Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Edge Computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Numerical analysis of a NACA0012 airfoil with leading edge ice accretions

Analysis of a NACA0012 airfoil with leading edge ice has been performed using a Navier-Stokes code coupled with a grid generation code. The computed results were compared to experimental information obtained for an airfoil with a well defined artificial ice shape. The computations were performed at angles of attack ranging from zero to ten degrees. This range is sufficient to show the development of the separation bubble aft of the ice shape on both the upper and lower surfaces. Velocity profile plots in the separation bubble are examined in order to determine if recirculation patterns are predicted properly and if separation and reattachment points are found within the resolution of the experimental information. Also, the massive separation near the point of stall is examined in order to more accurately evaluate the lift coefficient curve in that region. Lift, drag, and moment coefficients are computed and compared to experiment.

Potapczuk, Mark G.↗
NASA NTRS1990

Heat transfer measurements from a NACA 0012 airfoil in flight and in the NASA Lewis icing research tunnel

Local heat transfer coefficients from a smooth and roughened NACA 0012 airfoil were measured using a steady state heat flux method. Heat transfer measurements on the specially constructed 0.533 meter chord airfoil were made both in flight on the NASA Lewis Twin Otter Research Aircraft and in the NASA Lewis Icing Research Tunnel (IRT). Roughness was obtained by the attachment of small, 2 mm diameter, hemispheres of uniform size to the airfoil surface in four distinct patterns. The flight data was taken for the smooth and roughened airfoil at various Reynolds numbers based on chord in the range of 1.24x10(exp 6) to 2.50x10(exp 6) and at various angles of attack up to 4 degrees. During these flight tests the free stream velocity turbulence intensity was found to be very low (less than 0.1 percent). The wind tunnel data was taken in the Reynolds number range of 1.20x10(exp 6) to 4.52x10(exp 6) and at angles of attack from -4 degrees to +8 degrees. The turbulence intensity in the IRT was 0.5 to 0.7 percent with the cloud making spray off. Results for both the flight and tunnel tests are presented as Frossling number based on chord versus position on the airfoil surface for various roughnesses and angle of attack. A table of power law curve fits of Nusselt number as a function of Reynolds number is also provided. The higher level of turbulence in the IRT versus flight had little effect on heat transfer for the lower Reynolds numbers but caused a moderate increase in heat transfer at the higher Reynolds numbers. Turning on the cloud making spray air in the IRT did not alter the heat transfer. Roughness generally increased the heat transfer by locally disturbing the boundary layer flow. Finally, the present data was not only compared with previous airfoil data where applicable, but also with leading edge cylinder and flat plate heat transfer values which are often used to estimate airfoil heat transfer in computer codes.

Poinsatte, Philip E.↗
NASA NTRS1990

Shock interference studies on a circular cylinder at Mach 16

This paper presents the results of a computational study on the shock interference problems on a cylindrical body typical of an engine inlet cowl leading edge at a nominal Mach number of 16. The two-dimensional Navier-Stokes equations are solved assuming the flow to be in chemical and thermal equilibrium and using a finite element method. The algorithm employs a cell-centered fully implicit upwind scheme. Adaptively generated unstructured meshes of triangles and quadrilaterals are employed. Under certain conditions the finite element code resulted in oscillatory solutions for shock interference at Mach 16. Some of the causes of the unsteady behavior are identified, and to the extent possible, such situations are avoided in the present application. Two shock interference conditions involving a Type IV (supersonic jet) and a Type III (attaching shear layer) are solved. The results are compared with available experimental data and reasonable agreement is observed. A semi-empirical method is also used to estimate the maximum surface heat flux and static pressure.

Prabhu, Ramadas K.↗
NASA NTRS1991

Review of boundary layer transition flight data on the Space Shuttle Orbiter

Both thermocouple data and flight-derived axial force coefficients have been used to determine the freestream flight conditions at which boundary-layer transition occurs on the windward surface of the Space Shuttle Orbiter during reentry. Boundary-layer-edge local flow conditions corresponding to transition at thermocouple locations on the Orbiter windward centerline have also been computed. Tables of the freestream conditions and the local flow conditions at transition are included. Transition occurred over a freestream Mach number range of 6.6 to 17.9 and Reynolds number range of (2.3-9.6) x 10 to the 6th. The roughness state of the Orbiter vehicles is also discussed and correlated to the occurrence of transition. Using the distributed roughness transition correlation of Bertin et al. (1982), a flight-derived roughness height of 0.061 inches was obtained. An average flight-derived roughness height of 0.103 inches for a discrete roughness element in the nose region was obtained using the correlation of Van Driest and Blumer (1968).

