Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Energy density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Computationally Guided Development of Components for High Energy Density Solid-State Lithium-Sulfur Batteries

All electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The most challenging of these technical barriers to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria1. The performance metrics for eVTOL craft, such as specific energy, specific power, and safety, exceed those of electric automobiles by a factor of two to four. Current state-of-the-art (SOA) lithium-ion batteries are incapable of meeting the key performance criteria of energy and safety for eVTOL. Therefore, next generation advanced chemistries and designs must be developed to meet required performance metrics for electric aviation2. Beyond lithium-ion chemistries, such as lithium-sulfur, show promise in their high energy, while limitations exist in their power and cyclability due to low electrical conductivity and high intermediate solubility in organic liquid electrolytes. Several strategies to overcome the low electrical conductivity involve the use of selenium as a dopant in the active sulfur material, along with the incorporation of 2-dimensional electron-conducting holey-graphene to improve the composite cathodes electronic conductivity. Furthermore, combining this chemistry with a solid-electrolyte avoids the components’ dissolution issues3. However, the development of composite solid-state cathodes is non-trivial as several components must be intimately mixed so that the active component has sufficient access to both electrons and lithium ions to undergo full electrochemical conversion. Mathematical modeling of battery components can assist experimental design through a robust and rigorous combination of computational modeling techniques covering multiple length scales. The objective is to leverage modern computational materials methods combined with battery multiphysics tools to develop radically advanced compatible cathode and electrolyte materials, build and test solid state lithium-sulfur cells and packs. A NASA-based cross-organizational team of high-powered experts combined integrated computational predictive modeling, fundamental chemistry analysis, advanced material science, and battery cell development to tackle this very challenging, multidisciplinary problem. This presentation will show a multiscale computational modeling approach that has produced a novel particle dynamics method called Solid Electrolyte Sphere Approximation Model (SESAM). SESAM modeling targets the 1-10 µm scale structures and provides electromechanical and grain interactions for predictive design guidelines for the manufacturing of solid-state components. Parameters such as particle size and volume fraction of the constituent materials were modeled and experimentally fabricated to optimize electrochemical performance through improved microstructure design. Experimental feedback was provided through ionic and electronic conductivity assessment and structural analysis of developed materials and cell components.

battery↗

Inductively Driven, 3D Liner Compression of a Magnetized Plasma to Megabar Energy Densities

To take advantage of the smaller scale, higher density regime of fusion an efficient method for achieving the compressional heating required to reach fusion gain conditions must be found. What is proposed is a more flexible metallic liner compression scheme that minimizes the kinetic energy required to reach fusion. It is believed that it is possible to accomplish this at sub-megajoule energies. This however will require operation at very small scale. To have a realistic hope of inexpensive, repetitive operation, it is essential to have the liner kinetic energy under a megajoule which allows for the survivability of the vacuum and power systems. At small scale the implosion speed must be reasonably fast to maintain the magnetized plasma (FRC) equilibrium during compression. For limited liner kinetic energy, it becomes clear that the thinnest liner imploded to the smallest radius consistent with the requirements for FRC equilibrium lifetime is desired. The proposed work is directed toward accomplishing this goal. Typically an axial (Z) current is employed for liner compression. There are however several advantages to using a θ-pinch coil. With the θ-pinch the liner currents are inductively driven which greatly simplifies the apparatus and vacuum system, and avoids difficulties with the post implosion vacuum integrity. With fractional flux leakage, the foil liner automatically provides for the seed axial compression field. To achieve it with optimal switching techniques, and at an accelerated pace however will require additional funding. This extra expense is well justified as the compression technique that will be enabled by this funding is unique in the ability to implode individual segments of the liner at different times. This is highly advantageous as the liner can be imploded in a manner that maximizes the energy transfer to the FRC. Production of shaped liner implosions for additional axial compression can thus be readily accomplished with the modified power modules. The additional energy and switching capability proposed will thus provide for optimal utilization of the liner energy. The following tasks were outlined for the three year effort: (1) Design and assemble the foil liner compression test structure and chamber including the compression bank and test foils [Year 1]. (2) Perform foil liner compression experiments and obtain performance data over a range on liner dimensions and bank parameters [Year 2]. (3) Carry out compression experiments of the FRC plasma to Megagauss fields and measure key fusion parameters [Year 3]. (4) Develop numerical codes and analyze experimental results, and determine the physics and scaling for future work [Year 1-3]. The principle task of the project was to design and assemble the foil liner FRC formation chamber, the full compression test structure and chamber including the compression bank. This task was completed successfully. The second task was to test foils in the test facility constructed in year one and characterize the performance obtained from liner compression. These experimental measurements were then compared with analytical predictions, and numerical code results. The liner testing was completed and compared with both the analytical results as well as the code work performed with the 3D structural dynamics package of ANSYS Metaphysics®. This code is capable of modeling the dynamic behavior of materials well into the non-linear regime (e.g. a bullet hit plate glass). The liner dynamic behavior was found to be remarkably close to that predicted by the 3D structural dynamics results. Incorporating a code that can also include the magnetics and plasma physics has also made significant progress at the UW. The remaining test bed construction and assembly task is was completed, and the FRC formation and merging experiments were carried out as planned. The liner compression of the FRC to Megagauss fields was not performed due to not obtaining a sufficiently long lived FRC during the final year of the grant. Modifications planned to correct this deficiency included a larger FRC source as well as a much larger liner driver energy storage system. Due to discontinuation of the grant neither of these improvements were carried out.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cherenkov Gamma Ray Detectors on High-Energy-Density Systems

