Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shape analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Measured Effects of Turbulence on the Loudness and Waveforms of Conventional and Shaped Minimized Sonic Booms

Turbulence has two distinctive effects on sonic booms: there is distortion in the form of random perturbations that appear behind the shock waves, and shock rise times are increased randomly. A first scattering theory by S.C. Crow in the late 1960s quantified the random distortions, and Crow's theory was shown to agree with available flight test data. A variety of theories for the shock thickness have been presented, all supporting the role of turbulence in increasing rise time above that of a basic molecular-relaxation structure. The net effect of these phenomena on the loudness of shaped minimized booms is of significant interest. Initial analysis suggests that there would be no change to average loudness, but this had not been experimentally investigated. The January 2004 flight test of the Shaped Sonic Boom Demonstrator (SSBD), together with a reference unmodified F-5E, included a 12500- foot linear ground sensor array with 28 digitally recorded sensor sites. This data set provides an opportunity to re-test Crow's theory for the post-shock perturbations, and to examine the net effect of turbulence on the loudness of shaped sonic booms.

Plotkin, Kenneth J.↗
NASA NTRS1988

Effects of furnace temperature profile on the interface shape during Bridgman crystal growth

The effects of asymmetry in furnace temperature profile and pulling velocity on the crystal interface shape are demonstrated while neglecting the latent heat of solidification. It is concluded that the furnace temperature profile may be varied in order to influence the interface shape of the crystal. An exact thermal analysis is performed on the Bridgman technique by including the latent heat of solidification as a source term. The exact temperature field is obtained for the case of a flat melt-crystal interface. The earlier observation regarding the influence of furnace temperature profile on the crystal interface shape is confirmed and a criterion for a flat crystal interface is obtained. Various furnace temperature profiles are selected and their corresponding results are presented.

Taghavi, K.↗
NASA NTRS2012

An Analysis Technique/Automated Tool for Comparing and Tracking Analysis Modes of Different Finite Element Models

An analysis technique was developed to compare and track mode shapes for different Finite Element Models. The technique may be applied to a variety of structural dynamics analyses, including model reduction validation (comparing unreduced and reduced models), mode tracking for various parametric analyses (e.g., launch vehicle model dispersion analysis to identify sensitivities to modal gain for Guidance, Navigation, and Control), comparing models of different mesh fidelity (e.g., a coarse model for a preliminary analysis compared to a higher-fidelity model for a detailed analysis) and mode tracking for a structure with properties that change over time (e.g., a launch vehicle from liftoff through end-of-burn, with propellant being expended during the flight). Mode shapes for different models are compared and tracked using several numerical indicators, including traditional Cross-Orthogonality and Modal Assurance Criteria approaches, as well as numerical indicators obtained by comparing modal strain energy and kinetic energy distributions. This analysis technique has been used to reliably identify correlated mode shapes for complex Finite Element Models that would otherwise be difficult to compare using traditional techniques. This improved approach also utilizes an adaptive mode tracking algorithm that allows for automated tracking when working with complex models and/or comparing a large group of models.

Towner, Robert L.↗
NASA NTRS1988

Analysis of rotating flexible blades using MSC/NASTRAN

An overview is given of the use of MSC/NASTRAN in the analysis of rotating flexible blades. The geometrically nonlinear analysis using NASTRAN Solution Sequence 64 is discussed along with the determination of frequencies and mode shapes using Solution Sequence 63. Items unique to rotating blade analysis, such as setting angle, centrifugal softening effects, and hub flexibility, are emphasized.

Ernst, Michael A.↗
NASA NTRS2003

Quantification of Ice Accretions for Icing Scaling Evaluations

The comparison of ice accretion characteristics is an integral part of aircraft icing research. It is often necessary to compare an ice accretion obtained from a flight test or numerical simulation to one produced in an icing wind tunnel or for validation of an icing scaling method. Traditionally, this has been accomplished by overlaying two-dimensional tracings of ice accretion shapes. This paper addresses the basic question of how to compare ice accretions using more quantitative methods. For simplicity, geometric characteristics of the ice accretions are used for the comparison. One method evaluated is a direct comparison of the percent differences of the geometric measurements. The second method inputs these measurements into a fuzzy inference system to obtain a single measure of the goodness of the comparison. The procedures are demonstrated by comparing ice shapes obtained in the Icing Research Tunnel at NASA Glenn Research Center during recent icing scaling tests. The results demonstrate that this type of analysis is useful in quantifying the similarity of ice accretion shapes and that the procedures should be further developed by expanding the analysis to additional icing data sets.

