Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BURNUP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

MESOSCALE THERMAL TRANSPORT MEASUREMENTS OF MULTI-PHASE AND POROUS NUCLEAR FUELS USING A SQUARE-WAVE PULSE THERMOREFLECTANCE TECHNIQUE

The safe and efficient operation of nuclear reactors require accurate knowledge of peak temperatures in the fuel assemblies. The temperature profiles are governed by the thermal transport properties of the fuel, namely the thermal conductivities (k) and thermal diffusivities (D). These values can be very difficult to measure as they are known to vary considerably from the measured bulk values of the fresh fuel, and quickly degrade with increasing burnup [1 -3] . Laser-based techniques have been effectively used for non-destructive and non-contact thermal transport measurements of a wide variety of materials, including nuclear materials [4-6] that would otherwise prove too hazardous or difficult to measure otherwise. In this study, a new thermoreflectance technique known as square-pulse transient thermoreflectance (SPTR) is described and used to determine the mesoscale thermal diffusivity of both uranium sesquisilicide (U3Si2) and uranium nitride (UN) phases in a composite fuel with micron level spatial resolution [7]. This technique employs a rapid train of square-wave pulses from an excitation laser to create a periodic heat flux on a gold coated sample surface. Surface adsorption results in transient film temperatures and hence rapid fluctuations in thermoreflectance that can be measured via a detection laser coupled with a digital oscilloscope. The lasers are coaxially focused on the sample surface, allowing for a sample measurement area of a single convolved laser spot size (~2 µm). A sensitivity analysis was conducted to identify key measurement parameters of this technique using reference materials with a range of thermal conductivities comparable to those of both ceramic, composite, and metal nuclear fuel types (1.4 – 27.2 W/m-K). The reference materials were measured using the new technique as well as a spatial-domain thermoreflectance technique (SDTR) previously reported for a comparison [8]. Additionally, measurements of several U3Si2 and UN phase regions of a polished UN/U3Si2 (70/30 vol.%) sample were taken, and the resulting calculated D values are reported, with both techniques showing excellent agreement between samples. This technique was used to scan a multiphase region at 5 micron increments to generate a local diffusivity map, demonstrating the utility of the techniques for measuring thermal transport properties in specimens with precipitates and secondary phases. Furthermore, the technique is currently being applied to measure thermal properties of Fast Flux Test Reactor (FFTR) irradiated metal fuel specimens whose porous microstructure make it very difficult to measure using other techniques. Comparison of the local scale measurements are compared with the pre-irradiated fuel samples to show the degradation of thermal transport in fuels due to pores from fission gas bubbles and other irradiation induced defects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Validation of ORIGEN for VVER-440 Spent Fuel with Application to Fork Detector Safeguards Measurements

The US Department of Energy National Nuclear Security Administration and the European Atomic Energy Community (Euratom) are collaborating with the Radiation and Nuclear Safety Authority in Finland to assess spent fuel verification methods for potential application to measurements at the planned spent fuel encapsulation plant and geological repository prior to final disposal in Finland. The fork detector (FDET) used to measure the neutron and gamma radiation from a given spent fuel assembly is an existing technology widely used by the International Atomic Energy Agency (IAEA) and Euratom for the safeguards verification of spent fuel operator declaration. Recently, an FDET data analysis software, referred to as the ORIGEN module, was developed and incorporated into the IAEA/Euratom Integrated Review and Analysis Program. This module uses the ORIGEN burnup code to calculate the nuclide concentrations and the neutron and gamma source terms in the spent fuel based on operator declarations. Then, to predict the expected FDET signals for a given fuel assembly, the module combines the source terms calculated by ORIGEN with FDET response functions that were pre-generated using MCNP models. The inspector can compare the calculated signals to the measured values in real time to identify possible anomalies in fuel assembly’s operator declaration, integrity, or measurement. In this work, the capability of the ORIGEN module was extended from application to typical light water reactor fuels to use for VVER-440 assembly types. The accuracy of ORIGEN for this type of fuel assembly calculations was assessed by comparing calculated nuclide concentrations against destructive assay measurements for VVER-440 spent fuel. The performance of the ORIGEN module for FDET safeguards verification in routine inspections was assessed using FDET measurement data for 13 spent VVER-440 assemblies that were measured at the Loviisa Nuclear Power Plant in Finland, by comparing the calculated signals to the measured quantities. The results show that the calculated FDET neutron and gamma detector signals are generally within 12% of the measurements except for one assembly. Thus, these results are applicable to future safeguards verification in the planned Finland encapsulation plant, such as for passive neutron albedo reactivity safeguards measurements.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2020

