Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Tunneling Back-Contacted Photovoltaics

This project examined the merits of tunnel insulators sandwiched between silicon absorbers and electron- and hole-selective contact materials for decreasing recombination at this interface. Decreases in recombination at this interface hold the potential to increase efficiency in silicon photovoltaic technologies, while exploiting low temperature (< 300°C) growth methods. The key findings of this project were that incorporating thin (< 3 nm) alumina tunnel layers did decrease interface recombination rates, however not to the extent observed in thick (> 10 nm) layers. The project also found that the most important implementation of tunnel layer passivation occurred with MoOx hole selective materials, since direct Si-MoOx contact yielded very high recombination velocities (S > 1000 cm -s ). The primary impact on the state of the art is that this project showed there is merit to incorporation of tunnel insulators between absorbers (e.g., Si) and selective contact materials (e.g., MoOx) in decreasing interface recombination rates while still allowing for carrier extraction the selective contact layer and into a metal.

14 SOLAR ENERGY↗
DOE OSTI2023

Schottky contacts on ultra-high-pressure-annealed GaN with high rectification ratio and near-unity ideality factor

Here we investigate the electrical characteristics of Ni Schottky contacts on n-type GaN films that have undergone ultra-high-pressure annealing (UHPA), a key processing step for activating implanted Mg. Contacts deposited on these films exhibit low rectification and high leakage current compared to contacts on as-grown films. By employing an optimized surface treatment to restore the GaN surface following UHPA, we obtain Schottky contacts with a high rectification ratio of ~10 9 , a near-unity ideality factor of 1.03, and a barrier height of ~0.9 eV. These characteristics enable the development of GaN junction barrier Schottky diodes employing Mg implantation and UHPA.

42 ENGINEERING↗
DOE OSTI2023

Comparative Study of TESS Photometry and Radial Velocities on Six Early K-type Contact Binaries with Similar Periods around 0.268 Day

High-precision light curves were extracted from TESScut images. Together with APOGEE and LAMOST medium-resolution spectra, a joint study was made for six early K-type contact binary candidates selected unbiasedly with orbital periods around 0.268 day. It is found that all of them (RV CVn, EK Com, V384 Ser, V1038 Her, EH CVn, and CSS_J125403.7+503945) are W-subtype shallow contact systems, though with different mass ratios (1/q = 0.27–0.62). The effective temperature differences between the binary components are around a few hundred kelvins. The original definitions of the A and W subtypes were compared with the customarily used methods, which rely on the shape or photometric solutions of the light curves. The latter two methods are not always reliable; therefore, the radial velocity analysis is strongly recommended. Through a collection of all available K-type contact binaries with both photometric and spectroscopic measurements, it is found that almost all of them are W-subtype systems, except for a few objects that have nearly identical temperatures for binary components. This W-subtype phenomenon for K-type contact binaries should be further checked with more samples in the future. Finally, the physical parameters of the targets were determined with joint data analysis, and the multiplicity is discussed for these targets. Objects V384 Ser and RV CVn are confirmed to very likely be triple systems from comprehensive analysis, while V1038 Her is a candidate of a triple system based on photometric and spectroscopic solutions.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Data Associated with "Identifying Suitable Front Contacts for High-Efficiency Cd(Se,Te) Solar Cells on Space-Qualified Cover Glass"

This is data associated with the publication " Identifying Suitable Front Contacts for High-Efficiency Cd(Se,Te) Solar Cells on Space-Qualified Cover Glass " by Aesha P. Patel, Ryan Muzzio, Matthew R. Young, Robert Morrissey, Suresh Chaulagain, B. Edward Sartor, Prabodika N. Kaluarachchi, Christian Velez, Joshua A. Brown, Joel N. Duenow, Stephen Glynn, Michael J. Heben, Zhaoning Song, Nikolas J. Podraza, Adam B. Phillips, Randy J. Ellingson, Matthew O. Reese. All data associated with each figure in the manuscript and supplementary should be available in this dataset. A readme file is also included to provide some guidance. Abstract: Deployment of photovoltaics in space requires devices that combine high-efficiency, low areal mass, and resilience to harsh environments. Historically, high-efficiency multijunction III–V materials have dominated space power systems; however, their high cost and limited manufacturing throughput motivate the exploration of scalable alternatives. While CdTe-based thin-film photovoltaics offer an attractive option, their performance on non-conventional substrates can suffer from front-contact instability under higher-temperature processing. Here, the role of front-contact chemistry in limiting cell performance is investigated using CdTe-based devices fabricated on 150 μm thick Ceria-doped space-qualified 0214 Corning glass. A matrix of four transparent conducting oxides (TCOs: CTO, AZO, ITO, IZO) combined with two n-type emitters (MZO, IGO) reveals chemical stability at the front interface—rather than absorber composition alone—governs recombination losses, voltage deficits, and device reproducibility. Chemically stable front-contact combinations suppress elemental diffusion and interfacial degradation, resulting in significantly improved carrier lifetimes and junction quality. These insights are validated through record-certified Cd(Se,Te) cell efficiencies of 18.4% under AM1.5G and 16.2% under AM0 illumination on ultra-thin glass. Beyond CdTe, this work provides a general framework for the rational selection of TCO/emitter interfaces in superstrate thin-film photovoltaics, including emerging technologies like metal halide perovskites, while enabling high-efficiency, lightweight photovoltaics for space applications.

