SEARCH · Engineering Papers

Results for “Composite models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS2024

Analytical Simulation of the Effects of Local Mechanisms and Microstructure on the Creep Response of Unidirectional Ceramic Matrix Composites

A micromechanics-based method has been developed to analyze the creep response of uncoated ceramic matrix minicomposites. Although the global stress level at which the creep response is analyzed is lower than the composite proportional limit, local stresses are assumed to be high enough that localized damage is present in the composite in the form of matrix microcracks. To model the composite creep response including the effects of matrix cracking, a fiber shear lag-based methodology is employed. In this approach, stresses are assumed to vary in the fiber as a function of time and distance from the crack plane. The varying stresses are then used to compute the overall creep strain for the composite. Various assumptions regarding the level of matrix microcracking in the composite, and the level of creep in the fiber and matrix in various portions of the composite unit cell, are also examined. The creep response of the fiber is modeled using a linear Burgers model. The model is applied to a SiC f /SiC unidirectional minicomposite system. The computed creep results are compared to experimentally obtained values. The effects of the local fiber volume fraction on the overall creep response of the composite are also studied. This work will allow increased understanding of the key material damage mechanisms and load sharing that take place during creep conditions and can be expanded to provide improved analysis methods for full macrocomposites.

Micromechanics↗

NASA NTRS2002

Constitutive Modeling of Nanotube-Reinforced Polymer Composites

In this study, a technique is presented for developing constitutive models for polymer composite systems reinforced with single-walled carbon nanotubes (SWNT). Because the polymer molecules are on the same size scale as the nanotubes, the interaction at the polymer/nanotube interface is highly dependent on the local molecular structure and bonding. At these small length scales, the lattice structures of the nanotube and polymer chains cannot be considered continuous, and the bulk mechanical properties can no longer be determined through traditional micromechanical approaches that are formulated by using continuum mechanics. It is proposed herein that the nanotube, the local polymer near the nanotube, and the nanotube/polymer interface can be modeled as an effective continuum fiber using an equivalent-continuum modeling method. The effective fiber serves as a means for incorporating micromechanical analyses for the prediction of bulk mechanical properties of SWNT/polymer composites with various nanotube shapes, sizes, concentrations, and orientations. As an example, the proposed approach is used for the constitutive modeling of two SWNT/LaRC-SI (with a PmPV interface) composite systems, one with aligned SWNTs and the other with three-dimensionally randomly oriented SWNTs. The Young's modulus and shear modulus have been calculated for the two systems for various nanotube lengths and volume fractions.

Odegard, G. M.↗

NASA NTRS2017

A Case for Nebula Scale Mixing Between Non-Carbonaceous and Carbonaceous Chondrite Reservoirs: Testing the Grand Tack Model with Chromium Isotopic Composition of Almahata Sitta Stone 91A

There is an increasing number of Cr-O-Ti isotope studies that show solar system materials are divided into two main populations, one carbonaceous chondrite (CC)-like and the other is non-carbonaceous (NC)-like, with minimal mixing attributed to a gap opened in the protoplanetary disk due to Jupiter's formation. The Grand Tack model suggests there should be large-scale mixing between S- and C-type asteroids, an idea supported by our recent work on chondrule (Delta)17O-ε54Cr isotope systematics. The Almahata Sitta (AhS) meteorite provides a unique opportunity to test the Grand Tack model. The meteorite fell to Earth in October 2008 and has been linked to the asteroid 2008 TC3 which was discovered just prior to the fall of the AhS stones. The AhS meteorite is composed of up to 700 individual pieces with approx.140 of those pieces having some geochemical and/or petrologic studies. Almahata Sitta is an anomalous polymict ureilite with other meteorite components, including enstatite, ordinary, and carbonaceous chondrites with an approximate abundance of 70% ureilites and 30% chondrites. This observation has lead to the suggestion that TC3 2008 was a loosely aggregated rubble pile-like asteroid with the non-ureilite sample clasts within the rubble-pile. Due to the loosely-aggregated nature of AhS, the object disintegrated during atmospheric entry resulting in the weakly held clasts falling predominantly as individual stones in the AhS collection area. However, recent work has identified one sample of AhS, sample 91A, which may represent two different lithologies coexisting within a single stone. The predominate lithology type in 91A appears to be that of a C2 chondrite based on mineralogy but also contains olivine, pyroxene, and albite that have ureilite-like compositions. Previous Cr isotope investigations into AhS stones are sparse and what data is available show nearly uniform isotopic composition similar to that of typical ureilites with negative ε54Cr values.