Coupling of Pronghorn and RELAP-7 for a Pebble Bed Reactor

High temperature gas cooled reactors (HTGR) are a candidate for timely Gen-IV reactor technology deployment because of high technology readiness and walk-away safety. Among HTGRs, pebble bed reactors (PBRs) have attractive features such as low excess reactivity and online refueling. Pebble bed reactors pose unique challenges to analysts and reactor designers such as continuous burnup distribution depending on pebble motion and recirculation, radiative heat transfer across a variety of gas-filled gaps, and long design basis transients such as pressurized and depressurized loss of forced circulation. Modeling and simulation is essential for both the PBR’s safety case and design process. In order to verify and validate the new generation codes the Nuclear Energy Agency (NEA) Data bank provide a set of benchmarks data together with solutions calculated by the participants using the state of the art codes of that time. An important milestone to test the new PBR simulation codes is the OECD NEA PBMR-400 benchmark which includes thermal hydraulic and neutron kinetic standalone exercises as well as coupled exercises and transients scenarios. In this work, the reactor multiphysics code MAMMOTH and the thermal hydraulics code Pronghorn, both developed by the Idaho National Laboratory (INL) within the multiphysics object-oriented simulation environment (MOOSE), have been used to solve Phase 1 exercises 1 and 2 of the PBMR-400 benchmark. The steady state results are in agreement with the other participants’ solutions demonstrating the adequacy of MAMMOTH and Pronghorn for simulating PBRs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Sensitivity and Uncertainty Quantification of Transition Scenario Simulations

This report documents the first collective attempt at developing and applying capabilities to quantify uncertainties, assess parametric sensitivities, and optimize multiple parameters and metrics in fuel cycle simulations generated by the SA&I Campaign. To do this, external codes that were designed to perform sensitivity analysis and uncertainty quantification (SA&UQ) needed to be coupled to the SA&I Campaign’s nuclear fuel cycle simulators (NFCS). In FY20, two approaches were pursued: 1) coupling Cyclus to an ORNL-internal code called MOT (Metaheuristic Optimization Tool) and 2) coupling DYMOND to the opensource SA&UQ tool kit Dakota. The primary objective of having these NFCS/SA&UQ coupled capabilities is to better inform DOE-NE and other stakeholders on the results generated from the NFCS. For a given set of fuel cycle strategies, policies, and technology assumptions that make up a fuel cycle scenario, these NFCS have traditionally been used by the SA&I Campaign to provide quantitative answers in terms of year-by-year mass flows, infrastructure requirements, costs, etc. With these newly developed coupled capabilities, the SA&I Campaign can now efficiently simulate hundreds or thousands of these scenarios, sample large ranges of parameters and assumptions, and use the unique features of the SA&UQ tools to process the data. This enables providing answers with known and propagated uncertainties, determining the sensitivity of important metrics to different parameters and assumptions, quantifying how much fuel cycle and technology parameters impact each other, and producing optimized fuel cycle strategies for single and multiple variables. To demonstrate these new capabilities, the Cyclus/MOT was used to model several scenarios ranging from simple fleet retirements to transitions to advanced reactors. Specifically, for a transition scenario from LWRs to SFRs and advanced LWRs, uncertainty quantification, sensitivity analysis, and optimization studies were applied to cases involving single and multiple parameter (input) and single and multiple metric (output) variations. In addition, a similar transition scenario was modeled to demonstrate how to optimize the reprocessing capacity parameter to minimize two performance metrics while taking into account uncertainties from two other parameters. Lastly, a depletion module based on SCALE/ORIGEN was added in Cyclus to simulate the third scenario that was designed to quantify the impact of the modeling assumption that all LWR used nuclear fuel have the same burnup. The newly developed DYMOND/Dakota capability was also applied to a transition scenario from the existing fleet to small modular reactors and fast reactors. This particular scenario involves not only explicit isotopic depletion via ORIGEN-2, but also includes multirecycling and utilizing the criticality search feature to determine the fresh fuel composition of recycled fuel, a feature unique to the DYMOND NFCS. A large database of simulations were run with 4 main parameters that were sampled: start date of reprocessing, reprocessing capacity, energy demand growth rate, and advanced reactor share of the fleet. The 4 main metrics were uranium consumption, enrichment requirements, waste generation, and levelized cost of electricity using data from the Cost Basis Report. The demonstrated SA&UQ results include those that inform on how to choose parameters to avoid “failed” scenarios, Sobol’ indices that inform on the importance of various parameters individually and synergistically, and Analysis of Variance (ANOVA) studies that decompose parameter ranges into groups and informs on whether variations are statistically significant.