14 SOLAR ENERGY↗
NASA NTRS1972

A reliable all-silver front contact for silicon solar cells

The feasibility of making an adherent and moisture degradation resistant silver-only front contact to silicon solar cells was demonstrated. Optimum fabrication processes and process sequences were determined for making such contacts. These contacts were found to also have good electrical characteristics. A back contact of aluminum-silver was also developed. This proved very satisfactory for low-temperature applications.

Lamneck, J. H., Jr.↗
NASA NTRS1972

Cross flow in a starved EHD contact

An analysis of lubrication cross flow effects under starved elastohydrodynamic conditions is presented. Starvation is defined as any operating condition such that an increase in oil available to the contact will result in an increase in film thickness. Starved EHD behavior is considered in several situations: (1) when no new oil enters the contact, and (2) when a step change in one of the rolling parameters is introduced at an equilibrium contact. Based on the fact that important oil flow within the Hertz zone is across the rolling contact direction, it is possible to formulate a simple theory which explains quantitatively some aspects of starved ball bearing behavior.

Kingsburg, E. P.↗
NASA NTRS1972

Optical interferometry study of film formation in lubrication of sliding and/or rolling contacts

Seventeen fluids of widely varying physical properties and molecular structure were chosen for study. Film thickness and traction were measured simultaneously in point contacts by interferometry, from which a new theory of traction was proposed. Film thickness was measured in line contacts by interferometry and electrical capacitance to establish correlation between these two methods. An interferometric method for the absolute determination of refractive index in the contact zone was developed and applied to point contact fluid entrapments. Electrical capacitance was used to study the thickness and properties of the soft surface film which sometimes forms near a metal-fluid interface.

Stejskal, E. O.↗
NASA NTRS1973

Contact problem for an elastic reinforcement bonded to an elastic plate

The stiffening layer is treated as an elastic membrane and the base plate is assumed to be an elastic continuum. The bonding between the two materials is assumed to be either one of direct adhesion ro through a thin adhesive layer which is treated as a shear spring. The solution for the simple case in which both the stiffener and the base plate are treated as membranes is also given. The contact stress is obtained for a series of numerical examples. In the direct adhesion case the contact stress becomes infinite at the stiffener ends with a typical square root singularity for the continuum model, and behaving as a delta function for the membrane model. In the case of bonding through an adhesive layer the contact stress becomes finite and continuous along the entire contact area.

Erdogan, F.↗
NASA NTRS1974

Numerical evaluation of the surface deformation of elastic solids subjected to a hertzian contact stress

The elastic deformation of two ellipsoidal solids in contact and subjected to Hertzian stress distribution was evaluated numerically as part of a general study of the elastic deformation of such solids in elastohydrodynamic contacts. In the analysis the contact zone was divided into equal rectangular areas, and it was assumed that a uniform pressure is applied over each rectangular area. The influence of the size of the rectangular area upon accuracy was also studied. The results indicate the distance from the center of the contact at which elastic deformation becomes insignificant.

Hamrock, B. J.↗
NASA NTRS1973

A thermal, thermoelastic, and wear simulation of a high-energy sliding contact problem

This paper describes an investigation of the sliding contact problem encountered in high-energy disk brakes. The analysis includes a simulation modeling, using the finite element method, of the thermoelastic instabilities that cause transient changes in contact to occur on the friction surface. In order to include the effect of wear of the concentrated contacts on the friction surface, a wear criterion is proposed that results in prediction of wear rates for disk brakes that are quite close to experimentally determined wear rates. The thermal analysis shows that the transient temperature distribution in a disk brake can be determined more accurately by use of this thermomechanical analysis than by a more conventional analysis that assumes constant contact conditions. It is also shown that lower, more desirable, temperatures in disk brakes can be attained by increasing the volume, the thermal conductivity, and especially, the heat capacity of the brake components.

