SEARCH · Engineering Papers

Results for “root”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Phytoxicity study of the products of wet oxidation of a representative biomass (lettuce)

In an attempt to verify the results reported previously concerning the phytotoxicity of wet-oxidation (wet-ox) products, lettuce solids were suspended in water and then heated to 548 K for 3.6 ksec (1 hr) under 4.1x10 to the -7 Pa (400 psig at 294 K) oxygen pressure and 1.52x10 to the 8th (1500 psig at 548 K) total pressure. Such treatment resulted in oxidation of 80% of the initial organic carbon to carbon dioxide. Thirty-three percent of the remaining organic carbon was present in acetic acid. Organic nitrogen in the feed was decreased 90% by the wet-ox treatment. Ammonia and nitrogen gas were the main nitrogen products. Analysis of the liquid product of wet-ox indicated that most of the minerals essential for plant growth were present. However, when tested using a lettuce-root growth-rate assay, the solution was toxic. This toxicity was not due to excessive salt or ammonia or to an improper pH. Analysis of the wet-ox solution revealed the presence of silver and chromium, thus implicating reactor corrosion as the cause of the phytotoxicity. Both cation and anion exchange resins removed the silver and the toxicity of the liquid effluent, indicating silver as the toxic component. Uptake of both silver and chromium by lettuce roots correlated with diminished root growth. Toxicity of the solution from wet-ox was not observed when precautions were taken to minimize contact of the liquid in the reactor with the metal reactor components.

Onisko, B. L.↗

NASA NTRS1983

Benchmark cyclic plastic notch strain measurements

Plastic strains at the roots of notched specimens of Inconel 718 subjected to tension-compression cycling at 650 C are reported. These strains were measured with a laser-based technique over a gage length of 0.1 mm and are intended to serve as 'benchmark' data for further development of experimental, analytical, and computational approaches. The specimens were 250 mm by 2.5 mm in the test section with double notches of 4.9 mm radius subjected to axial loading sufficient to cause yielding at the notch root on the tensile portion of the first cycle. The tests were run for 1000 cycles at 10 cpm or until cracks initiated at the notch root. The experimental techniques are described, and then representative data for the various load spectra are presented. All the data for each cycle of every test are available on floppy disks from NASA.

Sharpe, W. N., Jr.↗

NASA NTRS1982

Benchmark notch test for life prediction

Aircraft gas turbine engine components are subjected to severe stress, temperature, and environmental conditions. Economic and reliabilty demands have prompted inordinate effort in development of analytic methods to predict stresses and strains in aircraft engines. There remains, however, the need to check or verify these analytical methodologies against actual experimental data measurements. The laser interferometric strain displacement gage was recognized as having the potential to accomplish this task and was employed in this program. The actual strains incurred at the root of a discontinuity in cyclically loaded test samples subjected to inelastic deformation at high temperature where creep deformation readily occur were measured. The steady-state, cyclic stress-strain response at the root of the discontinuity in the tested samples was analyzed for comparison with the measured results. A comprehensive set of local notch root strain measurements for a variety of load patterns in an Inconel 718 notch specimen at 649 C (1200 F) was obtained and documented using the laser interferometric strain displacement gage.

Domas, P. A.↗

NASA NTRS1985

A Residuals Approach to Filtering, Smoothing and Identification for Static Distributed Systems

An approach for state estimation and identification of spatially distributed parameters embedded in static distributed (elliptic) system models is advanced. The method of maximum likelihood is used to find parameter values that maximize a likelihood functional for the system model, or equivalently, that minimize the negative logarithm of this functional. To find the minimum, a Newton-Raphson search is conducted that from an initial estimate generates a convergent sequence of parameter estimates. For simplicity, a Gauss-Markov approach is used to approximate the Hessian in terms of products of first derivatives. The gradient and approximate Hessian are computed by first arranging the negative log likelihood functional into a form based on the square root factorization of the predicted covariance of the measurement process. The resulting data processing approach, referred to here by the new term of predicted data covariance square root filtering, makes the gradient and approximate Hessian calculations very simple. A closely related set of state estimates is also produced by the maximum likelihood method: smoothed estimates that are optimal in a conditional mean sense and filtered estimates that emerge from the predicted data covariance square root filter.

