Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Entropy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Tailoring grain growth and solid solution strengthening of single-phase CrCoNi medium-entropy alloys by solute selection

In the present study, we selected solutes to be added to the CrCoNi medium-entropy alloy (MEA) based on the mismatch of self-diffusion activation energy (SDQ) between the alloying elements and constituent elements of the matrix, and then investigated their grain growth behavior and mechanical properties. Mo and Al were selected as the solutes for investigation primarily because they have higher and lower SDQ, respectively, than those of the matrix elements; a secondary factor was their higher and lower shear modulus. Their concentrations were fixed at 3 at.% each because previous work had shown these compositions to be single-phase solid solutions with the face-centered cubic structure. Three alloys were produced by arc melting, casting, homogenizing, cold rolling and annealing at various temperatures and times to produce samples with different grain sizes. They were (a) the base alloy CrCoNi, (b) the base alloy plus 3 at.% Mo, and (c) the base alloy plus 3 at.% Al. The activation energies for grain growth of the CrCoNi, CrCoNi-3Mo and CrCoNi-3Al MEAs were found to be ~251, ~368 and ~219 kJ/mol, respectively, consistent with the notion that elements with higher SDQ (in this study Mo) retard grain growth (likely by a solute-drag effect), whereas those with lower values (Al) accelerate grain growth. The room-temperature tensile properties show that Mo increases the yield strength by ~40% but Al addition has a smaller strengthening effect consistent with their relative shear moduli. The yield strength as a function of grain size for the three singlephase MEAs follows the classical Hall-Petch relationship with much higher slopes (> 600 MPa μm -0.5 ) than traditional solid solutions. Furthermore, this work shows that the grain growth kinetics and solid solution strengthening of the CrCoNi MEA can be tuned by selecting solute elements that have appropriate diffusion and physical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Irradiation effects on Al 0.3 CoCrFeNi and CoCrMnFeNi high-entropy alloys, and 316H stainless steel at 500 °C

To evaluate the potential of high entropy alloys (HEAs) for nuclear applications, two HEAs, Al 0.3 CoCrFeNi and CoCrFeMnNi, and a conventional Type 316H stainless steel (SS) were irradiated with 1 MeV krypton ions at 500 degrees C up to 1 dpa, and examined in-situ with a transmission electron microscope (TEM). After irradiation, a high density of ordered L1 2 nanoparticles was observed in Al 0.3 CoCrFeNi. In contrast, no phase transformation was observed in CoCrFeMnNi and 316H SS. In the thin foil regions of TEM samples, stacking-fault tetrahedra were observed in the HEAs. In the thick foil regions, interstitial dislocation loops were observed for all alloys, and the areal loop density increased linearly with foil thickness. The Al 0.3 CoCrFeNi had the largest loop size (the lowest density), followed by the CoCrFeMnNi and then the 316H SS. The higher loop nucleation rate in the 316H SS was attributed to carbon content. Finally, the degree of irradiation hardening was slightly lower for the HEAs than for the 316H SS, which is a promising sign for the nuclear application of HEAs at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heat capacity, entropy, formation energy and spin-fluctuation behavior of U 3 Si 5 from 2.4 to 397.4 K

U-Si intermetallic compounds are of considerable interest for their applications as accident-tolerant nuclear fuels. Here we present low-temperature heat capacity (LTHC) measurements of one of the U-Si phases, U 3 Si 5 , using a Quantum Design Physical Properties Measurement System (PPMS) from 2.4 to 397.4 K. We observed an upturn in C p /T (T) below 10 K and have attributed this behavior to potential spin-fluctuations (SF) with an SF temperature (T sf ) of 27 K. An enhancement of LTHC was also observed, as manifested by a large electronic heat capacity coefficient (γ el ) of 342.9 mJ/mol•K 2 . From the heat capacity data, the following thermodynamic parameters were determined: the characteristic Debye temperature (θ D ) over the temperature range 30 – 397 K is 177 ± 2 K, and the standard entropy ($Δ^{298.15}_0$$S^o$) is 283.3 ± 5.7 J•mol -1 •K -1 (equivalent to 35.4 ± 0.7 J•mol -1 •atom -1 •K -1 ). Combined with our previously measured formation enthalpy ($Δ_fH^°_{el}$) of U 3 Si 5 , the Gibbs free energy of formation of U 3 Si 5 from the elements ($Δ_fG^°_{el}$) was determined to be –45.2 ± 9.0 kJ•mol -1 •atom -1 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Design considerations for high entropy alloys in advanced nuclear applications