Kennedy, F. E., Jr.↗
NASA NTRS1975

Numerical evaluation of the surface deformation of elastic solids subjected to a Hertzian contact stress

The elastic deformation of two ellipsoidal solids in contact and subjected to a Hertzian stress distribution was evaluated numerically as part of a general study of the elastic deformation of such solids in elastohydrodynamic contacts. In the analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each rectangular area. A study was made of the influence on the size of the rectangular area upon accuracy. The results also indicate how far from the center of the contact one needs to go before elastic deformation becomes insignificant.

Dowson, D.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. 1: Theoretical formulation

The isothermal elastohydrodynamic lubrication (EHL) of a point contact was analyzed numerically by simultaneously solving the elasticity and Reynolds equations. In the elasticity analysis the contact zone was divided into equal rectangular areas, and it was assumed that a uniform pressure was applied over each area. In the numerical analysis of the Reynolds equation, a phi analysis (where phi is equal to the pressure times the film thickness of the 3/2 power) was used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗
NASA NTRS1974

Traction of elastohydrodynamic contacts with thermal shearing flow

The formulation and solution for the shear stress and temperature in heavily loaded sliding elastohydrodynamic contacts is presented. The solutions are presented in dimensionless design charts. Integration over the contact area will yield the traction. Accuracy is expected to be very good over the nearly flat part of the contact area where the majority of the sliding traction is generated. The procedure presented is not appropriate for thick film lubrication, for the inlet region, or for the rolling friction of elastohydrodynamic contacts.

Jakobsen, J.↗
NASA NTRS1975

Numerical evaluation of the surface deformation of elastic solids subjected to a Hertzian contact stress

The elastic deformation of two ellipsoidal solids in contact and subjected to a Hertzian stress distribution has been evaluated numerically as part of a general study of the elastic deformation of such solids in elastohydrodynamic contacts. In the analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each rectangular area. A study has been made of the influence on the size of the rectangular area upon accuracy. The results also indicate how far from the center of the contact one needs to go before elastic deformation becomes insignificant.

Dowson, D.↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. 2: Ellipticity parameter results

A numerical solution of the isothermal elastohydrodynamic problem for point contacts is presented which reproduces all the essential features of experimental observations based upon optical interferometry. In particular, the two side lobes, in which minimum film thickness regions occur, emerge in the theoretical solutions. The influence of the ellipticity parameter on solutions to the point contact problem is explored. The ellipticity parameter k was varied from 1 (a ball on a plate) to 8 (a configuration approaching line contact). It is shown that the minimum film thickness can be related to the well known line contact solutions by a remarkably simple expression involving either k or the effective radius of curvature ratio R sub y/R sub x.

Hamrock, B. J.↗
NASA NTRS1976

Simplified solution for point contact deformation between two elastic solids

A linear-regression by the method of least squares is made on the geometric variables that occur in the equation for point contact deformation. The ellipticity and the complete eliptic integrals of the first and second kind are expressed as a function of the x, y-plane principal radii. The ellipticity was varied from 1 (circular contact) to 10 (a configuration approaching line contact). These simplified equations enable one to calculate easily the point-contact deformation to within 3 percent without resorting to charts or numerical methods.

Brewe, D. E.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. II - Ellipticity parameter results

A numerical solution of the isothermal elastohydrodynamic problem for point contacts has been presented which reproduces all the essential features of the previously reported experimental observations based upon optical interferometry. In particular, the two 'side lobes' in which minimum film thickness regions occur are shown to emerge in the theoretical solutions. The influence of the ellipticity parameter upon solutions to the point contact problem has been explored in the present paper. The ellipticity parameter (k) was varied from one (a ball on a plate) to eight (a configuration approaching line contact), and it has been shown that both the central and minimum film thicknesses can be related to the well known line contact solutions by remarkably simple expressions involving either (k) or the effective radius of curvature ratio (Ry/Rx).

Hamrock, B. J.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. I - Theoretical formulation

The analysis of an isothermal elastohydrodynamic lubrication (EHL) point contact was evaluated numerically. This required the simultaneous solution of the elasticity and Reynolds equations. In the elasticity analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each element. In the numerical analysis of the Reynolds' equation a phi analysis where phi is equal to the pressure times the film thickness to the 3/2 power is used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