Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Digitalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Development of digital electronics for the search of SHE nuclei using GARIS-II/III at RIKEN

This work describes the implementation of a digital data acquisition system for the search and study of short-lived isotopes or superheavy elements at the GARIS-III separator at the RIKEN Nishina Center. Here a reduction to 26 ± 0.5 keV in the average value of the Full Width at Half Maximum of the alpha spectrum at 7.133 MeV was achieved, combined with a reduction of the dead time of the overall system to around a few tens of nanoseconds for the detection of very fast decay chains. Moreover, we measured a reduction of the background induced by particles crossing the implantation detector using pulse shape analysis techniques. The detail of the optimization and analysis will be presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Time interval distributions of nuclear events in a digital spectrometer

This study compares the theoretical formula for time interval density distributions (TIDs) in counters with pileup rejection to TIDs measured using a digital spectrometer with trapezoid filtering. The TIDs were derived from successive time stamps of 60 Co and 133 Ba γ rays detected with a HPGe spectrometer. The results demonstrate that the theoretical formula is applicable up to 40% count loss and can be used to retrospectively deduce the incident event rate.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A sub-5 ps jitter time-to-digital converter ASIC with back-gate delay tuning in 22 nm CMOS

We present the design of a Time-to-Digital Converter (TDC) ASIC together with performance characterization results at cryogenic temperature (6-8 K), and at room temperature using emulated Low-Gain Avalanche Detector (LGAD) signals. The TDC design uses a two-step architecture with a ring-oscillator based counter and a Vernier delay line fine TDC. The TDC is implemented in an FD-SOI process, and back-gate tuning is used not only to correct threshold variation due to cryogenic operation, but also as a novel way to tune TDC delay elements with very little overhead. Using this technique, we demonstrate a design with very low power (0.5 mW) and area (0.003 mm 2 ). We present test results using the Fermilab Constant Fraction Discriminator (FCFD) ASIC to produce discriminated signals from an internal charge injection mechanism that mimics the waveform and signal amplitude of minimum ionizing particles impinging on LGAD sensors. We characterize the time precision of the full system and verify that the TDC ASIC contributes a negligible amount to the total system time precision, fully consistent with the expected jitter contribution of less than 5 ps. In conclusion, the results presented here demonstrate the utility of our TDC for applications in physics and quantum communications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A flexible polymer-based luminescent ink for combined thermographic phosphors and digital image correlation (TP+DIC)

Recent work on the development of integrated thermographic phosphors and digital image correlation (TP+DIC) for combined thermal–mechanical measurements has revealed the need for a flexible, stretchable phosphor coating for metal surfaces. Herein, we coat stainless steel substrates with a polymer-based phosphor ink in a DIC speckle pattern and demonstrate that the ink remains well bonded under substrate deformation. In contrast, a binderless phosphor DIC coating produced via aerosol deposition (AD) partially debonded from the substrate. DIC calculations reveal that the strain on the ink coating matches the strain on the substrate within 4% error at the highest substrate loads (0.05 mm/mm applied substrate strain), while the strain on the AD coating remains near 0 mm/mm as the substrate deforms. Spectrally resolved emission from the phosphor is measured through the transparent binder throughout testing, and the ratio method is used to infer temperature with an uncertainty of 1.7 °C. In conclusion, this phosphor ink coating will allow for accurate, non-contact strain and temperature measurements of a deforming surface.

36 MATERIALS SCIENCE↗

Digital force prediction for milling

This paper presents a fully digital, integrated approach for milling force prediction with arbitrary end mill-work material combinations. The approach includes: 1) structured light scanning to identify the end mill’s cutting edge macro-geometry along the tool axis; 2) structured light scanning to measure the cutting edge cross-sectional rake and relief profiles; 3) finite element analysis of orthogonal cutting to determine the force model coefficients that relate the force to chip area using the work material’s constitutive model and tool’s rake and relief profiles; and 4) time domain simulation with inputs that include the measured cutting edge macro-geometry, finite element-based force model, and measured structural dynamics. Milling force predictions are compared to in-process measurements to validate the method.

