Results for “module efficiency” — Page 40

NASA NTRS2003

Effects of a Scanning Reflectarray Antenna on Modulated Data Modeled

The ferroelectric reflectarray is a new type of scanning antenna under development for space and ground communications and radar applications at the NASA Glenn Research Center. The reflectarray offers tremendous cost, gain, and efficiency advantages in comparison to the state-of-the-art phased arrays, but there is an inherent intersymbol interference (ISI) problem with digital communication data streams processed through the array because of the way the reflectarray is operated. This interference stems from the fact that the antenna beam is formed by the superposition of reflected waves from the array elements. The delays from the elements to the observation point of each wave differ. Ferroelectric phase shifters are designed to compensate for the modulo-2p phase differences so that the waves will constructively interfere at the sinusoidal carrier level; however, the delays of the integer-number multiple of the carrier period are not compensated for. This lack of compensation causes ISI in digital modulated signals. ISI has not been a problem with analog modulations and low-rate digital modulations since the distortion (or ISI) introduced is negligible. The problem becomes acute when the data rate gets higher, and the electrical size of the array gets bigger. Moreover, there are intrinsic transient effects associated with the phase shifters and the controller that executes the algorithm to direct the beam. That is, phase shifter updates to redirect the beam may be initiated simultaneously, but nonlinearity will cause different settling times. The ISI problem and other effects ultimately limit the size (gain) and data rate of the reflectarray. An ISI analysis was required to prove or disprove the suitability of the reflectarray antenna for high-rate digitally modulated signals and to give guidance for determining antenna parameters. In this research, the nature of the ISI of the reflectarray has been mathematically modeled.

Romanofsky, Robert R.↗

NASA NTRS1974

A technique for correcting transmission errors in delta modulation channels

The delta modulator is a relatively new device which has found wide application in voice encoding. Two main difficulties in using this device for video encoding and processing is that it slope overloads and 'rings' and that channel errors produce a DC level shift. An algorithm is developed which is easily implemented and which significantly reduces 'picture streaks' due to the production of DC level shifts by channel errors. The algorithm can be made adaptive whereby the insertion rate of the pulse code modulation (PCM) codeword needed for correction can be adjusted depending on the strength of the channel noise. This yields a more efficient use of bandwidth. Further, the resulting signal can still be processed further using line-to-line correlation to remove the remaining 'streaks'.

Ali, M. Z.↗

NASA NTRS1976

Effect of premixing quality on oxides of nitrogen in gas turbine combustors foi HC

Experiments were conducted to determine the effectiveness of several premixing prevaporizing gas turbine combustor designs in reducing formation of oxides of nitrogen at the supersonic cruise condition. An atomized spray from a single injector mounted on the axis of the mixer tube produced a high initial concentration of fuel near the axis and only moderate premixed conditions entering the combustor. A fuel spray produced by 12 flush-mounted normal injection orifices in the mixer tube wall produced a good initial despersion of fuel and resulted in nearly complete premixing. Oxides of nitrogen emission levels of the order of 0.2 g NO2/kg fuel were obtained at 99 percent combustion efficiency at an equivalence ratio of 0.4. Overall total pressure drop was less than 3 percent through the 1-meter combustor module.

Roffe, G.↗

NASA NTRS1976

Stark effect applicable to optically pumped far-infrared laser

Absorption measurements at CO2 laser frequencies were carried out as a function of Stark fields and CH3OH gas pressures to assess the effect of low electric field Stark tuning on methanol absorption at the P(12) 9.4 micron CO2 laser line, in a continuing search for coherent emitters at submillimeter wavelengths (far infrared). The line center absorption coefficient is found to increase five-fold with a 2.3 kV/cm Stark field at the 220 mtorr methanol pressure optimal for methanol far infrared lasing. The low electric field Stark tuning encourages efforts to enhance the pumping efficiency of a methanol far infrared laser at its normal optimum operating pressure, and suggests that significant Stark field induced frequency modulation of the far IR laser output is feasible.

