Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sans”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Atmospheric lateral and longitudinal turbulent length scales (measured at 600 to 800 meters above grade level)

NASA's Airborne Doppler Lidar System has been used to obtain a detailed 'instantaneous' mapping of horizontal spatial wind fields at 600-800 m elevations on the east side of the San Gorgonio Pass in California, in the form of checkerboard-fashion horizontal wind vectors spaced at 300 m intervals along and normal to the flight path. Spatial autocorrelations for the lateral and longitudinal components are ensemble-averaged, and integral turbulent length scales are computed for the wind fields' longitudinal and lateral directions. The flow in the region studied does not appear to be isotropic.

Cliff, W. C.↗

Interferometric radar measurement of ocean surface currents

A new method of measuring surface currents using an interferometric synthetic aperture radar is presented. An airborne implementation has been tested over San Francisco Bay near the time of maximum tidal flow, resulting in a map of the east-west component of the current. Only the line-of-sight component of velocity is measured by this technique. Where the SNR ratio was strongest, statistical fluctuations of less than 4 cm/s were observed for ocean patches of 60 x 60 m.

Goldstein, R. M.↗

Airborne Visible/Infrared Imaging Spectrometer (AVIRIS). A description of the sensor, ground data processing facility, laboratory calibration, and first results

The papers in this document were presented at the Imaging Spectroscopy 2 Conference of the 31st International Symposium on Optical and Optoelectronic Applied Science and Engineering, in San Diego, California, on 20 and 21 August 1987. They describe the design and performance of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) sensor and its subsystems, the ground data processing facility, laboratory calibration, and first results.

Vane, Gregg↗

Materials processing in space: An introduction to the G-480 payload

The Space Research and Development Organization at San Jose State University designed and developed a small self-contained payload (designated G-480 by NASA) which will perform four materials science experiments in low Earth orbit aboard the Space Shuttle. These experiments are categorized under two areas of investigation: corrosion and electrodeposition. While none of these experiments have previously been performed in space, both government and industry have expressed great interest in these and related areas of materials processing and engineering. A brief history of the G-480 project development is given along with a description of each experiment, followed by a tour of the G-480 payload. Expected results are discussed along with the function, design and operation of the payload hardware and software.

Butow, Steven J.↗

Vegetation studies on Vandenberg Air Force Base, California

Vandenburg Air Force Base, located in coastal central California with an area of 98,400 ac, contains resources of considerable biological significance. Available information on the vegetation and flora of Vandenburg is summarized and new data collected in this project are presented. A bibliography of 621 references dealing with vegetation and related topics related to Vanderburg was compiled from computer and manual literature searches and a review of past studies of the base. A preliminary floristic list of 642 taxa representing 311 genera and 80 families was compiled from past studies and plants identified in the vegetation sampling conducted in this project. Fifty-two special interest plant species are known to occur or were suggested to occur. Vegetation was sampled using permanent plots and transects in all major plant communities including chaparral, Bishop pine forest, tanbark oak forest, annual grassland, oak woodland, coastal sage scrub, purple sage scrub, coastal dune scrub, coastal dunes, box elder riparian woodland, will riparian woodland, freshwater marsh, salt marsh, and seasonal wetlands. Comparison of the new vegetation data to the compostie San Diego State University data does not indicate major changes in most communities since the original study. Recommendations are made for additional studies needed to maintain and extend the environmental data base and for management actions to improve resource protection.

Schmalzer, Paul A.↗

Finite element methodology for integrated flow-thermal-structural analysis

Papers entitled, An Adaptive Finite Element Procedure for Compressible Flows and Strong Viscous-Inviscid Interactions, and An Adaptive Remeshing Method for Finite Element Thermal Analysis, were presented at the June 27 to 29, 1988, meeting of the AIAA Thermophysics, Plasma Dynamics and Lasers Conference, San Antonio, Texas. The papers describe research work supported under NASA/Langley Research Grant NsG-1321, and are submitted in fulfillment of the progress report requirement on the grant for the period ending February 29, 1988.

Thornton, Earl A.↗

Crustal deformation in Great California Earthquake cycles

A model in which coupling is described approximately through a generalized Elsasser model is proposed for computation of the periodic crustal deformation associated with repeated strike-slip earthquakes. The model is found to provide a more realistic physical description of tectonic loading than do simpler kinematic models. Parameters are chosen to model the 1857 and 1906 San Andreas ruptures, and predictions are found to be consistent with data on variations of contemporary surface strain and displacement rates as a function of distance from the 1857 and 1906 rupture traces. Results indicate that the asthenosphere appropriate to describe crustal deformation on the earthquake cycle time scale lies in the lower crust and perhaps the crust-mantle transition zone.

