Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanostructures evolution assessment and spectroscopic properties modification induced by electronic energy loss in KTaO 3 crystal

Modifications of micro/nanostructure and photoelectric properties under swift ion irradiation (645 MeV Xe 35+ ) of KTaO 3 crystal with varying electronic energy losses (7.2–31.4 keV/nm) and ion velocities (0.18–5.00 MeV/u) have been studied by combining experimental and calculated approaches. The i-TS calculations combined with molecular dynamics simulations are compared with the experimental observations, revealing the inner track fine structures from individual spherical defects to continuous ion tracks with core–shell morphologies, and a quantitative relationship, including the melting (0.42 eV/atom), damage (0.75 eV/atom), and amorphous (1.71 eV/atom) thresholds, is established to successfully predict the inner disorder/amorphous proportions and track damage morphologies. The surface nanostructures of nanohillocks (isolated or partial overlaps) and nanopits (serious overlaps) directly depend on the combined action of the deposited potential and kinetic energies of incident ions, which induce local melting and sublimation in the near-surface region. Owing to the decreased recombination and the increased separation efficiency between electrons and holes, the higher photogenerated charge carrier mobility enhanced the photocurrent effect, further optimizing the photoconductivity performance in Xe 35+ -irradiated KTaO 3 . Therefore, controlled defect engineering using the ion irradiation technique, as an effective strategy, could design tailored nanostructure systems and regulate photoelectric properties, further promoting the development of novel technological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Insights into Mechanisms of Screw Feeder Plugging by Heated Pine Forestry Residues Using in-situ and Correlative Microscopy

Increasing concerns about global carbon emissions due to fossil fuel use has created interest in renewable fuel alternatives, such as lignocellulosic biomass. With an estimated global biomass production probability ten-fold higher than projected need, functionalizing and scaling biomass conversion processes, like pyrolysis, is a promising component of a diverse sustainable energy program (Kan, Strezov, & Evans, 2016). Pyrolysis reactors employed in biomass conversion often encounter the known problem of screw feeder plugging, halting work and reducing efficiency of biorefineries. Although the screw feeder is not heated directly, conductive heat transfer from the fluidized bed pyrolysis reactor creates a temperature gradient, where particles experience temperatures between 22°C and 500°C from the time they enter the feeder to being emptied into the reactor (Digman, Joo, & Kim, 2009; Nieminen & Folke, 1982). The impact of unintentional heating on this highly variable feedstock may result in particle morphology modification, surface texture transformation, and the evolution of viscous compounds and may contribute to screw feeder plugging (Haas, Nimlos, & Donohoe, 2009; Ingram et al., 2008). We hypothesized that particles of various anatomical fractions (including needles, branches, bark, cambium, and whitewood) will experience dramatic changes during this heating regime, which will be characterized by decreased particle size, increased surface roughness, degradation of key structural macromolecules, and generation of viscous compounds that would result in increased particle friction and cohesion, contributing to screw feeder plugging.

biofuels↗
DOE OSTI2022

Molecular Structure of Adsorbed Water Phases in Silica Nanopores

The adsorption of water vapor in silica nanopores with different pore morphologies and surface hydrophilicities was studied to quantify the densities and thicknesses of the water sorption layers and deduce their molecular structures. Water adsorption to surface hydroxyls is described by a multilayer sorption model. At low pressure, the water adsorption isotherms are largely independent of pore size and the adsorbed amounts scale with the surface hydroxyl density. Adsorbed-phase densities corresponding to the adsorption of two water molecules per surface hydroxyl group are found in the first adsorbed water layer for a wide range of surface hydroxyl densities. The densities and layer thickness values found in narrow pores indicate that patchy adsorbed layers form if not enough water molecules exist for a full layer, which coexist with dry pore surface regions. This behavior indicates cooperative adsorption effects, i.e., a preference for the formation of hydrogen bonds between water molecules bound to surface hydroxyls. In narrow pores, pore condensation limits further growth of the sorption layer, and in larger pores and at the planar quartz surface, a second adsorbed water layer is formed, which can hold up to approximately 4 additional water molecules per surface hydroxyl group. The water molecules in these thicker adsorption layers arrange such that the sorption layer density is similar to the bulk water density. Pore confinement limitations on the sorption layers are observed in pores with radii of as large as 8 nm. Molecular dynamics modeling reveals two preferential orientations for water molecules adsorbing to surface hydroxyl groups and suggests an intralayer structuring in the adsorbed monolayer. Furthermore, adsorbed water molecules in the sorption layer are bonded to the surface hydroxyl group via the donation and acceptance of hydrogen bonds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Insights into Waterflooding in Hydrocarbon-Bearing Nanochannels of Varying Cross Sections from Mesoscopic Multiphase Flow Simulations