Ruff, Gary A.↗
NASA NTRS2014

Flutter Analysis for Turbomachinery Using Volterra Series

The objective of this paper is to describe an accurate and efficient reduced order modeling method for aeroelastic (AE) analysis and for determining the flutter boundary. Without losing accuracy, we develop a reduced order model based on the Volterra series to achieve significant savings in computational cost. The aerodynamic force is provided by a high-fidelity solution from the Reynolds-averaged Navier-Stokes (RANS) equations; the structural mode shapes are determined from the finite element analysis. The fluid-structure coupling is then modeled by the state-space formulation with the structural displacement as input and the aerodynamic force as output, which in turn acts as an external force to the aeroelastic displacement equation for providing the structural deformation. NASA's rotor 67 blade is used to study its aeroelastic characteristics under the designated operating condition. First, the CFD results are validated against measured data available for the steady state condition. Then, the accuracy of the developed reduced order model is compared with the full-order solutions. Finally the aeroelastic solutions of the blade are computed and a flutter boundary is identified, suggesting that the rotor, with the material property chosen for the study, is structurally stable at the operating condition, free of encountering flutter.

computational fluid dynamics↗
DOE OSTI2023

Entrainment and aerosol effects on marine boundary-layer clouds: An investigation using ACE-ENA data from HOLODEC, G1, Pico and ACTOS (Final Report on Project Activities)

Marine boundary-layer clouds cover large regions of the globe and are known to strongly influence radiative balances. The microphysical properties and persistence of these clouds are tightly coupled with cloud-top entrainment and aerosol properties within both the boundary layer and the overlying free troposphere. This work addressed the microphysical response to entrainment and aerosol properties in marine stratocumulus clouds, using data from the Aerosol and Cloud Experiments in the Eastern North Atlantic (ACE-ENA) project. Specifically, emphasis was placed on 1. extensive in situ measurements taken with the Atmospheric Radiation Measurement (ARM) G1 aircraft using the Holographic Detector for Clouds (Holodec) instrument; 2. airborne measurements obtained with the helicopter-borne Airborne Cloud Turbulence Observation System (ACTOS) operated by the Leibniz Institute for Tropospheric Research (TROPOS) during the first phase of ACE-ENA; and 3. above-boundary-layer, mountain-top measurements taken at the Pico Mountain Observatory (OMP) by the research group of the co-investigator and scientists from TROPOS during the first phase of ACE-ENA. The work is aligned with the topic “Warm Boundary-Layer Atmospheric Processes.” Key results include the following. Data from the Holographic Detector for Clouds (Holodec) were reprocessed, refined, and validated through a careful instrument intercomparison, resulting in a high-quality dataset available on the ARM archive for ACE-ENA. High-resolution ACTOS measurements of thermodynamics, microphysical, and turbulence properties were analyzed to explore the behavior of the entrainment velocity at cloud top. Analysis of the vertical variability of cloud droplet size distribution shape suggests that mixing is more inhomogeneous near cloud top, and more homogeneous deeper into the cloud. Analysis of aerosol measurements from OMP explored the mixing state and cloud condensation nucleus properties, as well as the implications for radiative forcing. Finally, a machine learning algorithm was developed for identifying characteristic cloud droplet size distributions, and was employed to explore microphysical regimes in stratocumulus clouds observed during ACE-ENA. The characteristic size distributions are narrow, and only when spatially averaged do they produce the broad “gamma” distributions typically assumed in models. This implies that precipitation development should account for variability and correlations in the distribution shape as well as the number concentration of cloud droplets.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

An experimental wind-tunnel study to determine the divergence characteristics of a high-aspect ratio, forward-swept wing has been conducted in the NASA Langley Research Center (LaRC) Transonic Dynamics Tunnel (TDT). The rectangular wing used for this study had a panel aspect ratio of 9.16 (lambda = 0 deg.) and the sweep angle could be set at lambda = 0 deg., -15 deg., -30 deg., -45 deg., or -60 deg. A rectangular wing tip shape was tested at each of these sweep angles. In addition, a tip shape parallel to the freestream flow was tested for a wing sweep angle of lambda = -45 deg. The root of the wing was cantilever mounted to the wall of the wind tunnel. Divergence conditions were measured at M = 0.4 for each sweep angle and tip configuration tested. Subcritical response techniques were used to extrapolate to the divergence conditions during the wind-tunnel test. The primary objective of this test was to obtain data which could be used to verify for this configuration the divergence prediction capability of an aeroelastic analysis code. Subsonic lifting surface theory (kernel function) aerodynamics are utilized by this particular code. The analytical predictions of divergence were found to be significantly conservative at all forward sweep angles. At lambda = -45 deg., the analysis was 14 percent conservative. The effect of the two tip shapes on the divergence dynamic pressure was predicted accurately by the analysis. The divergence condition for the tip shape parallel to the flow occurred at a dynamic pressure 14 percent higher than the divergence condition with a rectangular tip shape.

