Results for “oxidative degradation” — Page 40

NASA NTRS1984

Laboratory degradation of Kapton in a low energy oxygen ion beam

An atomic oxygen ion beam, accelerated from a tunable microwave resonant cavity, was used at Lewis Research Center to bombard samples of the widely used polyimide Kapton. The Kapton experienced degradation and mass loss at high rates, which may be comparable to those found in Space Shuttle operations if the activation energy supplied by the beam enabled surface reactions with the ambient oxygen. The simulation reproduced the directionality (ram-wake dependence) of the degradation, the change in optical properties of the degraded materials, and the structure seen in scanning electron micrographs of samples returned on the Shuttle Trails with a substituted argon ion beam produced no rapid degradation. Energy Dispersive X-ray Analysis (EDAX) showed significant surface composition changes in all bombarded samples. Mass loss rates and surface composition changes are discussed in terms of the possible oxidation chemistry of the interaction. Finally, the question of how the harmful degradation of materials in low Earth orbit can be minimized is addressed.

Ferguson, D. C.↗

NASA NTRS1983

Laboratory degradation of Kapton in a low energy oxygen ion beam

An atomic oxygen ion beam, accelerated from a tunable microwave resonant cavity, was used at Lewis Research Center to bombard samples of the widely used polyimide Kapton. The Kapton experienced degradation and mass loss at high rates, which may be comparable to those found in Space Shuttle operations if the activation energy supplied by the beam enabled surface reactions with the ambient oxygen. The simulation reproduced the directionality (ram-wake dependence) of the degradiation, the change in optical properties of the degraded materials, and the structure seen in scanning electron micrographs of samples returned on the Shuttle Trails with a substituted argon ion beam produced no rapid degradation. Energy Dispersive X-ray Analysis (EDAX) showed significant surface composition changes in all bombarded samples. Mass loss rates and surface composition changes are discussed in terms of the possible oxidation chemistry of the interaction. Finally, the question of how the harmful degradation of materials in low earth orbit can be minimized is addressed.

Ferguson, D. C.↗

DOE OSTI2025

Catalyst Deactivation Modes of PdO/γ-Al 2 O 3 Catalysts for Lean Methane Oxidation

PdO/γ-Al 2 O 3 catalysts are one of the most active catalytic components for the complete oxidation of methane. Under reaction conditions, especially in a wet feed, the catalysts suffer severe performance degradation. This study establishes a series of testing protocols to systematically investigate the causes of catalyst deactivation under methane oxidation reaction conditions. Four distinct catalyst deactivation modes are identified. Two of the deactivation modes are directly related to H 2 O, either from the feed gas or as a part of the reaction products, with one (Mode 2) being attributed to the formation of surface hydroxyl groups and the other (Mode 3) to the competitive adsorption of H 2 O on the catalysts. The impact of the two deactivation modes is acute and severe but reversible. In contrast, the other two deactivation modes are gradual and persistent but irreversible. Both modes are induced by CH 4 oxidation reaction, with the impact of a wet feed (Mode 4) being substantially more severe than that of a dry feed (Mode 1). The major cause of the irreversible catalyst deactivation is attributed to surface reconstruction of PdO nanoparticles, which behaves as a passivation layer lowering the number of coordinately unsaturated Pd sites for CH 4 activation. Although the passivation layer is relatively stable against thermal or hydrothermal treatment, it is not completely inert. Formation and partial regeneration of the passivation layer is a highly dynamic process and heavily depends on the reaction temperature: a lower reaction temperature (≤ 450 ℃) can lead to quicker catalyst deactivation; but a higher reaction temperature (between 500 – 550 ℃) can result in a greater extent of catalyst deactivation.

PdO/γ-Al2O3↗

DOE OSTI2020

Surface-Activated Corrosion in Tin–Lead Halide Perovskite Solar Cells

Mixed tin–lead halide perovskite solar cells have promising power conversion efficiencies, but long-term stability is still a challenge. Here, we examine the stability of a 60:40 tin–lead perovskite to better understand diminished device performance upon thermal treatment, both in ambient and inert atmosphere. Operando X-ray diffraction shows a stable bulk structure of the perovskite absorber, leading to the hypothesis that surface chemistry dominates the degradation mechanism. X-ray photoelectron spectroscopy reveals two new observations post-thermal annealing that accompany previously reported Sn 4+ evolution: (i) the formation of I 3 – intermediates preceding I 2 loss at the surface and (ii) evidence of under-coordinated tin and lead surface sites (Sn δ<2+ and Pb δ<2+ , respectively) in inert and ambient conditions. These two species indicate an activated corrosion (i.e., both oxidation and reduction) process at the surface as a possible chemical pathway for degradation, which is expected to be accelerated under operando voltage and light biases.