Waterflooding is one of the geotechnique used to recover fuel sources from nanoporous geological formations. The scientific understanding of the process that involves the multiphase flow of nanoconfined fluids, however, has lagged, mainly due to the complex nanopore geometries and chemical compositions. To enable benchmarked flow of nanoconfined fluids, the architected geomaterials, such as synthesized mesoporous silica with tunable pore shapes and surface chemical properties, are used for designing and conducting experiments and simulations. This work uses a modified many-body dissipative particle dynamics (mDPD) model with accurately calibrated parameters to perform parametric flow simulations for studying the influences of waterflooding driven power, pore shape, surface roughness, and surface wettability on the multiphase flow in heptane-saturated silica nanochannels. Remarkably, up to 80\% reduction in the effective permeability is found for water-driven heptane flow in a baseline 4.5 nm-wide slit channel, when compared with the Hagen–Poiseuille equation. In the 4.5 nm-wide channels with architected surface roughness, the flow rate is found either higher or lower than the baseline case, depending on the shape and size of cross-sections. High wettability of the solid surface to water is essential for achieving high recovery of heptane, regardless of surface roughness. When the solid surface is less wetting or non-wetting to water, the existence of an optimal waterflooding driven power is found to allow for the highest possible recovery. A detailed analysis on the evolution of the transient water-heptane interface in those nanochannels is presented to elucidate the underlying mechanisms that impact or dictate the multiphase flow behaviors.

58 GEOSCIENCES↗
DOE OSTI2024

Direct Conversion of CO 2 to Olefins over a Cr 2 O 3 /ZSM-5@CaO Cooperative and Bifunctional Material Under Isothermal Conditions

Direct conversion of point-source CO 2 into fine chemicals over cooperative and bifunctional materials (BFMs) – composed of adsorbents and catalysts – has emerged as a promising approach to improve the energy efficiency of the carbon capture and conversion processes. In this study, a bifunctional material consisting of Cr 2 O 3 /ZSM-5 catalyst and CaO adsorbent was developed and tested in the CO 2 -oxidative dehydrogenation of propane (CO 2 –ODHP) for reactive capture of CO 2 in a fixed bed reactor. First, CaO was prepared using two distinct methods: solid-state and citrate sol–gel. The citrate sol–gel method resulted in small and finely-distributed CaO particles, allowing more accessible sites for CO 2 adsorption. Consequently, a high CO 2 adsorption capacity of ~14 mmol/g was achieved with fast adsorption kinetics compared to CaO prepared by the solid-state method. The CaO adsorbent was then combined with the Cr 2 O 3 /ZSM-5 catalyst for BFM synthesis and tested in the CO 2 –ODHP process, targeting propylene production. The BFM was extensively characterized to provide insights into the BFM’s surface chemistry, morphology, and reaction mechanism in the reactive capture process of CO 2 –ODHP. The results revealed that under isothermal adsorption–reaction conditions at 600 °C, a propane conversion of 22.5%, a propylene selectivity of 55.3%, and an olefin selectivity of 67.3% were achieved. The excellent propylene selectivity was attributed to the catalyst acidity and redox property of the Cr 2 O 3 /ZSM-5 catalyst, which facilitated the reaction pathway of propane dehydrogenation in the process of CO 2 –ODHP. Overall, this study renders Cr 2 O 3 /ZSM-5@CaO as promising BFMs with high CO 2 capture capacity and catalytic activity for integrated CO 2 capture and conversion in the ODHP reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Feasibility of Algal Biochar, a Byproduct of Biofuel Production, as a Supplemental Cementitious Material

