the buffer-IPyC interface, while the least possible scenario is the situation where there is no gap formation at the buffer-IPyC junction. The computational results confirmed that the sphericity of the fuel influences the thickness of the gap that occurs at the buffer-IPyC junction, in a way that with increasing aspect ratio the gap thickness increases. In addition, the fuel sphericity does not influence the Weibull failure probability. The results obtained for spherical and aspherical fuel are nearly identical.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Water vapor oxidation of SiC layer in surrogate TRISO fuel particles

Under accidental conditions for high temperature gas-cooled reactors (HTGR), the SiC layer in tri-structural-isotropic (TRISO) fuel particles can be exposed to water vapor. In this study, oxidation behaviors of surrogate TRISO fuel particles were investigated in a He-20 vol% water vapor mixed atmosphere at temperatures up to 1600 °C. The growth of the crystalline oxide passivation layer with cracks and pores followed a parabolic law with time, where the maximum was 2.3 μm at 1600 °C. The oxide layer and the SiC surface under the oxide became flattened with increasing temperature, as a function of the silica viscosity and the diffusion path of water vapor. Volatilization of the oxide layer was analyzed using a mechanistic model that an inert gas in oxidizing atmospheres could influence the magnitude of volatilization. The fracture load and strength of the oxidized and thinned SiC layer were numerically estimated to decrease from 2.27 to 1.69 N and from 317 to 299 MPa, respectively, with the SiC thickness decrease from 35 to 32 μm. This prediction indicates that the oxidized SiC layer should retain fission products. Additionally, the mechanical integrity of each layer in the TRISO fuel particle after oxidation was evaluated. The results in this work provide important data for the safety analysis of accidental scenarios in HTGRs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

In-situ microstructure observation of oxidized SiC layer in surrogate TRISO fuel particles under krypton ion irradiation

In accidental scenarios of high temperature gas-cooled reactors, both oxidation of and irradiation to the SiC layer in tri-structural-isotropic (TRISO) fuel particles can change the microstructure and integrity of the fuel elements. Here, in the present study, microstructure and defect evolution in the oxidized SiC layer of surrogate TRISO fuel particles under 1.2 MeV krypton ion irradiation was observed by in-situ transmission electron microscopy. The SiC layers oxidized in water vapor at 1200 °C were irradiated azt room temperature and 800 °C and at damage levels of 0.28–11.2 dpa, respectively. SiC and SiO 2 were found to still be in their crystal structures at the damage level of 11.2 dpa at 800 °C, while SiC was observed to have been amorphized at only 0.56 dpa irradiation at room temperature. The defect number density at 800 °C was an order of magnitude lower than that in the sample irradiated at room temperature. Also, crystalline SiO 2 had higher radiation resistance compared to SiC. A defect reaction rate theory was utilized to understand the fundamental defect evolution process and irradiation resistance difference.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

The effect of Zr on precipitation in oxide dispersion strengthened FeCrAl alloys

Oxide dispersion strengthened (ODS) FeCrAl alloys are promising candidate materials for advanced nuclear reactor applications requiring high-temperature strength, corrosion resistance, and irradiation tolerance. As these alloys have increased in compositional complexity through attempts to use highly reactive elements such as Zr to refine particle sizes and optimize nanoprecipitate dispersion characteristics, much debate has ensued as to the effects of these alloying element additions on alloy properties. In an attempt to reconcile differences in nanoprecipitate distributions reported in the literature over the past decade, a detailed investigation of a recently developed ODS FeCrAl alloy with nominal composition Fe–10Cr-6.1Al-0.3Zr+0.3Y 2 O 3 is presented here using a combination of atom probe tomography (APT), scanning/transmission electron microscopy (S/TEM), and computational thermodynamics modeling. It is illustrated that based on the amount of Zr available in the lattice, Zr competes with Al and Cr to form carbides and nitrides as opposed to oxygen-rich precipitates. This alloy system has a high number density (>10 23 m -3 ) of ~2–4 nm diameter (Y,Al,O)-rich nanoprecipitates, but it is shown that due to the compositional spread and unknown partitioning of Al between the matrix and precipitates, significant challenges still exist for quantifying the exact compositions of these precipitates using APT. However, the noted compositional spread is supported by identified complex oxides yttrium aluminum monoclinic (YAM) and yttrium aluminum garnet (YAG) using S/TEM. As a result of these findings, researchers developing ODS FeCrAl with reactive element additions must pay careful attention to C and N impurities when optimizing reactive element additions.

