Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

Computation of External Aerodynamics for a Canard Rotor/Wing Aircraft

The aerodynamic loads on a Canard Rotor/Wing vehicle are investigated using inviscid numerical simulations to understand the aerodynamic characteristics of the vehicle during conversion from rotorcraft to fixed wing flight. Steady numerical simulations at five azimuthal rotor indices are presented over a quarter turn of the rotor, producing 19 points during a single rotation due to symmetry. A Cartesian mesh approach is used to compute the steady flow field. All computations are done with a faired over engine inlet and exit to be consistent with the wind tunnel model geometry. Modification to the geometry is suggested and the aerodynamic effect of the modification is discussed.

Pandya, S.↗

Active Control of Aerodynamic Noise Sources

Aerodynamic noise sources become important when propulsion noise is relatively low, as during aircraft landing. Under these conditions, aerodynamic noise from high-lift systems can be significant. The research program and accomplishments described here are directed toward reduction of this aerodynamic noise. Progress toward this objective include correction of flow quality in the Low Turbulence Water Channel flow facility, development of a test model and traversing mechanism, and improvement of the data acquisition and flow visualization capabilities in the Aero. & Fluid Dynamics Laboratory. These developments are described in this report.

Reynolds, Gregory A.↗

System Identification of a Vortex Lattice Aerodynamic Model

The state-space presentation of an aerodynamic vortex model is considered from a classical and system identification perspective. Using an aerodynamic vortex model as a numerical simulator of a wing tunnel experiment, both full state and limited state data or measurements are considered. Two possible approaches for system identification are presented and modal controllability and observability are also considered. The theory then is applied to the system identification of a flow over an aerodynamic delta wing and typical results are presented.

Juang, Jer-Nan↗

Blocked Grid Technologies as Applied to Aerodynamic Configurations

The advantages and disadvantages of the blocked grid methodology are discussed using results from ENSAERO, CNS, and CNS-FV. The first two codes are based on finite differences and the last on cell-centered finite volume formulation. Techniques that enhance the utility of the blocked (or patched) grid methodology are described. These techniques include mesh discontinuous zonal interfaces, sliding zonal interfaces, fast search procedures, and virtual zones. All of these methods are designed with two goals; namely extend the use of patched grids to unsteady aerodynamics, e.g. oscillating control flaps, and provide the user more flexibility in the grid topologies available for gridding complex aerodynamic configurations. For example, the use of virtual zones allows the user the choice of using one grid topology for surface grids, and another for the volume grids. This additional flexibility has a large impact in the amount of calendar time required to block and grid a complex aerodynamic configuration. Several examples are shown demonstrating the new features. Other issues involving grid generation are also discussed. In particular the existing problems of defining grid quality measures which are relevant are also described.

Klopfer, Goetz↗

Aerodynamic Performance of Scale-Model Turbofan Outlet Guide Vanes Designed for Low Noise

The design of effective new technologies to reduce aircraft propulsion noise is dependent on an understanding of the noise sources and noise generation mechanisms in the modern turbofan engine. In order to more fully understand the physics of noise in a turbofan engine, a comprehensive aeroacoustic wind tunnel test programs was conducted called the 'Source Diagnostic Test.' The text was cooperative effort between NASA and General Electric Aircraft Engines, as part of the NASA Advanced Subsonic Technology Noise Reduction Program. A 1/5-scale model simulator representing the bypass stage of a current technology high bypass ratio turbofan engine was used in the test. The test article consisted of the bypass fan and outlet guide vanes in a flight-type nacelle. The fan used was a medium pressure ratio design with 22 individual, wide chord blades. Three outlet guide vane design configurations were investigated, representing a 54-vane radial Baseline configuration, a 26-vane radial, wide chord Low Count configuration and a 26-vane, wide chord Low Noise configuration with 30 deg of aft sweep. The test was conducted in the NASA Glenn Research Center 9 by 15-Foot Low Speed Wind Tunnel at velocities simulating the takeoff and approach phases of the aircraft flight envelope. The Source Diagnostic Test had several acoustic and aerodynamic technical objectives: (1) establish the performance of a scale model fan selected to represent the current technology turbofan product; (2) assess the performance of the fan stage with each of the three distinct outlet guide vane designs; (3) determine the effect of the outlet guide vane configuration on the fan baseline performance; and (4) conduct detailed flowfield diagnostic surveys, both acoustic and aerodynamic, to characterize and understand the noise generation mechanisms in a turbofan engine. This paper addresses the fan and stage aerodynamic performance results from the Source Diagnostic Test.