Feng, B.↗
DOE OSTI2021

Analysis of PNAR Spent Fuel Safeguards Measurements using the ORIGEN Data Analysis Module

This paper summarizes the analysis of the Passive Neutron Albedo Reactivity (PNAR) measurements using the ORIGEN data analysis module for 23 boiling water reactor spent fuel assemblies that were performed in Finland under an international collaboration on spent fuel safeguards verification methods. PNAR is part of the proposed integrated nondestructive system to be used for safeguards verifications at the planned Finnish encapsulation facility. Besides measuring passive neutron and gamma emission rates from an assembly like a Fork detector, PNAR also measures the PNAR ratio, which is expected to correlate with the fissile content in the assembly. The emission rates and PNAR ratio can be used to verify the operator declarations and the fissile content of an assembly, respectively. The analysis was performed using the ORIGEN Data Analysis Module, which was originally developed for predicting Fork detector neutron and gamma signals for spent fuel measurements and has been integrated into the Integrated Review and Analysis Package developed by Euratom and the IAEA. The Module includes the ORIGEN burnup analysis code and integrates detector response functions pre-generated using MCNP to predict detector signals in several seconds per assembly. In this study, new response functions specific to PNAR measurements were generated for ORIGEN Module. The study also analyzes impacts of using detailed fuel design and operation information vs. standard safeguards information on results calculated by ORIGEN Module. Using detailed information reduced the standard deviation of relative differences between calculated and measured neutron count rates among the 23 assemblies from ~10% to ~4%. The results obtained using standard safeguards information for these PNAR measurements were similar to those obtained for the Fork detector. A clear trend was found between the calculated net neutron multiplications and the measured PNAR ratios of the 23 assemblies. This paper describes how ORIGEN Module calculates the expected PNAR neutron and gamma signals and PNAR ratio and how they compare with corresponding measured values.

Ilas, Germina↗
DOE OSTI2021

Fundamental Studies of Tritium Formation and Diffusivity in Pure and Defective Zircaloy-4 Getters

Zirconium (Zr) alloys have excellent mechanical properties at high temperature and are resistant to corrosion in different environmental conditions. These alloys are used as tritium (3H or T) getters in nuclear reactors due to their low absorption cross section to thermal neutrons and excellent thermo-mechanical properties. Zr alloys have better mechanical and thermal properties than many other refractory alloys including stainless steel. After the irradiation of TPBAR by neutron flux, 3H produced during irradiation diffuses though the pellets and is captured by the getter. 3H chemically reacts with Zr metal to form metal hydride (ZrTx). Hydrides thus formed are brittle and adversely affect the mechanical and thermal properties of alloys. The lattice mismatch at the interface of alloy and metal hydrides also creates a stress that significantly reduces the alloy’s performance and operation life. Therefore, understanding the behavior of 3H and its species becomes significant as fuel burnup is increased, which leads to increase in hydrogen pickup and oxide formation.