electron microscopy↗
DOE OSTI2023

Diffusion study of uranium mononitride/zirconium carbide composite for space nuclear propulsion

Here, the next generation of space exploration will require extensive developments in rocket technology. Space nuclear propulsion is of interest due to its high fuel density and power, however, it also has high temperature and stability demands. This study examines a uranium nitride/zirconium carbide ceramic-ceramic particle composite as a potential fuel for these missions. Based on the constituent properties, this fuel composite is expected to be highly thermally efficient and resistant to the hot hydrogen propellant. One of the main concerns with this composite is unknown diffusion behavior between UN and ZrC over time. Diffusion couples and composites were used to determine how these constituents will behave when left in contact at high temperatures. UN and ZrC were found to have limited but observable diffusion at the phase boundary. The resulting phase is a UZr(CN) quaternary phase. UZr(CN) has been examined for other high temperature and gas nuclear reactors with preliminary success; however, there lacks sufficient data to fully qualify this phase. Based on the limited information available, the resultant quaternary phase could be deemed acceptable and even provide better adhesion for the fuel particles (UN) to the matrix (ZrC).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Quantitative measurement of pebble fuel anisotropy using generalized ellipsometry

The renewed development of high-temperature gas-cooled reactors has created a need to modernize pebble fuel quality control methods. One important specification in these methods is the coefficient of thermal expansion (CTE) anisotropy, which reflects graphite grain alignment and affects fuel performance. This study investigates the feasibility of using two-modulator generalized ellipsometry microscopy (2-MGEM) as a potential surrogate metric for CTE anisotropy. Graphite matrix compacts with controlled levels of anisotropy were fabricated by varying pre-pressures during forming and were subsequently characterized using both optical dilatometry and 2-MGEM. Measured responses were compared to an isotropic reference pebble produced using an industrial manufacturing process to provide a practical baseline. The resulting measurements revealed a strong quantitative correlation between the CTE anisotropy ratio and the corresponding diattenuation ratio. However, propagated measurement uncertainties in the optical method were found to limit definitive pass/fail discrimination, highlighting the need for improved precision before qualification as a quality control tool. Still, the results establish a quantitative relationship between optical and CTE anisotropy and support further development of 2-MGEM as a potential surrogate method for evaluating graphite matrix anisotropy in pebble fuel manufacturing.

Raftery, Alicia [ORNL] (ORCID:0000000259076427)↗
DOE OSTI2024

RELAP5-3D validation studies based on the High Temperature Test facility

In the spring and summer of 2019, experiments were conducted at the High Temperature Test Facility (HTTF) that form the basis of an upcoming high-temperature gas-cooled reactor (HTGR) thermal hydraulics (T/H) benchmark. HTTF is an integral effects test facility for HTGR T/H modeling validation. This paper presents RELAP5-3D models of two of those experiments: PG-27, a pressurized conduction cooldown (PCC); and PG-29, a depressurized conduction cooldown (DCC). These models used the RELAP5-3D model of HTTF originally developed by Paul Bayless as a starting point. The sensitivity analysis and uncertainty quantification code, RAVEN was used to perform calibration studies for the steady-state portion of PG-27. Here we developed four PG-27 calibrations based on steady-state conditions. These calibrations all used an effective thermal conductivity equal to 36 % of the measured thermal conductivity, but they differed with respect to the frictional pressure drops and radial conduction models. These models all captured the trends in steady-state temperature distributions and transient temperature behavior well. All four calibrations show room for improvement in predicting the transient temperature rise. The smallest error in temperature rise during the transient was a 21 % underprediction, and the largest was a 48 % underprediction. The errors in transient temperature rise are largely a result of a mismatch in power density between the RELAP5-3D model and the experiment due to the location of active heater rods along the boundary between heat structures in the model. The best of these calibrations was applied to PG-29 to model the DCC. Once again, temperatures during the transient were underpredicted but trends in temperature were captured. The RELAP5-3D model captured trends in the data but could not reproduce measured temperatures exactly. This result is not attributed to deficiencies in the experimental data or to RELAP5–3D itself. Rather, this result likely arises due to the some of the assumptions and decisions made when the RELAP5-3D model was first developed, prior to the execution of HTTF experiments. An agreement in prediction of temperature trends but challenges reproducing HTTF temperatures within measurement uncertainty is consistent with previous analyses of HTTF in the literature. Future RELAP5-3D validation activities centered around HTTF may be able to provide greater insight into the code’s capabilities for HTGR modeling with a more finely nodalized model.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Temperature sensitivity of the equilibrium neutronics and accident analysis of the HTR-10