Sanborn, M. E.↗

NASA NTRS2006

Modeling the Stress Strain Behavior of Woven Ceramic Matrix Composites

Woven SiC fiber reinforced SiC matrix composites represent one of the most mature composite systems to date. Future components fabricated out of these woven ceramic matrix composites are expected to vary in shape, curvature, architecture, and thickness. The design of future components using woven ceramic matrix composites necessitates a modeling approach that can account for these variations which are physically controlled by local constituent contents and architecture. Research over the years supported primarily by NASA Glenn Research Center has led to the development of simple mechanistic-based models that can describe the entire stress-strain curve for composite systems fabricated with chemical vapor infiltrated matrices and melt-infiltrated matrices for a wide range of constituent content and architecture. Several examples will be presented that demonstrate the approach to modeling which incorporates a thorough understanding of the stress-dependent matrix cracking properties of the composite system.

Morscher, Gregory N.↗

NASA NTRS2003

Hydrostatic Stress Effects Incorporated Into the Analysis of the High-Strain-Rate Deformation of Polymer Matrix Composites

Procedures for modeling the effect of high strain rate on composite materials are needed for designing reliable composite engine cases that are lighter than the metal cases in current use. The types of polymer matrix composites that are likely to be used in such an application have a deformation response that is nonlinear and that varies with strain rate. The nonlinearity and strain rate dependence of the composite response is primarily due to the matrix constituent. Therefore, in developing material models to be used in the design of impact-resistant composite engine cases, the deformation of the polymer matrix must be correctly analyzed. However, unlike in metals, the nonlinear response of polymers depends on the hydrostatic stresses, which must be accounted for within an analytical model. An experimental program has been carried out through a university grant with the Ohio State University to obtain tensile and shear deformation data for a representative polymer for strain rates ranging from quasi-static to high rates of several hundred per second. This information has been used at the NASA Glenn Research Center to develop, characterize, and correlate a material model in which the strain rate dependence and nonlinearity (including hydrostatic stress effects) of the polymer are correctly analyzed. To obtain the material data, Glenn s researchers designed and fabricated test specimens of a representative toughened epoxy resin. Quasi-static tests at low strain rates and split Hopkinson bar tests at high strain rates were then conducted at the Ohio State University. The experimental data confirmed the strong effects of strain rate on both the tensile and shear deformation of the polymer. For the analytical model, Glenn researchers modified state variable constitutive equations previously used for the viscoplastic analysis of metals to allow for the analysis of the nonlinear, strain-rate-dependent polymer deformation. Specifically, we accounted for the effects of hydrostatic stresses. An important discovery in the course of this work was that the hydrostatic stress effects varied during the loading process, which needed to be accounted for within the constitutive equations. The model is characterized primarily by shear data, with tensile data used to characterize the hydrostatic stress effects.

Goldberg, Robert K.↗

NASA NTRSDate not supplied

Hierarchical Multiscale Process Modeling of A Textile Composite Y-Joint for the Aurora D8 Aircraft

Woven polymer matrix composites (PMCs) are widely used in aerospace applications for their favorable specific properties. However, the behavior of the inter- and intra-tow matrix during manufacturing of woven PMCs is difficult to isolate experimentally due to geometric and processing complexities. Classical closed-form homogenization approaches allow for composite thermos-chemo-mechanical properties to be characterized at any fiber volume fraction. In this work, virtual curing is applied to the inter- and intra-tow matrix materials of a plain weave repeating unit cell (RUC). Thermo-chemo-mechanical property evolution within the tows is calculated using the Concentric Cylinder Model (CCM) and the Rule of Mixtures (ROM). Curing is implemented through user-written subroutines within the commercial finite element method software Abaqus. Virtual curing results are compared with those from a linear-elastic thermal cool down simulation in Abaqus. Results indicate that tow property evolution during curing has a non-negligible effect on the final stress state.

curing↗

DOE OSTI2021

Seawater sea-sand engineered/strain-hardening cementitious composites (ECC/SHCC): Assessment and modeling of crack characteristics