14 SOLAR ENERGY↗

NASA NTRS2003

Use of Atomic Oxygen for the Determination of Document Alteration

Atomic oxygen, which normally is found only the near Earth space environment, causes oxidation and erosion of polymers on spacecraft. The development of technology to prevent this degradation has required NASA to develop ground laboratory facilities that generate atomic oxygen. Atomic oxygen has also been found to be able to oxidize most types of ink from a variety of types of pens. The use of atomic oxygen to identify alteration of documents has been investigated and is reported. Results of testing indicates that for many types of ink, pen, and paper, identification of document alteration of pen and ink numbers and evidence of alteration can be made visible by exposing the questionable writing to atomic oxygen. Atomic oxygen provides discrimination because different inks may oxidize at different rates, the amount of time between delayed alteration may add to ink thickness at crossings, and the end of pen strokes tend to have much thicker ink deposits than the rest of the character. Examples and techniques of using atomic oxygen to identify document alteration indicate that the technology can, in many but not all cases, provide discrimination between original and altered documents.

Banks, Bruce A.↗

DOE OSTI2026

Complete Phase Transformation of Ir Nanowire Network into Defect-Rich Oxide Catalyst for High-Performance PEM Water Electrolysis

Iridium-based catalysts remain the most reliable option for the oxygen evolution reaction (OER) in proton exchange membrane water electrolyzers (PEMWEs). However, their high cost and limited performance represent critical barriers to the commercialization of this green hydrogen production technology. Herein, we report the creation of a metallic Ir nanowire network (IrNWN), which exhibits superior OER performance through its in-situ transition into an oxide structure with high intrinsic activity. At a low loading of 0.25 mgIr/cm2 in PEMWEs, IrNWN achieved a current density of 3.13 A/cm2 at a cell voltage of 1.8 V, outperforming the commercial Ir-based catalyst and surpassing the Department of Energy (DOE) 2026 technical target. Moreover, the high activity of IrNWN was maintained for 900 hours in a durability test at 2 A/cm2, showing a low degradation rate of 0.042 mV/hour. Structural analysis of the electrochemically oxidized IrNWN revealed the presence of mixed Ir oxidation states and a high density of surface terminal oxygen groups (μ1-O), which contributed to a reduced energy barrier for the rate-determining O-O coupling step.

oxygen evolution reaction↗

DOE OSTI2025

Critical insights into the steam electrolysis electrode in protonic ceramic cells for hydrogen production

Intermediate-temperature protonic ceramic electrolysis cells (PCECs), which combine the benefits of both lower- and higher-temperature electrolysis, are among the most efficient technologies for the production of green hydrogen. To ensure economic competitiveness and broad adoption, ongoing innovations in cell materials are essential to improve durability and reduce costs. The water oxidation half-reaction at the anode is a key area for improvement as it is a major contributor to performance degradation and efficiency loss in PCECs. Current anode designs, which are largely derived from solid oxide electrolysis cells, fail to address the specific requirements for PCECs under realistic operating conditions. Here, this Perspective highlights the unique challenges faced by PCEC anodes, focusing on the impact of high steam concentrations and the critical role of proton-coupled electron-transfer mechanisms—factors that are absent in solid oxide electrolysis cells. Furthermore, we explore design principles for advancing anodes tailored for PCECs, offering guidance for future research and development in this promising field.

