Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Longitudinal compressive failure modes in fiber composites End attachment effects on IITRI type test specimens

The end-attachment effects on longitudinal compressive strength of IITRI type specimen unidirectional fiber composites are formally assessed using finite-element analysis (FEA) in conjunction with composite mechanics. Sixteen different cases were analyzed to evaluate end-attachment effects (such as degree of misalignment, type of misalignment, progressive end-tab debonding, and specimen thickness) on stress distribution, peak stresses, buckling loads, and buckling mode shapes. The results obtained from the FEA and comparisons with fractured specimens show that eccentricities induce bending-type stresses which peak near the end-tabs and cause flexural type fracture. Also, guidelines are included for placing back-to-back strain gages to measure the presence/absence of possible end-attachment and eccentricity effects.

Chamis, C. C.↗

Bursting at the Seams: Rippled Monolayer Bismuth on NbSe 2

Bismuth, one of the heaviest semimetals in nature, ignited the interest of the materials-physics community for its potential impact on topological quantum-material systems that utilize its strong spin-orbit coupling (SOC) and unique orbital hybridization. In particular, recent theoretical predictions of unique topological and superconducting properties of thin bismuth films and interfaces prompted intense research on the growth of sub- to a few monolayers of bismuth on different substrates. Similar to bulk rhombohedral bismuth, the initial growth of bismuth films on most substrates results in buckled bilayers that either grow in the (111) or (110) directions, with a lattice constant close to that of bulk Bi. By contrast, in this paper we show a new growth pattern for bismuth monolayers on NbSe 2 . We find that the initial growth of Bi can form a strongly bonded commensurate layer, resulting in a compressively strained two-dimensional triangular lattice. A unique pattern of 1D ripples and domain walls is observed. The single layer of bismuth also introduces strong marks on the electronic properties at the surface.

36 MATERIALS SCIENCE↗

Importance of anisotropy on design of compression-loaded composite corrugated panels

An investigation is conducted of the importance of anisotropic terms in the design of composite corrugated panels, for a range of axial compressive load intensities. The two panel configurations treated were panels with tailored laminates and panels with a continuous laminate; both are of interest to aircraft designers and prone to anisotropic effects which are of as-yet undetermined extent. The importance of the anisotropic terms is measured by the difference between the design load and the buckling load obtained from the ultimate structural analysis.

Gurdal, Zafer↗

Structural Evaluation of Exo-Skeletal Engine Fan Blades

The available computational simulation capability is used to demonstrate the structural viability of composite fan blades of innovative Exo-Skeletal Engine (ESE) developed at NASA Glenn Research Center for a subsonic mission. Full structural analysis and progressive damage evaluation of ESE composite fan blade is conducted through the NASA in-house computational simulation software system EST/BEST. The results of structural assessment indicate that longitudinal stresses acting on the blade are in compression. At a design speed of 2000 rpm, pressure and suction surface outer most ply stresses in longitudinal, transverse and shear direction are much lower than the corresponding composite ply strengths. Damage is initiated at 4870 rpm and blade fracture takes place at rotor speed of 7735 rpm. Damage volume is 51 percent. The progressive damage, buckling, stress and strength results indicate that the design at hand is very sound because of the factor of safety, damage tolerance, and buckling load of 6811 rpm.

Kuguoglu, Latife↗

Compressive Strength of Stainless-Steel Sandwiches at Elevated Temperatures

Experimental results are presented from crippling tests of stainless-steel sandwich specimens in the temperature range from 80 F to 1,200 F. The specimens included resistance-welded 17-7 PH stainless-steel sandwiches with single-corrugated cores, type 301 stainless-steel sandwiches with double-corrugated cores, and brazed 17-7 PH stainless-steel sandwiches with honeycomb cores. The experimental strengths are compared with predicted buckling and crippling strengths. The crippling strengths were predicted from the calculated maximum strength of the individual plate elements of the sandwiches and from a correlation procedure which gives the elevated-temperature crippling strength when the experimental room-temperature crippling strengths are known. Photographs of some of the tested specimens are included to show the modes of failure.

