SEARCH · Engineering Papers

Results for “Beam Forming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Tunable Optical True-Time Delay Devices Would Exploit EIT

Tunable optical true-time delay devices that would exploit electromagnetically induced transparency (EIT) have been proposed. Relative to prior true-time delay devices (for example, devices based on ferroelectric and ferromagnetic materials) and electronically controlled phase shifters, the proposed devices would offer much greater bandwidths. In a typical envisioned application, an optical pulse would be modulated with an ultra-wideband radio-frequency (RF) signal that would convey the information that one seeks to communicate, and it would be required to couple differently delayed replicas of the RF signal to the radiating elements of a phased-array antenna. One or more of the proposed devices would be used to impose the delays and/or generate the delayed replicas of the RF-modulated optical pulse. The beam radiated or received by the antenna would be steered by use of a microprocessor-based control system that would adjust operational parameters of the devices to tune the delays to the required values. EIT is a nonlinear quantum optical interference effect that enables the propagation of light through an initially opaque medium. A suitable medium must have, among other properties, three quantum states (see Figure 1): an excited state (state 3), an upper ground state (state 2), and a lower ground state (state 1). These three states must form a closed system that exhibits no decays to other states in the presence of either or both of two laser beams: (1) a probe beam having the wavelength corresponding to the photon energy equal to the energy difference between states 3 and 1; and (2) a coupling beam having the wavelength corresponding to the photon energy equal to the energy difference between states 3 and 2. The probe beam is the one that is pulsed and modulated with an RF signal.

Kulikov, Igor↗

NASA NTRS1975

ISOFINEL: Isoparametric finite element code for elastic analysis of two-dimensional bodies

A formulation is presented for the development of a finite element program for the elastic analysis of two-dimensional bodies using the eight-node isoparametric quadrilateral. The program solves for both plane stress and plane strain problems. The finite element formulation based on the isoparametric displacement functions is presented. The program structure is given in the form of flow diagrams with descriptions of the numerical procedure used to obtain the element stiffness matrix, and the solution method employed to solve for nodal displacements. Three numerical examples (a plate under uniaxial tension, a plate under pure shear, and a beam under pure bending) are presented to illustrate the capability and limitations of the element implementation. The first problem is solved exactly by the element, as predicted by the form of its displacement functions. In the other two problems the accuracy of the solution is highly dependent upon the slenderness of the element, the number of elements in the map, and the numerical integration scheme used to build the element stiffness matrix.

Marino, C.↗

NASA NTRS1983

Nitriding of titanium and titanium: 8 percent aluminum, 1 percent molybdenum, 1 percent vanadium alloy with an ion-beam source

Titanium and Ti-8Al-1Mo-1V alloy were nitrided with an ion-beam source of nitrogen or argon and nitrogen at a total pressure of 2 x 10 to the minus 4th power to 10 x 10 to the minus 4th power torr. The treated surface was characterized by surface profilometry, X-ray diffractometry, Auger electron spectroscopy and microhardness measurements. The tetragonal Ti2N phase formed in pure titanium and Ti-8Al-1Mo-1V alloy with traces of AlN in the alloy. Two opposite processes competed during the ion-beam-nitriding process: (1) formation of nitrides in the surface layer and (2) sputtering of the nitrided layers by the ion beam. The highest surface hardnesses, about 500 kg/sq mm in titanium and 800 kg/sq mm in Ti-8Al-1Mo-1V, were obtained by ion nitriding with an ion beam of pure nitrogen at 4.2 x 10 to the minus 4th power torr at a beam voltage of 1000 V.