The demanding operating environments of advanced nuclear reactors require the development of new nuclear materials that can withstand their increased physical, chemical, thermal, and radiation-related challenges. High-entropy alloys (HEAs) have shown often-impressive mechanical, thermomechanical, and corrosion-resistant properties, and offer a massive, unexplored compositional space which allows for the targeted development of application-specific materials. Furthermore, although still in a nascent stage, research has shown that HEAs may exhibit unique irradiation tolerance, including reduced defect production and resistance to irradiation-induced swelling and hardening. The mechanisms behind this increased tolerance are not yet well-understood, although the HEA-specific attributes of a complex energy landscape, reduced thermal conductivity, and shift in defect migration energies and pathways provide promising explanations. Here this work assesses the current and future challenges faced by structural nuclear materials, identifying the specific applications in which HEAs may provide a competitive advantage compared to industry-standard materials with the aid of Ashby material selection maps. Considerations are provided for the design of future nuclear HEAs, including calculations of nuclear-relevant properties to assist in the initial down-selection of elements depending on application requirements (e.g., low neutron capture for in-core applications), narrowing the existing compositional space of HEAs to a manageable scope.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Irradiation-induced shift in the thermodynamic stability of phases and the self-healing effect in transformative high entropy alloys

Here, this work investigated Fe 40 Mn 20 Cr 15 Co 20 Si 5 high entropy alloy (CS-HEA), which exhibits transformation induced plasticity (TRIP) from γ-fcc → ε-hcp, as a probable candidate for nuclear applications. CS-HEA is an extensively-explored, low stacking fault energy alloy with superior strength, ductility, fatigue resistance, and corrosion resistance. This study delved into the effect of irradiation on the shift in thermodynamic stability of the phases and thus radiation tolerance. The evolution of phases, lattice parameters, and transformation volume, V γ→ε , were evaluated from X-ray diffraction experiments along with the mechanical response from nanoindentation. The alloy exhibited a recently-proposed novel self-healing mechanism possible due to the TRIP effect to minimize irradiation damage by restraining the γ-fcc → ε-hcp transformation via thermal aid; this self-healing mechanism was confirmed by transmission electron microscopy. The results were corroborated by a negative change in V γ→ε and a low |V γ→ε |, which is an important criterion for recovery of parent γ-fcc phase. Thus, this alloy was deemed a good radiation-tolerant candidate for nuclear application.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural evolution in doped high entropy alloys NiCoFeCr-3X (X=Pd/Al/Cu) under irradiation

Commonly studied equatomic single-phase FCC high entropy alloys based on 3d transition metals like NiCoFeCr do not provide adequate strength and radiation resistance at high doses for nuclear structural applications. In the current study, the major alloying effects like lattice distortion, ordering and clustering tendencies were investigated by adding low concentration of Pd, Al, or Cu respectively to study the doping effects on the ion irradiation response of NiCoFeCr alloy. The alloys were irradiated with 3 MeV Ni 2+ ions at 500 °C to a fluence of 1 × 10 17 /cm 2 at a beam flux of approximately 2.8 × 10 12 ions/cm 2 /s. The microstructural evolution upon irradiation i.e., formation of dislocation networks, radiation induced segregation and precipitation, and void formation were studied in detail. Further, post-irradiation characterization results showed that a Pd addition leads to a high void nucleation rate but controlled void growth, which may be attributed to increased lattice distortion. In Al added HEA, our microstructural analysis indicates that radiation induced ordered L1 2 precipitates do not affect void swelling significantly. Cu addition led to Cu precipitation that drastically suppressed dislocation density and void swelling of the alloy. Additionally, a model was developed to qualitatively describe the trend in void swelling of typical FCC alloys under ion irradiation. This model was able to qualitatively explain the suppression and reappearance of void swelling in ion irradiated alloys that generally occurs near the region with peak implanted ion concentration.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rational design of septenary high-entropy alloy for direct ethanol fuel cells