Hughes, Christopher E.↗

Prediction of Aerodynamic Coefficients using Neural Networks for Sparse Data

Basic aerodynamic coefficients are modeled as functions of angles of attack and sideslip with vehicle lateral symmetry and compressibility effects. Most of the aerodynamic parameters can be well-fitted using polynomial functions. In this paper a fast, reliable way of predicting aerodynamic coefficients is produced using a neural network. The training data for the neural network is derived from wind tunnel test and numerical simulations. The coefficients of lift, drag, pitching moment are expressed as a function of alpha (angle of attack) and Mach number. The results produced from preliminary neural network analysis are very good.

Rajkumar, T.↗

Improving the Unsteady Aerodynamic Performance of Transonic Turbines using Neural Networks

A recently developed neural net-based aerodynamic design procedure is used in the redesign of a transonic turbine stage to improve its unsteady aerodynamic performance. The redesign procedure used incorporates the advantages of both traditional response surface methodology and neural networks by employing a strategy called parameter-based partitioning of the design space. Starting from the reference design, a sequence of response surfaces based on both neural networks and polynomial fits are constructed to traverse the design space in search of an optimal solution that exhibits improved unsteady performance. The procedure combines the power of neural networks and the economy of low-order polynomials (in terms of number of simulations required and network training requirements). A time-accurate, two-dimensional, Navier-Stokes solver is used to evaluate the various intermediate designs and provide inputs to the optimization procedure. The procedure yielded a modified design that improves the aerodynamic performance through small changes to the reference design geometry. These results demonstrate the capabilities of the neural net-based design procedure, and also show the advantages of including high-fidelity unsteady simulations that capture the relevant flow physics in the design optimization process.

Rai, Man Mohan↗

Status of Nozzle Aerodynamic Technology at MSFC

This viewgraph presentation provides information on the status of nozzle aerodynamic technology at MSFC (Marshall Space Flight Center). The objectives of this presentation were to provide insight into MSFC in-house nozzle aerodynamic technology, design, analysis, and testing. Under CDDF (Center Director's Discretionary Fund), 'Altitude Compensating Nozzle Technology', are the following tasks: Development of in-house ACN (Altitude Compensating Nozzle) aerodynamic design capability; Building in-house experience for all aspects of ACN via End-to-End Nozzle Test Program; Obtaining Experimental Data for Annular Aerospike: Thrust eta, TVC (thrust vector control) capability and surface pressures. To support selection/optimization of future Launch Vehicle propulsion we needed a parametric design and performance tool for ACN. We chose to start with the ACN Aerospike Nozzles.

Ruf, Joseph H.↗

Aerodynamic Drag and Drag Reduction: Energy and Energy Savings (Invited)

An assessment of the role of fluid dynamic resistance and/or aerodynamic drag and the relationship to energy use in the United States is presented. Existing data indicates that up to 25% of the total energy consumed in the United States is used to overcome aerodynamic drag, 27% of the total energy used in the United States is consumed by transportation systems, and 60% of the transportation energy or 16% of the total energy consumed in the United States is used to overcome aerodynamic drag in transportation systems. Drag reduction goals of 50% are proposed and discussed which if realized would produce a 7.85% total energy savings. This energy savings correlates to a yearly cost savings in the $30Billion dollar range.