Gill, A.↗

NASA NTRS2005

Atomic Clock Based on Opto-Electronic Oscillator

A proposed highly accurate clock or oscillator would be based on the concept of an opto-electronic oscillator (OEO) stabilized to an atomic transition. Opto-electronic oscillators, which have been described in a number of prior NASA Tech Briefs articles, generate signals at frequencies in the gigahertz range characterized by high spectral purity but not by longterm stability or accuracy. On the other hand, the signals generated by previously developed atomic clocks are characterized by long-term stability and accuracy but not by spectral purity. The proposed atomic clock would provide high spectral purity plus long-term stability and accuracy a combination of characteristics needed to realize advanced developments in communications and navigation. In addition, it should be possible to miniaturize the proposed atomic clock. When a laser beam is modulated by a microwave signal and applied to a photodetector, the electrical output of the photodetector includes a component at the microwave frequency. In atomic clocks of a type known as Raman clocks or coherent-population-trapping (CPT) clocks, microwave outputs are obtained from laser beams modulated, in each case, to create two sidebands that differ in frequency by the amount of a hyperfine transition in the ground state of atoms of an element in vapor form in a cell. The combination of these sidebands produces a transparency in the population of a higher electronic level that can be reached from either of the two ground-state hyperfine levels by absorption of a photon. The beam is transmitted through the vapor to a photodetector. The components of light scattered or transmitted by the atoms in the two hyperfine levels mix in the photodetector and thereby give rise to a signal at the hyperfine- transition frequency. The proposed atomic clock would include an OEO and a rubidium- or cesium- vapor cell operating in the CPT/Raman regime (see figure). In the OEO portion of this atomic clock, as in a typical prior OEO, a laser beam would pass through an electro-optical modulator, the modulated beam would be fed into a fiber-optic delay line, and the delayed beam would be fed to a photodetector. The electrical output of the photodetector would be detected, amplified, filtered, and fed back to the microwave input port of the modulator. The laser would be chosen to have the same wavelength as that of the pertinent ground-state/higher-state transition of the atoms in the vapor. The modulator/ filter combination would be designed to operate at the microwave frequency of the hyperfine transition. Part of the laser beam would be tapped from the fiberoptic loop of the OEO and introduced into the vapor cell. After passing through the cell, this portion of the beam would be detected differentially with a tapped portion of the fiber-optically-delayed beam. The electrical output of the photodetector would be amplified and filtered in a loop that would control a DC bias applied to the modulator. In this manner, the long-term stability and accuracy of the atomic transition would be transferred to the OEO.

Maleki, Lute↗

NASA NTRS1972

The atom-molecule reaction D plus H2 yields HD plus H studied by molecular beams

Collisions between deuterium atoms and hydrogen molecules were studied in a modulated crossed beam experiment. The relative signal intensity and the signal phase for the product HD from reactive collisions permitted determination of both the angular distribution and HD mean velocity as a function of angle. From these a relative differential reactive scattering cross section in center-of-mass coordinates was deduced. The experiment indicates that reactively formed HD which has little or no internal excitation departs from the collision anisotropically, with maximum amplitude 180 deg from the direction of the incident D beam in center-of-mass coordinates, which shows that the D-H-H reacting configuration is short-lived compared to its rotation time. Non reactive scattering of D by H2 was used to assign absolute values to the differential reactive scattering cross sections.

Geddes, J.↗

NASA NTRS1992

Constrained modes in control theory - Transmission zeros of uniform beams

Mathematical arguments are presented demonstrating that the well-established control system concept of the transmission zero is very closely related to the structural concept of the constrained mode. It is shown that the transmission zeros of a flexible structure form a set of constrained natural frequencies for it, with the constraints depending explicitly on the locations and the types of sensors and actuators used for control. Based on this formulation, an algorithm is derived and used to produce dimensionless plots of the zero of a uniform beam with a compatible sensor/actuator pair.

Williams, T.↗

NASA NTRS1984

Improved Beam Theory for Anisotropic Materials

The behavior of beams made of anisotropic material was investigated in order to develop an appropriate model of such behavior. Closed form solutions of the problem were derived using two alternative approaches. In the first approach, the axial displacements are expanded as a series of eigenwarpings. In the second approach, the axial stresses are expanded as a series of eigenwarpings. A finite element solution was also derived using the same displacement field as in the first approach.

Source record↗

NASA NTRS1985

A ground-based experimental test program to duplicate and study the spacecraft glow phenomenon

The use of a plasma device, the Advanced Concepts Torus-I, for producing atoms and molecules to study spacecraft glow mechanisms is discussed. A biased metal plate, located in the plasma edge, is used to accelerate and neutralize plasma ions, thus generating a neutral beam with a flux approx. 5 x 10 to the 14th power/sq cm/sec at the end of a drift tube. Our initial experiments are to produce a 10 eV molecular and atomic nitrogen beam directed onto material targets. Photon emission in the spectral range 2000 to 9000 A from excited species formed on the target surface will be investigated.

Langer, W. D.↗

NASA NTRS1986

The real-time use of wind profilers in nowcasting

The program for Regional Observing and Forecasting Services (PROFS) has been using wind profile data in experimental forecast applications for over two years, mostly in the form of real-time color displays on the PROFS forecast workstation. The most ambitious test of the workstation to date, the 1985 PROFS Real-Time Experiment (RT-85), ran from 15 May to 23 August, 1985. The use of wind profiler products during this and previous experiments is described. Data from the experimental profiler network in Colorado and from the profiler in Oklahoma are in the form of hourly averages. Arriving data frequently contain errors whose origins range from interference by aircraft in the beams to highway truck traffic. Most of the irregularities are apparent through visual inspection of profiler wind observations plotted on a time-height cross section, but this method of quality control is inadequate if the intended uses of the data involve numerical calculations.