Pebble-Bed High-Temperature Gas-cooled Reactors (PB-HTGR) are moderated by the graphite in the fuel pebbles and the graphite reflector surrounding the pebble-bed. Because graphite is by far the most abundant material in PB-HTGRs and the primary moderator, accurate modeling of the graphite material, including density, impurities, and temperatures, is crucial for accurate computational modeling and simulation of these reactors. While main characteristics of the graphite components are often known, the local temperature is less well known and often averaged over all components. Here, this work studies the impact of considering accurate temperature profiles in the graphite material on the generation of a small PB-HTGR model at the state of equilibrium operation and on short-term accident progression. The fuel compositions for the PB-HTGR were determined using a jump-in equilibrium modeling method, the Axial Radial Zone Equilibrium Modeling (AR-ZEM) method. In contrast to previous work, the AR-ZEM method was used considering thermal-hydraulic feedback from the MELCOR code to determine temperatures of the fuel pebbles and the surrounding graphite reflector. The consideration of an axial and radial temperature profile in the core and reflector, as opposed to uniform material temperatures, had an impact of almost 1,300 pcm on the equilibrium core eigenvalue and caused significant differences in the discharged plutonium fuel inventory with up to 4.9% and 11.0% for Pu-239 and Pu-242, respectively. To assess the impact on short-term accident progression, two Anticipated Transient Without SCRAM (ATWS) events, a Pressurized Loss of Forced Coolant (PLOFC) and a Control Rod Withdrawal (CRW) with loss of flow, were simulated with MELCOR. The use of temperature profiles in the equilibrium core models did not reveal a significant impact on the temperature, power, or reactivity responses during the transients. In conclusion, a need for consideration of accurate temperature profiles, in particular for the graphite reflector, was found for the generation of equilibrium PB-HTGRs core models using jump-in methods, but detailed temperature profiles may not be necessary when performing conservative transient analysis.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Catalytic Removal of Oxygen Impurities from Pressurized Oxy-Combustion Flue Gas for the Production of High-Purity Carbon Dioxide

Flue gas purification is important for pressurized oxy-combustion systems to produce pure carbon dioxide (CO 2 ) streams ready for storage or utilization. A catalytic approach to removing oxygen (O 2 ) impurities from pressurized oxy-combustion flue gas via reduction with methane (CH 4 ) was investigated in this work. Two types of catalysts were studied: palladium (Pd)-based catalysts supported on titania (TiO 2 ) prepared by incipient wetness impregnation and cobalt–manganese (CoMn) composite catalysts prepared by coprecipitation. The performance of the catalysts was evaluated in a high-pressure–high-temperature, fixed-bed reactor at a pressure of 15 bar and a gas hourly space velocity of 30 000 h –1 (standard conditions), with a simulated feeding gas composed of 3 vol % O 2 , 1.5 vol % CH 4 , and CO 2 as the balance gas. Among the Pd catalysts, 5% Pd/TiO 2 achieved the maximum 86% O 2 removal at ≥350 °C. The CoMn oxide catalysts displayed comparable or better activities for O 2 reduction compared with the Pd catalysts. Among them, the Co 40 Mn 1 catalyst exhibited the best performance, able to reduce 99.9% of O 2 impurities at ~370 °C with negligible carbon monoxide (CO) formation (<10 ppmv). Both trivalent and divalent Co and Mn were detected on the catalyst surface, and the superior activity of Co 40 Mn 1 might be associated with the resultant disordered structure. Furthermore, the activity of the catalyst was not affected by the presence of a trace amount of nitric oxide (NO) gas contaminant. Results of this study provide the basis for scale-up studies in both the synthesis and performance of non-noble metal catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Multiscale Modeling of the Mechanical Response of Silicon Carbide Composite Within the Accelerated Fuel Qualification Framework