42 ENGINEERING↗

Bridging the simulator gap: Measuring motivational bias in digital nuclear power plant environments

Using digital NPP simulator facilities for research in Human Reliability Analysis (HRA) and nuclear power research is increasingly popular. For this work, we propose a method for characterizing and quantifying the gap between data collected in a simulator and data that reflect NPP operations. Using novice operators, we demonstrate how to manipulate and measure the impact of the simulator environment on operator actions. A set of biases are proposed to characterize factors introduced by the simulator environment. There are two categories of simulator bias: Environmental Biases (physical differences between the simulator and the control room), and Motivational Biases (cognitive differences between training in a simulator and operating a NPP). This study examines Motivational Bias. A preliminary causal model of Motivational Biases is introduced and tested in a demonstration experiment using 30 student operators. Data from 41 simulator sessions are analyzed. Data include crew characteristics, operator surveys, and time to recognize and diagnose the accident in the scenario. Quantitative models of the Motivational Biases using Structural Equation Modeling (SEM) are proposed. With these models, we estimate how the effects of the scenario conditions are mediated by simulator bias, and we demonstrate how to quantify the strength of these effects.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The use of a digital micromirror array as a temporal gate and spatial-filtering device for laser-induced breakdown spectroscopy and laser ablation molecular isotopic spectrometry

A digital micromirror array (DMMA) is used in a simple and inexpensive approach for spatially resolved temporal gating of atomic emission detection in laser-induced breakdown spectroscopy (LIBS). Selected mirrors in the array are actuated at a time delayed from the primary laser pulse, permitting optical gating with a response time of 160 ns while using a conventional CCD detector. Detector gating is shown to decrease noise from short-lived spectroscopic background (both continuum and N II from air), improving signal-to-background ratios by 22-times for selected samples and emission lines. The utility of rapid temporal gating is also demonstrated for the optical detection of isotopes using the laser-ablation molecular isotope spectrometry (LAMIS) experiment. Additionally, optical temporal gating and spatial filtering are used to isolate regions of the laser-induced plasma, enhancing signal from molecular emission. The potential of the simple technique for use in field-portable LIBS and LAMIS experiments is explored.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experimenting in the cloud: The digital divide's impact on innovation

This paper builds on a recent National Science Foundation working paper that identified a strong association between cloud use and various types of innovation but did not consider whether 1) cloud adoption is a reliable indicator of the innovation orientation of a firm, or 2) cloud adoption enables various types of innovation. We estimate propensity score matching and endogenous treatment effect models to control for innovation orientation, producing evidence to test the second explanation. Here, findings support an enabling effect of the cloud on innovation providing concrete evidence of the adverse impact of the digital divide.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

A primer on artificial intelligence in plant digital phenomics: embarking on the data to insights journey

Artificial intelligence (AI) has emerged as a fundamental component of global agricultural research that is poised to impact on many aspects of plant science. In digital phenomics, AI is capable of learning intricate structure and patterns in large datasets. We provide a perspective and primer on AI applications to phenome research. We propose a novel human-centric explainable AI (X-AI) system architecture consisting of data architecture, technology infrastructure, and AI architecture design. We clarify the difference between post hoc models and 'interpretable by design' models. We include guidance for effectively using an interpretable by design model in phenomic analysis. We also provide directions to sources of tools and resources for making data analytics increasingly accessible. In conclusion, this primer is accompanied by an interactive online tutorial.

60 APPLIED LIFE SCIENCES↗

Digital light processing of porous LLZTO scaffolds for Li-garnet solid-state batteries

Li 7 La 3 Zr 2 O 12 (LLZO)-based solid-state electrolytes (SEs) are promising materials for next-generation solid-state batteries. In this work, digital light processing (DLP), an emerging additive manufacturing technology, is employed to produce porous Ta-doped LLZO (LLZTO) scaffolds. The self-standing scaffolds are 100 μm thick and have 40% porosity. The scaffolds demonstrate symmetric cell cycling stability exceeding 1,500 h at 0.1 mA/cm2 current density, with a capacity of 0.1 mAh/cm 2 (1 h for each half cycle). At higher current densities, reversible soft shorts frequently happen, while immediate hard shorts are prevented due to Li dendrite growth being hindered by the tortuous pore network. In addition to the cycling stability, the phase stability of LLZTO is investigated during the post-printing thermal process for printing resin removal. We discovered that the LLZTO partially decomposes into Li 2 Zr 2 O 7 and other impurity phases from 400°C to 800°C, but the pure LLZTO phase is restored upon the completion of resin removal beyond 800°C.