Highlights: • A probabilistic model was proposed to model the crack width evolution of SS-ECC at different strain levels. • The Weibull distribution fit the crack width distribution better than the log-normal distribution. • A 5-D representation was proposed to assess the SS-ECC by considering both cracking and mechanical performance. • Larger sea-sand size and lower fiber dosage led to larger crack widths in SS-ECC under the same tensile strain. • 18-mm PE fiber led to larger crack widths in SS-ECC at strain >2%, due to a large fraction of fiber rupture. Seawater sea-sand Engineered Cementitious Composites (SS-ECC) is a new version of ECC for marine constructions facing the scarcity of freshwater and river/manufactured sand. This study aims to assess and model the crack characteristics of SS-ECC, which are critical for its applications with non-corrosive reinforcements. The influence of sea-sand size, fiber length and fiber dosage on the crack characteristics of SS-ECC was explored. A five-dimensional representation was proposed to assess the overall performance of SS-ECC, by comprehensively considering both the crack characteristics (i.e., crack width and its variation) and the mechanical properties (i.e., compressive and tensile properties). A probabilistic model was also proposed to describe the stochastic nature and evolution of crack width, and it can be used to estimate the critical tensile strain on SS-ECC for a given crack-width limit and cumulative probability. The findings and proposed methods can facilitate the design of SS-ECC in marine and coastal structures.

36 MATERIALS SCIENCE↗

NASA NTRS2016

Molecular Dynamics Modeling of Carbon Nanotube Composite Fracture Using ReaxFF

Carbon nanotube (CNT) fiber reinforced composites with specific tensile strengths and moduli approaching those of aerospace grade carbon fiber composites have recently been reported. This achievement was enabled by the emerging availability of high N/tex yarns in kilometer-scale quantities. While the production of this yarn is an impressive advance, its strength is still much lower than that of the individual CNTs comprising the yarn. Closing this gap requires understanding load transfer between CNTs at the nanometer dimensional scale. This work uses reactive molecular dynamics simulations to gain an understanding at the nanometer scale of the key factors that determine CNT nanocomposite mechanical performance, and to place more realistic upper bounds on the target properties. While molecular dynamics simulations using conventional force fields can predict elastic properties, the ReaxFF reactive forcefield can also model fracture behavior because of its ability to accurately describe bond breaking and formation during a simulation. The upper and lower bounds of CNT composite properties are investigated by comparing systems composed of CNTs continuously connected across the periodic boundary with systems composed of finite length CNTs. These lengths, effectively infinite for the continuous tubes and an aspect ratio of 13 for the finite length case, result from practical limitations on the number of atoms that can be included in a simulation. Experimentally measured aspect ratios are typically on the order of 100,000, so the calculated results should represent upper and lower limits on experimental mechanical properties. Finally, the effect of various degrees of covalent crosslinking between the CNTs and amorphous carbon matrix is considered to identify the amount of CNT-matrix covalent bonding that maximizes overall composite properties.

Jensen, Benjamin D.↗

NASA NTRS1994

Sub-ply level scaling approach investigated for graphite-epoxy composite beam columns

Scale model graphite-epoxy composite specimens were fabricated using the 'sub-ply level' approach and tested as beam-columns under an eccentric axial load to determine the effect of specimen size on flexural response and failure. In the current research project, although the fiber diameters are not scaled, the thickness of the pre-preg material itself has been scaled by adjusting the number of fibers through the thickness of a single ply. Three different grades of graphite-epoxy composite material (AS4/3502) were obtained from Hercules, Inc., in which the number of fibers through the thickness of a single ply was reduced (Grade 190 with 12 to 16 fibers, Grade 95 with 6 to 8 fibers, and Grade 48 with 3 to 4 fibers). Thus, using the sub-ply level approach, a baseline eight ply quasi-isotropic laminate could be fabricated using either the Grade 48 or Grade 95 material and the corresponding full-scale laminate would be constructed from Grade 95 or standard Grade 190 material, respectively. Note that in the sub-ply level approach, the number of ply interfaces is constant for the baseline and full-scale laminates. This is not true for the ply level and sublaminate level scaled specimens. The three grades of graphite-epoxy composite material were used to fabricate scale model beam-column specimens with in-plane dimensions of 0.5*n x 5.75*n, where n=1,2,4 corresponsing to 1/4, 1/2, and full-scale factors. Angle ply, cross ply, and quasi-isotropic laminate stacking sequences were chosen for the investigation and the test matrices for each laminate type are given. Specimens in each laminate family with the same in-plane dimensions but different thicknesses were tested to isolate the influence of the thickness dimension on the flexural response and failure. Also, specific lay-ups were chosen with blocked plies and dispersed plies for each laminate type. Specimens were subjected to an eccentric axial load until failure. The load offset was introduced through a set of hinges which were attached to the platens of a standard load test machine. Three sets of geometrically scaled hinges were used to ensure that scaled loading conditions were applied. This loading condition was chosen because it promotes large flexural deformations and specimens fail at the center of the beam, away from the grip supports. Five channels of data including applied vertical load, end shortening displacement, strain from gages applied back-to-back at the midspan of the beam, and rotation of the hinge from a bubble inclinometer were recorded for each specimen. The beam-column test configuration was used previously to study size effects in ply level scaled composite specimens of the same material system, sizes, and stacking sequences. Thus, a direct comparison between the two scaling approaches is possible. Ply level scaled beam-columns with angle ply, cross ply, and quasi-isotropic lay-ups exhibited no size dependencies in the flexural response, but significant size effects in strength. The reduction in strength with increasing specimen size was not predicted successfully by analysis techniques. It is anticipated that results from this investigation will lead to a better understanding of the strength scale effect in composite structures.

