Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cell Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Recovery of shallow junction GaAs solar cells damaged by electron irradiation

Solar cells operated in space are subject to degradation from electron and proton radiation damage. It has been found that for deep junction p-GaAlAs/p-GaAs solar cells some of the electron radiation damage is removed by annealing the cells at 200 C. The reported investigation shows that shallow junction p-GaAlAs/p-GaAs/n-GaAs heteroface solar cells irradiated with 1 MeV electrons show a more complete recovery of short-circuit current than do the deep junction cells. The heteroface p-GaAlAs/p-GaAs/n-GaAs solar cells studied were fabricated using the etch-back epitaxy process.

Walker, G. H.↗
NASA NTRS1979

Silicon Web Process Development

Silicon dendritic web, ribbon form of silicon and capable of fabrication into solar cells with greater than 15% AMl conversion efficiency, was produced from the melt without die shaping. Improvements were made both in the width of the web ribbons grown and in the techniques to replenish the liquid silicon as it is transformed to web. Through means of improved thermal shielding stress was reduced sufficiently so that web crystals nearly 4.5 cm wide were grown. The development of two subsystems, a silicon feeder and a melt level sensor, necessary to achieve an operational melt replenishment system, is described. A gas flow management technique is discussed and a laser reflection method to sense and control the melt level as silicon is replenished is examined.

Duncan, C. S.↗
NASA NTRS1979

High Efficiency, High Density Terrestrial Panel

Terrestrial panels were fabricated using rectangular cells. Packing densities in excess of 90% with panel conversion efficiencies greater than 13% were obtained. Higher density panels can be produced on a cost competitive basis with the standard salami panels.

Wohlgemuth, J.↗
NASA NTRS1978

Status of wraparound contact solar cells and arrays

The paper describes the development of wraparound contact solar cell technology. Future development trends are distinguished. The current method of module fabrication with wraparound contact cells is briefly reviewed. The prospects for automated cell assembly are discussed.

Baraona, C. R.↗
NASA NTRS1979

Progress on the Dow Corning process for solar-grade silicon

The Dow Corning approach to increasing the resistivity of solar-grade silicon from about 0.04 ohm-cm (40 ppma B) to greater than 0.1 ohm-cm (10 ppma B) involves the use of high-purity raw materials carbothermically reduced in a specially designed electric arc furnace. Final purification occurs during Czochralski crystal growth of a polycrystalline ingot. This small-scale purification technology has resulted in silicon that has been fabricated into solar cells with a maximum AM1 conversion efficiency of 13.4%.

Hunt, L. P.↗
NASA NTRS1984

The S-web Technique for High-speed Growth of Si Sheets

The support web (S-Web) technique which was conceived as a method to grow Si-ribbons at large areal growth rates is described. A net made from carbon fibers is pulled through liquid Si. Webs of liquid Si are drawn out within the meshes of the net and kept stable by the high surface tension of liquid Si. The liquid webs crystallize some time after their formation giving a ribbon shaped body of Si at high speed. Ribbons which are suitable for the fabrication of solar cells are obtained at low pulling speeds. The results of the net pulling experiments are presented.

Grabmaier, J. G.↗
NASA NTRS1985

Advanced on-site power plant development technology program

A 30-cell stack was tested for 7200 hours. At 6000 hours the stack was successfully refilled with acid with no loss of performance. A second stack containing the advanced Configuration B cell package was fabricated and assembled for testing in 1985. A 200-kW brassboard inverter was successfully evaluated, verifying the design of the two-bridge ASCR circuit design. A fuel processing catalyst train was tested for 2000 hours verifying the catalyst for use in a 200-kW development reformer. The development reformer was fabricated for evaluation in 1985. The initial test plan was prepared for a 200-kW verification test article.

