Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Contact Resistance of Carbon–Li x (Ni,Mn,Co)O 2 Interfaces

Abstract Electronic resistance in lithium‐ion battery positive electrodes is typically attributed to the bulk resistance of the active material and the network resistance of the carbon additive. Expected overpotentials from these bulk components are minimal relative to that from charge‐transfer resistance. However, literature reports show that cell overpotentials are often much more sensitive to conductive additives than the expected level from bulk or percolating‐network transport. This discrepancy motivated a detailed examination of the contact resistance between the active material and conductive additive. The contact and bulk resistances are simultaneously measured using dense bar samples of lithium‐layered oxides (Li x Ni 1 /3 Mn 1/3 Co 1/3 O 2 and Li x Ni 0.5 Mn 0.3 Co 0.2 O 2 ) in contact with carbon black. It is found that the contact resistance dominates the overall electronic resistance when the length scale is smaller than millimeters; after correcting for contact effects, bulk conductivity of layered oxides is determined to be orders‐of‐magnitude higher than previously reported. In porous electrodes, it is found from three‐electrode electrochemical impedance spectroscopy that the carbon content most heavily influences the low‐frequency regime (≈0.01 Hz), as opposed to the high frequency (>10 3 Hz) regime expected from electronic percolating properties. Constriction effects within the layered oxide are identified as the dominant mechanism for contact resistance and its implication is investigated for porous electrodes.

Kuo, Jimmy Jiahong↗
NASA NTRS1951

Effect of Surface Finish on Fatigue Properties at Elevated Temperatures I : Low-carbon N-155 with Grain Size of A.S.T.M. 1

Effect of three surface finishes of roughness 4 to 5, 20 to 25, and 70 to 80 micro inches rms on fatigue properties were determined for low-carbon N-155 alloy of grain size A.S.T.M. 1 at temperatures of 80 , 1000, 1350, and 1500 F. The fatigue properties for the various finishes differed appreciably at room temperature; however, after short periods at 1000 F and for all periods investigated at temperatures above 1000 F, the specimen finishes had the same fatigue strength. It was concluded that the primary cause of the difference in room-temperature strength was due to compressive stresses set up in the surface and that at elevated temperatures these compressive stresses were relieved by annealing. Apparently, roughness alone did not significantly affect fatigue strength.

Ferguson, Robert R↗
NASA NTRS1989

Thermoplastic matrix composites - Finite-element analysis of mode I and mode II failure specimens

A finite-element analysis was conducted to evaluate the stress distributions within mode I and mode II failure specimens, assuming both isotropic and orthotropic elastic material properties. The effects of anisotropy on both the magnitude and the location of the highest stress concentration at the vicinity of the crack tip are significant. The results from modeling realistic blunt crack tip geometry and resin-rich zones imply that local variations in the microstructure strongly influence the stress state near the crack tip and therefore the measured fracture properties. In addition, the features of a viscoelastic model for thermoplastic matrices are described. This model will be used in future investigations of matrix-dominated failure phenomena.

Bankert, Ray J.↗
NASA NTRS1981

The effect of elastomer chain length on properties of silicone-modified polyimide adhesives

A series of polyimides containing silicone elastomers was synthesized in order to study the effects of the elastomer chain length on polymer properties. The elastomer with repeat units varying from n=10 to 105 was chemically reacted into the backbone of an addition polyimide oligomer via reactive aromatic amine groups. Glass transition temperatures of the elastomer and polyimide phases were observed by torsional braid analysis. The elastomer-modified polyimides were tested as adhesives for bonding titanium in order to determine their potential for aerospace applications. Adhesive lap shear tests were performed before and after aging bonded specimens at elevated temperatures.

St.clair, A. K.↗
DOE OSTI2020

Effect of oxidation post treatments on TiO 2 coating manufactured using reactive very low-pressure plasma spraying (R-VLPPS)

TiO 2 coatings manufactured using reactive very low-pressure plasma spraying (R-VLPPS) were analyzed in different regions related to their position compared to the plasma flame. For that, a screen was used in order to hide an area of the substrate from the direct plasma flux. The coating morphology changed from quasi lamellar structure to highly vapor structure and coatings exhibited obvious modifications in terms of phases and mechanical properties. The effect of oxidation post treatment on the as sprayed coating was then studied by selecting two methods: in situ oxidation post treatment and classical thermal treatment. The two post treatments provided an increase of the main rutile phase and a decrease of both the size and the contents of porosity simultaneously.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Effects of turbulence mixing, variable properties, and vaporization on spray droplet combustion

Combustion of liquid fuels in the form of spray droplets is simulated numerically. Various vaporization models are examined as to their performance in finite element calculations involving a turbulent flow field. The Eulerian coordinate for the gas and Lagrangian coordinate for the liquid spray droplets are coupled through source terms being updated in the equations of continuity, momentum, and energy. The k-epsilon and modified eddy breakup models are used for simulating turbulent spray combustion flow field. Numerical results for the droplet trajectories, droplet heating, recirculation characteristics, and effects of evaporation models are evaluated. It is also shown that the finite element method is advantageous in dealing with complex geometries, complex boundary conditions, adaptive unstructured grids.