Electrocatalysis↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRS2011

Modeling the effects of hydrogen and dose rate sensitivity in CMOS and bipolar technologies

Low dose rate (LDR) and high dose rate (HDR) experiments on field-oxide-field-effect-transistors (FOXFETs) and gated lateral pnp (GLPNP) bipolar transistors indicate that there is a dose rate enhancement factor (EF) associated with radiation-induced degradation. This EF is also affect by the presence of hydrogen in the oxide. In this work, we developed a one dimensional (1-D) numerical calculations code to investigate the key mechanisms that describe the dose rate sensitivity and the effect of hydrogen on dose rate effects. We used a finite-difference methodology for the numerical calculations that allow for computing solutions for the densities of the mobile species as well as for the electrostatic potential at nodes contained within a mesh superimposed on the solution domain. Results from calculations of damage EF indicate that oxide thickness, distribution of hole traps and hole capture cross-section affect dose rate sensitivity. In addition, calculations show that molecular hydrogen cracking at positively charged defects may be a key reaction relating hydrogen and dose rate response. Comparison to experimental data on bipolar and CMOS devices results in good agreement with the dose rate calculations of interface trap buildup

Barnaby, Hugh↗

DOE OSTI2023

Phenothiazines Rapidly Induce Laccase Expression and Lignin-Degrading Properties in the White-Rot Fungus Phlebia radiata

Phlebia radiata is a widespread white-rot basidiomycete fungus with significance in diverse biotechnological applications due to its ability to degrade aromatic compounds, xenobiotics, and lignin using an assortment of oxidative enzymes including laccase. In this work, a chemical screen with 480 conditions was conducted to identify chemical inducers of laccase expression in P. radiata. Among the chemicals tested, phenothiazines were observed to induce laccase activity in P. radiata, with promethazine being the strongest laccase inducer of the phenothiazine-derived compounds examined. Secretomes produced by promethazine-treated P. radiata exhibited increased laccase protein abundance, increased enzymatic activity, and an enhanced ability to degrade phenolic model lignin compounds. Transcriptomics analyses revealed that promethazine rapidly induced the expression of genes encoding lignin-degrading enzymes, including laccase and various oxidoreductases, showing that the increased laccase activity was due to increased laccase gene expression. Finally, the generality of promethazine as an inducer of laccases in fungi was demonstrated by showing that promethazine treatment also increased laccase activity in other relevant fungal species with known lignin conversion capabilities including Trametes versicolor and Pleurotus ostreatus.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Degradation Mechanism Due to Water Ingress Effect on the Top Contact of Cu(In,Ga)Se2 Solar Cells

The impact of moisture ingress on the surface of copper indium gallium diselenide (CIGS) solar cells was studied. While industry-scale modules are encapsulated in specialized polymers and glass, over time, the glass can break and the encapsulant can degrade. During such conditions, water can potentially degrade the interior layers and decrease performance. The first layer the water will come in contact with is the transparent conductive oxide (TCO) layer. To simulate the impact of this moisture ingress, complete devices were immersed in deionized water. To identify the potential sources of degradation, a common window layer for CIGS devices—a bilayer of intrinsic zinc oxide (i-ZnO) and conductive indium tin oxide (ITO)—was deposited. The thin films were then analyzed both pre and post water soaking. To determine the extent of ingress, dynamic secondary ion mass spectroscopy (SIMS) was performed on completed devices to analyze impurity diffusion (predominantly sodium and potassium) in the devices. The results were compared to device measurements, and indicated a degradation of device efficiency (mostly fill factor, contrary to previous studies), potentially due to a modification of the alkali profile.

14 SOLAR ENERGY↗

DOE OSTI2025

Dual‐Gradient Construction on Li‐Rich Cathodes for High Stability Lithium Battery

Abstract The practical applications of high‐energy Li‐rich layered oxides (LLOs) have been hindered by the severe performance degradation including voltage decay and capacity fading. The gradient construction toward high‐activity interior and high‐stability exterior, typically realized by gradually changed transition metal (TM) gradient in LLOs, can alleviate the performance degradation to certain degrees. In this study, a gradient design of Al/Mg dopants is demonstrated for the TM‐gradient LLOs to further harmonize the high‐activity interior and high‐stability exterior, thereby forming the dual (TM and doping) gradient. As a result, superior capacity retention of 86% and a minor voltage decay of 0.54 mV cycle −1 are achieved at 1 C after 300 cycles. The improved electrochemical stability of the dual‐gradient LLO is attributed to the enhanced surface stability and suppressed bulk structure degeneration of LLOs upon electrochemical cycling. The dual‐gradient design serves as an important approach to fabricate high‐performance bulk LLOs toward applications.