Kemp, F. S.↗
NASA NTRS1987

Fluidized-Bed Cleaning of Silicon Particles

Fluidized-bed chemical cleaning process developed to remove metallic impurities from small silicon particles. Particles (250 micrometer in size) utilized as seed material in silane pyrolysis process for production of 1-mm-size silicon. Product silicon (1 mm in size) used as raw material for fabrication of solar cells and other semiconductor devices. Principal cleaning step is wash in mixture of hydrochloric and nitric acids, leaching out metals and carrying them away as soluble chlorides. Particles fluidized by cleaning solution to assure good mixing and uniform wetting.

Rohatgi, Naresh K.↗
NASA NTRS1986

Summary of flat-plate solar array project documentation: Abstracts of published documents, 1975-1986, revision 1

Abstracts of final reports, or the latest quarterly or annual, of the Flat-Plate Solar Array (FSA) Project Contractor of Jet Propulsion Laboratory (JPL) in-house activities are presented. Also presented is a list of proceedings and publications, by author, of work connected with the project. The aim of the program has been to stimulate the development of technology that will enable the private sector to manufacture and widely use photovoltaic systems for the generation of electricity in residential, commercial, industrial, and Government applications at a cost per watt that is competitive with utility generated power. FSA Project activities have included the sponsoring of research and development efforts in silicon refinement processes, advanced silicon sheet growth techniques, higher efficiency solar cells, solar cell/module fabrication processes, encapsulation, module/array engineering and reliability, and economic analyses.

Phillips, M. J.↗
NASA NTRS1992

Flexible, Thin-Film Solar-Cell Blanket

Much of available area used to absorb solar energy. Proposed blanket of solar photovoltaic cells mounted on exterior surface of equipment it powers. Readily conforms to irregular shapes. Does not require separate supporting structure and saves space. Not added on to equipment but constitutes an integral part of it. Interconnection wiring deposited on sheet photolithographically or by other suitable masking/fabrication methods. Complete blanket, including cells and interconnections, fabricated as rigid unit directly on, and supported by, nonplanar surface to be covered.

Stella, Paul M.↗
NASA NTRS1992

ASRM test report: Autoclave cure process development

ASRM insulated segments will be autoclave cured following insulation pre-form installation and strip wind operations. Following competitive bidding, Aerojet ASRM Division (AAD) Purchase Order 100142 was awarded to American Fuel Cell and Coated Fabrics Company, Inc. (Amfuel), Magnolia, AR, for subcontracted insulation autoclave cure process development. Autoclave cure process development test requirements were included in Task 3 of TM05514, Manufacturing Process Development Specification for Integrated Insulation Characterization and Stripwind Process Development. The test objective was to establish autoclave cure process parameters for ASRM insulated segments. Six tasks were completed to: (1) evaluate cure parameters that control acceptable vulcanization of ASRM Kevlar-filled EPDM insulation material; (2) identify first and second order impact parameters on the autoclave cure process; and (3) evaluate insulation material flow-out characteristics to support pre-form configuration design.

Nachbar, D. L.↗
NASA NTRS1992

Liquid Motion in a Rotating Tank Experiment (LME)

The Liquid Motion in Rotating Tank Experiment (LME) will investigate and quantify liquid motions occurring in spin-stabilized spacecraft; acquire representative data to validate ground-test scaling procedures; and obtain scientific understanding to formulate better analytical models. LME eliminates the limitations of ground testing. LME design is nearing the end of phase B: the breadboard hardware model has been completed; the load cells have been fabricated and tested; the experiment computer has been flight qualified; and other electronics have been breadboarded. Various aspects of this experiment are presented in viewgraph form.

Dodge, F. T.↗
NASA NTRS2003

From Oxygen Generation to Metals Production: In Situ Resource Utilization by Molten Oxide Electrolysis