Bouslog, S. A.↗
NASA NTRS1991

Heat transfer measurements from a smooth NACA 0012 airfoil

Local convective heat transfer coefficients were measured from a smooth NACA 0012 airfoil having a chord length of 0.533 m. Flight data were taken for the smooth airfoil at Reynolds numbers based on chord in the range 1.24 to 2.50 million and at various angles of attack up to 4 deg. During these flight tests, the freestream velocity turbulence intensity was found to be very low. Wind tunnel data were acquired in the Reynolds number range 1.20 to 4.52 million and at angles of attack from -4 to +8 deg. The turbulence intensity in the IRT was 0.5-0.7 percent with the cloud-generating sprays off. A direct comparison between the results obtained in flight and in the IRT showed that the higher level of turbulence intensity in the IRT had little effect on the heat transfer for the lower Reynolds numbers but caused a moderate increase in heat transfer at the higher Reynolds numbers. Turning on the cloud-generating spray nozzle atomizing air in the IRT did not alter the heat transfer. The present data were compared with leading-edge cylinder and flat plate heat transfer correlations that are often used to estimate airfoil heat transfer in computer codes.

Poinsatte, Philip E.↗
NASA NTRS1992

Mechanics of anisotropic plates and shells - A new look at an old subject

A number of aspects of the mechanics of anisotropic plates and shells are discussed. The topics covered include computational models of anisotropic plates and shells, consequences of anisotropy on deformation couplings, symmetry types, stress concentrations and edge effects, and importance of transverse shear deformation; recent applications and recent advances in the modeling and analysis of anisotropic plates and shells; and new research directions.

Noor, A. K.↗
NASA NTRS1993

Image analysis by integration of disparate information

Image analysis often starts with some preliminary segmentation which provides a representation of the scene needed for further interpretation. Segmentation can be performed in several ways, which are categorized as pixel based, edge-based, and region-based. Each of these approaches are affected differently by various factors, and the final result may be improved by integrating several or all of these methods, thus taking advantage of their complementary nature. In this paper, we propose an approach that integrates pixel-based and edge-based results by utilizing an iterative relaxation technique. This approach has been implemented on a massively parallel computer and tested on some remotely sensed imagery from the Landsat-Thematic Mapper (TM) sensor.

Lemoigne, Jacqueline↗
NASA NTRS1998

Flow Applications of the Least Squares Finite Element Method

The main thrust of the effort has been towards the development, analysis and implementation of the least-squares finite element method (LSFEM) for fluid dynamics and electromagnetics applications. In the past year, there were four major accomplishments: 1) special treatments in computational fluid dynamics and computational electromagnetics, such as upwinding, numerical dissipation, staggered grid, non-equal order elements, operator splitting and preconditioning, edge elements, and vector potential are unnecessary; 2) the analysis of the LSFEM for most partial differential equations can be based on the bounded inverse theorem; 3) the finite difference and finite volume algorithms solve only two Maxwell equations and ignore the divergence equations; and 4) the first numerical simulation of three-dimensional Marangoni-Benard convection was performed using the LSFEM.

Jiang, Bo-Nan↗
NASA NTRS2001

Demonstration of a Segment Alignment Maintenance System on a Seven-Segment Sub-Array of the Hobby-Eberly Telescope

NASA's Marshall Space Flight Center, in collaboration with Blue Line Engineering of Colorado Springs, Colorado, is developing a Segment Alignment Maintenance System (SAMS) for McDonald Observatory's Hobby-Eberly Telescope (HET). The SAMS shall sense motions of the 91 primary mirror segments and send corrections to HET's primary mirror controller as the mirror segments misalign due to thermo-elastic deformations of the mirror support structure. The SAMS consists of inductive edge sensors supplemented by inclinometers for global radius of curvature sensing. All measurements are sent to the SAMS computer where mirror motion corrections are calculated. In October 2000, a prototype SAMS was installed on a seven-segment cluster of the HET. Subsequent testing has shown that the SAMS concept and architecture are a viable practical approach to maintaining HET's primary mirror figure, or the figure of any large segmented telescope. This paper gives a functional description of the SAMS sub-array components and presents test data to characterize the performance of the sub-array SAMS.