Duan, Yuhua↗
DOE OSTI2021

AGR-5/6/7 Irradiation Test Final As-run Report

This document presents the as-run analysis of the Advanced Gas Reactor (AGR) 5/6/7 irradiation experiment. AGR-5/6/7 is the last of a series of experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of the development and qualification of tri-structural isotropic (TRISO) low enriched fuel for use in high-temperature gas-cooled reactors (HTGR). The test train contained five separate capsules that were independently controlled and monitored. Each capsule contained multiple 24.91-mm-long and 12.25-mm-dimeter compacts filled with low-enriched uranium carbide/oxide tri-structural isotropic fuel particles. The objectives of the AGR 5/6/7 experiment were to: 1. Irradiate reference-design fuel particles to support fuel qualification. 2. Establish operating margins for the fuel, beyond normal operating conditions. 3. Provide irradiated-fuel performance data and irradiated-fuel samples for post irradiation examination and safety testing. The primary objective of the AGR-5/6 test (Capsules 1, 2, 4, and 5) was to verify the successful performance of the reference-design fuel under normal operating conditions. The AGR-7 test (Capsule 3) was designed to explore fuel performance at higher temperatures. Its primary objective is to demonstrate the capability of the fuel to withstand conditions beyond normal operating conditions, in support of plant design and licensing. AGR 5/6/7 will also provide irradiated-fuel performance data based on the fission gas release from particles during irradiation. To achieve the test objectives, the AGR-5/6/7 experiment was irradiated in the northeast (NE) flux trap of the ATR with a planned duration of 500 effective full-power days (EFPDs). The NE flux trap was selected because its larger diameter provided greater flexibility for test-train design compared to the Large B positions used for the AGR-1 and AGR-2 irradiations, significantly enhancing test capabilities for the combined irradiation campaigns. Due to delays in the ATR schedule, the AGR-5/6/7 irradiation was significantly shorter than the originally planned 13-cycle schedule. Irradiation began on February 16, 2018 and ended on July 22, 2020, spanning nine ATR cycles (162B?168A) over two and a half years. Thus, the AGR-5/6/7 fuel compacts were irradiated for a total of approximately 360.9 EFPDs. Final burnup values, on a per-compact basis, ranged from 5.66% to 15.26% fissions per initial heavy metal atom, while fast fluence values ranged from 1.62 to 5.55 × 1025 n/m2 (E >0.18 MeV). Time-averaged volume-averaged fuel temperatures on a capsule basis at the end of irradiation ranged from 756°C in Capsule 5 to 1313°C in Capsule 3 excluding days with significantly lower temperature during the two short powered axial locator mechanism cycles, 163A and 167A. By the end of irradiation, 48 out of 54 installed thermocouples (TC) had failed (the bottom three capsules lost all TCs). During the first five cycles (162B ? 165A), fission-gas isotope release-rate-to-birthrate (R/B) ratios were stable in the 10-8?10-6 range, and no in-pile particle failures were observed based on the gross gamma counts. During this time, the high exposed kernel fraction and high fuel particle temperatures in Capsule 1 led to the maximum R/B value of around 2 ? 10-6 for Kr-85m. The fission gas release in all capsules started to increase from the second half of Cycle 166A, when a large number of in-pile particle failures occurred in Capsule 1 and a gas line problem in this capsule caused fission gas leakage at various degrees into the other four capsules. This gas line problem also prevented fission gas release measurement for Capsule 1 during the last three cycles due to gas flow isolation. By the end of irradiation, it is estimated that approximately 15 particle failures in Capsule 3, which was considered possible at the start of the irradiation, since the experiment was designed to operate beyond the high-temperature gas-cooled reactor (HTGR) normal operating temperature range. A few hundred in-pile particle failures were estimated for Capsule 1 by the end of Cycle 166A, but the total number of failures is unknown due to lack of fission gas release data in the later cycles. Additionally, four potential in-pile failures were identified for Capsule 2 during the last cycle, 168A. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on absence of the typical spikes in gross gamma counts and low failure estimates using the AGR-3/4 R/B per exposed kernel model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Microstructural and Micro-Chemical Evolutions in the Irradiated UCO Fuel Kernels of AGR-1 and AGR-2 TRISO Fuel Particles