The accelerated fuel qualification (AFQ) framework has been used for the initial development of multiscale modeling of silicon carbide (SiC) fiber reinforced composite (SiC-SiC). The AFQ framework provides a methodology to leverage physics-informed multiscale modeling along with a reduced set of empirical test data to reduce the time and cost of licensing and qualification of new nuclear fuel systems while maintaining the overall nuclear power plant safety case. SiC-SiC is being proposed for in-core applications, most notably fuel cladding, for current and next-generation nuclear reactors because of its high temperature stability, irradiation tolerance, and ability to withstand many accident conditions. As these composites exhibit multiscale architectures and complex microstructure-based fracture mechanics, it is an appealing use case for the AFQ methodology. While the end goal of this work is a single multiscale model that can be used for predictive in-core performance, current focus is on the individual various length scale models. Four individual models have been initially developed from microscale to engineering system level to capture key physics-based effects across different length scales. These models include a microscale homogenized tow model, a mesoscale fast Fourier transform–based weave model that integrates the homogenized tow model, a mesoscale finite element–based weave model, and a system-level BISON fuel performance model. Results of these models have undergone an initial comparison with separate-effects test data showing a good match to experimental results. By using the AFQ framework during model development, several near-term benefits have been secured including a reduction in development time for the SiC-SiC cladding, more targeted irradiation testing, and a better understanding of uncertainty.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

NEML2 - THE NEW ENGINEERING MATERIAL MODEL LIBRARY, VERSION 2

SF-22-157 NEML2 is an extension of an earlier open source code developed at ANL (SF-xxxx) called NEML. These libraries provide tools for constructing and using models of engineering materials, with a focus on high temperature materials for nuclear reactor applications. The software include tools for setting up material models, calibrating models, storing models for later use in other simulations, and running simple "material point" simulations of the material behavior. The main difference between NEML and NEML2 is the new software has been complete restructured to run on GPUs and other accelerators in order to improve the performance of methods used to train constitutive models against data and to improve the performance of the final models in production environments, like finite element software. While over time we expect NEML2 to become more-or-less feature complete with NEML we are filing a new software disclosure because (1) the library has been complete restructured and (2) we want to host NEML2 in a separate repository.

MESSNER, MARK↗
DOE OSTI2024

SCALE Input and Result Files Supporting SCALE Inventory and Reactivity Analysis as Part of the Hermes 2021 PSAR Review

This dataset contains input and result files of computational simulations with the SCALE code system. The simulations cover radionuclide inventory and reactivity analyses of a fluoride salt-cooled high temperature pebble-bed reactor (PB-FHR), specifically the Hermes low-power PB-FHR demonstration reactor. Users wanting to reproduce results from this dataset are required to obtain a license to the SCALE code system for which details on the distribution can be found here: https://www.ornl.gov/scale/releases

equilibrium core↗
DOE OSTI2025

SCALE Input and Result Files Supporting SCALE Inventory and Reactivity Analysis of the gFHR

This dataset contains input and result files of computational simulations with the SCALE code system. The simulations cover radionuclide inventory and reactivity analyses of a fluoride salt-cooled high temperature pebble-bed reactor (PB-FHR), specifically the generic FHR benchmark. Users wanting to reproduce results from this dataset are required to obtain a license to the SCALE code system for which details on the distribution can be found here: https://www.ornl.gov/scale/releases

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A new approach for resonance treatment of doubly heterogeneous fuel using the RSE method

A new resonance calculation method for the doubly-heterogeneous (DH) fuels such as high- temperature gas-cooled reactor fuel is proposed based on the resonance calculation based on Spectral Expansion (RSE) method. The concept of pointwise disadvantage factor for fuel grain is taken into account to treat the DH fuels. The verification calculation is carried out for simplified single fuel cell and fuel compact consisting of five fuel cells and graphite moderator. The calculation results indicate that the present method can appropriately handle the space- dependent self-shielding effect for DH fuels. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