Claspy, P. C.↗

NASA NTRS1988

Efficient detection and signal parameter estimation with applications to high dynamic GPS receivers

A novel technique for simultaneously detecting data and estimating the parameters of a received carrier signal phase modulated by unknown data and experiencing very high Doppler, Doppler rate, etc. is discussed. Such a situation arises, for example, in the case of Global Positioning Systems (DPS) where the signal parameters are directly related to the position, velocity and acceleration of the GPS receiver. The proposed scheme is based upon first estimating the received signal local (data dependent) parameters over two consecutive bit periods, followed by the detection of a possible jump in these parameters. The presence of a detected jump signifies a data transition which is then removed from the received signal. This effectively demodulated signal is then processed to provide the estimates of global (data independent) parameters of the signal related to the position, velocity, etc. of the receiver. One of the key features of the proposed algorithm is the introduction of two different schemes which can provide an improvement of up to 3 dB over the conventional implementation of Kalman filter as applied to phase and frequency estimation, under low to medium signal-to-noise ratio conditions.

Kumar, R.↗

NASA NTRS1987

Location of planar targets in three space from monocular images

Many pieces of existing and proposed space hardware that would be targets of interest for a telerobot can be represented as planar or near-planar surfaces. Examples include the biostack modules on the Long Duration Exposure Facility, the panels on Solar Max, large diameter struts, and refueling receptacles. Robust and temporally efficient methods for locating such objects with sufficient accuracy are therefore worth developing. Two techniques that derive the orientation and location of an object from its monocular image are discussed and the results of experiments performed to determine translational and rotational accuracy are presented. Both the quadrangle projection and elastic matching techniques extract three-space information using a minimum of four identifiable target points and the principles of the perspective transformation. The selected points must describe a convex polygon whose geometric characteristics are prespecified in a data base. The rotational and translational accuracy of both techniques was tested at various ranges. This experiment is representative of the sensing requirements involved in a typical telerobot target acquisition task. Both techniques determined target location to an accuracy sufficient for consistent and efficient acquisition by the telerobot.

Cornils, Karin↗

NASA NTRS1992

High power GaInAs lasers with distributed Bragg reflectors

Single-mode strained-layer lasers have been fabricated which use buried second-order gratings for distributed Bragg reflectors. The lasers contain a strained GaInAs quantum well in the active region and operate in an edge emitting fashion with CW powers in excess of 110 mW. Single longitudinal and transverse mode operation is maintained at about 971.9 nm up to 42 mW. Total power conversion efficiencies as high as 28 percent have been observed. The longitudinal and transverse mode behavior is stable under 90 percent amplitude modulation with 50 percent duty cycle pulses at 10 kHz and 10 MHz. Preliminary life-test data at 40 C also indicate room temperature lifetimes in excess of 45,000 hours.

O'Brien, S.↗

NASA NTRS1994

A 32-GHz solid-state power amplifier for deep space communications

A 1.5-W solid-state power amplifier (SSPA) has been demonstrated as part of an effort to develop and evaluate state-of-the-art transmitter and receiver components at 32 and 35 GHz for future deep space missions. Output power and efficiency measurements for a monolithic millimeter-wave integrated circuit (MMIC)-based SSPA are reported. Technical design details for the various modules and a thermal analysis are discussed, as well as future plans.

Wamhof, P. D.↗

NASA NTRS2003

Software Requirements Analysis as Fault Predictor

Waiting until the integration and system test phase to discover errors leads to more costly rework than resolving those same errors earlier in the lifecycle. Costs increase even more significantly once a software system has become operational. WE can assess the quality of system requirements, but do little to correlate this information either to system assurance activities or long-term reliability projections - both of which remain unclear and anecdotal. Extending earlier work on requirements accomplished by the ARM tool, measuring requirements quality information against code complexity and test data for the same system may be used to predict specific software modules containing high impact or deeply embedded faults now escaping in operational systems. Such knowledge would lead to more effective and efficient test programs. It may enable insight into whether a program should be maintained or started over.