For the exploration of other bodies in the solar system, electrochemical processing is arguably the most versatile technology for conversion of local resources into usable commodities: by electrolysis one can, in principle, produce (1) breathable oxygen, (2) silicon for the fabrication of solar cells, (3) various reactive metals for use as electrodes in advanced storage batteries, and (4) structural metals such as steel and aluminum. Even so, to date there has been no sustained effort to develop such processes, in part due to the inadequacy of the database. The objective here is to identify chemistries capable of sustaining molten oxide electrolysis in the cited applications and to examine the behavior of laboratory-scale cells designed to generate oxygen and to produce metal. The basic research includes the study of the underlying high-temperature physical chemistry of oxide melts representative of lunar regolith and of Martian soil. To move beyond empirical approaches to process development, the thermodynamic and transport properties of oxide melts are being studied to help set the limits of composition and temperature for the processing trials conducted in laboratory-scale electrolysis cells. The goal of this investigation is to deliver a working prototype cell that can use lunar regolith and Martian soil to produce breathable oxygen along with metal by-product. Additionally, the process can be generalized to permit adaptation to accommodate different feedstock chemistries, such as those that will be encountered on other bodies in the solar system. The expected results of this research include: (1) the identification of appropriate electrolyte chemistries; (2) the selection of candidate anode and cathode materials compatible with electrolytes named above; and (3) performance data from a laboratory-scale cell producing oxygen and metal. On the strength of these results it should be possible to assess the technical viability of molten oxide electrolysis for in situ resource utilization on the Moon and Mars. In parallel, there may be commercial applications here on earth, such as new green technologies for metals extraction and for treatment of hazardous waste, e.g., fixing heavy metals.

Khetpal, Deepak↗
NASA NTRS1989

Thin film memory matrix using amorphous and high resistive layers

Memory cells in a matrix are provided by a thin film of amorphous semiconductor material overlayed by a thin film of resistive material. An array of parallel conductors on one side perpendicular to an array of parallel conductors on the other side enable the amorphous semiconductor material to be switched in addressed areas to be switched from a high resistance state to a low resistance state with a predetermined level of electrical energy applied through selected conductors, and thereafter to be read out with a lower level of electrical energy. Each cell may be fabricated in the channel of an MIS field-effect transistor with a separate common gate over each section to enable the memory matrix to be selectively blanked in sections during storing or reading out of data. This allows for time sharing of addressing circuitry for storing and reading out data in a synaptic network, which may be under control of a microprocessor.

Thakoor, Anilkumar P.↗
DOE OSTI2020

A Sub-Threshold Low-Power Integrated Bandpass Filter for Highly-Integrated Spectrum Analyzers

Low-power analog filter banks provide frequency analysis with minimal power and space requirements, making them viable solutions for integrated remote audio- and vibration-sensing applications. Compared with their digital counterparts, analog filter banks are better suited to achieve the lower power consumption necessary for IoT applications. In this work, the design and implementation of a sub-threshold complementary metal-oxide semiconductor (CMOS) integrated low-power tunable bandpass filter channel for signal spectrum analysis and signal discrimination is presented, including performance improvements to stability and precise matching between filter stages. The 8 th -order filter channel achieves an effective Q-factor of 4.5 and dynamic range of 60 dB, has an operational frequency range from 2 kHz to 100 kHz, and consumes 256 µW nominally at the highest center frequency. An integrated analog Gm-C filter topology is selected for this application. Functionally, the high-Q bandpass filter transfer function is implemented via four cascaded 2 nd -order filter cells and is fabricated in 130-nm 1.2-V CMOS technology, making it suitable for use in monolithic integrated spectral analysis (MISA) applications.

Long, Gavin↗
DOE OSTI2022

MEA Manufacturing R&D

This is our annual presentation on the HFTO-funded MEA Manufacturing R&D project, mainly focused on development of in-line quality inspection methods for high volume fabrication of fuel cell and electrolysis MEA materials.

DIRECT ENERGY CONVERSION,ENGINEERING↗
NASA NTRS1976

Solid polymer electrolyte (SPE) fuel cell technology program, phase 2/2A

Test evaluations were performed on a fabricated single solid polymer electrolyte cell unit. The cell operated at increased current density and at higher performance levels. This improved performance was obtained through a combination of increased temperature, increased reactant pressures, improved activation techniques and improved thermal control over the baseline cell configuration. The cell demonstrated a higher acid content membrane which resulted in increased performance. Reduced catalyst loading and low cost membrane development showed encouraging results.

Source record↗