Smith, T. L.↗

NASA NTRS1988

Loss of Gaussian beams through off-axis circular apertures

An attempt is made to solve the problem of the loss caused in a Gaussian beam by an off-axis circular aperture. Although in general the problem cannot be solved in closed form, three special cases are considered. If the offset is zero, the limit of the radial integration coincides with the radius of the circular aperture; in this case, the integration over the angular variable can be performed in closed form. In a second special case, an analytical expression can be obtained when the offset is small. A third special case occurs when the offset is large and equals the aperture radius.

Barnes, Norman P.↗

NASA NTRS1989

Minimum attainable RMS attitude error using co-located rate sensors

A closed form analytical expression for the minimum attainable attitude error (as well as the error rate) in a flexible beam by feedback control using co-located rate sensors is announced. For simplicity, researchers consider a beam clamped at one end with an offset mass (antenna) at the other end where the controls and sensors are located. Both control moment generators and force actuators are provided. The results apply to any beam-like lattice-type truss, and provide the kind of performance criteria needed under CSI - Controls-Stuctures-Integrated optimization.

Balakrishnan, A. V.↗

NASA NTRS1995

Models for classical gamma-ray bursts

The origin of gamma-ray bursts continues to be a great mystery. Here we review some relevant observations and a number of recent models. While no clear solution exists at the present time, the parameter space for Galactic halo models is becoming very constrained. Cosmological models on the other hand require both enormous total energy and the concentration of that energy into a small mass. This implies compact objects, probably accreting black holes of stellar size. We review some of the physics of such accreting black holes and point out that the jet formed from accretion into a rapidly accreting black hole of stellar mass might precess. This precession, coupled to beaming, could impose additional time structure on the burst and its spectrum. In the event of a 'failed' supernova model, the wind of the Wolf-Rayet star prior to the event could provide the beam dump where the jet generates gamma-rays. Enduring emission that grows harder with time might be expected for several hours as the density in the vicinity of the black hole declines.

Hartmann, D. H.↗

NASA NTRS2003

Using Plate Finite Elements for Modeling Fillets in Design, Optimization, and Dynamic Analysis

A methodology has been developed that allows the use of plate elements instead of numerically inefficient solid elements for modeling structures with 90 degree fillets. The technique uses plate bridges with pseudo Young's modulus (Eb) and thickness (tb) values placed between the tangent points of the fillets. These parameters are obtained by solving two nonlinear simultaneous equations in terms of the independent variables rlt and twallt. These equations are generated by equating the rotation at the tangent point of a bridge system with that of a fillet, where both rotations are derived using beam theory. Accurate surface fits of the solutions are also presented to provide the user with closed-form equations for the parameters. The methodology was verified on the subcomponent level and with a representative filleted structure, where the technique yielded a plate model exhibiting a level of accuracy better than or equal to a high-fidelity solid model and with a 90-percent reduction in the number of DOFs. The application of this method for parametric design studies, optimization, and dynamic analysis should prove extremely beneficial for the finite element practitioner. Although the method does not attempt to produce accurate stresses in the filleted region, it can also be used to obtain stresses elsewhere in the structure for preliminary analysis. A future avenue of study is to extend the theory developed here to other fillet geometries, including fillet angles other than 90 and multifaceted intersections.