Jackson, Karen E.↗

NASA NTRS1992

A domain-specific design architecture for composite material design and aircraft part redesign

Advanced composites have been targeted as a 'leapfrog' technology that would provide a unique global competitive position for U.S. industry. Composites are unique in the requirements for an integrated approach to designing, manufacturing, and marketing of products developed utilizing the new materials of construction. Numerous studies extending across the entire economic spectrum of the United States from aerospace to military to durable goods have identified composites as a 'key' technology. In general there have been two approaches to composite construction: build models of a given composite materials, then determine characteristics of the material via numerical simulation and empirical testing; and experience-directed construction of fabrication plans for building composites with given properties. The first route sets a goal to capture basic understanding of a device (the composite) by use of a rigorous mathematical model; the second attempts to capture the expertise about the process of fabricating a composite (to date) at a surface level typically expressed in a rule based system. From an AI perspective, these two research lines are attacking distinctly different problems, and both tracks have current limitations. The mathematical modeling approach has yielded a wealth of data but a large number of simplifying assumptions are needed to make numerical simulation tractable. Likewise, although surface level expertise about how to build a particular composite may yield important results, recent trends in the KBS area are towards augmenting surface level problem solving with deeper level knowledge. Many of the relative advantages of composites, e.g., the strength:weight ratio, is most prominent when the entire component is designed as a unitary piece. The bottleneck in undertaking such unitary design lies in the difficulty of the re-design task. Designing the fabrication protocols for a complex-shaped, thick section composite are currently very difficult. It is in fact this difficulty that our research will address.

Punch, W. F., III↗

DOE OSTI2022

Composite excitonic states in doped semiconductors

We present a theoretical model of composite excitonic states in doped semiconductors. Many-body interactions between a photoexcited electron-hole pair and the electron gas are integrated into a computationally tractable few-body problem, solved by the variational method. We focus on electron-doped monolayer (ML)-MoSe 2 and ML-WSe 2 due to the contrasting character of their conduction bands. In both cases, the core of the composite is a tightly bound trion (two electrons and a valence-band hole) surrounded by a region depleted of electrons. The composite in ML-WSe 2 further includes a satellite electron with different quantum numbers. The theory is general and can be applied to semiconductors with various energy-band properties, allowing one to calculate their excitonic states and to quantify the interaction with the Fermi sea.

36 MATERIALS SCIENCE↗

NASA NTRS1991

Analysis of aircraft engine blade subject to ice impact

The ice impact on the engine blade made of layered composite is simulated. The ice piece is modeled as an equivalent spherical object and has the velocity opposite to that of the aircraft with direction parallel to the engine axis. Near the impact region and along the leading edge, the blade is assumed to be fully stressed and undergoes large deflection. A specified portion of the blade around the impact region is modeled. The effect of ice size and velocity on the average leading edge strain are investigated for a modified SR-2 model unswept composite propfan blade. Parametric studies are performed to study the response due to ice impact at various locations along the span. Also, the effects of engine speed on the strain and impact displacements are discussed. It is found that for a given engine speed, a critical ice speed exists that corresponds to the maximum strain and this critical speed increases with increase in the engine speed.