Li, Victor C.↗

Trace gas emissions from a mid-latitude prescribed chaparral fire

Smoke-plume gas samples were collected at altitudes from 35-670 m above the ground over the San Dimas Experimental Forest during a 400-acre prescribed chaparral fire. Mean emission ratios relative to CO2 for CO, H2, CH4, and total nonmethane hydrocarbons were lower than previous values obtained for large biomass-burning field experiments. Comparison of samples from vigorously flaming and mixed stages of combustion revealed little differences in CO2 normalized emission ratios for these gases (except for N2O).

Cofer, Wesley R., III↗

Particulate emissions from a mid-latitude prescribed chaparral fire

Particulate emission from a 400-acre prescribed chaparral fire in the San Dimas Experimental Forest was investigated by collecting smoke aerosol on Teflon and glass-fiber filters from a helicopter, and using SEM and EDAX to study the features of the particles. Aerosol particles ranged in size from about 0.1 to 100 microns, with carbon, oxygen, magnesium, aluminum, silicon, calcium, and iron as the primary elements. The results of ion chromatographic analysis of aerosol-particle extracts (in water-methanol) revealed the presence of significant levels of NO2(-), NO3(-), SO4(2-), Cl(-), PO4(3-), C2O4(2-), Na(+), NH4(+), and K(+). The soluble ionic portion of the aerosol was estimated to be about 2 percent by weight.

Cofer, Wesley R., III↗

Marine stratocumulus cloud fields off the coast of southern California observed using Landsat imagery. I - Structural characteristics

The structural characteristics of stratocumulus cloud fields off the coast of southern California are investigated using Landsat Multispectral Scanner imagery. Twelve scenes in this area are examined along with three other stratocumulus scenes near San Francisco, over central Oregon, and in the Gulf of Mexico. Results from this initial study of stratocumulus clouds indicate that cloud-background threshold selection techniques based upon edge detection gradient assumptions are not appropriate for cloud segmentation and classification algorithms, cloud size distributions obey a power law, and cell horizontal aspect ratio increases with cell diameter. It was also found that stratocumulus clouds are bifractal in nature with fractal dimension of d of about 1.2 for cells with diameter D smaller than 0.5 km and d of about 1.5 for cells with D greater than 0.5 km; stratocumulus cloud fields appear to be homogeneous over regions of about 100 km x 100 km, a much smaller region than the 2.5-deg x 2.5-deg boxes to be used in the ISCCP regional averaging algorithms; and that structural properties of stratocumulus clouds observed off the coast of southern California are similar to those observed for stratocumulus clouds at three other locations.

Welch, R. M.↗

North America-Pacific plate boundary, an elastic-plastic megashear - Evidence from very long baseline interferometry

Data obtained by Mark III VLBI measurements of radio signals from permanent and mobile VLBI sites for 5.5 years of observations, starting in October 1982, were used to derive a picture of the earth crust deformation near the North America-Pacific plate boundary. The data, which included the vector positions of the VLBI sites and their rate of change, were used for comparison with a number of lithospheric deformation models based upon the concept that the motions of points near the North America-Pacific plate boundary are a linear combination of North America and Pacific velocities. The best of these models were found to fit 95 percent of the variance in 139 VLBI length and transverse velocity observations. Instantaneous shear deformation associated with plate tectonics is apparently developing in a zone 450 km wide paralleling the San Andreas Fault; some of this deformation will be recovered through elastic rebound, while the rest will be permanently set through plastic processes. Because the VLBI data have not been collected for a significant fraction of the earthquake cycle, they cannot discriminate between elastic and plastic behaviors.

Ward, Steven N.↗

Modeling surface deformations at complex strike-slip plate boundaries

Two new versions of the physical base-traction model of Li and Rice (1987) have been developed to study the loading processes and surface deformation near plate boundaries with geometric complexities, including a shallow creeping fault segment and two subparallel faults. Predictions of surface velocity and surface slip rate for the region between the San Andreas fault and the Pacific coast at the latitude of the Parkfield-Cholame segment using model parameters based on geologic, geodetic, and seismic considerations were found to be in good agreement with contemporary geodetic field data (not used in constrainning model parameters). Also, predicted surface velocity for the Salton Sea-Coachella Valley area were fit to recently derived contemporary geodetic data and very large baseline interferometry data, althoug here the model parameters are not well constrained.

Li, Victor C.↗

Geodetic evidence of the seismic potential at Parkfield, California

The average rates of line-length change and the rates of the shallow fault slip observed near Parkfield, California, were used to estimate the slip rate at depth on the San Andreas fault (SAF), using the Matsu'ura et al. (1986) procedure to model the aseismic deformation as a perturbation to steady block motion across the SAF. Five different models were tested against the data, with one model, featuring a nearly monotonic transition from creeping behavior on the northwest to locked behavior on the southeast, found to fit the data acceptably well. It is shown that stored elastic energy southeast of Parkfield could produce an earthquake of magnitude up to 8.0, that would have displacement and rupture length similar to historic earthquakes of the same size.