Brown, A. M.↗

NASA NTRS2004

Model of a Piezoelectric Transducer

It's difficult to control liquid and gas in propellant tanks in zero gravity. A possible a design would utilize acoustic liquid manipulation (ALM) technology which uses ultrasonic beams conducted through a liquid and solid media, to push gas bubbles in the liquid to desirable locations. We can propel and control the bubble with acoustic radiation pressure by aiming the acoustic waves on the bubble s surface. This allows us to design a so called smart tank in which the ALM devices transfer the gas to the outer wall of the tank and isolating the liquid in the center. Because the heat transfer rate of a gas is lower of that of the liquid it would substantially decrease boil off and provide of for a longer storage life. The ALM beam is composed of little wavelets which are individual waves that constructively interfere with each other to produce a single, combined acoustic wave front. This is accomplished by using a set of synchronized ultrasound transducers arranged in an array. A slight phase offset of these elements allows us to focus and steer the beam. The device that we are using to produce the acoustic beam is called the piezoelectric transducer. This device converts electrical energy to mechanical energy, which appears in the form of acoustic energy. Therefore the behavior of the device is dependent on both the mechanical characteristics, such as its density, cross-sectional area, and its electrical characteristics, such as, electric flux permittivity and coupling factor. These devices can also be set up in a number of modes which are determined by the way the piezoelectric device is arranged, and the shape of the transducer. For this application we are using the longitudinal or thickness mode for our operation. The transducer also vibrates in the lateral mode, and one of the goals of my project is to decrease the amount of energy lost to the lateral mode. To model the behavior of the transducers I will be using Pspice, electric circuit modeling tool, to determine the transducer's electrical characteristics at the frequency of interest. This will also help me determine the characteristics of an impedance matching network to operate the transducer at its optimum efficiency. For this I will use ABMs (analog behavioral modeling) to model dependent current and voltage sources that represent the transducer. I have also been working on the Labview control software for the phased array used to control the bubbles, and will begin testing on that before the end of my internship.

Goodenow, Debra↗

NASA NTRS2003

Inverse Tomo-Lithography for Making Microscopic 3D Parts

According to a proposal, basic x-ray lithography would be extended to incorporate a technique, called inverse tomography, that would enable the fabrication of microscopic three-dimensional (3D) objects. The proposed inverse tomo-lithographic process would make it possible to produce complex shaped, submillimeter-sized parts that would be difficult or impossible to make in any other way. Examples of such shapes or parts include tapered helices, paraboloids with axes of different lengths, and even Archimedean screws that could serve as rotors in microturbines. The proposed inverse tomo-lithographic process would be based partly on a prior microfabrication process known by the German acronym LIGA (lithographie, galvanoformung, abformung, which means lithography, electroforming, molding). In LIGA, one generates a precise, high-aspect ratio pattern by exposing a thick, x-ray-sensitive resist material to an x-ray beam through a mask that contains the pattern. One can electrodeposit metal into the developed resist pattern to form a precise metal part, then dissolve the resist to free the metal. Aspect ratios of 100:1 and patterns into resist thicknesses of several millimeters are possible.

White, Victor↗

NASA NTRS2018

Investigating Variations in Water Abundances in Lunar Felsite Clasts Using Coordinated Field-Emission STEM and NanoSIMS Analyses

As representatives of petrochemically-evolved igneous rocks on the Moon, the granitic felsite clasts in lunar breccias have come under renewed focus as part of new efforts to use feldspars for assessing the inventory of lunar water and other volatiles. Previous petrologic studies of these clasts were tilted towards finding those assemblages and relationships most likely to be direct products of magmatic processes. In support of our on-going NanoSIMS (Nanoscale Secondary Ion Mass Spectrometry) measurements of trace water contents in the feldspars in these clasts, we are using coordinated analytical SEM (Scanning Electron Microscopy), electron probe microanalyzer (EPMA) and analytical field emission scanning transmission electron microscopy (FE-STEM) techniques to re-evaluate the full diversity of processes under which the feldspar-bearing assemblages in these clasts formed. Here we report a comparison of FE-STEM imaging and microanalysis results obtained on focused ion beam (FIB) sections extracted from felsite (alkali feldspar plus SiO2 plus or minus plagioclase) clasts in lunar breccias 15405 and 12013. The feldspars in these clasts have water contents which, although relatively low (7-18 ppm) by terrestrial standards, still show values significantly higher than measurements (approximately 0.5 ppm) of nominally anhydrous NanoSIMS standards.

Christoffersen, Roy↗

NASA NTRS1986

An electromagnetic/electrostatic dual cathode system for electron beam instruments

A method of providing cathode redundancy which consists of two fixed cathodes and uses electromagnetic and/or electrostatic fields to direct the electron beam to the electron optical axis is presented, with application to the cathode system of the Scanning Electron Microscope and Particle Analyzer proposed for NASA's Mariner Mark II Comet Rendezvous/Asteroid Flyby projected for the 1990s. The symmetric double deflection system chosen has the optical property that the image of the effective electron source is formed above the magnet assembly near the apparent position of the effective source, and it makes the transverse positions of the electron sources independent of the electron beam energy. Good performance of the system is found, with the sample imaging resolution being the same as for the single-axis cathode.

Bradley, J. G.↗

NASA NTRS1977

VIZIR: The SEP high resolution laser beam recorder

A means for high density archiving of meteorological data on a photographic film is described. The data are stored on-line under a form accessible to interpretation. The VIZIR thus forms the final link of the receiving system of a ground station.

Salter, M. L.↗