AGR-1 and AGR-2 TRISO fuel particles were fabricated with slightly different fuel kernel chemical compositions, modified fabrication processes, different fuel kernel diameters, and changed 235U enrichments. To correlate those differences with the fuel kernel responses to neutron irradiations in terms of irradiated fuel microstructure, fission products chemical and physical states, and fission gas bubble evolutions, extensive microstructural and analytical characterizations were conducted. The studies used a state of art transmission electron microscopy (TEM) equipped with Energy-dispersive X-ray spectroscopy (EDS) of four silicon solid-state detectors which have super sensitivity and fast speed. The TEM specimens were prepared from selected AGR-1 and AGR-2 irradiated fuel kernels exposed to safety testing after irradiation. The particles were chosen to represent a representative irradiation conditions with a fuel burnup within the range from 10.8 to 18.6% FIMA, and the time-average volume-average temperatures vary from 1070 to 1287°C. The 235U enrichment was 19.74 wt.% for the AGR1 fuel kernels and 14.03 wt.% for the AGR-2 fuel kernels. The TEM results show that there were significant microstructural reconstructions in the irradiated fuel kernels for both the AGR-1 and AGR-2 fuels. There are four major phases including fuel matrix of UO2 and UC, U2RuC2, and UMoC2 in the irradiated AGR2 fuel kernel. Zr and Nb form solid solution in the UC phase. UMoC2 phase often shows a detectable concentration of Tc. Pd was found to mainly locate in the buffer layer or to be associated with fission gas bubble within the UMoC2 phase. The EDS maps qualitatively show that the rare-earth fission products (Nb, et al.) preferentially reside in the UO2 phase. In contrast, in the irradiated AGR1 fuel kernel, no U2RuC2 or UMoC2 precipitates were positively identified. Instead, there is a high number of rod-shape precipitates enriched with Ru, Tc, Rh, and Pd observed in the fuel kernel center and edge zone. The difference of microstructural and micro-chemical evolutions in irradiated fuel kernels between the AGR-1 and AGR-2 TRISO fuel particle may result from a combined factor of irradiation temperature, fuel geometry and chemical composition. However, the irradiation temperature probably play a more deterministic role. Limited electron energy loss spectroscopy (EELS) characterizations on the AGR2 fuel kernel show that there is nearly no carbon in the UO2 phase while a small fraction of oxygen was detected in the UC/UMoC2 phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

AGR-5/6/7 Irradiation Results and Reporting

Final fuel qualification irradiation (AGR-5/6) and performance margin test (AGR-7) 425 µm diameter kernels with 15.5% 235U enrichment Target time-average peak fuel temperatures ~1500°C Target peak burnup 18% FIMA 194 UCO fuel compacts (~570,000 particles) in five capsules Irradiation started Feb 2018 in ATR Northeast Flux Trap

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Nuclear Material Control and Accountancy Approach for Pebble Fueled Reactors using a Novel Pebble-Type Identification and Classification Technology

In FY21, Argonne National Laboratory (ANL) with researchers at Texas A&M University (TAMU) designed and engineered a prototypical device for accounting types of irradiated pebbles (for example with different 235U enrichments or pure graphite) in Pebble-Fueled Reactors (PFRs). Through engagements with reactor designers, a need arose to assist in identifying and categorizing types of pebbles as a complementary nuclear material control method that would synergize with designers’ use of fuel burnup measurements for material accountancy needs. As part of an overall nuclear material control approach, a concept of pebble batch accounting was investigated using extrinsic non-radiological features to identify intrinsic characteristics. This concept of batch accounting led to the ability of identifying types of pebbles based on characteristics such as initial 235U enrichment of pebble batches or dates of introduction into the reactor core. Identification was achieved by embedding the 5-mm thick graphite periphery of pebbles with 2-mm diameter inert Yttria-Stabilized Zirconia (YSZ) microspheres to achieve an averaged volumetric density (i.e., common spacing between microspheres) unique to that type of pebble. With an ultrasound imaging system in proximity with each pebble, the YSZ microspheres in the pebble proved visible and their spacing became the unique feature upon which pebble type categorization could occur. At the culmination of FY21, ANL intended on delivering and installing the prototype at TAMU for initial testing but, due to the on-going pandemic, this was postponed until FY22.