Wood, Richard M.↗

Preliminary Investigation of Stagnation Point Liquid Injection Influence on Blunt Body Aerodynamics

A preliminary investigation has been performed to determine the influence of stagnation point water injection on the hypersonic aerodynamic forces and moments for two-dimensional blunt bodies. This investigation was performed in the Langley 20-Inch Mach 6 Air Tunnel, and represents the qualitative first phase of a study to examine the potential benefits of water injection to reduce aerodynamic drag and aero-heating. Tests with a 4-inch diameter hemisphere cylinder and a 4-inch diameter cylinder with a span 1.5 times the diameter were performed over a range of free-stream unit Reynolds number from two million to six million per ft and of angle of attack (-5 deg to 5 deg) with water and gaseous nitrogen injection at the geometric stagnation point. The momentum flux ratio, that is, the ratio of the momentum flux of the jet to that of the free-stream flow, was varied from the non-blowing value of zero up to 0.00031 by maintaining the jet momentum fixed and varying the free-stream momentum, hence Reynolds number. The effect of water injection on the aerodynamic drag coefficient for the hemisphere cylinder was observed to be negligible as the momentum flux ratio was increased to 0.00017, but decreased significantly as this ratio increased above 0.00017; a nearly 50 percent reduction in drag occurred for a factor of two increase in momentum flux ratio.

Woods, William C.↗

Aerodynamic Design Opportunities for Future Supersonic Aircraft

A discussion of a diverse set of aerodynamic opportunities to improve the aerodynamic performance of future supersonic aircraft has been presented and discussed. These ideas are offered to the community in a hope that future supersonic vehicle development activities will not be hindered by past efforts. A number of nonlinear flow based drag reduction technologies are presented and discussed. The subject technologies are related to the areas of interference flows, vehicle concepts, vortex flows, wing design, advanced control effectors, and planform design. The authors also discussed the importance of improving the aerodynamic design environment to allow creativity and knowledge greater influence. A review of all of the data presented show that pressure drag reductions on the order of 50 to 60 counts are achievable, compared to a conventional supersonic cruise vehicle, with the application of several of the discussed technologies. These drag reductions would correlate to a 30 to 40% increase in cruise L/D (lift-to-drag ratio) for a commercial supersonic transport.

Wood, Richard M.↗

Training Data Requirement for a Neural Network to Predict Aerodynamic Coefficients

Basic aerodynamic coefficients are modeled as functions of angle of attack, speed brake deflection angle, Mach number, and side slip angle. Most of the aerodynamic parameters can be well-fitted using polynomial functions. We previously demonstrated that a neural network is a fast, reliable way of predicting aerodynamic coefficients. We encountered few under fitted and/or over fitted results during prediction. The training data for the neural network are derived from wind tunnel test measurements and numerical simulations. The basic questions that arise are: how many training data points are required to produce an efficient neural network prediction, and which type of transfer functions should be used between the input-hidden layer and hidden-output layer. In this paper, a comparative study of the efficiency of neural network prediction based on different transfer functions and training dataset sizes is presented. The results of the neural network prediction reflect the sensitivity of the architecture, transfer functions, and training dataset size.

Korsmeyer, David↗

Aerodynamic Drag and Drag Reduction: Energy and Energy Savings (Invited)

An assessment of the role of fluid dynamic resistance and/or aerodynamic drag and the relationship to energy use in the United States is presented. Existing data indicates that up to 25% of the total energy consumed in the United States is used to overcome aerodynamic drag, 27% of the total energy used in the United States is consumed by transportation systems, and 60% of the transportation energy or 16% of the total energy consumed in the United States is used to overcome aerodynamic drag in transportation systems. Drag reduction goals of 50% are proposed and discussed which if realized would produce a 7.85% total energy savings. This energy savings correlates to a yearly cost savings in the $30Billion dollar range.