Rakoczy, John↗
NASA NTRS1998

Geometry Modeling and Grid Generation for Design and Optimization

Geometry modeling and grid generation (GMGG) have played and will continue to play an important role in computational aerosciences. During the past two decades, tremendous progress has occurred in GMGG; however, GMGG is still the biggest bottleneck to routine applications for complicated Computational Fluid Dynamics (CFD) and Computational Structures Mechanics (CSM) models for analysis, design, and optimization. We are still far from incorporating GMGG tools in a design and optimization environment for complicated configurations. It is still a challenging task to parameterize an existing model in today's Computer-Aided Design (CAD) systems, and the models created are not always good enough for automatic grid generation tools. Designers may believe their models are complete and accurate, but unseen imperfections (e.g., gaps, unwanted wiggles, free edges, slivers, and transition cracks) often cause problems in gridding for CSM and CFD. Despite many advances in grid generation, the process is still the most labor-intensive and time-consuming part of the computational aerosciences for analysis, design, and optimization. In an ideal design environment, a design engineer would use a parametric model to evaluate alternative designs effortlessly and optimize an existing design for a new set of design objectives and constraints. For this ideal environment to be realized, the GMGG tools must have the following characteristics: (1) be automated, (2) provide consistent geometry across all disciplines, (3) be parametric, and (4) provide sensitivity derivatives. This paper will review the status of GMGG for analysis, design, and optimization processes, and it will focus on some emerging ideas that will advance the GMGG toward the ideal design environment.

Samareh, Jamshid A.↗
NASA NTRS2011

Gas Generator Feedline Orifice Sizing Methodology: Effects of Unsteadiness and Non-Axisymmetric Flow

Engine LH2 and LO2 gas generator feed assemblies were modeled with computational fluid dynamics (CFD) methods at 100% rated power level, using on-center square- and round-edge orifices. The purpose of the orifices is to regulate the flow of fuel and oxidizer to the gas generator, enabling optimal power supply to the turbine and pump assemblies. The unsteady Reynolds-Averaged Navier-Stokes equations were solved on unstructured grids at second-order spatial and temporal accuracy. The LO2 model was validated against published experimental data and semi-empirical relationships for thin-plate orifices over a range of Reynolds numbers. Predictions for the LO2 square- and round-edge orifices precisely match experiment and semi-empirical formulas, despite complex feedline geometry whereby a portion of the flow from the engine main feedlines travels at a right-angle through a smaller-diameter pipe containing the orifice. Predictions for LH2 square- and round-edge orifice designs match experiment and semi-empirical formulas to varying degrees depending on the semi-empirical formula being evaluated. LO2 mass flow rate through the square-edge orifice is predicted to be 25 percent less than the flow rate budgeted in the original engine balance, which was subsequently modified. LH2 mass flow rate through the square-edge orifice is predicted to be 5 percent greater than the flow rate budgeted in the engine balance. Since CFD predictions for LO2 and LH2 square-edge orifice pressure loss coefficients, K, both agree with published data, the equation for K has been used to define a procedure for orifice sizing.

Rothermel, Jeffry↗
NASA NTRSDate not supplied

arcjetCV: automating recession extraction from video

Arc jet Computer Vision (arcjetCV)[1][2] is a software application built to automate time-resolved recession tracking of edges in test videos, specifically for tracking material recession and the shock-material standoff. This provides a new capability to resolve and validate new physics associated with non-linear processes and an essential step to reduce testing, modeling, and validation uncertainties for heatshield material performance. ArcticCV uses several types of machine learning (convolutional neural net: CNN, decision tree: DT, k-means unsupervised clustering: KM) to automate the video processing pipeline. These include inferring the start/stop of time segments of interest (1D CNN), measuring the time-dependent 2D recession of the material samples (2D CNN, DT), measuring the time-dependent shock standoff distance (2D CNN, DT), and post-processing cleaning of the recession data (KM). The software also provides a graphical user interface for ease of use. The results of using this tool on arc jet videos show non-linear time-dependent effects can be important for certain materials and characterizing certain failure modes.

