Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Interpretation of the surface brightness of Phobos

Analysis of disk resolved images of Phobos obtained by the Phobos 2 spacecraft makes it possible to study the surface scattering law and albedo variations. Low phase angle images reveal variations in local geometric albedo about 10 percent, with a correlation length of about 1 km. The scattering law is reasonably well matched by the recently proposed LPI (Lumme et al., 1990) model, which makes it possible to deduce a small scale (1 mm) surface roughness (0.5), defined here as the rms tangent of the local surface normal relative to the mean surface normal in the Duxbury (1991) model of Phobos. This value is very close to what has been found for Mercury and the moon.

Peltoniemi, Jouni I.↗
NASA NTRS1991

Free convection in the Martian atmosphere

Researchers investigated the free convective regime for the Martian atmospheric boundary layer (ABL). Researchers generalized Schumann's model describing horizontal fluctuations and mean vertical gradients occurring during free convection to include convection driven by water vapor gradients and to include the effects of circulation above both aerodynamically smooth and rough surfaces. Applying the model to Mars, researchers found that nearly all the resistance to sensible and latent heat transfer in the ABL occurs within the thin interfacial sublayer at the surface. Free convection is found to readily occur at low pressures and high temperatures when surface ice is present. At 7 mb, the ABL should freely convect whenever the mean windspeed at the top of the surface layer drops below about 2.5 m s(-1) and surface temperatures exceed 250 K. Mean horizontal fluctuations within the surface layer are found to be as high as 3 m (-1) for windspeed, 0.5 K for temperature, and 10 (-4) kg m (-3) for water vapor density. Airflow over surfaces similar to the Antarctic Polar Plateau was found to be aerodynamically smooth on Mars during free convection for all pressures between 6 and 1000 mb, while surfaces with z sub o approx. equals 1 cm are aerodynamically rough over this pressure range.

Clow, G. D.↗
NASA NTRS1997

Electric Arc and Electrochemical Surface Texturing Technologies

Surface texturing of conductive materials can readily be accomplished by means of a moving electric arc which produces a plasma from the environmental gases as well as from the vaporized substrate and arc electrode materials. As the arc is forced to move across the substrate surface, a condensate from the plasma re-deposits an extremely rough surface which is intimately mixed and attached to the substrate material. The arc textured surfaces produce greatly enhanced thermal emittance and hold potential for use as high temperature radiator surfaces in space, as well as in systems which use radiative heat dissipation such as computer assisted tomography (CAT) scan systems. Electrochemical texturing of titanium alloys can be accomplished by using sodium chloride solutions along with ultrasonic agitation to produce a random distribution of craters on the surface. The crater size and density can be controlled to produce surface craters appropriately sized for direct bone in-growth of orthopaedic implants. Electric arc texturing and electrochemical texturing techniques, surface properties and potential applications will be presented.

Banks, Bruce A.↗
NASA NTRS1998

Fitting a Two-Component Scattering Model to Polarimetric SAR Data

Classification, decomposition and modeling of polarimetric SAR data has received a great deal of attention in the recent literature. The objective behind these efforts is to better understand the scattering mechanisms which give rise to the polarimetric signatures seen in SAR image data. In this Paper an approach is described, which involves the fit of a combination of two simple scattering mechanisms to polarimetric SAR observations. The mechanisms am canopy scatter from a cloud of randomly oriented oblate spheroids, and a ground scatter term, which can represent double-bounce scatter from a pair of orthogonal surfaces with different dielectric constants or Bragg scatter from a moderately rough surface, seen through a layer of vertically oriented scatterers. An advantage of this model fit approach is that the scattering contributions from the two basic scattering mechanisms can be estimated for clusters of pixels in polarimetric SAR images. The solution involves the estimation of four parameters from four separate equations. The model fit can be applied to polarimetric AIRSAR data at C-, L- and P-Band.