Promoting C–C bond cleavage of ethanol by a complete 12-electron (12e) ethanol oxidation reaction (EOR) is a grand challenge for the development of highly efficient direct ethanol fuel cells (DEFCs). Most state-of-the-art catalysts only implement the EOR in an incomplete 4e or 2e pathway because of the poisoning of the catalysts by strongly adsorbed CO, leading to the poor output performance and low cell efficiency of DEFCs. Herein, a septenary PtPdFeCoNiSnMn high-entropy alloy (PtPd HEA) with a PtPd-rich surface but super-low platinum group metals loading was developed. We identified and proved the functions of each element in the PtPd HEA. The DEFCs assembled with the PtPd HEA (0.12 mg PtPd ∙cm -2 ) achieved a maximum power density of 0.72 W cm -2 and a durable operation for 1,200 h, which outperforms state-of-the-art catalysts for DEFCs. This work will be a design principle for nanostructured alloy development for renewable energy and sustainability applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Conformal high-entropy oxide coatings enable fast and durable surface oxygen reactions

Developing active and durable air electrodes for efficient oxygen reactions is challenging for protonic ceramic cells (PCCs), especially at temperatures below 550°C. Here, in this study, we report a rationally designed conformal coating with a high-entropy PrNi 0.2 Mn 0.2 Co 0.2 Fe 0.2 Cu 0.2 O 3−δ (PNMCFC) perovskite structure on the surface of a state-of-the-art PrBaCo 2 O 5+δ (PBC) air electrode. The formed hybrid air electrode (PNMCFC-PBC) shows faster surface oxygen kinetics and a more stable phase structure in high-humidity air than the bare PBC electrode. Further density functional theory calculations suggest that the conformal coating mitigates Ba segregation at the interface and improves oxygen-related reactions, enhancing overall stability and electrocatalytic performance. The cells with the developed hybrid electrodes show encouraging electrochemical performance at 550°C: a polarization resistance of 0.72 Ω cm 2 , a peak power density of 1.30 W cm −2 , an electrolysis current density of −1.36 A cm −2 at 1.3 V, and reasonable operating stabilities (∼200 h at 550°C).

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Ethanol-fueled metal supported solid oxide fuel cells with a high entropy alloy internal reforming catalyst

High-performance metal supported solid oxide fuel cells (MS-SOFC) with an integrated high entropy alloy (HEA) internal reforming catalyst (IRC) are demonstrated for transportation applications using ethanol and methanol as fuels. Addition of the HEA IRC dramatically improves cell performance and stability when using ethanol/water blend fuel. Absence of carbon deposition predicted by thermodynamic calculations is confirmed by Raman spectroscopy analysis of posttest anodes. Optimal catalyst processing (deposition technique, loading, firing temperature) and cell operation conditions (flow rates, temperature, fuel compositions) are explored. Infiltrated HEA reforming catalyst provides a highly porous structure and low catalyst loading (6 mg cm –2 ). The designed structure and catalysts achieve small mass transport resistances in the fuel electrode (26.2 s m –1 ) and oxygen electrode (41.6 s m –1 ). The best ethanol concentration (60:40 v% ethanol: water) provides 0.83 W cm –1 at 700 °C, without carbon deposition. The ethanol-fueled MS-SOFC is operated for 500 h, including five thermal cycles. As a result, cell evolution is similar to that reported previously for hydrogen fuel; nickel aggregation and chromia deposition were the major observed changes, and carbon formation can be avoided even after long-term operation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2018

Microband induced plasticity and the temperature dependence of the mechanical properties of a carbon-doped FeNiMnAlCr high entropy alloy