Kim, Y. M.↗
DOE OSTI2022

Correction to: Investigating the rheology of fluidized and non-fluidized gas-particle beds: implications for the dynamics of geophysical flows and substrate entrainment

We report natural geophysical mass flows are among the most complex granular systems and their dynamics are often modified by the presence of an interstitial fluid. Prediction of their runout requires the development of models estimating the solid stresses in these hazardous currents wherein excess pore-fluid pressure can develop. We use discrete element modelling (DEM-CFD) with a Coarse-Graining post-processing technique (CG) to investigate the rheology of unsteady gas-particle fluidized to non-fluidized granular beds placed on horizontal and inclined planes. Similar to fluidized beds immersed in viscous fluids, the effective friction coefficient of air-fluidized beds can be defined as a function of the classic μ(I)-rheology and the non-dimensional fluid or solid pressure to explain the failure and dynamics of granular flows with excess pore pressure on inclines. However, dilation imposed by fluid drag and particle collisions in gas-particle fluidized beds can drastically change its effective frictional properties. In contrast with the common assumption in water-particle flows that granular temperature is negligible, in our gas-particle simulations, the contribution of the velocity fluctuations to the stress tensor is significant. Hence, the shear stress is found to be non-zero even when the flow is fully fluidized in the inertial regime. These results suggest the need to better understand velocity fluctuations to predict the effective viscosity of sheared fluidized mixtures and are relevant for many applications. Notably, a unified approach is useful for many geophysical flows that encompass a range of fluidization conditions in a single flow such as pyroclastic density currents and snow avalanches.

58 GEOSCIENCES↗
NASA NTRS1978

Interdisciplinary research and development on the effects of the nature and properties of ceramic materials in the design of advanced structural components

An educational development and supportive research program on ceramic materials established to advance design methodology, improve materials, and develop engineers knowledgable in design with and use of high performance ceramic materials is described. Emphasis is on the structures and related materials problems in a ceramic turbine engine, but applications in coal gasification, solar conversion, and magnetohydrodynamic technologies are considered. Progress of various research projects in the areas of new materials, processing, characterization, and nondestructive testing is reported. Fracture toughness determination, extended X-ray absorption fine structure measurements, and grain boundary effects in beta-alumina are among the topics covered.

Source record↗
NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ®†† in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi- isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non- destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Laser↗
NASA NTRSDate not supplied

Laser Angle of Incidence Effects on in-Situ Consolidation of Automated Fiber Placement of Polyaryletherketone Composites

NASA and Electroimpact, Inc. ® in conjunction with other U.S. industry partners are performing research as a part of the NASA High-rate Composites for Aircraft Manufacturing (HiCAM) Project to fabricate thermoplastic panels using automated fiber placement (AFP) to increase manufacturing rates of aircraft structural composites. This work focuses on evaluating the in-situ consolidation AFP of thermoplastics (ICAT) process. Previous studies of the ICAT process using semi-crystalline, polyaryletherketone (PAEK) slit-tape have resulted in an adequate degree of intimate contact between plies; however, the resulting interlaminar strength have been less than laminates fabricated in an autoclave. To improve these properties, the effect of reducing the laser angle of incidence (AoI) during placement to increase the degree of auto-hesion was evaluated. The AoI of the laser assisted AFP head was varied between 12° and 16° to fabricate multiple quasi-isotropic and unidirectional test panels. Physics-based thermal models developed at the NASA Langley Research Center were utilized to predict the temperature profile. Laminate processing temperature was measured experimentally, and panel quality was evaluated by both non-destructive evaluation (NDE) as well as destructively by photo-microscopy. The effect on interlaminar strength was determined by short beam strength testing. Test results of carbon fiber laminates fabricated by ICAT using polyetheretherketone (PEEK), polyetherketoneketone (PEKK), and low-melt polyaryletherketone (LM-PAEK) at various laser angles of incidence, placement temperatures and placement speeds are presented.

Thermoplastic Composites↗
DOE OSTI2021

Computational Evaluation of Thermal Response of Open-Cell Foam With Circular Pore (Computional Evaluation of Thermal Response of Open-Cell Foam with Circular Pore)

The evaluation of effective material properties in heterogeneous materials (e.g., composites or multicomponent structures) critically relevant to a wide spectrum of applications, including nuclear power, electronic packaging, flame retardants, hypersonics, and gas turbine power. The work described in this paper is centered around the numerical assessment of the thermal behavior of porous materials obtained from finite element thermal modeling and simulation. Here, two-dimensional, steady state analyses were performed on unit cells with centered, circular pores using a second order accurate Galerkin finite element method (FEM). The effective thermal conductivities of the porous systems were examined, encompassing a range of porosities from 4.9% to 60.1%. The geometries of the models were generated based on ordered circular pores for each modeled porosity level. The system response quantity (SRQ) under investigation was the dimensionless effective thermal conductivity across the unit cell. The dimensionless effective thermal conductivity was compared across all simulated cases, producing a trend between porosity and effective thermal conductivity. In the presented investigation, the method of manufactured solutions (MMS) was used to perform code verification, and the grid convergence index (GCI) was employed to estimate discretization uncertainty as solution verification. Code verification concluded an approximately second order accurate Galerkin FEM solver. It was found that the introduction of porosity to the unit cell material structure reduces effective thermal conductivity, as anticipated. Numerical results obtained in this study are compared to an analytical solution and to a sample of empirical data.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Establishing an acoustic-property relationship in laser powder bed fusion with machine learning