Cole, S. R.↗
NASA NTRS1995

Spectral identification of minerals using imaging spectrometry data: Evaluating the effects of signal to noise and spectral resolution using the tricorder algorithm

The rapid development of sophisticated imaging spectrometers and resulting flood of imaging spectrometry data has prompted a rapid parallel development of spectral-information extraction technology. Even though these extraction techniques have evolved along different lines (band-shape fitting, endmember unmixing, near-infrared analysis, neural-network fitting, and expert systems to name a few), all are limited by the spectrometer's signal to noise (S/N) and spectral resolution in producing useful information. This study grew from a need to quantitatively determine what effects these parameters have on our ability to differentiate between mineral absorption features using a band-shape fitting algorithm. We chose to evaluate the AVIRIS, HYDICE, MIVIS, GERIS, VIMS, NIMS, and ASTER instruments because they collect data over wide S/N and spectral-resolution ranges. The study evaluates the performance of the Tricorder algorithm, in differentiating between mineral spectra in the 0.4-2.5 micrometer spectral region. The strength of the Tricorder algorithm is in its ability to produce an easily understood comparison of band shape that can concentrate on small relevant portions of the spectra, giving it an advantage over most unmixing schemes, and in that it need not spend large amounts of time reoptimizing each time a new mineral component is added to its reference library, as is the case with neural-network schemes. We believe the flexibility of the Tricorder algorithm is unparalleled among spectral-extraction techniques and that the results from this study, although dealing with minerals, will have direct applications to spectral identification in other disciplines.

Swayze, Gregg A.↗
NASA NTRS1987

Design sensitivity analysis and optimization of built-up structures

Developments during the course of the research in design sensitivity analysis and optimization of built-up structures, with both sizing and shape design variables, show clearly that a unified variational approach to design sensitivity analysis can yield derivatives of structural response with respect to design. Rigorous and practically computable results for structural components and built-up structures have been demonstrated and used to solve design optimization problems.

Choi, Kyung K.↗
NASA NTRS1989

Using NASTRAN To Analyze Vibrations Of Rotor Blades

Report gives information on use of NASTRAN computer program in finite-element analysis of rotating flexible blades like in compressors and on turboprop engines. Predicts steady-state components of deflections and stresses under centrifugal forces, generates data for plots of natural frequency versus rotational speed, and provides vibration-mode data for calculations of flutter. Describes use of NASTRAN solution sequence 64 for geometrical nonlinear analysis and solution sequence 63 for determination of frequencies and vibrational-mode shapes. Includes sample problem with NASTRAN input data. Emphasizes key factors in analysis of rotating blades, such as setting angle and centrifugal softening effects. Combined analyses of solution sequences 64 and 63 reduces computer time and number of output listings, in comparison with separate analyses. In central-processing-unit time cut in half.

Lawrence, Charles↗
NASA NTRS2008

Aerodynamic Analysis of Simulated Heat Shield Recession for the Orion Command Module

The aerodynamic effects of the recession of the ablative thermal protection system for the Orion Command Module of the Crew Exploration Vehicle are important for the vehicle guidance. At the present time, the aerodynamic effects of recession being handled within the Orion aerodynamic database indirectly with an additional safety factor placed on the uncertainty bounds. This study is an initial attempt to quantify the effects for a particular set of recessed geometry shapes, in order to provide more rigorous analysis for managing recession effects within the aerodynamic database. The aerodynamic forces and moments for the baseline and recessed geometries were computed at several trajectory points using multiple CFD codes, both viscous and inviscid. The resulting aerodynamics for the baseline and recessed geometries were compared. The forces (lift, drag) show negligible differences between baseline and recessed geometries. Generally, the moments show a difference between baseline and recessed geometries that correlates with the maximum amount of recession of the geometry. The difference between the pitching moments for the baseline and recessed geometries increases as Mach number decreases (and the recession is greater), and reach a value of -0.0026 for the lowest Mach number. The change in trim angle of attack increases from approx. 0.5deg at M = 28.7 to approx. 1.3deg at M = 6, and is consistent with a previous analysis with a lower fidelity engineering tool. This correlation of the present results with the engineering tool results supports the continued use of the engineering tool for future work. The present analysis suggests there does not need to be an uncertainty due to recession in the Orion aerodynamic database for the force quantities. The magnitude of the change in pitching moment due to recession is large enough to warrant inclusion in the aerodynamic database. An increment in the uncertainty for pitching moment could be calculated from these results and included in the development of the aerodynamic database uncertainty for pitching moment.

