Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Vertical profiles of condensation nuclei

Condensation nuclei measurements using a low supersaturation (about 10%) thermal gradient diffusion cloud chamber (TGDCC) and a high supersaturation (about 200%) expansion type instrument were compared on a series of three balloon flights over Laramie, Wyoming. In general, the two instruments produced similar vertical profiles but some discrepancies remain unexplained. Agreement between the two would indicate that the low supersaturations used in the TGDCC were still large enough to cause the instrument to count essentially all of the particles present. The TGDCC condensation nuclei (CN) counter was flown at several sites in both the Northern and Southern Hemispheres. The results indicate the existence of a relative maximum in the CN mixing ratio associated with the upper equatorial troposphere and what appears to be a worldwide constant mixing ratio of CN above 20-25 km.

Rosen, J. M.↗
NASA NTRS1981

Contribution to CCN Workshop report from University of Wyoming group

The group's CCN counter is described. It is a static, horizontal, parallel plate thermal gradient diffusion chamber. Examples of the application of the CCN are presented and include the CCN spectra measured during the winter of 1978-79 near Elk Mountain, Wyoming. Comparisons of droplet concentrations derived from upwind CCN spectra are covered.

Rogers, D. C.↗
NASA NTRS1981

Description and discussion of the NRL TGDCC

The NRL thermal gradient diffusion cloud chamber (TGDCC) consists of two plates 7.5 cm in diameter separated by 1.25 cm and covered with saturated filter paper. The cylindrical wall separating the plates is glass. The top plate is at room temperature and the bottom plate is cooled with a thermoelectric cooler. The temperature difference is measured with several sets of thermocouples. The CCN concentration was determined from the video recording. This procedure of averaging the maximum count obtained on several successive recordings at the same supersaturation results in concentrations which are somewhat higher than concentrations calculated from an average across the plateau.

Hoppel, W. A.↗
NASA NTRS1981

An airborne isothermal haze chamber

Thermal gradient diffusion cloud chambers (TGDCC) are used to determine the concentrations of cloud condensation nuclei (CCN) with critical supersaturations greater than or equal to about 0.2%. The CCN concentrations measured with the airborne IHC were lower than theoretically predicted by factors ranging between 7.9 and 9.0. The CCN concentrations measured with the airborne IHC were lower than the concentrations measured with the larger laboratory IHC's by factors ranging between 3.9 and 7.5. The bounds of the supersaturation ranges of the airborne IHC and the CSU-Mee TGDCC do not overlap. Nevertheless, the slopes of the interpolated data between the bounds agree favorably with the theoretical slopes.

Hindman, E. E.↗
NASA NTRS1981

A description of the UK Meteorological Office CCN counter

The chamber is a thermal gradient diffusion type with the upper plate at room temperature and the lower plate thermoelectrically cooled. The light from a 25W projector bulb is focused in a beam of approximations 1x3 mm in the central part of the chamber. The light scattered by drops is viewed in the forward direction (40 deg) by a microscope and a sensitive photodetector. Experiments were performed to relate the peak output from the photocell with the maximum number of drops in the beam recorded photographically. The microscope is used to check the calibration at low concentrations of CCN. The results of the experiments and the performance of the counter are reported.

Kitchen, M.↗
NASA NTRS1983

Iron-copper metallization for flexible solar/cell arrays

The feasibility of a copper-base metallization for shallow-junction cells applied in flexible solar arrays in space is discussed. This type of metallization will reduce usage of precious metals (such as silver), increase case of bonding (by welding or by soldering) and eliminate heavy high Z interconnects (such as molybdenum). The main points of concern are stability against thermally induced diffusion of copper into silicon which causes degradation of shallow cell junctions, and low series resistance of the contact with semiconductor which promotes cell efficiency.

Lavendel, H. W.↗
NASA NTRS1984

Coordination of Fe, Ga and Ge in high pressure glasses by Moessbauer, Raman and X-ray absorption spectroscopy, and geological implications

For some time, it has been recognized that the structure of silicate liquids has a great bearing on such magma properties as viscosity, diffusivity, and thermal expansion and on the extrapolation of thermodynamic quantities outside of the experimentally measurable range. In this connection it is vital to know if pressure imposes changes in melt structure similar to the pressure-induced reconstructive transformations in crystals. In the present study on 1 bar and high pressure glasses, an investigation is conducted regarding the coordination of Fe(3+) in Fe silicate glasses by Moessbauer spectroscopy. Raman spectroscopy is employed to explore the coordinations of Ge(4+) in GeO2 glasses and of Ga(3+) in NaGa silicate glasses, while the coordination of Ga(3+) in NaGaSiO4 glasses is studied with the aid of methods of X-ray absorption spectroscopy.