Mathauser, Eldon E.↗

Composite Fan Blade Design for Advanced Engine Concepts

The aerodynamic and structural viability of composite fan blades of the revolutionary Exo-Skeletal engine are assessed for an advanced subsonic mission using the NASA EST/BEST computational simulation system. The Exo-Skeletal Engine (ESE) calls for the elimination of the shafts and disks completely from the engine center and the attachment of the rotor blades in spanwise compression to a rotating casing. The fan rotor overall adiabatic efficiency obtained from aerodynamic analysis is estimated at 91.6 percent. The flow is supersonic near the blade leading edge but quickly transitions into a subsonic flow without any turbulent boundary layer separation on the blade. The structural evaluation of the composite fan blade indicates that the blade would buckle at a rotor speed that is 3.5 times the design speed of 2000 rpm. The progressive damage analysis of the composite fan blade shows that ply damage is initiated at a speed of 4870 rpm while blade fracture takes place at 7640 rpm. This paper describes and discusses the results for the composite blade that are obtained from aerodynamic, displacement, stress, buckling, modal, and progressive damage analyses. It will be demonstrated that a computational simulation capability is readily available to evaluate new and revolutionary technology such as the ESE.

Abumeri, Galib H.↗

Degradation by Kinking in Layered Cathode Materials

Layered cathode materials are commonly used in lithium and sodium ion batteries, but they are prone to degradation under electrochemical cycling during battery operation. Here we report a new type of degradation mechanism through the electrochemically induced mechanical buckling and delamination cracking of intercalation layers in a P2 Na 0.7 -Ni 0.3 Mn 0.6 Co 0.1 O 2 (Na-NMC) cathode material. Kinks form in the delaminated layers due to severe local bending, and each kink consists of a vertical array of dislocations, resulting from an easy slip between transition metal oxide layers. In situ mechanical compression experiments directly reveal the kink formation due to strong mechanical anisotropy parallel and perpendicular to the intercalation layers in single-crystal Na-NMC. In situ electrochemical experiments indicate that kinks form during the desodiation process. Our results unveil a new mechanism of electrochemically induced mechanical degradation stemming from weak interlayer bonding in layered cathode materials. In conclusion, this work has broad implications for the mitigation of degradation associated with irreversible interlayer slip in layered cathode materials.

25 ENERGY STORAGE↗

Postbuckling of long orthotropic plates in combined shear and compression

The nonlinear large-deflection partial differential equations of von karman for orthotropic plates loaded in combined shear and compression are converted into a set of first-order nonlinear ordinary differential equations by assuming trigonometric functions in one direction. These equations are solved numerically using a two point boundary problem solver which makes use of Newton's method. Results are obtained which determine the postbuckling behavior of rectangular plates with loading up to about three times the buckling load. Both isotropic and orthotropic composite plates are considered. Results show that orthotropic plates may behave quite differently than isotropic plates and that in-plane boundary conditions are important for plates loaded in shear.

Stein, M.↗

Elastic Instability of Members Having Sections Common in Aircraft Construction

Two fundamental problems of elastic stability are discussed in this report. In part one formulas are given for calculating the critical stress at which a thin, outstanding flange of a compression member will either wrinkle into several waves or form into a single half wave and twist the member about its longitudinal axis. A mathematical study of the problem, which together with experimental work has led to these formulas, is given in an appendix. Results of test substantiating the recommended formulas are also presented. In part two the lateral buckling of beams is discussed. The results of a number of mathematical studies of this phenomenon have been published prior to this writing, but very little experimentally determined information relating to the problem has been available heretofore. Experimental verification of the mathematical deductions is supplied.

Trayer, George W↗

Defect sensitivity of filament-wound structures in compression

Compression testing of 12-ply graphite/bismaleimide laminated plates with induced and natural defects is discussed, and emphasis is placed on resultant changes in strength and stiffness. Ply drops, ply cuts, and fiber crossovers are studied by comparison with a quasi-isotropic control group. It is observed that, as expected, failure initiates at the defects and progresses via delamination, sublaminate buckling, angle-ply cracking, and longitudinal ply failure. The ultimate stress is reduced by approximately 40 percent for all types of defects except the unsymmetrical cut-ply specimens which averages a 54-percent reduction. The average stiffness reduction of 10 percent is observed for specimens with induced defects. Fiber crossovers are found to reduce the laminate strength and stiffness significantly.