Gariazzo, Claudio↗
DOE OSTI2021

Understanding TRISO Coated Particle Neutron Irradiation Behavior:Evolution of Advanced Micro Analysis and Electron Microscopy Approaches

Objectives and motivation• Provide data for fuel qualification in support of reactor licensing• Establish a domestic commercial TRISO fuel fabrication capability Approach • Focus is on developing and testing UCO TRISO fuel –Develop fuel fabrication and QC measurement methods, first at lab scale and then at industrial scale –Perform irradiation testingover a range of conditions (burnup, temperature, fast neutron fluence) –Perform post-irradiation examination and safety testingto demonstrate and understand performance during irradiation and during accident conditions –Develop fuel performance modelsto better predict fuel behavior –Perform fission product transport experiments to improve understanding and refine models of fission product transport

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Implementation of an Experimental Setup Based on the Three-Omega Method for Thermal Conductivity Measurements of Molten Salts

Molten salt reactors (MSRs) are one of the most promising next-generation nuclear reactor designs which use molten salts as the fuel and coolant. To design, model, predict, license, and operate MSRs, the behavior of the fuel and coolant must be understood as a function of temperature and irradiation, i.e., burnup. Of particular importance and complexity is the reliable and reproducible measurement of thermal conductivity of molten salts at high temperatures (> 500 °C). Thermal conductivity provides information on the rate at which heat passes through a specified material and is dependent on chemical composition. Currently, in the national laboratory complex, several methods for measuring thermal conductivity on molten salt systems are under development, however, to date, consistent data have not been produced. Typically, thermal conductivity measurements of high-temperature melts have been conducted by using the Transient Hot Wire (THW) method where thermal conductivity is determined by the change in temperature over time at a certain distance from a heating wire. Another time-dependent technique is the laser flash method, commonly used for solid samples. Laser flash requires prior measurements of density and heat capacity to calculate the thermal conductivity of the sample, introducing additional measurement errors. Steady state and time-dependent measurements such as THW and laser flash have errors from convection and ambient temperature fluctuations (heat radiation). In order to produce high fidelity thermal conductivity data, a measurement technique needs to be developed that will reduce the effect of convection at high temperatures by measuring in a very fast time window. In addition, to measure on actinide and irradiated salts the sample size should be small. Therefore, this project aims to develop a frequency-domain technique based on the three-omega (3?) method, previously proven to work on solids, nanofluids and low temperature solar salts (25 to 250 °C). If the 3?-device can be designed with materials that can withstand high temperatures (>500 °C) and can be configured to reduce errors due to convection, then it would prove to be a valuable technique for ensuring thermal conductivity on molten salt systems needed for MSR development. For this proposal, the 3? instrument will be designed, assembled, and tested on non-radioactive salts before being used on actinide bearing salts. In addition, a thermal model will be developed to determine the thermal conductivity of the sample from the measured thermal oscillation of the sensor. Because 3? is a direct method that requires a small volume of sample and works in a very fast time window, it will aid in suppressing the interference due to convection which is ideal when working with high temperature liquid samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Dynamic System Scaling Application to Accelerated Nuclear Fuel Testing