Rodriguez, G.↗

NASA NTRS1985

A comparison of smooth specimen and analytical simulation techniques for notched members at elevated temperatures

Experimental strain measurements have been made at the highly strained regions on notched plate specimens that were made of Hastelloy X. Tests were performed at temperatures up to 1,600 F. Variable load patterns were chosen so as to produce plastic and creep strains. Were appropriate, notch root stresses were experimentally estimated by subjecting a smooth specimen to the measured notch root strains. The results of three analysis techniques are presented and compared to the experimental data. The most accurate results were obtained from an analysis procedure that used a smooth specimen and the Neuber relation to simulate the notch root stress-strain response. When a generalized constitutive relation was used with the Neuber relation, good results were also obtained, however, these results were not as accurate as those obtained when the smooth specimen was used directly. Finally, a general finite element program, ANYSIS, was used which resulted in acceptable solutions, but, these were the least accurate predictions.

Martin, J. F.↗

NASA NTRS1986

Effects of some geometric variations on missile aerodynamic characteristics at supersonic speeds

A summary of some results from tests of a wing-body general research missile model is presented for a Mach number range up to 4.63. A basic ogive-cylinder body with a length-to-diameter ratio of 10 was used to which was attached a series of wing planforms. The planforms included a family of delta wings and a family of rectangular wings having a constant root chord but varying spans so that wings of constant exposed area could be compared. In addition, a cranked-tip planform was included and a rectangular planform with reduced chord. Some results are presented for wing-body-tail configurations - one utilizing a cranked wing planform and one with wings having a constant root chord and span, but tip chords that were 0, 20, and 40 percent of the root chord.

Spearman, M. L.↗

NASA NTRS1986

Effects of some geometric variations on missile aerodynamic characteristics at supersonic speeds

Spearman, M. L.↗

NASA NTRS1987

Structural tailoring using the SSME/STAEBL code

Space Shuttle Main Engine/Structural Tailoring of Engine Blades (SSME/STAEBL) was developed by systematically modifying and enhancing the STAEBL code developed by Pratt and Whitney under contract to NASA Lewis Research Center. STAEBL was designed for application to gas turbine blade design. Typical design variables include blade thickness distribution and root chord. Typical constraints include resonance margins, root stress, and root to chord ratios. In this program, the blade is loaded by centrifugal forces only. Additions and modifications of STAEBL included in SSME/STAEBL include (1) thermal stress analysis; (2) gas dynamic (pressure) loads; (3) temperature dependent material and thermal properties; (4) forced vibrations; (5) tip displacement constraints; (6) single crystal material analysis; (7) blade cross section stacking offsets; and (8) direct time integration algorithm for transient dynamic response. Capabilities are also included which permit data transfer from finite element models and stand-alone analysis.

Rubinstein, Robert↗

NASA NTRS1986

Numerical aspects of different Kalman filter implementations

A theoretical analysis is made of the error propagation due to numerical roundoff for four different Kalman filter implementations: the conventional Kalman filter, the square root covariance filter, the square root information filter, and the Chandrasekhar square root filter. An experimental analysis is performed to validate the new insights gained by the theoretical analysis.