Recession tracking↗
NASA NTRS2023

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

This final report documents work performed by ATA Engineering, Inc., (ATA) to develop computational models and analyze the coupled fluid-structure response of two types of noise treatments applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The first treatment is a slat-gap filler (SGF), which closes the gap between the suction surfaces of a deployed slat and an aircraft main wing, and the second treatment is a slat-cove filler (SCF), which replaces the recirculating flow on the slat cove with a surface that promotes flow attachment. The representative airframe chosen for this work was NASA’s High-Lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs were assessed for their static aeroelastic deflection as well as their dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL-CSD) tools. Specifically, fluid-structure interaction (FSI) problems were solved computationally using the CFD solver Loci/CHEM and the NL-CSD solver Abaqus. As a part of the overall project, a similar capability was implemented using the CFD solver FUN3D coupled to Abaqus, although that work is documented in a separate report and that FSI framework was not used to analyze any of NASA’s SGF and SCF configurations. The technical approach consisted of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design was analyzed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability, whereas the SCF was analyzed in 2D only. SGF static aeroelastic response predictions focused on characterizing the deformed shape, with maximum displacements predicted to be on the order of magnitude of the technology element panel thickness. SGF dynamic aeroelastic response predictions used Partial Floquet analysis of the temporal evolution of selected nodal displacements to quantify the sign and magnitude of aeroelastic damping. Results suggest that the CRM-HL operating conditions would result in a dynamically stable response. The simulated dynamic pressure was also increased up to a factor of about four, and resulting responses suggest that predicted dynamic stability would be achieved with some margin.

Fluid Structure Interaction↗
NASA NTRS1988

Unsteady delta-wing flow computation using an implicit factored Euler scheme

The conservative unsteady Euler equations for the flow relative motion in the moving frame of reference are used to solve for the steady and unsteady flows around sharp-edged delta wings. The resulting equations are solved by using an implicit approximately-factored finite-volume scheme. Implicit second-order and explicit second- and fourth-order dissipations are added to the scheme. The boundary conditions are explicitly satisfied. The grid is generated by locally using a modified Joukowski transformation in cross-flow planes at the grid chord stations. The computational applications cover a steady flow around a delta wing whose results serve as the initial conditions for the unsteady flow around a pitching delta wing about a large angle of attack. The steady results are compared with the experimental data and the periodic solution is achieved within the third cycle of oscillation.

Kandil, Osama A.↗
NASA NTRS2004

Computer Tomography 3-D Imaging of the Metal Deformation Flow Path in Friction Stir Welding

In friction stir welding, a rotating threaded pin tool is inserted into a weld seam and literally stirs the edges of the seam together. This solid-state technique has been successfully used in the joining of materials that are difficult to fusion weld such as aluminum alloys. To determine optimal processing parameters for producing a defect free weld, a better understanding of the resulting metal deformation flow path is required. Marker studies are the principal method of studying the metal deformation flow path around the FSW pin tool. In our study, we have used computed tomography (CT) scans to reveal the flow pattern of a lead wire embedded in a FSW weld seam. At the welding temperature of aluminum, the lead becomes molten and thus tracks the aluminum deformation flow paths in a unique 3-dimensional manner. CT scanning is a convenient and comprehensive way of collecting and displaying tracer data. It marks an advance over previous more tedious and ambiguous radiographic/metallographic data collection methods.