The development of nuclear fuel and materials requires a continuous effort to investigate the acute and prolonged effects of irradiation, thermal-material stress, chemical change, or other conceivable damage mechanics acquired during normal operation or accident scenarios throughout its lifetime. As in-core fuel property measurement techniques advance to support in the real-time, non-invasive, and enhanced accuracy realm, it is the future of fuel development to pursue to higher degrees of control, predictability of integral test behavior via separate effects test (SET), and shorter test time intervals. The fuel development life cycle from initial concept to commercial licensing is approximated to be 20 years and current literature suggests by optimizing fuel performance codes with SETs, the process could possibly be compressed to 5 to 10 years. Recently, a research group in the Idaho National Laboratory (INL) is testing reduced scale fuel rods and increased power density to accelerate evolution of fuel phenomena in metallic fuels. In support of nuclear fuel rod development, compressing fuel test process, and accelerating fuel phenomena, it was the purpose of this study to investigate nuclear fuel performance phenomena via literature review and effectively scale the initial conditions, boundary conditions, and geometric properties to describe the time-dependent response including to fuel burnup, thermal and mechanical stress, transmutations and inter-diffusion, and other relevant observed phenomena. The study was based on BISON simulations of historic EBR-II metallic fuel experiments and Dynamical System Scaling (DSS) method are utilized to assess effects of scaling activity including fuel phenomena acceleration and calculations of time-dependent distortions. The research successfully scaled metallic fuel phenomena, accelerated fuel testing, and assessed the distortions for each scaled case derived.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

The U.S. Accident Tolerant Fuels Program — Update on a National Initiative

In 2012 the U.S. Congress directed the Department of Energy’s (DOE) Office of Nuclear Energy to give priority to developing enhanced fuels and cladding for light water reactors to improve safety in the event of accidents in the reactor or spent fuel pools. DOE developed a plan with a goal to insert a Lead Test Assembly (LTA) into a commercial light water reactor by the end of FY 2022. Three of the leading commercial nuclear fuel vendors, in concert with several participating commercial nuclear utilities, are now seriously engaged in this initiative and have exceeded initial expectations by having met DOE’s goal this year, three years ahead of schedule. The early successes of the ATF program are due in part to a strong collaboration by the DOE national laboratories with both commercial nuclear fuel vendors and the U.S. Nuclear Regulatory Commission. This undertaking has recently been expanded to incorporate an effort to extend burnup from the current U.S. regulatory limit of 62 GWD/MTU and increase enrichment as necessary to support routine utilization of fuel at >75 GWD/MTU. This effort provides a critical economic incentive to accelerate the deployment of ATF technologies. This paper reviews the DOE-sponsored, industry-led ATF concepts currently under development and highlights the contributions made by the DOE laboratories in support of these ATF concepts, including: 1) steady-state irradiation testing in the Advanced Test Reactor (ATR) and High Flux Isotope Reactor (HFIR); 2) transient irradiation testing in the Transient Reactor Test Facility (TREAT); 3) fabrication process development and characterization of high density fuels, Cr-coated Zry cladding, FeCrAl cladding, and SiC cladding; and 4) post-irradiation examination of lead test rods irradiated in commercial reactors.

Goldner, Frank J.↗
DOE OSTI2022

Experiment Assembly and Testing in Hot Cell in Support of Advanced Fuels Irradiation Testing

Follow-on experimentation of irradiated nuclear fuel is critical to understanding fuel behavior at different stages of the fuel lifecycle. Transient experiments using fuel with high burnup can enlarge understanding of fuel fragmentation, relocation and dispersal under various reactor accident situations. Assembling experiments with such fuel requires remote operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Kernel Buffer Volume Fraction Margin of the AGR Designed Fuel Particle

Modeling results used to assess the fuel performance of the TRISO-coated fuel particles as a function of kernel/buffer volume fraction include SiC tangential stress, formation of the buffer/IPyC gap, particle temperature profile, internal particle pressure, fission gas released from the kernel, probability of fuel particle failure, and fission product diffusion. These results were evaluated at two burnup levels and irradiation temperatures to bound expected steady-state irradiation conditions. In general, increasing the kernel/buffer volume fraction increases the SiC stress and subsequently the failure probability of a fuel particle when compared to the AGR designed particle. There was little impact on the fission product diffusion through the particle as the kernel/buffer volume fraction increased.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Combined TREAT-LOC & SATS Integral LOCA Experiment Plan