Fleet, M. E.↗
NASA NTRS1985

Measurement of the nighttime infrared luminosity of Spacelab 1 in the H- and K-bands

Infrared measurements of the Spacelab 1, Space Transportation System 9, were made from the Maui Optical Station tracking facility using a sensitive photometer n two infrared bands, the H-band centered at a wavelength of 1.6 microns and the K-band centered at 2.3 micrometers. The objective was to measure radiation from the vicinity of the Shuttle arising from interaction of Shuttle surfaces with atmospheric particles. It was necessary to include the Shuttle itself in the field of view of the photometer. The integrated brightness of the entire Shuttle at a distance of 400 km was found to be equivalent to that of a star of magnitude +6.6 or 1.6 microns; it was much fainter in the visible. Most of the emission at 1.6 microns appears to be attributable to the Shuttle glow phenomenon. It is hundreds of times brighter than the zodiacal background. The radiation at 2.3 microns can be accounted for primarily by diffusely scattered thermal radiation from Earth's surface.

Witteborn, F. C.↗
NASA NTRS1986

Thermophoretically augmented mass transfer rates to solid walls across laminar boundary layers

Predictions of mass transfer (heavy vapor and small particle deposition) rates to solid walls, including the effects of thermal (Soret) diffusion ('thermophoresis' for small particles), are made by numerically solving the two-dimensional self-similar forced convection laminar boundary-layer equations with variable properties, covering the particle size range from vapor molecules up to the size threshold for inertial (dynamical nonequilibrium) effects. The effect of thermophoresis is predicted to be particularly important for submicron particle deposition on highly cooled solid surfaces, with corresponding enhancement factors at atmospheric conditions being over a thousand-fold at T(w)/T(e) equal to about 0.6. As a consequence of this mass transfer mechanism, the particle size dependence of the mass transfer coefficient to a cooled wall will be much weaker than for the corresponding case of isothermal capture by Brownian-convective diffusion.

Gokoglu, S. A.↗
NASA NTRS1986

Injection of dust into the Martian atmosphere - Evidence from the Viking Gas Exchange experiment

The hypothesis that predawn midlatitude storms are triggered by a soil humidification process is examined. A freeze/thaw model of the process is evaluated in the Viking Gas Exchange experiments conducted on Mars. The humidification-driven desorption and desiccation state of Martian soil samples are analyzed. The periodic humidification of equatorial regolith soil is studied in terms of pore space pressure during desorption events and soil diffusivity; the thermal properties of the regolith surface layer are modeled using the program of Clifford (1984). Consideration is given to the diurnal and seasonal cycles of the humidification process, the permanent, low-albedo features in the midlatitudes, and the production of H2SO4 and HCl aerosols.

Huguenin, R. L.↗
NASA NTRS1987

Transport properties of ions

The strong long-range interactions between (among) charged species require the inclusion of higher order contributions to the transport properties (viscosity, thermal conductivity, diffusion) of ionized gases than are required for neutral gases. These higher order contributions have been rewritten so that they are given in terms of universal functions which can be tabulated. Tables which provide for the rapid calculation of some higher order contributions to the transport properties of both ions and electrons are given. Some results which are useful for calculating the higher order contributions to the transport properties of mixtures of ions are also given. These results are applied to the ionic species in air at high temperatures.

Biolsi, Louis↗
NASA NTRS1988

Muon motion in titanium hydride

Motional narrowing of the transverse-field muon spin rotation signal was observed in gamma-TiH(x) for x = 1.83, 1.97, and 1.99. An analysis of the data for TiH1.99 near room temperature indicates that the mechanism responsible for the motion of the muon out of the octahedral site is thermally activated diffusion with an attempt frequency comparable to the optical vibrations of the lattice. Monte Carlo calculations to simulate the effect of muon and proton motion upon the muon field-correlation time were used to interpret the motional narrowing in TiH1.97 near 500 K. The interpretation is dependent upon whether the Bloembergen, Purcell, and Pound (BPP) theory or an independent spin-pair relaxation model is used to obtain the vacancy jump rate from proton NMR T1 measurements. Use of BPP theory shows that the field-correction time can be obtained if the rate of motion of the muon with respect to the rate of the motion for the protons is decreased. An independent spin-pair relaxation model indicates that the field-correlation time can be obtained if the rate of motion for the nearest-neighbor protons is decreased.

Kempton, J. R.↗
NASA NTRS1988

Vapor concentration measurement with photothermal deflectometry

Theoretical and experimental results for using the photothermal deflection technique to measure vapor species concentration, while minimizing the disturbance of the transport (material) parameters due to vapor heating, are developed and described. In contrast to common practice, the above constraints require using a pump-beam duty cycle of less than 50 percent. The theoretical description of the shortened heating time is based on a step-function formulation of the pumping cycle. The results are obtained as closed-form solutions of the energy equation for many chopping cycles until steady state is reached, by use of a Green's-function method. The Euler formulation of the Fermat principle is used to calculate the deflection angle. The equations are expanded to include the effects of vapor velocity on both the temperature and temperature gradient profiles. The effects of finite (unfocused) pump and probe beams and thermal (Soret) diffusion are also accounted for. Excellent agreement between theory and experiment is obtained.