Algal biochar, as the solid residue of biofuel production from algal biomass, is reported to explore disposition options, aiming to lessen the liability or obstacles to biofuel production processes. However, landfills and open combustion lead to adverse environmental impacts. One way to add value to such wastes is to use them as admixtures in cementitious construction materials. This study aims to investigate the feasibility of algae-derived biochar as supplementary cementitious materials (SCM) at different water contents and mixture ratios. Algal biochar-cement composites were prepared with different algal biochar content as well as different water-to-cement (w/c) ratios, and the surface area, morphology, elemental, and mineralogical composition were characterized. To compensate for the high-water absorption of algal biochar, a small concentration of a superplasticizer was used since higher w/c ratios negatively impact strength. The mechanical performance of algal biochar-cement composites is compared with control composites using commercial silica fume as a typical commercial SCM. The findings suggest that algal biochar is a promising candidate to replace commercial SCM, like silica fume, since algal biochar-cement composites can reach comparable compressive strength and Young’s modulus to commercial pozzolan-cement materials with the same w/c ratio, though at later curing times, 33 days. Although the tensile strength of algal biochar-cement composites is statistically similar at 7 days, it is significantly lower at later curing times, and further investigation is required to improve this property. Algal biochar-based cement binders showed comparable embodied carbon to silica fume-based cement binders based on a cradle-to-gate lifecycle analysis. However, the ability of algal biochar to absorb large volumes of CO 2 over short periods of time, as measured in this study, makes this novel SCM an excellent alternative to reduce the embodied carbon of concrete structures cradle-to-grave at 1/10 of the cost. In conclusion, valorization of algae-derived solid waste provides great potential to reduce embodied carbon and brings credit to biofuel production and concrete-based construction.

algae-derived↗
DOE OSTI2024

Flower-shaped 2D crystals grown in curved fluid vesicle membranes

Abstract The morphologies of two-dimensional (2D) crystals, nucleated, grown, and integrated within 2D elastic fluids, for instance in giant vesicle membranes, are dictated by an interplay of mechanics, permeability, and thermal contraction. Mitigation of solid strain drives the formation of crystals with vanishing Gaussian curvature (i.e., developable domain shapes) and, correspondingly, enhanced Gaussian curvature in the surrounding 2D fluid. However, upon cooling to grow the crystals, large vesicles sustain greater inflation and tension because their small area-to-volume ratio slows water permeation. As a result, more elaborate shapes, for instance, flowers with bendable but inextensible petals, form on large vesicles despite their more gradual curvature, while small vesicles harbor compact planar crystals. This size dependence runs counter to the known cumulative growth of strain energy of 2D colloidal crystals on rigid spherical templates. This interplay of intra-membrane mechanics and processing points to the scalable production of flexible molecular crystals of controllable complex shape.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Nanoscopic cross-grain cation homogenization in perovskite solar cells

Multiscale cation inhomogeneity has been a major hurdle in state-of-the-art formamidinium–caesium (FA–Cs) mixed-cation perovskites for achieving perovskite solar cells with optimal power conversion efficiencies and durability. Although the field has attempted to homogenize the overall distributions of FA–Cs in perovskite films from both plan and cross-sectional views, our understanding of grain-to-grain cation inhomogeneity and ability to tailor it—that is, spatially resolving the FA–Cs compositional difference between individual grains down to the nanoscale—are lacking. Here we reveal that as fundamental building blocks of a perovskite film, individual grains exhibit cationic compositions deviating from the prescribed ideal composition, severely limiting the interfacial optoelectronic properties and perovskite layer durability. This performance-limiting nanoscopic factor is linked to thermodynamic-driven morphological grooving, leading to a segmented surface landscape. At the grain triple junctions, grooves form nanoscale groove traps that hinder the mixing of solid-state cations across grains and thus retard inter-grain FA–Cs mixing. By rationally modulating the heterointerfacial energies, we reduced the depth of these nanoscale groove traps by a factor of three, significantly improving cation homogeneity. Perovskite solar cells with shallower nanoscale groove traps demonstrate enhanced power conversion efficiencies (25.62%) and improved stability under various standardized international protocols. In conclusion, our work highlights the significance of resolving surface nano-morphologies for homogeneous properties of perovskites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Machine-learning-accelerated multimodal characterization and multiobjective design optimization of natural porous materials

Natural porous materials such as nanoporous clays are used as green and low-cost adsorbents and catalysts. The key factors determining their performance in these applications are the pore morphology and surface activity, which are typically represented by properties such as specific surface area, pore volume, micropore content and pH. The latter may be modified and tuned to specific applications through material processing and/or chemical treatment. Characterization of the material, raw or processed, is typically performed experimentally, which can become costly especially in the context of tuning of the properties towards specific application requirements and needing numerous experiments. In this work, we present an application of tree-based machine learning methods trained on experimental datasets to accelerate the characterization of natural porous materials. The resulting models allow reliable prediction of the outcomes of experimental characterization of processed materials (R2 from 0.78 to 0.99) as well as identification of key factors contributing to those properties through feature importance analysis. Furthermore, the high throughput of the models enables exploration of processing parameter–property correlations and multiobjective optimization of prototype materials towards specific applications. We have applied these methodologies to pinpoint and rationalize optimal processing conditions for clays exploitable in acid catalysis. One of such identified materials was synthesized and tested revealing appreciable acid character improvement with respect to the pristine material. Specifically, it achieved 79% removal of chlorophyll-a in acid catalyzed degradation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Predicting metal–metal interactions. I. The influence of strain on nanoparticle and metal adlayer stabilities