Verhaegen, M.↗

NASA NTRS1987

A study of some approximations in the modeling of a coupled rotor/fuselage aeromechanical system

Equations of motion for a three-bladed hingeless rotor coupled to a gimbal-supported fuselage are developed. A brief derivation of the equations is presented, including the assumptions made, the ordering scheme, and a discussion of both the source of the aerodynamic axial load term and the reason for differences due to hinge sequence. The solution of the equations is discussed, including linearization, the use of multiblade coordinates to eliminate periodic coefficients, and specialization to a root-sprung model. The treatment of the blade root offset by using an ordering scheme to neglect higher-order terms is found to affect results in pitch and roll. A small aerodynamic loading term in the blade axial direction has a significant effect at large collective pitch settings, as does the choice of a flap-lag or a lag-flap transformation sequence for blade motion. The results for a hingeless rotor also differ significantly from those for the root-sprung model when the nonrotating natural frequencies are matched.

Blelloch, P. A.↗

NASA NTRS1990

An enhanced integrated aerodynamic load/dynamic optimization procedure for helicopter rotor blades

An enhanced integrated aerodynamic load/dynamic optimization procedure is developed to minimize vibratory root shears and moments. The optimization is formulated with 4/rev vertical and 3/rev inplane shears at the blade root as objective functions and constraints, and 4/rev lagging moment. Constraints are also imposed on blade natural frequencies, weight, autorotational inertia, centrifugal stress, and rotor thrust. The 'Global Criteria Approach' is used for formulating the multi-objective optimization. Design variables include spanwise distributions of bending stiffnesses, torsional stiffness, nonstructural mass, chord, radius of gyration, and blade taper ratio. The program CAMRAD is coupled with an optimizer, which consists of the program CONMIN and an approximate analysis, to obtain optimum designs. The optimization procedure is applied to an advanced rotor as a reference design. Optimum blade designs, obtained with and without a constraint on the rotor thrust, are presented and are compared to the reference blade. Substantial reductions are obtained in the vibratory root forces and moments. As a byproduct, improvements are also found in some performance parameters, such as total power required, which were not considered during optimization.

Chattopadhyay, Aditi↗

NASA NTRS1991

Comparison of analysis and experiment for dynamics of low-contact-ratio spur gears

Low-contact-ratio spur gears were tested in NASA gear-noise-rig to study gear dynamics including dynamic load, tooth bending stress, vibration, and noise. The experimental results were compared with a NASA gear dynamics code to validate the code as a design tool for predicting transmission vibration and noise. Analytical predictions and experimental data for gear-tooth dynamic loads and tooth-root bending stress were compared at 28 operating conditions. Strain gage data were used to compute the normal load between meshing teeth and the bending stress at the tooth root for direct comparison with the analysis. The computed and measured waveforms for dynamic load and stress were compared for several test conditions. These are very similar in shape, which means the analysis successfully simulates the physical behavior of the test gears. The predicted peak value of the dynamic load agrees with the measurement results within an average error of 4.9 percent except at low-torque, high-speed conditions. Predictions of peak dynamic root stress are generally within 10 to 15 percent of the measured values.

Oswald, Fred B.↗

NASA NTRS1990

An enhanced integrated aerodynamic load/dynamic approach to optimum rotor blade design

An enhanced integrated aerodynamic load/dynamic optimization procedure is developed to minimize vibratory root shears and moments. The optimization is formulated with 4/rev vertical and 3/rev inplane shears at the blade root as objective functions and constraints, and 4/rev lagging moment. Constraints are also imposed on blade natural frequencies, weight, autorotational inertia, contrifugal stress, and rotor thrust. The Global Criteria Approach is used for formulating the multi-objective optimization. Design variables include spanwise distributions of bending stiffnesses, torsional stiffness, nonstructural mass, chord, radius of gyration, and blade taper ratio. The program CAMRAD is coupled with an optimizer, which consists of the program CONMIN and an approximate analysis, to obtain optimum designs. The optimization procedure is applied to an advanced rotor as a reference design. Optimum blade designs, obtained with and without a constraint on the rotor thrust, are presented and are compared to the reference blade. Substantial reductions are obtained in the vibratory root forces and moments. As a byproduct, improvements are also found in some performance parameters, such as total power required, which were not considered during optimization.

