SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
To prevent fatigue due to flow-induced vibrations in metal bellows connected to ducts carrying liquid hydrogen, a study was made which shows that the flexure lines are in general a function of the vibration coupling between the fluid and bellows structure, and the nature of the external environment.
Free vibration of discretely stiffened cylindrical shells with arbitrary end conditions programmed for digital computer, considering flexure, extension, torsion and nonsymmetric stiffener cross section
Unfilled Pyrrone prepared from powder into molded parts for flexural tests at elevated temperatures observed for stability to electron irradiation in air
Three dimensional coupled flexural and attitude dynamics of libration-damped cruciform gravity gradient satellite, discussing effects of orbital eccentricity, solar radiation pressure, etc
Dies of a phenolic molding compound with chopped glass fibers as fill material possess a flexural strength of 20,000 psi and a compressive strength of 28,500 psi.
Report describes capabilities and limitations of flat-conductor cable /FCC/ relative to flexure in bending, folding, rotating, and extending, it also compares FCC mechanical and endurance characteristics with round-wire cable, and compares qualities of various types of insulation for FCC. Several configurations exemplify FCC flexibility.
Fabrication and structural evaluation for regeneratively cooled panels - tensile tests, creep rupture, and flexure tests of brazed plate-fin specimens
Elastic response and characteristics of bias ply aircraft tires subjected to braking forces and simple static flexure
Flexural, shear, bending, tensile, and impact strengths of high modulus, high strength, glass fiber-epoxy resin composites
A program designed to characterize an experimental fluoroelastomer material designated AF-E-124D, is examined. Tests conducted include liquid nitrogen load compression tests, flexure tests and valve seal tests, ambient and elevated temperature compression set tests, and cleaning and flushing fluid exposure tests. The results of these tests indicate the AF-E-124D is a good choice for a cryogenic seal, since it exhibits good low temperature sealing characteristics and resistance to permanent set. The status of this material as an experimental fluorelastomer is stressed and recommended. Activity includes definition and control of critical processing to ensure consistent material properties. Design, fabrication and test of this and other materials is recommended in valve and static seal applications.
The problem of ameliorating the discomfort of passengers on a large air transport subject to flight disturbances is examined. The longitudinal dynamics of the aircraft, including effects of body flexing, are developed in terms of linear, constant coefficient differential equations in state variables. A cost functional, penalizing the rigid body displacements and flexure accelerations over the surface of the aircraft is formulated as a quadratic form. The resulting control problem, to minimize the cost subject to the state equation constraints, is of a class whose solutions are well known. The feedback gains for the optimal controller are calculated digitally, and the resulting autopilot is simulated on an analog computer and its performance evaluated.
The applicability of the finite difference method to propagation problems in shells, and the response of a cylindrical shell with cutouts to both longitudinal and radial transient excitations are investigated. It is found that the only inherent limitation of the finite difference method is its inability to reproduce accurately response discontinuities. The short wave length limitations of thin shell theory create significant convergence difficulties may often be overcome through proper selection of finite difference mesh dimensions and temporal or spatial smoothing of the excitation. Cutouts produce moderate changes in early and intermediate time response of a cylindrical shell to axisymmetric pulse loads applied at one end. The cutouts may facilitate the undesirable late-time transfer of load-injected extensional energy into nonaxisymmetric flexural response.
The work directed towards developing methods of increasing the strength of thin boron films is reported. The program was divided into two main parts. The first involved the improvement of methods for the measurement of the strength of thin films. The second was a study of the effect of condensation of deposition temperature on the strength of the films. Techniques were developed for depositing boron films onto both sides of thin titanium and tantalum foils. Small dogbone sections of boron were made by masking. Strain gauges were then mounted on these to measure failure strains when the films were loaded in tension. Test results were consistent with those obtained by flexure tests. The most important flaws in the boron films appeared to have been generated by either small globules of boron ejected from the melt or small particles (possibly boron dust) on the substrate prior to deposition.
The mathematical formulation associated with the problem of stability of motion of a satellite consisting of a main rigid body and three (or less) pairs of flexible rods is presented. The rods are capable of flexure in two orthogonal directions. Whereas the rotational motion of the body is described by generalized coordinates depending on time alone, the elastic displacements of the rods depend both on spatial position and time. Assuming no external torques, there exist motion integrals in the form of momentum integrals. These integrals can be regarded as constraint equations relating the system velocities, and used to reduce the number of variables describing the motion. The stability analysis has been carried out by means of an extension of the Liapunov direct method. Since the elastic vibrations result in energy dissipation, it is shown that the equilibrium position is asymptotically stable if the Hamiltonian is positive definite and unstable if it can take negative values in the neighborhood of the equilibrium. Determining the sign definiteness of the Hamiltonian is complicated by the fact that it contains spatial derivatives of the elastic displacements. Two methods are presented to cope with this problem. The first, the standard modal analysis in conjunction with series truncation, develops criteria in terms of infinite series associated with the natural modes and frequencies of the elastic rods. The second, the method of integral coordinates, yields closed-form stability criteria involving the system parameters, such as the body moments of inertia, the length and mass distribution of the rods, the lowest natural frequencies of the rods, and the satellite spin velocity.
Both drilled-and solid-ball 120-mm-bore bearings were tested at speeds up to 24,000 rpm to determine skid characteristics. The thrust loads were varied from 5000 lb down to 370 lb. No gross skidding occurred, and the behavior of the two bearing types was generally similar; however, two drilled-ball bearing failures occurred during the skid tests. In the endurance tests, 25 cycles of start, run (for one hour), and stop were completed before a drilled-ball bearing failed. In all three cases, the ball had failed in flexure fatigue.
Activities directed toward the development of methods of measurement for semiconductor materials, process control, and devices are described. Topics investigated include: measurements of transistor delay time; application of the infrared response technique to the study of radiation-damaged, lithium-drifted silicon detectors; and identification of a condition that minimizes wire flexure and reduces the failure rate of wire bonds in transistors and integrated circuits under slow thermal cycling conditions. Supplementary data concerning staff, standards committee activities, technical services, and publications are included as appendixes.
A theoretical elastic analysis is presented for the in-plane shear of a corrugated plate with curvilinear corrugations and with discrete attachments between the ends of the corrugations and the surrounding members. The purpose of the analysis is to obtain information about the effective shear stiffness of the plate and the flexural strains that develop in it during the shearing process as a result of the attendant cross-sectional deformations. The crests and troughs of the corrugation cross section are assumed to be identical circular arcs. The following four kinds of discrete attachment at the corrugation ends are considered in the analysis: (1) point attachments in the troughs, (2) point attachments at the crests and in the troughs, (3) point attachments at mid-height, and (4) point attachments at mid-height, at the crests, and in the troughs.
A peripheral drive belt on the Mariner Mars 1971 tape recorder failed when a thin longitudinal strip separated off one edge. Analysis showed that the most probable cause of failure occurred from flexural fatigue initiating in mechanically weak locations which are introduced into the belt during fabrication. Methyl ethyl ketone, which is employed as a cleaning solvent during fabrication, was found to cause permanent reduction in engineering properties of polyester and could have contributed to the reduction of the fatigue resistance. Fatigue properties of the polyester drive belt are reviewed for the operating condition, as well as the sensitivity of polyester to cleaning solvents and the origin of mechanically weak locations.