Freeman, A.↗
NASA NTRS2007

Fitting a Two-Component Scattering Model to Polarimetric SAR Data from Forests

Two simple scattering mechanisms are fitted to polarimetric synthetic aperture radar (SAR) observations of forests. The mechanisms are canopy scatter from a reciprocal medium with azimuthal symmetry and a ground scatter term that can represent double-bounce scatter from a pair of orthogonal surfaces with different dielectric constants or Bragg scatter from a moderately rough surface, which is seen through a layer of vertically oriented scatterers. The model is shown to represent the behavior of polarimetric backscatter from a tropical forest and two temperate forest sites by applying it to data from the National Aeronautic and Space Agency/Jet Propulsion Laboratory's Airborne SAR (AIRSAR) system. Scattering contributions from the two basic scattering mechanisms are estimated for clusters of pixels in polarimetric SAR images. The solution involves the estimation of four parameters from four separate equations. This model fit approach is justified as a simplification of more complicated scattering models, which require many inputs to solve the forward scattering problem. The model is used to develop an understanding of the ground-trunk double-bounce scattering that is present in the data, which is seen to vary considerably as a function of incidence angle. Two parameters in the model fit appear to exhibit sensitivity to vegetation canopy structure, which is worth further exploration. Results from the model fit for the ground scattering term are compared with estimates from a forward model and shown to be in good agreement. The behavior of the scattering from the ground-trunk interaction is consistent with the presence of a pseudo-Brewster angle effect for the air-trunk scattering interface. If the Brewster angle is known, it is possible to directly estimate the real part of the dielectric constant of the trunks, a key variable in forward modeling of backscatter from forests. It is also shown how, with a priori knowledge of the forest height, an estimate for the attenuation coefficient of the canopy can be obtained directly from the multi-incidence-angle polarimetric observations. This attenuation coefficient is another key variable in forward models and is generally related to the canopy density.

temperate forests↗
NASA NTRS2010

Serrating Nozzle Surfaces for Complete Transfer of Droplets

A method of ensuring the complete transfer of liquid droplets from nozzles in microfluidic devices to nearby surfaces involves relatively simple geometric modification of the nozzle surfaces. The method is especially applicable to nozzles in print heads and similar devices required to dispense liquid droplets having precise volumes. Examples of such devices include heads for soft printing of ink on paper and heads for depositing droplets of deoxyribonucleic acid (DNA) or protein solutions on glass plates to form microarrays of spots for analysis. The main purpose served by the present method is to ensure that droplets transferred from a nozzle have consistent volume, as needed to ensure accuracy in microarray analysis or consistent appearance of printed text and images. In soft printing, droplets having consistent volume are generated inside a print head, but in the absence of the present method, the consistency is lost in printing because after each printing action (in which a drop is ejected from a nozzle), a small residual volume of liquid remains attached to the nozzle. By providing for complete transfer of droplets (and thus eliminating residual liquid attached to the nozzle) the method ensures consistency of volume of transferred droplets. An additional benefit of elimination of residue is prevention of cross-contamination among different liquids printed through the same nozzle a major consideration in DNA microarray analysis. The method also accelerates the printing process by minimizing the need to clean a printing head to prevent cross-contamination. Soft printing involves a hydrophobic nozzle surface and a hydrophilic print surface. When the two surfaces are brought into proximity such that a droplet in the nozzle makes contact with the print surface, a substantial portion of the droplet becomes transferred to the print surface. Then as the nozzle and the print surface are pulled apart, the droplet is pulled apart and most of the droplet remains on the print surface. The basic principle of the present method is to reduce the liquid-solid surface energy of the nozzle to a level sufficiently below the intrinsic solid-liquid surface energy of the nozzle material so that the droplet is not pulled apart and, instead, the entire droplet volume becomes transferred to the print surface. In this method, the liquid-solid surface energy is reduced by introducing artificial surface roughness in the form of micromachined serrations on the inner nozzle surface (see figure). The method was tested in experiments on soft printing of DNA solutions and of deionized water through 0.5-mm-diameter nozzles, of which some were not serrated, some were partially serrated, and some were fully serrated. In the nozzles without serrations, transfer was incomplete; that is, residual liquids remained in the nozzles after printing. However, in every nozzle in which at least half the inner surface was serrated, complete transfer of droplets to the print surface was achieved.