The Transient Reactor Test Facility (TREAT) loss-of-coolant (LOC) and highburnup (HBu) experiment series, along with the Severe Accident Test Station (SATS) HBu experiment series, are integral LOC accident (LOCA) experiments planned under the Department of Energy (DOE) Advanced Fuels Campaign (AFC) program, which aims to support burnup extension needs by addressing identified R&D priorities in order to achieve an improved understanding of fuel fragmentation, relocation, and dispersal (FFRD) of HBu fuel during LOCA events. Priorities have been identified by the Electric Power Research Institute (EPRI)’s Collaborative Research on Advanced Fuel Technologies (CRAFT) Fuel Performance and Testing Technical Experts Group (FPTTEG). The data produced under this plan will be used to further validate and confirm existing models and inform future R&D and model development. The experimental program was specifically developed to address data gaps and opportunities identified via detailed review of the existing public knowledge base on LOCA FFRD, as well as reviewing specific experimental development activities regarding prototypic LOCA conditions for light-water reactor (LWR) systems. The test program relies on a unique combination of in- and out-of-pile experimental approaches to provide a clear tieback to the existing integral and semi-integral LOCA experiment database, using state-of-the-art facilities. More importantly, the program will systematically investigate the impacts of prototypic HBu fuel/cladding thermomechanical behaviors under postulated LWR LOCA conditions not yet fully investigated. These conditions correspond with prototypic decay-energy heatup (DEH) and stored-energy heatup (SEH) conditions. First, TREAT’s unique capability will enable the first evaluation of the impact of SEH conditions on HBu fuels. The test program will emphasize the development of an improved mechanistic understanding of key phenomena through independent experimental systems, development of a database to support fuel performance modeling tools, world-leading advanced materials characterization, and the most advanced approach to in situ diagnostics ever deployed to evaluate FFRD. The results will represent a significant leap forward in evaluating prototypic conditions and novel data to support modeling development and validation, as well as to inform the technical basis for LOCA-induced FFRD.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

BISON Capability, Validation and Demonstration for Reactivity-Initiated Accidents

Reactivity Initiated Accidents (RIA) are design basis accidents that could have adverse impacts on the core coolability. In the unlikely event that sufficient reactivity is inserted into the reactor core by the ejected/dropped control rod, prompt energy deposition into the fuel can occur, which when sufficiently high can lead to fuel rod failure or, at large energy deposition levels, expulsion of UO2 fragments or molten UO2 material from the fuel rod. This results in a release of fission product and fuel into the coolant and has the potential to compromise core coolability and threatening the pressure boundary of the primary coolant system. The design basis RIA is one of the industry challenging problems that the CASL aimed to address; the CASL RIA Challenge Problem Charter [1] states, ?The Pressurized Water Reactor (PWR) Rod Ejection Accident (REA) and Boiling Water Reactor (BWR) Control Rod Drop Accident (CRDA) are postulated accidents with consequences that are important to nuclear safety (fuel rod integrity and core coolability). Currently each reload core design must be analyzed to meet regulatory acceptance criteria. The goal of CASLs ModSim capability for RIA is to model the event at a higher fidelity, with validation to existing tests, to better model the transient neutronics and the progression of the fuel and cladding thermal-mechanical behavior. These improved analytical capabilities can be used to better inform reload core design, limits on fuel assembly discharge burnup, restrictions on placement of fuel in the reactor, control rod insertion limits, operating margin, and performance sensitivities.? In support of that charter, BISON, the fuel performance code has been used to demonstrate the simulation of thermal-mechanical behavior of LWR fuels during a reactivity-initiated accident. The combination of mechanical, thermal, and thermal-hydraulic phenomena all present during an RIA makes a multi-physics code such as BISON a valuable tool for modeling these scenarios. This paper will highlight many of the activities associated with BISON relevant to reactivity-initiated accident capability development and validation efforts. These efforts have been performed under both CASL and the Nuclear Energy Advanced Modeling and Simulation (NEAMS) programs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