Highlights: • A superior fcc HEA with the strength of 1.5 GPa at the cryogenic condition is developed. • The strengthening mechanisms of HEAs at different temperatures are clarified. • The temperature dependence of MBIP effect is revealed. - Abstract: The uniaxial mechanical properties of the high entropy alloy (HEA) Fe{sub 40.4}Ni{sub 11.3}Mn{sub 34.8}Al{sub 7.5}Cr{sub 6} doped with 1.1 at.% C have been determined for both the as-cast and recrystallized states at temperatures from 77 to 973 K. Very high yield strengths were obtained at 77 K of 928 MPa for the as-cast HEA and 1037 MPa for the recrystallized HEA. The yield strength decreased sharply to 293 K and more slowly to 973 K, where it was ~200 MPa [11] in both conditions. The lattice friction stress, which results from the increase of the Peierls barrier, was the major contributor to the large yield strength at 77 K. On the other hand, the grain boundaries lose their strengthening ability at a high temperature, which largely accounts for the sharp drop in yield strength of the fine-grained (5 μm) recrystallized HEA at 973 K. The elongation to failure was highest at 293 K and 673 K with the lowest values at 77 K. Transmission electron microscopy was used to study the effects of temperature on the deformation mechanisms of the HEAs, especially the temperature dependence of the microband-induced plasticity effect. At temperatures ranging from 77 K to 673 K microbands form in the as-cast HEA, while dislocation clusters were observed in the recrystallized HEA over this temperature range. Only tangled dislocations were found at 973 K for both the as-cast and recrystallized HEA due to thermally-activated deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Phase transformations in body-centered cubic NbxHfZrTi high-entropy alloys

Highlights: • BCC phase stability and phase transformations of NbxHfZrTi HEAs were investigated. • Three types of phase transformations: β → ω, β → α″ and β → α′ in HEAs were observed. • The athermal ω phase in Nb{sub 0.2}HfZrTi HEA leads to a much higher yield strength. • The reversible β → α″ in Nb{sub 0.4}HfZrTi HEA results in a narrow cyclic hysteresis loop. • A sluggish effect of martensitic transformations in complex HEAs is revealed. - Abstract: The stability of body-centered cubic (β) phases and phase transformations of NbxHfZrTi (x = 1, 0.6, 0.4 and 0.2) high-entropy alloys (HEAs) were investigated. Three types of transformations were observed: the β → ω transformation during cooling in Nb0.2 HEA, the deformation-induced β → α″ and β → α′ transformations in Nb0.4 and Nb0.2 HEAs, respectively. This implies that the phonon anomalies, T{sub 1}1/2(110) and L2/3(111), as the origins of phase transformations in simple Ti, Zr and Hf alloys, also exist in composition-complex TiZrHf-based HEAs. However, the very small fraction of deformation-induced α′/α″ martensite in fractured Nb0.4 and Nb0.2 suggests a sluggish effect of transformation as compared with simple β-Ti alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Nanosized precipitates and dislocation networks reinforced C-containing CoCrFeNi high-entropy alloy fabricated by selective laser melting

Highlights: • The SML C-containing CoCrFeNi HEA presents cellular and columnar subgrain structures. • The subgrain boundaries are made of dislocation networks with elements segregations. • The nanosized carbides distribute at grain boundary and subgrain boundaries. • The unique structure of the SLM HEA results in an outstanding yield strength. - Abstract: In this paper, we report a selective laser melted C-containing CoCrFeNi high-entropy alloy (HEA) with unique cellular and columnar subgrain structures. The subgrain boundaries are made of dislocation networks decorated by the segregation of Cr element and nanosized M{sub 23}C{sub 6}-type carbides. Structural characterization of dislocations and dislocation reactions in dislocation networks was conducted using high-resolution transmission electron microscopy. The high strength of the C-containing HEA is attributed to dislocation networks strengthening and nanosized carbides strengthening. These findings can provide a guidance for developing HEAs with superior mechanical properties, particularly high strength.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Friction stir welding of a carbon-doped CoCrFeNiMn high-entropy alloy