Kim, Chang-Jin "CJ"↗
NASA NTRS1984

The Influence of Surface Topography on Polymer Friction

Current friction models for polymers are examined to determine their applicability in predicting the effects of roughness on friction. The two component, adhesion deformation model of friction predicts the variation of friction with the change in the sliding direction with respect to the lay direction on anisotropic rough surfaces. The two component model does not predict the change in friction with changes in roughness. A combination of an energy based model and a slip line deformation model may provide a friction model which could better represent measured friction.

Eiss, N. S., Jr.↗
NASA NTRS2024

Distributed Sand-Grain Roughness Effects on Blunt Body Hypersonic Transition and Heating

An experimental investigation of distributed sand-grain surface roughness effects on boundary-layer transition and convective heating has been performed. Two representative entry vehicle geometries, a spherical-cap aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic wind tunnel models of each geometry were fabricated with various roughness heights to simulate an ablated thermal protection system. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Aeroheating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations.

Brian R. Hollis↗
NASA NTRS1985

Periodic vortex shedding in the supersonic wake of a planar plate

Vortex sheets in the wake have been mainly studied in incompressible flows and in the transonic region. Heinemann et al. (1976) have shown that for the subsonic region the Strouhal number is nearly independent of the Mach number. Motallebi and Norbury (1981) have observed an increase in the Strouhal number in transonic supersonic flow at Mach numbers up to 1.25. The present investigation is concerned with an extension of the studies of vortex shedding to higher supersonic Mach numbers, taking into account questions regarding the possibility of a generation of stable von Karman vortex paths in the considered Mach number range. It is found that the vortex sheet observed in a supersonic wake behind a rough plate is only stable and reproducible in cases involving a certain surface roughness and certain aspects of trailing edge geometry.

Xing, W. F.↗
NASA NTRS1991

Analysis of images obtained by the Phobos 2 spacecraft

The reflection spectrum and density of the Martian satellite, Phobos, suggests that it may be a captured C-type asteroid and hence may contain relatively unaltered organic material from the early history of the solar system. Since there is evidence from isotopic anomalies that meteorites presumably derived from such asteroids contain preserved interstellar material, it is conceivable that evidence for interstellar matter might also be present on Phobos. The present research concerns interpretation of the chemical composition of Phobos' surface and analysis of images of Phobos taken by the FREGAT camera equipment aboard the Phobos 2 Spacecraft, including both disk-integrated and disk-resolved photometry. Because the surface of Phobos is a regolith, spectral information on the surface composition will be convolved with information on the surface texture. A primary goal was to untangle these effects. Unfortunately, the Phobos 1 Spacecraft lost contact with Earth during its transit to Mars, and Phobos 2 likewise lost contact after two months in orbit around Mars. Thus, the hovering phase of very close approach and the landing of instruments on the surface of Phobos did not take place, so no data on the elemental composition of the surface is available. However, 37 images were obtained of the satellite. The results include the first such observations at near infrared wavelengths, for which disk-integrated results show that the corresponding geometric albedo is quite small and very similar to the value in the blue. The resolved surface photometry was analyzed by developing new methods of radiative transfer in rough surface layers and a procedure referred to as statistical photoclinometry. The results provide root mean square surface slopes on scales from the order of 1 millimeter to 250 meters, albedo fluctuations, and corresponding correlation lengths.

Irvine, W. M.↗
NASA NTRS1994

The Martian atmospheric planetary boundary layer stability, fluxes, spectra, and similarity