Bibb, Karen L.↗
NASA NTRS1991

Computer modeling of pulsed CO2 lasers for lidar applications

The experimental results will enable a comparison of the numerical code output with experimental data. This will ensure verification of the validity of the code. The measurements were made on a modified commercial CO2 laser. Results are listed as following. (1) The pulse shape and energy dependence on gas pressure were measured. (2) The intrapulse frequency chirp due to plasma and laser induced medium perturbation effects were determined. A simple numerical model showed quantitative agreement with these measurements. The pulse to pulse frequency stability was also determined. (3) The dependence was measured of the laser transverse mode stability on cavity length. A simple analysis of this dependence in terms of changes to the equivalent fresnel number and the cavity magnification was performed. (4) An analysis was made of the discharge pulse shape which enabled the low efficiency of the laser to be explained in terms of poor coupling of the electrical energy into the vibrational levels. And (5) the existing laser resonator code was changed to allow it to run on the Cray XMP under the new operating system.

Spiers, Gary D.↗
NASA NTRS2001

Retrieval of Polar Stratospheric Cloud Microphysical Properties from Lidar Measurements: Dependence on Particle Shape Assumptions

A retrieval algorithm has been developed for the microphysical analysis of polar stratospheric cloud (PSC) optical data obtained using lidar instrumentation. The parameterization scheme of the PSC microphysical properties allows for coexistence of up to three different particle types with size-dependent shapes. The finite difference time domain (FDTD) method has been used to calculate optical properties of particles with maximum dimensions equal to or less than 2 mu m and with shapes that can be considered more representative of PSCs on the scale of individual crystals than the commonly assumed spheroids. Specifically. these are irregular and hexagonal crystals. Selection of the optical parameters that are input to the inversion algorithm is based on a potential data set such as that gathered by two of the lidars on board the NASA DC-8 during the Stratospheric Aerosol and Gas Experiment 0 p (SAGE) Ozone Loss Validation experiment (SOLVE) campaign in winter 1999/2000: the Airborne Raman Ozone and Temperature Lidar (AROTEL) and the NASA Langley Differential Absorption Lidar (DIAL). The 0 microphysical retrieval algorithm has been applied to study how particle shape assumptions affect the inversion of lidar data measured in leewave PSCs. The model simulations show that under the assumption of spheroidal particle shapes, PSC surface and volume density are systematically smaller than the FDTD-based values by, respectively, approximately 10-30% and approximately 5-23%.

Reichardt, J.↗
NASA NTRS2009

Coupled parametric design of flow control and duct shape

A method for designing gas turbine engine components using a coupled parametric analysis of part geometry and flow control is disclosed. Included are the steps of parametrically defining the geometry of the duct wall shape, parametrically defining one or more flow control actuators in the duct wall, measuring a plurality of performance parameters or metrics (e.g., flow characteristics) of the duct and comparing the results of the measurement with desired or target parameters, and selecting the optimal duct geometry and flow control for at least a portion of the duct, the selection process including evaluating the plurality of performance metrics in a pareto analysis. The use of this method in the design of inter-turbine transition ducts, serpentine ducts, inlets, diffusers, and similar components provides a design which reduces pressure losses and flow profile distortions.

Florea, Razvan↗
NASA NTRS1980

The shape and stability of rotating liquid drops

Equilibrium shapes and stability of rotating drops held together by surface tension are found by computer-aided analysis that uses expansions in finite-element basis functions. Shapes are calculated as extrema of appropriate energies. Stability and relative stability are determined from curvatures of the energy surface in the neighborhood of the extremum. Families of axisymmetric, two-, three-, and four-lobed drop shapes are traced systematically. Bifurcation and turning points are located and the principle of exchange of stabilities is tested. The axisymmetric shapes are stable at low rotation rates but lose stability at the bifurcation to two-lobed shapes. Two-lobed drops isolated with constant angular momentum are stable. The results bear on experiments designed to further those of Plateau (1863).

Brown, R. A.↗