Chattopadhyay, Aditi↗

NASA NTRS1992

Deformational mass transport and invasive processes in soil evolution

Channels left in soil by decayed roots and burrowing animals allow organic and inorganic precipitates and detritus to move through soil from above, to depths at which the minuteness of pores restricts further passage. Consecutive translocation-and-root-growth phases stir the soil, constituting an invasive, dilatational process which generates cumulative strains. Below the depths thus affected, mineral dissolution by descending organic acids leads to internal collapse; this softened/condensed precursor horizon is then transformed into soil via biological activity that mixes and expands the evolving residuum through root and micropore-network invasion.

Brimhall, George H.↗

NASA NTRS1993

Method of measuring cross-flow vortices by use of an array of hot-film sensors

The invention is a method for measuring the wavelength of cross-flow vortices of air flow having streamlines of flow traveling across a swept airfoil. The method comprises providing a plurality of hot-film sensors. Each hot-film sensor provides a signal which can be processed, and each hot-film sensor is spaced in a straight-line array such that the distance between successive hot-film sensors is less than the wavelength of the cross-flow vortices being measured. The method further comprises determining the direction of travel of the streamlines across the airfoil and positioning the straight-line array of hot film sensors perpendicular to the direction of travel of the streamlines, such that each sensor has a spanwise location. The method further comprises processing the signals provided by the sensors to provide root-mean-square values for each signal, plotting each root-mean-square value as a function of its spanwise location, and determining the wavelength of the cross-flow vortices by noting the distance between two maxima or two minima of root-mean-square values.

Agarwal, Aval K.↗

NASA NTRS1993

Structural tailoring of aircraft engine blade subject to ice impact constraints

Results are presented for the minimum weight design of SR2 unswept blade made of (titanium/graphite-epoxy/titanium) sub s fiber composite. The blade which is rotating at high RPM is subject to ice impact. The root chord length, blade thicknesses at five stations, and graphite-epoxy ply orientation are chosen as design variables. Design constraints are placed on the behavior variables: local leading edge strain and root damage parameter (combined stress failure criteria) as a function due to ice impact, maximum spanwise centrifugal stress at the root of the deformed blade due to local damage, first three natural frequencies, and resonance margin after impact. The method of feasible directions is employed to solve the inequality constrained minimization problem. The effect of ice speed and the ice impact location on the final design are discussed.

Reddy, E. S.↗

NASA NTRS1992

Structural tailoring of aircraft engine blade subject to ice impact constraints

In this paper, results are presented for the minimum weight design of SR2 unswept blade made of (Titanium/Graphite-Epoxy/Titanium)s fiber composite. The blade which is rotating at high RPM is subject to ice impact. The root chord length, blade thicknesses at five stations, and graphite-epoxy ply orientation are chosen as design variables. The design constraints are placed on the behavior variables: leading edge strain and root damage parameter due to ice impact, maximum post-impact bending stress at the root due to rotation, first three natural frequencies and resonance margin after impact. The method of feasible directions is employed to solve the inequality constrained minimization problem. The effect of ice speed and the ice impact location on the final design are discussed.

Reddy, E. S.↗

NASA NTRS1988

Foliage Plants for Improving Indoor Air Quality

NASA's research with foliage houseplants during the past 10 years has produced a new concept in indoor air quality improvement. This new and exciting technology is quite simple. Both plant leaves and roots are utilized in removing trace levels of toxic vapors from inside tightly sealed buildings. Low levels of chemicals such as carbon monoxide and formaldehyde can be removed from indoor environments by plant leaves alone, while higher concentrations of numerous toxic chemicals can be removed by filtering indoor air through the plant roots surrounded by activated carbon. The activated carbon absorbs large quantities of the toxic chemicals and retains them until the plant roots and associated microorganisms degrade and assimilate these chemicals.

Wolverton, B. C.↗