This is the first analysis of the high frequency data from the Viking lander and spectra of wind, in the Martian atmospheric surface layer, along with the diurnal variation of the height of the mixed surface layer, are calculated for the first time for Mars. Heat and momentum fluxes, stability, and z(sub O) are estimated for early spring, from a surface temperature model and from Viking Lander 2 temperatures and winds at 44 deg N, using Monin-Obukhov similarity theory. The afternoon maximum height of the mixed layer for these seasons and conditions is estimated to lie between 3.6 and 9.2 km. Estimations of this height is of primary importance to all models of the boundary layer and Martian General Circulation Models (GCM's). Model spectra for two measuring heights and three surface roughnesses are calculated using the depth of the mixed layer, and the surface layer parameters and flow distortion by the lander is also taken into account. These experiments indicate that z(sub O), probably lies between 1.0 and 3.0 cm, and most likely is closer to 1.0 cm. The spectra are adjusted to simulate aliasing and high frequency rolloff, the latter caused both by the sensor response and the large Kolmogorov length on Mars. Since the spectral models depend on the surface parameters, including the estimated surface temperature, their agreement with the calculated spectra indicates that the surface layer estimates are self consistent. This agreement is especially noteworthy in that the inertial subrange is virtually absent in the Martian atmosphere at this height, due to the large Kolmogorov length scale. These analyses extend the range of applicability of terrestrial results and demonstrate that it is possible to estimate the effects of severe aliasing of wind measurements, to produce a models which agree well with the measured spectra. The results show that similarity theory developed for Earth applies to Mars, and that the spectral models are universal.

Tillman, James E.↗
NASA NTRS1994

On the relation between SMMR 37-GHz polarization difference and the rainfall over Africa and Australia

A major difficulty in interpreting coarse resolution satellite data in terms of land surface characteristics is unavailability of spatially and temporally representative ground observations. Under certain conditions rainfall has been found to provide a proxy measure for surface characteristics, and thus a relation between satellite observations and rainfall might provide an indirect approach for relating satellite data to these characteristics. Relationship between rainfall over Africa and Australia and 7-year average (1979-1985) polarization difference (PD) at 37 GHz from scanning multichannel microwave radiometer (SMMR) on board the Nimbus-7 satellite is studied in this paper. Quantitative methods have been used to screen (accept or reject) PD data considering antenna pattern, geolocation uncertainty, water contamination, surface roughness, and adverse effect of drought on the relation between rainfall and surface characteristics. The rainfall data used in the present analysis are climatologic averages and also 1979-1985 averages, and no screening has been applied to this data. The PD data has been screened considering only the location of rainfall stations, without any regard to rainfall amounts. The present analysis confirms a non-linear relation between rainfall and PD published previously.

Choudhury, Bhaskar J.↗
NASA NTRS1994

Damage Mechanisms and Controlled Crack Propagation in a Hot Pressed Silicon Nitride Ceramic

The subcritical growth of cracks from pre-existing flaws in ceramics can severely affect the structural reliability of a material. The ability to directly observe subcritical crack growth and rigorously analyze its influence on fracture behavior is important for an accurate assessment of material performance. A Mode I fracture specimen and loading method has been developed which permits the observation of stable, subcritical crack extension in monolithic and toughened ceramics. The test specimen and procedure has demonstrated its ability to generate and stably propagate sharp, through-thickness cracks in brittle high modulus materials. Crack growth for an aluminum oxide ceramic was observed to be continuously stable throughout testing. Conversely, the fracture behavior of a silicon nitride ceramic exhibited crack growth as a series of subcritical extensions which are interrupted by dynamic propagation. Dynamic initiation and arrest fracture resistance measurements for the silicon nitride averaged 67 and 48 J/sq m, respectively. The dynamic initiation event was observed to be sudden and explosive. Increments of subcritical crack growth contributed to a 40 percent increase in fracture resistance before dynamic initiation. Subcritical crack growth visibly marked the fracture surface with an increase in surface roughness. Increments of subcritical crack growth loosen ceramic material near the fracture surface and the fracture debris is easily removed by a replication technique. Fracture debris is viewed as evidence that both crack bridging and subsurface microcracking may be some of the mechanisms contributing to the increase in fracture resistance. A Statistical Fracture Mechanics model specifically developed to address subcritical crack growth and fracture reliability is used together with a damaged zone of material at the crack tip to model experimental results. A Monte Carlo simulation of the actual experiments was used to establish a set of modeling input parameters. It was demonstrated that a single critical parameter does not characterize the conditions required for dynamic initiation. Experimental measurements for critical crack lengths, and the energy release rates exhibit significant scatter. The resulting output of the model produces good agreement with both the average values and scatter of experimental measurements.