Schneider, Judy↗
NASA NTRS2015

DUKSUP: A Computer Program for High Thrust Launch Vehicle Trajectory Design and Optimization

From the late 1960s through 1997, the leadership of NASAs Intermediate and Large class unmanned expendable launch vehicle projects resided at the NASA Lewis (now Glenn) Research Center (LeRC). One of LeRCs primary responsibilities --- trajectory design and performance analysis --- was accomplished by an internally-developed analytic three dimensional computer program called DUKSUP. Because of its Calculus of Variations-based optimization routine, this code was generally more capable of finding optimal solutions than its contemporaries. A derivation of optimal control using the Calculus of Variations is summarized including transversality, intermediate, and final conditions. The two point boundary value problem is explained. A brief summary of the codes operation is provided, including iteration via the Newton-Raphson scheme and integration of variational and motion equations via a 4th order Runge-Kutta scheme. Main subroutines are discussed. The history of the LeRC trajectory design efforts in the early 1960s is explained within the context of supporting the Centaur upper stage program. How the code was constructed based on the operation of the AtlasCentaur launch vehicle, the limits of the computers of that era, the limits of the computer programming languages, and the missions it supported are discussed. The vehicles DUKSUP supported (AtlasCentaur, TitanCentaur, and ShuttleCentaur) are briefly described. The types of missions, including Earth orbital and interplanetary, are described. The roles of flight constraints and their impact on launch operations are detailed (such as jettisoning hardware on heating, Range Safety, ground station tracking, and elliptical parking orbits). The computer main frames on which the code was hosted are described. The applications of the code are detailed, including independent check of contractor analysis, benchmarking, leading edge analysis, and vehicle performance improvement assessments. Several of DUKSUPs many major impacts on launches are discussed including Intelsat, Voyager, Pioneer Venus, HEAO, Galileo, and Cassini.

Launch vehicle performance optimization↗
NASA NTRS1995

Analytical studies of hypersonic viscous dissociated flows

This project primarily dealt with integral boundary-layer solution techniques that are directly applicable to the problem of determining aerodynamic heating rates of hypersonic vehicles like X-33 in the vicinity of stagnation points, windward centerlines, and swept-wing leading edges. The analyses include effects of finite-rate gas chemistry across the boundary layer and finite-rate catalysis of atom recombination at the surface. A new approach for combining the insight afforded by integral boundary-layer analysis with comprehensive (and expensive) computational fluid dynamic (CFD) flowfield solutions of the thin-layer Navier-Stokes equations was developed. The approach extracts CFD derived quantities at the wall and at the boundary layer edge for inclusion in a post-processing boundary-layer analysis. The post-processed data base allows a designer at a workstation to ask and answer the following questions: (1) How much does the heating change if one uses a thermal protection system (TPS) with different catalytic properties than was used in the original CFD solution? (2) How does the heating change when one moves the interface of two different TPS materials with different catalytic efficiencies for the purpose of reducing vehicle weight and expense? The answer to the second question is particularly critical, because abrupt changes from low catalytic efficiency to high catalytic efficiency can lead to localized increase in heating which exceeds the usually conservative estimate provided by a fully catalytic wall assumption. A secondary issue that was addressed involves the prediction of heating levels in the vicinity of sharp corners that are transverse to or aligned with the flow. An example of the first case is heating at the edge of the COMET reentry module. An example of the second case is heating along the side edge of a deflected body flap on an SSV. The difficulty of putting grids in the vicinity of such corners with continuously varying metric coefficients causes problems in CFD predictions. A preliminary theory for prediction that says the heating at the corner is X percent of the heating N boundary-layer thicknesses inboard was developed. This will prove useful to analytically evaluate the possible benefits of rounding the edges of these configurations and defining how much rounding is sufficient.

Inger, George R.↗
NASA NTRS1982

Computation of the steady viscous flow over a tri-element 'augmentor wing' airfoil

The augmentor wing consists of a main airfoil with a slotted trailing edge for blowing, and two smaller aft airfoils which shroud the jet. This configuration has been modeled for numerical simulation by a novel discretization procedure which generates four separate grids: three surface-oriented airfoil grids and one outer free-stream grid. Grid lines and slopes are continuous across boundaries, so grid overlap at common boundaries provides boundary information without interpolation. A two-dimensional unsteady thin-layer Navier-Stokes code is used to calculate the flow for the no-blowing case at freestream Mach number = 0.7, Re = 12,600.000, and angles-of-incidence = 1.05 deg. Qualitative agreement with experimental data indicates the utility of this procedure in the analysis of multi-element configurations.

Lasinski, T. A.↗