Li-metal anode↗

Bayesian Conavigation: Dynamic Designing of the Material Digital Twins via Active Learning

Scientific advancement is universally based on the dynamic interplay between theoretical insights, modeling, and experimental discoveries. However, this feedback loop is often slow, including delayed community interactions and the gradual integration of experimental data into theoretical frameworks. This challenge is particularly exacerbated in domains dealing with high-dimensional object spaces, such as molecules and complex microstructures. Hence, the integration of theory within automated and autonomous experimental setups, or theory in the loop-automated experiment, is emerging as a crucial objective for accelerating scientific research. The critical aspect is to use not only theory but also on-the-fly theory updates during the experiment. Furthermore, we introduce a method for integrating theory into the loop through Bayesian conavigation of theoretical model space and experimentation. Our approach leverages the concurrent development of surrogate models for both simulation and experimental domains at the rates determined by latencies and costs of experiments and computation, alongside the adjustment of control parameters within theoretical models to minimize epistemic uncertainty over the experimental object spaces. This methodology facilitates the creation of digital twins of material structures, encompassing both the surrogate model of behavior that includes the correlative part and the theoretical model itself. While being demonstrated here within the context of functional responses in ferroelectric materials, our approach holds promise for broader applications, such as the exploration of optical properties in nanoclusters, microstructure-dependent properties in complex materials, and properties of molecular systems.

Microscopy↗

Evaluating microstructure evolution in an SOFC electrode using digital volume correlation

Degradation mechanisms within solid oxide fuel cells (SOFC) during thermal cycling limit operational start-up times and cell lifetime, and must therefore be better understood and mitigated. This work explores such mechanisms using digital volume correlation (DVC) techniques applied to lab-based X-ray tomograms where the microstructural evolution is evaluated during the operational cycling of a Ni–YSZ/YSZ cell. To emulate reduced start-up times, five tomograms were collected over four operational thermal cycles to 750 °C at various ramp-rates: 3, 10, 20 and 30 °C min –1 . Two key features are observed in the 3D strain profiles. Firstly, during low ramp-rates the material produces microscopic channels towards cluster-points. This is thought to be caused by the ceramic skeleton inhibiting the effects of sintering. Secondly, previously unseen macroscopic ‘waves’ developed after high-rate cycling, consisting of linear regions of compression and tension throughout the sample. These wave features decay away from a heterogeneous defect which is thought to be responsible for the non-uniform strain profile. This work demonstrates the first use of sub-micron DVC computations applied to an SOFC exposed to operationally relevant temperatures. Lastly, these findings will assist in the development of new electrode materials from their fabrication to operation, ultimately supporting commercial viability of SOFCs.

30 DIRECT ENERGY CONVERSION↗

Digital front-end electronics for a tagged neutron inspection system

In this paper, we shall present a simple VME front-end system that employs the FADC CAEN V1720 8- channel 12-bit 250-MS/s digitizer. This system produces coincidence spectra between the trigger particle and other detectors and it replaces the traditional technique of chaining analog electronics. Tests have been performed using a pulser working at different frequencies as well as employing a {sup 252}Cf source in concert with an array of detectors.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Note: Increasing dynamic range of digital-to-analog converter using a superconducting quantum interference device