Jensen, David W.↗

Charts for the minimum-weight design of 24s-t aluminum-alloy flat compression panels with longitudinal z-section stiffeners

Design charts are developed for 24s-t aluminum-alloy flat compression panels with longitudinal z-section stiffeners. These charts make possible the design of the lightest panels of this type for a wide range of design requirements. Examples of the use of the charts are given and it is pointed out on the basis of these examples that, over a wide range of design conditions, the maintenance of buckle-free surfaces does not conflict with the achievement of high structural efficiency. The achievement of the maximum possible structural efficiency with 24s-t aluminum-alloy panels, however, requires closer stiffener spacings than those now in common use.

Schuette, Evan H↗

Vibration of compressively loaded shear deformable flat panels exhibiting initial geometric imperfections

Numerical study results are presented which indicate that, in the prebuckling range, the natural frequency predicted by the shear-deformable plate theory is smaller than that associated with its transverse-shear rigid counterpart. The opposite behavior occurs in the postbuckling/postcritical range. With increasing transverse shear flexibility, greater differences between frequencies predicted by shear deformation and infinitely rigid transverse shear theories emerge. The character of in-plane boundary conditions is a determinant of both increasing/decreasing buckling loads and increasing/decreasing vibratory frequencies.

Librescu, L.↗

Postbuckling behavior of selected flat stiffened graphite-epoxy panels loaded in compression

Results of an experimental study of the postbuckling behavior of selected flat stiffened graphite-epoxy panels loaded in compression are presented. The postbuckling response and failure characteristics of undamaged panels and panels damaged by low-speed impact are described. Each panel had four equally-spaced I-spaced stiffeners and 16- or 24-ply quasi-isotropic skins. Panels with three different stiffener spacings were tested. Some undamaged specimens supported as much as three times their initial buckling load before failing. Failure of all panels initiated in a skin-stiffener interface region. Analytical results obtained from a nonlinear general shell finite element analysis computer code correlate well with typical postbuckling test results up to failure. The analytical modeling detail necessary to predict accurately the response of a panel is described. Test results show that low-speed impact damage can reduce the postbuckling strength of a stiffened panel and that the skin-stiffener interface region is more sensitive to impact damage than the skin midway between stiffeners.

Starnes, J. H., Jr.↗

Sensitivity of buckling loads of anisotropic shells of revolution to geometric imperfections and design changes

Buckling load sensitivity calculations in the shell-of-revolution program FASOR are discussed. This development is based on Koiter's initial postbuckling theory, which has been generalized to include the effect of stiffness changes, as well as geometric imperfections. The implementation in FASOR is valid for anisotropic, as well as orthotropic, shells. Examples are presented for cylindrical panels under axial compression, complete cylindrical shells in torsion, and antisymmetric angle-ply cylindrical panels under edge shear.

Cohen, Gerald A.↗

A method for the geometrically nonlinear analysis of compressively loaded prismatic composite structures

A method was developed for the geometrically nonlinear analysis of the static response of thin-walled stiffened composite structures loaded in uniaxial or biaxial compression. The method is applicable to arbitrary prismatic configurations composed of linked plate strips, such as stiffened panels and thin-walled columns. The longitudinal ends of the structure are assumed to be simply supported, and geometric shape imperfections can be modeled. The method can predict the nonlinear phenomena of postbuckling strength and imperfection sensitivity which are exhibited by some buckling-dominated structures. The method is computer-based and is semi-analytic in nature, making it computationally economical in comparison to finite element methods. The method uses a perturbation approach based on the use of a series of buckling mode shapes to represent displacement contributions associated with nonlinear response. Displacement contributions which are of second order in the model amplitudes are incorported in addition to the buckling mode shapes. The principle of virtual work is applied using a finite basis of buckling modes, and terms through the third order in the model amplitudes are retained. A set of cubic nonlinear algebraic equations are obtained, from which approximate equilibrium solutions are determined. Buckling mode shapes for the general class of structure are obtained using the VIPASA analysis code within the PASCO stiffened-panel design code. Thus, subject to some additional restrictions in loading and plate anisotropy, structures which can be modeled with respect to buckling behavior by VIPASA can be analyzed with respect to nonlinear response using the new method. Results obtained using the method are compared with both experimental and analytical results in the literature. The configurations investigated include several different unstiffened and blade-stiffening panel configurations, featuring both homogeneous, isotropic materials, and laminated composite material.