Quality control of Laser Powder Bed Fusion (PBF-LB) additively manufactured parts is an important hurdle inhibiting the technology’s use structural applications. Acoustic monitoring of the laser powder bed fusion process can detect defects in-situ that are known to degrade mechanical properties. However, processing-structure-property (PSP) relationships are required to extrapolate from detected defects to part performance. Here, this study explores how acoustics may be a suitable signature linking processing conditions to properties, thus effectively substituting for structure in the PSP relationship. Establishing such a relationship would enable a part’s mechanical performance to be directly predicted from its acoustic signature, reducing the need for destructive testing or microstructural analysis to ensure a part will meet performance requirements. One hundred CoCrFeMnNi high entropy alloy tensile bars were printed across 13 process conditions in a series of 6 prints. The acoustic signatures of these tensile bars were used to train machine learning models to predict each part’s mechanical properties. By using both process information and acoustic information to predict mechanical properties, yield strength was predicted 18% more accurately and ductility to failure was predicted 10% more accurately than is achieved when using duplicate parts to predict part performance. Finally, individual acoustic frequencies were investigated to determine why acoustic signatures improve mechanical property predictions and the potential physical origins of these signatures. This work demonstrates how blending acoustics, process information, and machine learning can provide in-situ diagnostics of mechanical properties and improve the reliability of the PBF-LB process.

Acoustic emission↗
DOE OSTI2021

Elucidating the structural properties and reversible regional texture effect of GdB 6 under high pressure

As hard and refractory materials with high chemical resistance and mechanical strength, lanthanide hexaborides (LnB 6 ) have attracted much attention. Among the family of LnB 6 , gadolinium hexaboride (GdB 6 ) occupies a special position due to the half-filled 4f shell of Gd. Here, using in situ synchrotron radiation angle-dispersive X-ray diffraction in a diamond anvil cell at room temperature, the structural stability and compression behavior of GdB 6 are investigated extensively, GdB 6 is observed to be structurally stable up to 73 GPa, and the bulk modulus of 177 GPa is obtained under hydrostatic compression. In this paper, an interesting observation of pressure-induced spotty diffraction rings of GdB6 is reported, its formation mechanism can be well described by the reversible regional texture effect, which highlights the rearrangement of crystal grains under high pressure. The rearrangement mechanism has been well explained by investigating the pressure dependence of full width at half maximum, macro-differential stress and grain size. Collective grain rotation behavior motivated by stress difference is critical for the rearrangement process, the strong isotropy and strong stability of GdB 6 structure also provide necessary conditions for high-pressure grain rotation behavior. These results will help to promote the understanding of high-pressure structural properties of GdB 6 , and provide novel insights on the high-pressure grain behavior in hard materials with strong isotropy and three-dimensional skeleton constituted of strong covalent bonds.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Stochastic minibatch approach to the ptychographic iterative engine

The ptychographic iterative engine (PIE) is a widely used algorithm that enables phase retrieval at nanometer-scale resolution over a wide range of imaging experiment configurations. By analyzing diffraction intensities from multiple scanning locations where a probing wavefield interacts with a sample, the algorithm solves a difficult optimization problem with constraints derived from the experimental geometry as well as sample properties. The effectiveness at which this optimization problem is solved is highly dependent on the ordering in which we use the measured diffraction intensities in the algorithm, and random ordering is widely used due to the limited ability to escape from stagnation in poor-quality local solutions. In this study, we introduce an extension to the PIE algorithm that uses ideas popularized in recent machine learning training methods, in this case minibatch stochastic gradient descent. Our results demonstrate that these new techniques significantly improve the convergence properties of the PIE numerical optimization problem.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Pressure Effects on the Electronic and Optical Properties in Low-Dimensional Metal Halide Perovskites

Metal halide perovskites have shown enormous potential in perovskite solar cells and light-emitting diodes and made unprecedented progress in the past decade. Additionally, pressure engineering as an effective technique can systematically modify the electronic structures and physical properties of functional materials. Low-dimensional metal halide perovskites (0D, 1D, and 2D) with a variety of compositions have soft lattices that allow pressure to drastically modulate their structures and properties. High-pressure investigations have obtained a comprehensive understanding of their structure–property relationships. Simultaneously, discoveries of novel pressure-driven properties, such as metallization and partially retained band gap narrowing have contributed significantly to the further development of such materials. In this work, we mainly highlight the effect of pressure on the properties and structures of low-dimensional metal halide perovskites, which is essential for designing new perovskite materials and advancing applications.

36 MATERIALS SCIENCE↗