Cherenkov gamma ray detectors are a valuable diagnostic technique for HED systems. Inertial confinement fusion is working towards high gain ignition. Gamma rays from ICF systems can help inform the degradation mechanisms preventing ignition: Carbon ablator is not being degraded, unlike the DT fuel; carbon γ timing can estimate shell energy during bangtime and may suggest hot spot cooling rate; and Cherenkov detectors are also used for high spatial and temporal resolution ICF mix studies on OMEGA. Cherenkov systems also inform energy spectrum of radiographic sources: ARC laser and Mercury pulsed power machine.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Rechargeable Magnesium Batteries: Low-Cost Rechargeable Magnesium Batteries with High Energy Density

BEEST Project: Pellion Technologies is developing rechargeable magnesium batteries that would enable an EV to travel 3 times farther than it could using Li-ion batteries. Prototype magnesium batteries demonstrate excellent electrochemical behavior; delivering thousands of charge cycles with very little fade. Nevertheless, these prototypes have always stored too little energy to be commercially viable. Pellion Technologies is working to overcome this challenge by rapidly screening potential storage materials using proprietary, high-throughput computer models. To date, 12,000 materials have been identified and analyzed. The resulting best materials have been electrochemically tested, yielding several very promising candidates.

ARPA-E↗

Radiation from Ag high energy density Z-pinch plasmas and applications to lasing

Silver (Ag) wire arrays were recently introduced as efficient x-ray radiators and have been shown to create L-shell plasmas that have the highest electron temperature (>1.8 keV) observed on the Zebra generator so far and upwards of 30 kJ of energy output. In this paper, results of single planar wire arrays and double planar wire arrays of Ag and mixed Ag and Al that were tested on the UNR Zebra generator are presented and compared. To further understand how L-shell Ag plasma evolves in time, a time-gated x-ray spectrometer was designed and fielded, which has a spectral range of approximately 3.5–5.0 Å. With this, L-shell Ag as well as cold L{sub α} and L{sub β} Ag lines was captured and analyzed along with photoconducting diode (PCD) signals (>0.8 keV). Along with PCD signals, other signals, such as filtered XRD (>0.2 keV) and Si-diodes (SiD) (>9 keV), are analyzed covering a broad range of energies from a few eV to greater than 53 keV. The observation and analysis of cold L{sub α} and L{sub β} lines show possible correlations with electron beams and SiD signals. Recently, an interesting issue regarding these Ag plasmas is whether lasing occurs in the Ne-like soft x-ray range, and if so, at what gains? To help answer this question, a non-local thermodynamic equilibrium (LTE) kinetic model was utilized to calculate theoretical lasing gains. It is shown that the Ag L-shell plasma conditions produced on the Zebra generator at 1.7 maximum current may be adequate to produce gains as high as 6 cm{sup −1} for various 3p → 3s transitions. Other potential lasing transitions, including higher Rydberg states, are also included in detail. The overall importance of Ag wire arrays and plasmas is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Structural Changes in a High-Energy Density VO 2 F Cathode upon Heating and Li Cycling

Structural changes in VO 2 F, which allow two-electron transfer during electrochemical Li cycling, were investigated in this work. This compound adopts a rhombohedral structure, space group $R\overline{3}c$, with O and F sharing one site, and was synthesized by high-energy ball-milling. The thermal stability of VO 2 F, which is related to the battery safety, is studied by in situ XRD upon heating and by thermal gravimetric analysis. VO 2 F is found to be stable up to 160 °C under inert atmosphere; above this temperature, it converts into vanadium oxide with fluorine loss. The structure evolution upon lithium cycling was studied by ex situ X-ray diffraction and absorption techniques. The results show that lithiation of VO 2 F goes through a solid-solution reaction, and the rhombohedral structure is preserved if no more than one lithium ion is intercalated. Upon a second Li insertion, an irreversible transition to a rock-salt structure occurs. We show using first-principles calculations that this irreversible transformation can be explained by an asymmetric energetic preference between the rhombohedral and rock-salt forms of Li x VO 2 F, which result in large thermodynamic driving forces to convert to the rock-salt structure at x > 1 and relatively small thermodynamic driving forces to convert back to the rhombohedral structure when delithiating to x < 1.