Sung, Li-Yu↗

Ground-based radiometric observations of emission and attenuation at 20.6, 31.65, and 90.0 GHz

During 1987, ground-based zenith-viewing observations of atmospheric thermal emission were made at frequencies of 20.6, 31.65, and 90.0 GHz. At the locations of the experiments, San Nicolas Island, California, and Denver, Colorado, radiosonde observations of temperature and humidity were also available. The data, after conversion to attenuation using the mean radiating temperature approximation, are processed to derive attenuation statistics. In addition, both clear and cloudy attenuation characteristics are examined and compared with the most recent theories. Finally, the predictability and interdependence of the three separate channels are examined.

Westwater, Ed R.↗

Determination of convergence rates across the Ventura Basin, Southern California, using GPS and historical triangulation

Comparison of angles from historical triangulation observations dating as far back as 1932 with Global Positions System (GPS) measurements taken in 1987 indicates that rapid convergence may be taking place on decade timescales in the central and eastern part of the Ventura basin, an east-west trending trough bounded by thrust faults. Changes in angles over this time were analyzed using Prescott's modified Frank's method and in terms of a model which assumes that the regions to the north and south of the basin are rigid blocks undergoing relative motion. For the two block model, inversion of the observed angle changes over the last 28 years for the relative motion vector leads to north-south convergence across the basin of 30 + or - 5 mm/yr, with a left lateral component of 10 + or - 1 mm/yr in the Fillmore-Santa Paula area in the central part of the basin. The modified Frank's method yields strain rates of approximately 2 microrad/yr in both the east and central parts of the basin for measurements spanning the 1971 San Fernando earthquake. Assuming no east-west strain yeilds north-south compression of approximately 3.5 + or - .2 cm/yr. Comparison of triangulation data prior to the earthquake shows no strain outside the margin of error. The convergence rates determined by geodetic techniques are consistent with geologic observations in the area. Such large geodetic deformation rates, with no apparent near-surface creep on the major thrust, can be understood if these faults become subhorizontal at relatively shallow depths and if the subhorizontal portions of the faults are creeping. An alternative explanation of the large displacement rates might be that the pumping of oil in the vicinity of the benchmarks caused large horizontal motions, although it is unlikely that meter scale horizontal motions are due to oil withdrawal. These and other hypotheses are evaluated to better constrain the tectonics of this active region.

Donnellan, Andrea↗

Probabilistic analysis for fatigue strength degradation of materials

This report presents the results of the first year of a research program conducted for NASA-LeRC by the University of Texas at San Antonio. The research included development of methodology that provides a probabilistic treatment of lifetime prediction of structural components of aerospace propulsion systems subjected to fatigue. Material strength degradation models, based on primitive variables, include both a fatigue strength reduction model and a fatigue crack growth model. Linear elastic fracture mechanics is utilized in the latter model. Probabilistic analysis is based on simulation, and both maximum entropy and maximum penalized likelihood methods are used for the generation of probability density functions. The resulting constitutive relationships are included in several computer programs, RANDOM2, RANDOM3, and RANDOM4. These programs determine the random lifetime of an engine component, in mechanical load cycles, to reach a critical fatigue strength or crack size. The material considered was a cast nickel base superalloy, one typical of those used in the Space Shuttle Main Engine.

Royce, Lola↗

Geodetic measurement of deformation in California

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 as part of the NASA Crustal Dynamics Project provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI-derived rates of deformation requires an examination of geologic information and more densely sampled ground-based geodetic data. In the first two of three related studies embodying this thesis triangulation and trilateration data measured on two regional networks are processed, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data have been utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geological structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. In the third study, VLBI data from stations distributed across the Pacific - North American plate boundary zone in the western United States are processed. The VLBI data have been used to constrain the integrated rate of deformation across portions of the continental plate boundary in California and to provide a tectonic framework to interpret regional geodetic and geologic studies.

Sauber, Jeanne Marie↗

Plate motions and deformations from geologic and geodetic data

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI derived rates of deformation requires an examination of geologic information and more densely sampled ground based geodetic data. Triangulation and trilateration data measured on two regional networks, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault, were processed. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data were utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geologic structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. VLBI data was also processed from stations distributed across the Pacific-North America plate boundary zone in the western U.S. The VLBI data were used to constrain the integrated rate of deformation across portions of the continental plate boundary in California and to provide a tectonic framework to interpret regional geodetic and geologic studies.

Jordan, Thomas H.↗