Wood, Richard M.↗

Estimation of Unsteady Aerodynamic Models from Flight Test Data

This report summarizes the activities in aerodynamic model estimation from flight data. In addition to public presentations at the AIAA Atmospheric Flight Mechanics Conferences, two presentations at Boeing-Seattle were made during personal trips. These are discussed in the following: 1. Methodology of Aerodynamic Model Estimation from Flight Data. 2. Applications of F-16XL aerodynamic modeling. 3. Modeling of turbulence response. 5. Presentations at Boeing-Seattle. 6. Recommendations. and 7. References.

Lan, C. Edward↗

An Aerodynamic Analysis of a Spinning Missile with Dithering Canards

A generic spinning missile with dithering canards is used to demonstrate the utility of an overset structured grid approach for simulating the aerodynamics of rolling airframe missile systems. The approach is used to generate a modest aerodynamic database for the generic missile. The database is populated with solutions to the Euler and Navier-Stokes equations. It is used to evaluate grid resolution requirements for accurate prediction of instantaneous missile loads and the relative aerodynamic significance of angle-of-attack, canard pitching sequence, viscous effects, and roll-rate effects. A novel analytical method for inter- and extrapolation of database results is also given.

Meakin, Robert L.↗

Prediction of Aerodynamic Coefficients for Wind Tunnel Data using a Genetic Algorithm Optimized Neural Network

A fast, reliable way of predicting aerodynamic coefficients is produced using a neural network optimized by a genetic algorithm. Basic aerodynamic coefficients (e.g. lift, drag, pitching moment) are modelled as functions of angle of attack and Mach number. The neural network is first trained on a relatively rich set of data from wind tunnel tests of numerical simulations to learn an overall model. Most of the aerodynamic parameters can be well-fitted using polynomial functions. A new set of data, which can be relatively sparse, is then supplied to the network to produce a new model consistent with the previous model and the new data. Because the new model interpolates realistically between the sparse test data points, it is suitable for use in piloted simulations. The genetic algorithm is used to choose a neural network architecture to give best results, avoiding over-and under-fitting of the test data.

Rajkumar, T.↗

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on an Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails: Tabulated Data for the Model with Twin Vertical Tails - Supplement 2

Tabulated results of a wind-tunnel investigation of the aerodynamic loads on a canard airplane model with twin vertical tails are presented for Mach numbers from 0.70 to 2.22. The Reynolds number for the measurements was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. The results include local static-pressure coefficients measured on the wing, body, and one of the vertical tails for angles of attack from -4 degrees to 16 degree angles of sideslip of 0 degrees and 5.3 degrees, and nominal canard deflections of O degrees and 10 degrees. Also included are section force and moment coefficients obtained from integrations of the local pressures and model-component force and moment coefficients obtained from integrations of the section coefficients. Geometric details of the model are shown and the locations of the pressure orifices are shown. An index to the data contained herein is presented and definitions of nomenclature are given. Detailed descriptions of the model and experiments and a brief discussion of some of the results are given. Tabulated results of measurements of the aerodynamic loads on the same canard model but having a single vertical tail instead of twin vertical tails are presented.

Peterson, Victor L.↗

Reduced-Order Models Based on Linear and Nonlinear Aerodynamic Impulse Responses

This paper discusses a method for the identification and application of reduced-order models based on linear and nonlinear aerodynamic impulse responses. The Volterra theory of nonlinear systems and an appropriate kernel identification technique are described. Insight into the nature of kernels is provided by applying the method to the nonlinear Riccati equation in a non-aerodynamic application. The method is then applied to a nonlinear aerodynamic model of RAE 2822 supercritical airfoil undergoing plunge motions using the CFL3D Navier-Stokes flow solver with the Spalart-Allmaras turbulence model. Results demonstrate the computational efficiency of the technique.

Silva, Walter A.↗