Reddy, E. S.↗

NASA NTRS1993

Axisymmetric micromechanics of elastic-perfectly plastic fibrous composites under uniaxial tension loading

The uniaxial response of a continuous fiber elastic-perfectly plastic composite is modeled herein as a two-element composite cylinder. An axisymmetric analytical micromechanics solution is obtained for the rate-independent elastic-plastic response of the two-element composite cylinder subjected to tensile loading in the fiber direction for the case wherein the core fiber is assumed to be a transversely isotropic elastic-plastic material obeying the Tsai-Hill yield criterion, with yielding simulating fiber failure. The matrix is assumed to be an isotropic elastic-plastic material obeying the Tresca yield criterion. It is found that there are three different circumstances that depend on the fiber and matrix properties: fiber yield, followed by matrix yielding; complete matrix yield, followed by fiber yielding; and partial matrix yield, followed by fiber yielding, followed by complete matrix yield. The order in which these phenomena occur is shown to have a pronounced effect on the predicted uniaxial effective composite response.

Lee, Jong-Won↗

NASA NTRS1994

Composition of energetic particles from solar flares

We present a model for composition of heavy ions in the Solar Energetic Particles (SEP). The SEP composition in a typical large solar particle event reflects the composition of the Sun, with adjustments due to fractionation effects which depend on the First Ionization Potential (FIP) of the ion and on the ratio of ionic charge to mass (Q/M). Flare-to flare variations in composition are represented by parameters describing these fractionation effects and the distributions of these parameters are presented.

Garrard, T. L.↗

NASA NTRS1992

Analysis of aircraft engine blade subject to ice impact

The ice impact problem on an engine blade made of layered composite is simulated. The ice piece is modeled as an equivalent spherical object and has the velocity opposite to that of the aircraft with direction parallel to the engine axis. Near the impact region and along the leading edge, the blade is assumed to be fully stressed and undergoes large deflection. A specified portion of the blade around the impact region is modeled. The effect of ice size and velocity on the average leading edge strain are investigated for a modified SR-2 model unswept composite propfan blade. Parametric studies are performed to study the response due to ice impact at various locations along the span. Also, the effects of engine speed on the strain and impact displacements are discussed. It is found that for a given engine speed, a critical ice speed exists that corresponds to the maximum strain and this critical speed increases with increase in the engine speed.

Reddy, E. S.↗

NASA NTRS2005

Damage Prediction Models for Advanced Materials and Composites

In the present study, the assessment and evaluation of various acoustic tile designs were conducted using three-dimensional finite element analysis, which included static analysis, thermal analysis and modal analysis of integral and non-integral tile design options. Various benchmark specimens for acoustic tile designs, including CMC integral T-joint and notched CMC plate, were tested in both room and elevated temperature environment. Various candidate ceramic matrix composite materials were used in the numerical modeling and experimental study. The research effort in this program evolved from numerical modeling and concept design to a combined numerical analysis and experimental study. Many subjects associated with the design and performance of the acoustic tile in jet engine exhaust nozzle have been investigated.

Xie, Ming↗

NASA NTRS2001

Constitutive Modeling of Nanotube-Reinforced Polymer Composite Systems

In this study, a technique has been proposed for developing constitutive models for polymer composite systems reinforced with single-walled carbon nanotubes (SWNT). Since the polymer molecules are on the same size scale as the nanotubes, the interaction at the polymer/nanotube interface is highly dependent on the local molecular structure and bonding. At these small length scales, the lattice structures of the nanotube and polymer chains cannot be considered continuous, and the bulk mechanical properties of the SWNT/polymer composites can no longer be determined through traditional micromechanical approaches that are formulated using continuum mechanics. It is proposed herein that the nanotube, the local polymer near the nanotube, and the nanotube/polymer interface can be modeled as an effective continuum fiber using an equivalent-continuum modeling method. The effective fiber retains the local molecular structure and bonding information and serves as a means for incorporating micromechanical analyses for the prediction of bulk mechanical properties of SWNT/polymer composites with various nanotube sizes and orientations. As an example, the proposed approach is used for the constitutive modeling of two SWNT/polyethylene composite systems, one with continuous and aligned SWNT and the other with discontinuous and randomly aligned nanotubes.

Odegard, Gregory M.↗

NASA NTRS2004

Constitutive Modeling of Nanotube-Reinforced Polymer Composite Systems

Odegard, Gregory M.↗