Highlights: • Friction stir welding of a CoCrFeNiMn HEA doped with C was successfully obtained. • M{sub 23}C{sub 6} carbides with d≈150 nm form in the HEA due to addition of 0.9 at.% C. • Friction stir welding resulted in a decrease in grain size from 9.2 μm to 4.6 μm. • Smaller grain size and increased fraction of M{sub 23}C{sub 6} increase strength by 84 MPa. - Abstract: Butt-joint seam of a high entropy alloy (HEA) of the CoCrFeNiMn system was successfully obtained by friction stir welding (FSW). The HEA was produced by self-propagating high-temperature synthesis. Along with the principal elements, a small amount (0.9 at.%) of C was added to the alloy. The as-cast alloy was cold rolled and annealed at 900 °C to produce refined microstructure. The structure of the annealed alloy consisted of a recrystallized face-centered cubic matrix with a grain size of 9.2 μm and fine Cr-rich M{sub 23}C{sub 6} carbides. FSW of the HEA resulted in microstructure refinement to d = 4.6 μm in the stir zone. A noticeable rise in strength and some decrease in ductility of the processed alloy in comparison with the initial condition can be associated with the microstructure refinement and some increase in the volume fraction of M{sub 23}C{sub 6} carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Enhanced mechanical properties of carbon-doped FeNiMnAlCr high entropy alloy via hot-rolling

This work demonstrates an improvement in the mechanical performance of the high entropy alloy Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 containing 1.1 at. % carbon (CHEA) by hot-rolling followed by annealing at 1323 K. The microstructure was examined using scanning electron microscopy, electron backscatter diffraction, X-ray diffraction, and transmission electron microscopy. Room-temperature tensile tests were used to assess the alloy's mechanical properties. The presence of dense dislocation walls indicate that the alloy has not fully recrystallized and, moreover, the deformation substructure and the large fraction of Σ3 twin boundaries contribute to the high room temperature yield strength (~523 MPa). Despite the presence of substantial dislocation density, the annealed, hot-rolled CHEA displays an improvement in elongation to fracture (~33%) compared to the negligible ductility (< 2%) observed for the alloy after it has been simply annealed. Finally, the present work shows that hot rolling can produce good strength and ductility in the alloy while establishing the processing conditions necessary for the large-scale manufacture and utilization of its remarkable properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development and characterization of a low-density TiNbZrAlTa refractory high entropy alloy with enhanced compressive strength and plasticity

A new refractory high entropy alloy (RHEA) is designed by combining refractory elements Nb and Ta with Ti, Zr, and Al, resulting in a (TiNbZr) 89 (AlTa) 11 alloy composition with a low-density of 6.0 g/cm 3 . The novel RHEA features a BCC matrix with B2 and Zr 5 Al 3 nano precipitates, exhibiting a compressive yield strength of ~890 MPa and specific yield strength of ~148.3 MPa g -1 cm 3 . Remarkably, the alloy demonstrates excellent compressive plasticity of ~70% at 298 K. As the temperature increases to 873 K, 1073 K, and 1273 K, the yield strength of the RHEA gradually decreases to ~610 MPa, ~ 210 MPa, and ~ 60 MPa, respectively. These results indicate that this novel RHEA showcases a combination of good specific strength and plasticity. Post-compression, B2, and Zr 5 Al 3 phases are observed. In conclusion, the second-phase particles dispersed throughout the grains hinder dislocation motion and contribute to the formation of sub-grain boundaries during hot compression.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The influence of chemical short-range order on the nanoindentation properties of high-entropy alloys prepared via laser powder bed fusion