Banish, R. Michael↗
NASA NTRS1989

A slow positron beam generator for lifetime studies

A slow positron beam generator using well-annealed polycrystalline tungsten moderators and a Na-22 positron source was developed. A 250 micro c source, deposited on a 2.54 micron thick aluminized mylar, is sandwiched between two (2.54 cm x 2.54 cm x 0.0127 cm) tungsten pieces. Two (2.54 cm x 2.54 cm x t cm) test polymer films insulate the two tungsten moderator pieces from the aluminized mylar source holder (t=0.00127 to 0.0127). A potential difference of 10 to 100 volts--depending on the test polymer film thickness (t)--is applied between the tungsten pieces and the source foil. Thermalized positrons diffusing out of the moderator pieces are attracted to the source foil held at an appropriate potential below the moderator pieces. These positrons have to pass through the test polymer films before they can reach the source foil. The potential difference between the moderator pieces and the aluminized mylar is so adjusted as to force the positrons to stop in the test polymer films. Thus the new generator becomes an effective source of positrons for assaying thin polymer films for their molecular morphology.

Singh, Jag J.↗
NASA NTRS1988

On the two-dimensional modelling of horizontal CVD reactors and its limitations

In order to clarify under what conditions two-dimensional theoretical models can realistically account for the actual growth rate distribution in horizontal CVD reactors, a systematic numerical study was performed, and the results were compared with published experimental data for the MOCVD of gallium arsenide. Three models of increasing complexity were studied. It is shown that two-dimensional models can produce realistic predictions only for reactors with large width-to-height (aspect) ratios, that are operated at subcritical Rayleigh number,i.e., under dominant forced flow conditions. But even then, depending on the carrier gas, thermal (Soret) diffusion must be included in the model. Furthermore, velocity corrections for finite aspect ratios must be made, and buoyancy effects can be significant in the entrance region. On the other hand, the results are relatively insensitive to axial diffusion, temperature dependence of transport properties (versus averaged properties), and an assumed Poiseuille velocity profile (versus a rigorous solution of the velocity field). Yet, boundary layer approximations are prone to give unrealistic results at the low Reynolds numbers typical for CVD operations.

Ouazzani, Jalil↗
NASA NTRS1992

Results of examination of silvered Teflon from the Long Duration Exposure Facility

A significant effort to determine the effects of low earth orbit (LEO) exposure on silver backed fluorinated ethylene-propylene (FEP) blankets from the Long Duration Exposure Facility (LDEF) was performed, and the results of this investigation are described. Extensive measurements of surface, optical, chemical, and mechanical properties were conducted. Effects of contamination and erosion rates of the FEP layer were determined. Specific results are reported on solar absorptance, thermal emittance, diffuse reflectance, cross sectional microphotography, secondary ion mass spectroscopy, electron scattering for chemical analysis, scanning electron microscopy, percent elongation, and tensile strength. These measurements show the effects of two distinctly different exposure environments, solar exposure, and simultaneous atomic oxygen (AO) and solar exposure.

Rousslang, Ken↗
NASA NTRS1992

Mass spectrometer use in a large chamber

The early satellites were somewhat insensitive to contamination produced during the construction and testing phases. The On-Orbit lifetime was such that contamination effects went either unnoticed or unrecognized. With today's On-Orbit lifetimes approaching 10+ years, contamination has become a paramount concern. The scientific payloads have increased in complexity and sensitivity. The ability to clean a contaminated sensor has greatly diminished. This requires better pumping systems and methods for improved monitoring. The conversion from diffusion pumped thermal vacuum chambers to cryo pumped chambers with the use of Misner traps and selective cold traps has reduced contamination. Witness samples supply a record of the condensates that remain after a testing cycle, but impart no knowledge of the contaminant migration during the cycle that may be a month in duration. Due to a customer's request that mass spectrometry be used during the testing of their spacecraft, a consultant was contracted to install a mass spectrometer to determine the feasibility of the instrument. The equipment and methodology described will start with the original system and its evolution to GE's present system.

Chuvala, Tom↗
NASA NTRS1993

Design, analysis, and fabrication of oxide-coated iridium/rhenium combustion chambers

Iridium-coated rhenium (Ir/Re) combustion chambers provide high temperature, oxidation-resistant operation for radiation-cooled liquid-fueled rocket engines. A 22-N (5-lb(sub f)) chamber has been operated for 15 hours at 2200 C (4000 F) using nitrogen tetroxide/monomethyl hydrazine (NTO/MMH) propellant, with negligible internal erosion. The oxidation resistance of these chambers could be further increased by the addition of refractory oxide coatings, providing longer life and/or operation in more oxidizing and higher temperature environments. The oxide coatings would serve as a thermal and diffusion barrier for the iridium coating, lowering the temperature of the iridium layer while also preventing the ingress of oxygen and egress of iridium oxides. This would serve to slow the failure mechanisms of Ir/Re chambers, namely the diffusion of rhenium to the inner surface and the oxidation of iridium. Such protection could extend chamber lifetimes by tens or perhaps hundreds of hours, and allow chamber operation on stoichiometric or higher mixture ratio oxygen/hydrogen (O2/H2) propellant. Extensive thermomechanical, thermochemical, and mass transport modeling was performed as a key material/structure design tool. Based on the results of these analyses, several 22-N oxide-coated Ir/Re chambers were fabricated and delivered to NASA Lewis Research Center for hot-fire testing.

Jang, Q.↗