Stoll, Frederick↗

Comparison of the compressive strengths for stitched and toughened composite systems

The compression strength of a stitched and a toughened matrix graphite/epoxy composite was determined and compared to a baseline unstitched untoughened composite. Two different layups with a variety of test lengths were tested under both ambient and hot/wet conditions. No significant difference in strength was seen for the different materials when the gage lengths of the specimens were long enough to lead to a buckling failure. For shorter specimens, a 30 percent reduction in strength from the baseline was seen due to stitching for both a 48-ply quasi-isotropic and a (0/45/0/-45/90/-45/0/45/0)s laminate. Analysis of the results suggested that the decrease in strength was due to increased fiber misalignment due to the stitches. An observed increasing strength with decreasing gage length, which was seen for all materials, was explained with a size effect model. The model assumed a random distribution of flaws (misaligned fibers). The toughened materials showed a small increase in strength over the baseline material for both laminates presumably due to the compensating effects of a more compliant matrix and straighter fibers in the toughened material. The hot/wet strength of the stitched and baseline material fell 30 percent below their ambient strengths for shorter, nonbuckling specimen, while the strength of the toughened matrix material only fell 20 percent. Video images of the failing specimen were recorded and showed local failures prior to global collapse of the specimen. These images support the theory of a random distribution of flaws controlling composite failure. Failed specimen appearance, however, seems to be a misleading indication of the cause of failure.

Reeder, James R.↗

Comparison of the Compressive Strengths for Stitched and Toughened Composite Systems

The compression strength of a stitched and a toughened matrix graphite/epoxy composite was determined and compared to a baseline unstitched untoughened composite. Two different layups with a variety of test lengths were tested under both ambient and hot/wet conditions. No significant difference in strength was seen for the different materials when the gage lengths of the specimens were long enough to lead to a buckling failure. For shorter specimens, a 30% reduction in strength from the baseline was seen due to stitching for both a 48-ply quasi-isotropic and a (0/45/0/-45/90/-45/0/45/0)s laminate. Analysis of the results suggested that the decrease in strength was due to increased fiber misalignment due to the stitches. An observed increasing strength with decreasing gage length, which was seen for all materials, was explained with a size effect model. The model assumed a random distribution of flaws (misaligned fibers). The toughened material showed a small increase in strength over the baseline material for both laminates presumably due to the compensating effects of a more compliant matrix and straighter fibers in the toughened material. The hot/wet strength of the stitched and baseline material fell 30% below their ambient strengths for shorter, non-buckling specimen, while the strength of the toughened matrix material only fell 20%. Video images of the failing specimen were recorded and showed local failures prior to global collapse of the specimen. These images support the theory of a random distribution of flaws controlling composite failure. Failed specimen appearance however, seems to be a misleading indication of the cause of failure.

Reeder, James R.↗

Scalability in SLA lattice through lattice orientation and hybrid frame and plate architectures

Lightweighting has been a key goal for engineers and designers, with lattice structures widely explored as the building blocks for structural components. Cellular structure-inspired lattice truss frame designs made of struts, have been extensively studied. All plate-based lattice designs have superior mechanical performance. Limits in scalability occur from formation of closed pockets limiting uv curing in processes like stereolithography (SLA). We examine hybrid frame and plate body-centered cubic-simply cubic (BCC-SC) lattices under compression. Unit cells and scaled up lattice exhibit an increase in yield stress and modulus with the addition of plates. The loading direction on the hybrid frame and plate unit cells affected the magnitude of improvement. Simulations and measurements indicated that the optimal lightweight lattice was determined to be when two plates were placed opposite each other with plates buttressing the struts, inhibiting buckling of the struts aligned with the loading direction. This lattice resulted in 63% improvement in specific modulus, a 137% improvement in specific yield point, and a 360% improvement in specific energy absorption (SEA) and the scaled up 4 × 4 × 4 scaled-up structures, showed a 107%, 148%, and 297% in specific modulus, specific yield point, and SEA, respectively A combined stretching-bending behavior was identified in optimal orientations reflecting the delayed buckling mechanism paired to a rising stress-strain curve past the elastic yield indicating bending resistance. The mass moment of inertia was found to be a key parameter correlating optimum orientation for the same number of plates added to the BCC-SC frame.

Mahan Ghosh↗