Wu, Tianhao↗

DOE OSTI2023

Engineering Rhodosporidium toruloides for production of 3-hydroxypropionic acid from lignocellulosic hydrolysate

Microbial production of valuable bioproducts is a promising route towards green and sustainable manufacturing. The oleaginous yeast, Rhodosporidium toruloides, has emerged as an attractive host for the production of biofuels and bioproducts from lignocellulosic hydrolysates. 3-hydroxypropionic acid (3HP) is an attractive platform molecule that can be used to produce a wide range of commodity chemicals. This study focuses on establishing and optimizing the production of 3HP in R. toruloides. As R. toruloides naturally has a high metabolic flux towards malonyl-CoA, we exploited this pathway to produce 3HP. Upon finding the yeast capable of catabolizing 3HP, we then implemented functional genomics and metabolomic analysis to identify the catabolic pathways. Deletion of a putative malonate semialdehyde dehydrogenase gene encoding an oxidative 3HP pathway was found to significantly reduce 3HP degradation. We further explored monocarboxylate transporters to promote 3HP transport and identified a novel 3HP transporter in Aspergillus pseudoterreus by RNA-seq and proteomics. Combining these engineering efforts with media optimization in a fed-batch fermentation resulted in 45.4 g/L 3HP production. This represents one of the highest 3HP titers reported, and the highest titer produced from lignocellulosic hydrolysate to the best of our knowledge. This work demonstrates microbial production of 3HP in R. toruloides from lignocellulosic hydrolysate at high titers, and it represents a significant step toward enabling industrial production of 3HP in the future.

3-Hydroxypropionic acid↗

DOE OSTI2026

Toward Sustainable Lithium Recovery: A Universal Hydrothermal Approach for Lithium Extraction

The rapid growth of lithium-ion battery (LIB) deployment presents critical challenges in sustainable end-of-life management and raw material recovery. Conventional pyrometallurgical and hydrometallurgical methods suffer from high energy demand, lithium loss, and complex wastewater treatment. This study established a universal, highly efficient, and sustainable hydrothermal route for lithium extraction and material recovery from various spent lithium-ion battery cathodes using 1,2,4,5-benzenetetracarboxylic acid (BTCA). The optimized process achieved over 99% lithium leaching efficiency for lithium iron phosphate (LFP) and LiNi x Mn y Co 1–x–y O 2 (NMC), with transition metal coleaching below 1%. It was also broadly applicable to lithium manganese oxide, lithium cobalt oxide, and black mass, achieving 98.5%, 98.95%, and 94.06% leaching efficiencies, respectively. The extracted lithium was directly converted into battery-grade lithium sources, while transition metals were recovered as oxides. Unreacted BTCA was efficiently regenerated and reused without degradation. Electrochemical evaluation confirmed that cathode materials synthesized with recovered lithium exhibit comparable performance to commercial products. Compared to conventional hydrometallurgy, the BTCA-based process increased revenue by over 40% and reduced greenhouse gas emissions by up to 39%. This closed-loop, chemistry-agnostic strategy offered a scalable and economically viable solution for industrial LIB recycling, enabling resource circularity and reducing dependency on primary critical materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Surface coating by mechanofusion modulates bulk charging pathways and battery performance of Ni-rich layered cathodes

Ni-rich layered oxides as high-capacity battery cathodes suffer from degradation at high voltages. Here, we utilize a dry surface modification method, mechanofusion (MF), to achieve enhanced battery stability. The simplicity, high yield, and flexibility make it cost-effective and highly attractive for processing at the industrial scale. The underlying mechanisms responsible for performance improvement are unveiled by a systematic study combining multiple probes, e.g., 3D nano-tomography, spectroscopic imaging, in situ synchrotron diffraction, and finite element analysis (FEA). MF affects the bulk crystallography by introducing partially disordered structure, microstrain, and local lattice variation. Furthermore, the crack initiation and propagation pattern during delithiation are regulated and the overall mechanical fracture is reduced after such surface coating. We validate that MF can alter the bulk charging pathways. Such a synergic effect between surface modification and bulk charge distribution is fundamentally important for designing next-generation battery cathode materials.

25 ENERGY STORAGE↗