25 ENERGY STORAGE↗

Generation and Control of Self-Organized Nonlinear Kinetic Structures in High Energy Density Plasmas in the Presence of Intense Magnetic Fields and Ultrashort Laser Pulses

In the project we investigated mechanisms to sculpt phase space by controlling plasma instabilities. We found that linear theory, which applies in the initial growth phase of an instability, allows for initial conditions that can suppress instabilities. This provides a possible mechanism to release the energy available to an instability on demand. We developed various computational techniques that can reduce computational cost of simulations while maintaining or improving physical fidelity. We considered the Buneman instability in the presence of a ponderomotively driven plasma wave to examine the interplay between an instability and steady-state plasma response.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Radiation sources with planar wire arrays and planar foils for inertial confinement fusion and high energy density physics research

This article reports on the joint success of two independent lines of research, each of them being a multi-year international effort. One of these is the development of innovative sources, such as planar wire arrays (PWAs). PWAs turned out to be a prolific radiator, which act mainly as a resistor, even though the physical mechanism of efficient magnetic energy conversion into radiation still remains unclear. We review the results of our extensive studies of PWAs. We also report the new results of the experimental comparison PWAs with planar foil liners (another promising alternative to wire array loads at multi-mega-ampere generators). Pioneered at UNR, the PWA Z-pinch loads have later been tested at the Sandia National Laboratories (SNL) on the Saturn generator, on GIT-12 machine in Russia, and on the QiangGuang-1 generator in China, always successfully. Another of these is the drastic improvement in energy efficiency of pulsed-power systems, which started in early 1980s with Zucker's experiments at Naval Research Laboratory (NRL). Successful continuation of this approach was the Load Current Multiplier (LCM) proposed by Chuvatin in collaboration with Rudakov and Weber from NRL. The 100 ns LCM was integrated into the Zebra generator, which almost doubled the plasma load current, from 0.9 to 1.7 MA. The two above-mentioned innovative approaches were used in combination to produce a new compact hohlraum radiation source for ICF, as jointly proposed by SNL and UNR [Jones et al., Phys. Rev. Lett. 104, 125001 (2010)]. The first successful proof-of-the-principle experimental implementation of new hohlraum concept at university-scale generator Zebra/LCM is demonstrated. A numerical simulation capability with VisRaD code (from PRISM Co.) established at UNR allowed for the study of hohlraum coupling physics and provides the possibility of optimization of a new hohlraum. Future studies are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Global properties of nuclei at finite-temperature within the covariant energy density functional theory

In stellar environments nuclei appear at finite temperatures, becoming extremely hot in core-collapse supernovae and neutron-star mergers. However, due to theoretical and computational complexity, most model calculations of nuclear properties are performed at zero temperature, while those existing at finite temperatures are limited only to selected regions of the nuclide chart. In this study we perform the global calculation of nuclear properties for even-even 8 ≤ Z ≤ 104 nuclei at temperatures in range 0 ≤ T ≤ 2 MeV. Calculations are based on the finite-temperature relativistic Hartree-Bogoliubov model supplemented by the Bonche-Levit-Vautherin vapor subtraction procedure. We find that near the neutron-drip line the continuum states have significant contribution already at moderate temperature T ≈ 1 MeV, thus emphasizing the necessity of the vapor subtraction procedure. Results include neutron emission lifetimes, quadrupole deformations, neutron-skin thickness, proton and neutron pairing gaps, entropy and excitation energy. Up to the temperature T ≈ 1 MeV, the nuclear landscape is influenced only moderately by the finite-temperature effects, mainly by reducing the pairing correlations. Here, as the temperature increases further, the effects on nuclear structures become pronounced, reducing both the deformations and the shell effects.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Using distributions to understand neutron and x-ray production in ICF ignition capsules and other high energy density plasmas

Here this paper describes how x-ray and neutron distribution functions can be useful tools to visualize the conditions measured in many types of plasma physics experiments. In particular, we model a standard inertial confinement fusion ignition capsule that consists of a Si doped plastic ablator surrounding a layer of deuterium–tritium (DT) ice as the yield varies from 18 kJ to 16.7 MJ and use the distribution functions to show that neutrons and high energy x rays (15 keV) are produced under similar conditions when the yield is low. However, as the capsule starts to support a propagating burn due to alpha heating, the x rays and neutrons are produced under somewhat different conditions in different parts of the plasma. In particular, the x-ray production takes place mainly in the hot plastic ablator for the full yield ignition capsule under quite different plasma conditions from the DT region producing the 14 MeV neutrons, which results in x-ray images with larger radii than the corresponding neutron images. These same distribution functions can be applied to many other plasma physics experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Developing A New NG Super-Absorbent Polymer (NG-SAP) for a Practical NG Storage System with Low Pressure, Ambient Temperature, and High Energy Density

This R&D project proposed a systematical study to develop a new class of NG super-absorbent polymer (NG-SAP) with the objective to achieve similar CNG volumetric storage level ~250 cm 3 -STP/cm 3 and fast sorption-desorption kinetics at ambient temperature but lower operational pressure (<100 bar). We suggested two consecutive research phases, including (i) a systematical investigation of various polymer systems to identify the suitable classes that can exhibit methane (C1) binding energy in the range of 20-25 kJ/mol and then (ii) focusing on the potential class polymers to identify the specific structure and morphology that can achieve the project objective.In first research phase (1st year), the major tasks included design and synthesis of several representative polymers with various structure attributes, examining their molecular structures, pore morphology, and BET surface area as the prepared samples, and then studying their C1 binding energy and sorption capacity.

03 NATURAL GAS↗