Chemical short-range order (CSRO) plays an instrumental role in determining the mechanical properties of high-entropy alloys (HEAs). Current methods for controlling CSRO mainly focus on cast HEAs, which can not solve the problem of grain coarsening caused by homogenization treatments. Laser Powder Bed Fusion (LPBF), which has extremely high cooling rates, can suppress compositional segregation, refine grain structures, and achieve low CSRO. This offers a promising avenue for quantitatively controlling CSRO without the need for homogenization treatments. In this study, we investigate the CSRO of HEAs fabricated via LPBF and elucidate their influence on nanoindentation behavior. The results show that, at the low cooling rate, the average size of CSRO is 0.66 nm and they occupy 2.8% of the cross-sectional area, while at high cooling rate, the corresponding values are 0.92 nm and 9.9%, respectively, both of which are significantly smaller than those of cast HEAs. Furthermore, by analyzing samples with different CSROs, we observe that the hardness increases and then decreases with the increase of CSRO, primarily due to the preferential formation of dislocations in regions enriched with Cr-Mn-Ni. With the improvement of CSRO, both the size and quantity of Cr-Mn-Ni rich region gradually increased; subsequently, as multiple Cr-Mn-Ni rich regions tend to merge into one during the CSRO improvement, the size of the Cr-Mn-Ni rich region continued to increase while the quantity gradually decreased; when the size of the Cr-Mn-Ni rich region is moderate and widely dispersed, the dislocation density is higher with much more uniform distributions, which favorably improves nanoindentation hardness.

36 MATERIALS SCIENCE↗
DOE OSTI2024

From phase decomposition to evaporation: A multi-modal evaluation of thermally degraded model lightweight high-entropy alloy

Lightweight high-entropy alloys (LHEAs) have the potential to replace conventional lightweight materials due to their superior mechanical properties and thermal stability. However, the thermal degradation pattern of LHEAs from phase decomposition to evaporation is not clear. We develop a new Al-based dual phase (FCC + HCP) LHEA—AlTi 0.45 CuZn, and further investigate its thermal degradation behavior for potential high-temperature structural applications. Using multimodal advanced characterization techniques such as differential scanning calorimetry/thermogravimetric analysis, scanning/transmission electron microscopy, and synchrotron X-ray diffraction/pair distribution function (XRD/PDF), a sequence of thermal degradation events beyond the thermal phase stability limit—between 250 and 360 °C—is observed. These include phase decomposition at ~360 °C, Zn evaporation at ~750 °C, and LHEA melting at 880 °C which results in ~25% cumulative weight loss. The formation of Al-Ti phase off the AlTi 0.45 CuZn matrix is due to the largest negative mixing enthalpy for Al-Ti than other binary pairs. Similarly, Zn evaporation from AlTi 0.45 CuZn LHEA is due to its faster evaporation rate than other constituent elements. The high-resolution synchrotron XRD and PDF results support the aforementioned observations; in addition, they reveal local atomic arrangements, local strain, and sluggish grain growth in the LHEA. Among other LHEAs of close density range (5.55 ≤ ρ ≤ 5.85 g/cc), the investigated LHEA exhibits outstanding nano-indentation hardness values due to the coupled grain size effect and HCP phase strengthening of the FCC matrix. As the search for LHEAs for lightweight applications grows, this study shows the potential use of AlTi 0.45 CuZn LHEA for structural applications even at elevated temperatures.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Improved creep performance of CoCrFeNi high entropy alloys by Mo addition

The CoCrFeNi family of high entropy alloys has good mechanical and corrosion properties, performing like stainless steels with low yield stresses. They could, however, benefit from hardening methods for structural and high temperature applications. Here, this work investigates the potential for the CoCrFeNi alloy to be hardened with the addition of Mo. A series of CoCrFeNiMo alloys and their CoCrFeNi counterparts were subsequently manufactured at NETL and then mechanically creep tested at 650°C. The alloys were designed to possess a range of stacking fault energies which influence the mechanical properties of the alloys via the motion of their dislocations under stress. Results show that Mo-containing variants have creep rupture lives ranging from 4000 to 8000 hours, i.e., about two orders of magnitude longer than those for Mo-free variants. The significantly improved creep performance of the Mo-containing alloys is due to a combination of solid solution strengthening and precipitation strengthening from µ-phase and carbides.

36 MATERIALS SCIENCE↗