Responses of a superconducting quantum interference device (SQUID) are periodically dependent on magnetic flux coupling to its superconducting ring and the period is a flux quantum (Φ{sub o} = h/2e, where h and e, respectively, express Planck's constant and elementary charge). Using this periodicity, we had proposed a digital to analog converter using a SQUID (SQUID DAC) of first generation with linear current output, interval of which corresponded to Φ{sub o}. Modification for increasing dynamic range by interpolating within each interval is reported. Linearity of the interpolation was also based on the quantum periodicity. A SQUID DAC with dynamic range of about 1.4 × 10{sup 7} was created as a demonstration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multichannel low power time-to-digital converter card with 21 ps precision and full scale range up to 10 μs

We present a Time-to-Digital Converter (TDC) card with a compact form factor, suitable for multichannel timing instruments or for integration into more complex systems. The TDC Card provides 10 ps timing resolution over the whole measurement range, which is selectable from 160 ns up to 10 μs, reaching 21 ps rms precision, 1.25% LSB rms differential nonlinearity, up to 3 Mconversion/s with 400 mW power consumption. The I/O edge card connector provides timing data readout through either a parallel bus or a 100 MHz serial interface and further measurement information like input signal rate and valid conversion rate (typically useful for time-correlated single-photon counting application) through an independent serial link.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A digital matched filter for reverse time chaos

The use of reverse time chaos allows the realization of hardware chaotic systems that can operate at speeds equivalent to existing state of the art while requiring significantly less complex circuitry. Matched filter decoding is possible for the reverse time system since it exhibits a closed form solution formed partially by a linear basis pulse. Coefficients have been calculated and are used to realize the matched filter digitally as a finite impulse response filter. Numerical simulations confirm that this correctly implements a matched filter that can be used for detection of the chaotic signal. In addition, the direct form of the filter has been implemented in hardware description language and demonstrates performance in agreement with numerical results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Broad-range tuning of ferroelectric switching of La x Bi 1−x FeO 3 epitaxial films via digital doping using off-axis co-sputtering

To investigate the scope of ferroelectric behavior in La-substituted BiFeO 3 films, La x Bi 1−x FeO 3 epitaxial films were synthesized using off-axis co-sputtering on SrTiO 3 (001) and DyScO 3 (110) substrates with a SrRuO 3 bottom electrode layer. A digital-doping deposition method was used to enable precise control and continuous tuning of La concentration in high-quality LaxBi 1−x FeO 3 films across a wide range of x = 0.05–0.60, which was systematically investigated using piezoresponse force microscopy. Robust and reversible out-of-plane ferroelectric switching has been observed up to x = 0.35, while films with x ≥ 0.37 exhibit no measurable ferroelectric behavior, indicating a sharp ferroelectric-to-paraelectric phase transition between x = 0.35 and 0.37. This represents the highest reported La concentration in LaxBi 1−x FeO 3 films that retains ferroelectric ordering, highlighting opportunities to engineer ferroelectric and multiferroic properties in complex oxide heterostructures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analog-to-digital converter based on voltage-controlled superconducting devices

The increasing demand for cryogenic electronics in superconducting and quantum computing systems calls for ultra-energy-efficient data conversion architectures that remain functional at deep cryogenic temperatures. Here, in this work, we present the first design of a voltage-controlled superconducting flash analog-to-digital converter (ADC) based on a voltage-controlled quantum-enhanced Josephson junction field-effect transistor (JJFET). Exploiting its strong gate tunability and transistor-like behavior, the JJFET offers a scalable alternative to conventional current-controlled superconducting devices while aligning naturally with CMOS-style design methodologies. Building on our previously developed Verilog-A compact model calibrated to experimental data, we design and simulate a three-bit JJFET-based flash ADC targeted for integration within cryogenic control and readout circuitry in quantum computing. The core comparator block is realized through careful bias current selection and augmented with a three-terminal nanocryotron to precisely define reference voltages. Cascaded JJFET comparators ensure robust voltage gain, cascadability, and logic-level restoration across stages. Simulation results demonstrate accurate quantization behavior with ultra-low power dissipation, underscoring the feasibility of voltage-driven superconducting mixed-signal circuits. This work establishes a critical step toward unifying superconducting logic and data conversion, paving the way for scalable cryogenic architectures in quantum–classical co-processors, low-power artificial intelligence accelerators, and next-generation energy-constrained computing platforms.

Analog-to-digital converter↗