Strain-engineering of bimetallic nanomaterials is an important design strategy for developing new catalysts. In this paper, we introduce an approach for including strain effects into a recently introduced, density functional theory (DFT)-based alloy stability model. The model predicts adsorption site stabilities in nanoparticles and connects these site stabilities with catalytic reactivity and selectivity. Strain-based dependencies will increase the model’s accuracy for nanoparticles affected by finite-size effects. In addition to the stability of small nanoparticles, strain also influences the heat of adsorption of epitaxially grown metal-on-metal adlayers. In this respect, we successfully benchmark the strain-including alloy stability model with previous experimentally determined trends in the heats of adsorption of Au and Cu adlayers on Pt (111). For these systems, our model predicts stronger bimetallic interactions in the first monolayer than monometallic interactions in the second monolayer. We explicitly quantify the interplay between destabilizing strain effects and the energy gained by forming new metal–metal bonds. While tensile strain in the first Cu monolayer significantly destabilizes the adsorption strength, compressive strain in the first Au monolayer has a minimal impact on the heat of adsorption. Hence, this study introduces and, by comparison with previous experiments, validates an efficient DFT-based approach for strain-engineering the stability, and, in turn, the catalytic performance, of active sites in bimetallic alloys with atomic level resolution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Nanoscale morphological evolution of monocrystalline Pt surfaces during cathodic corrosion

This paper studies the cathodic corrosion of a spherical single crystal of platinum in an aqueous alkaline electrolyte, to map out the detailed facet dependence of the corrosion structures forming during this still largely unexplored electrochemical phenomenon. We find that anisotropic corrosion of the platinum electrode takes place in different stages. Initially, corrosion etch pits are formed, which reflect the local symmetry of the surface: square pits on (100) facets, triangular pits on (111) facets, and rectangular pits on (110) facets. We hypothesize that these etch pits are formed through a ternary metal hydride corrosion intermediate. In contrast to anodic corrosion, the (111) facet corrodes the fastest, and the (110) facet corrodes the slowest. For cathodic corrosion on the (100) facet and on higher-index surfaces close to the (100) plane, the etch pit destabilizes in a second growth stage, by etching faster in the (111) direction, leading to arms in the etch pit, yielding a concave octagon-shaped pit. In a third growth stage, these arms develop side arms, leading to a structure that strongly resembles a self-similar diffusion-limited growth pattern, with strongly preferred growth directions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Takagi–Taupin dynamical X-ray diffraction simulations of asymmetric X-ray diffraction from crystals: the effects of surface undulations

Dynamical X-ray diffraction simulations from crystals with surface undulations are reported. The Takagi–Taupin equations are applied and used to derive results in good agreement with experimental data reported in a separate paper [Macrander, Pereira, Huang, Kasman, Qian, Wojcik & Assoufid (2020). J. Appl. Cryst. 53, 789–792]. The development of Uragami [J. Phys. Soc. Jpn, (1969), 27, 147–154] is followed. Although previous work by Olekhnovich & Olekhnovich [Acta. Cryst. (1980), A36, 22–27] treated a crystal in the shape of a round cylinder, there do not seem to be any reports of previous dynamical X-ray diffraction treatments specifically for surface undulations. The significance of the present work is that it bridges the diffraction treatment of more classical dynamical diffraction theory, which assumes a flat surface, and the simple kinematic diffraction theory. Finally, the kinematic theory has, to date, been the primary means of simulating X-ray diffraction from surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring Surface Roughness Using Additive Manufacturing to Improve Internal Cooling

Abstract Surface roughness present on internal cooling channels produced with additive manufacturing has been previously shown to augment heat transfer and pressure loss to levels similar to traditionally cast turbulators. Given the ability of the surface roughness to improve the cooling performance of small cooling channels, the question arises on whether there is an optimal combination of random roughness features to maximize internal cooling performance. To investigate this question, test coupons with different surface roughness morphologies and magnitudes were manufactured by manipulating the parameters in the laser powder bed fusion additive manufacturing process. The coupons were tested to characterize the friction factor and Nusselt number of the cooling channels over a range of Reynolds numbers. Results showed that certain roughness combinations outperformed others, increasing the internal cooling performance of the channels. Additionally, manipulation of the performance using the process parameters allowed for reductions in build time, which could be useful for controlling component cost.

Engineering↗