Calomino, Anthony Martin↗
NASA NTRS1994

Growing season boundary layer climate and surface exchanges in a subarctic lichen woodland

Between June and August 1990, observations were made at two surface micrometeorological towers near Schefferville Quebec (54 deg 52 min N, 66 deg 40.5 min W), one in a fen and one in the subarctic lichen woodland, and at four surface climatological stations. Data from these surface stations were supplemented by regular radiosonde launches. Supporting measurements of radiative components and soil temperatures allowed heat and moisture balances to be obtained at two sites. The overall surface meteorological experiment design and results of micrometeorological observations made on a 30-m tower in the lichen woodland are presented here. Seasonal variation in the heat and water vapor transport characteristics illustrate the marked effect of the late summer climatological shift in air mass type. During the first half of the summer, average valley sidewalls only 100 m high are sufficient to channel winds along the valley in the entire convective boundary layer. Channeling effects at the surface, known for some time at the long-term climate station in Schefferville, are observed both at ridge top and in the valley, possibly the response of the flow to the NW-SE orientation of valleys in the region. Diurnal surface temperature amplitude at ridge top (approximately equal to 10 C) was found to be half that observed in the valley. Relatively large differences in precipitation among these stations and the climatological station at Schefferville airport were observed and attributed to the local topography. Eddy correlation observations of the heat, moisture and momentum transports were obtained from a 30-m tower above a sparse (approximately equal to 616 stems/ha) black spruce lichen woodland. Properties of the turbulent surface boundary layer agree well with previous wind tunnel studies over idealized rough surfaces. Daytime Bowen ratios of 2.5-3 are larger than those reported in previous studies. Surface layer flux data quality was assessed by looking at the surface layer heat balance. Diurnal and seasonal scale heat budget imbalances were found. We suggest that unmeasured surface heat storage may be responsible for some of the observed imbalance. The presence of the unexplained residual in this and other studies of energy balance over forests casts a note of caution on the interpretation of energy balance components obtained using heat residual methods.

Fitzjarrald, David R.↗
NASA NTRS1996

On Soil Moisture Retrieval and Target Decomposition

In an earlier study, an empirical model was developed to infer soil moisture and surface roughness from radar data. The inversion technique was extensively tested over bare surfaces by comparing the estimated soil moisture to in situ measurements. The overall root mean square (RMS) error in the soil moisture estimate was found to be about 3.5% and the RMS error in the RMS height estimate was less than 0.35 cm absolute for bare or slightly vegetated surfaces. However, inversion results indicate that significant amounts of vegetation cause the algorithm to underestimate soil moisture and overestimate RMS height. Among the areas over which the inversion cannot be applied, the areas with intermediate vegetation cover are of particular interest as both the vegetation and the underlying bare surface affect the backscatter. This paper concentrates mostly on these areas. Using the full polarimetric information and the Cloude target decomposition approach, three different components of the target backscattering can be isolated. One of these three components can be identified as the surface component in the case of intermediate vegetation cover. Once the surface component of the scattering is isolated, the bare surface inversion can then be applied.

Dubois, Pascale C.↗
NASA NTRS1996

On Soil Moisture Retrieval and Target Decomposition

In an earlier study, an empirical model was developed to infer soil moisture and surface roughness from radar data. The inversion technique was extensively tested over bare surfaces by comparing the estimated soil moisture to in situ measurements. The overall RMS error in the soil moisture estimate was found to be 3.5% and the RMS error in the RMS height estimate was less than 0.35 cm absolute for bare or slightly vegetated surfaces. However, inversion results indicate that significant amounts of vegetation cause the algorithm to underestimate soil moisture and overestimate RMS height. Among the areas over which the inversion cannot be applied, the areas with intermediate vegetation cover are of particular interest as both the vegetation and the underlying bare surface affect the backscatter. This paper concentrates mostly on these areas. Using the full polarimetric information and the Cloude target decomposition approach. Three different components of the target backscattering can be isolated. One of these three components can be identified as the surface component in the case of intermediate vegetation cover. Once the surface component of the scattering is isolated, the bare surface inversion can then be applied.

Dubois, Pascale C.↗