Wallace, Dolores↗

NASA NTRS2009

Handbook for Designing MMOD Protection

Spacecraft are subject to micro-meteoroid and orbital debris (MMOD) impact damage which have the potential to degrade performance, shorten the mission, or result in catastrophic loss of the vehicle. Specific MMOD protection requirements are established by NASA for each spacecraft early in the program/project life, to ensure the spacecraft meets desired safety and mission success goals. Both the design and operations influences spacecraft survivability in the MMOD environment, and NASA considers both in meeting MMOD protection requirements. The purpose of this handbook is to provide spacecraft designers and operations personnel with knowledge gained by NASA in implementing effective MMOD protection for the International Space Station, Space Shuttle, and various science spacecraft. It has been drawn from a number of previous publications [10-14], as well as new work. This handbook documents design and operational methods to reduce MMOD risk. In addition, this handbook describes tools and equations needed to design proper MMOD protection. It is a living report, in that it will be updated and re-released periodically in future with additional information. Providing effective and efficient MMOD protection is essential for ensuring safe and successful operations of spacecraft and satellites. A variety of shields protect crew modules, external pressurized vessels and critical equipment from MMOD on the International Space Station (ISS). Certain Space Shuttle Orbiter vehicle systems are hardened from MMOD impact, and operational rules are established to reduce the risk from MMOD (i.e., flight attitudes are selected and late inspection of sensitive thermal protection surfaces are conducted to reduce MMOD impacts). Science spacecraft include specific provisions to meet MMOD protection requirements in their design (for example, Stardust & GLAST). Commercial satellites such as Iridium and Bigelow Aerospace Genesis spacecraft incorporate MMOD protection. The development of low-weight, effective MMOD protection has enabled these spacecraft missions to be performed successfully. This handbook describes these shielding techniques. For future exploration activities to the Moon and Mars, implementing high-performance MMOD shielding will be necessary to meet protection requirements with minimum mass penalty. A current area of technology development in MMOD shielding is the incorporation of sensors to detect and locate MMOD impact damage. Depending on the type of sensor the signals from the sensor can be processed to infer the location of the impact and the extent of damage. The objective of the sensors is to locate critical damage that would endanger the spacecraft or crew immediately or during reentry (such as an air leak from crew module or critical damage to thermal protection system of reentry vehicles). The information from the sensors can then be used with repair kits, patch kits, hatch closure or other appropriate remedial techniques to reduce MMOD risk.

Arnold, Jim↗

NASA NTRS2007

NASA Tech Briefs, July 2007

Topics covered include: Miniature Intelligent Sensor Module; "Smart" Sensor Module; Portable Apparatus for Electrochemical Sensing of Ethylene; Increasing Linear Dynamic Range of a CMOS Image Sensor; Flight Qualified Micro Sun Sensor; Norbornene-Based Polymer Electrolytes for Lithium Cells; Making Single-Source Precursors of Ternary Semiconductors; Water-Free Proton-Conducting Membranes for Fuel Cells; Mo/Ti Diffusion Bonding for Making Thermoelectric Devices; Photodetectors on Coronagraph Mask for Pointing Control; High-Energy-Density, Low-Temperature Li/CFx Primary Cells; G4-FETs as Universal and Programmable Logic Gates; Fabrication of Buried Nanochannels From Nanowire Patterns; Diamond Smoothing Tools; Infrared Imaging System for Studying Brain Function; Rarefying Spectra of Whispering-Gallery-Mode Resonators; Large-Area Permanent-Magnet ECR Plasma Source; Slot-Antenna/Permanent-Magnet Device for Generating Plasma; Fiber-Optic Strain Gauge With High Resolution And Update Rate; Broadband Achromatic Telecentric Lens; Temperature-Corrected Model of Turbulence in Hot Jet Flows; Enhanced Elliptic Grid Generation; Automated Knowledge Discovery From Simulators; Electro-Optical Modulator Bias Control Using Bipolar Pulses; Generative Representations for Automated Design of Robots; Mars-Approach Navigation Using In Situ Orbiters; Efficient Optimization of Low-Thrust Spacecraft Trajectories; Cylindrical Asymmetrical Capacitors for Use in Outer Space; Protecting Against Faults in JPL Spacecraft; Algorithm Optimally Allocates Actuation of a Spacecraft; and Radar Interferometer for Topographic Mapping of Glaciers and Ice Sheets.

Source record↗

NASA NTRS2010

High Pressure Angle Gears: Comparison to Typical Gear Designs

A preliminary study has been completed to determine the feasibility of using high-pressure angle gears in aeronautic and space applications. Tests were conducted in the NASA Glenn Research Center (GRC) Spur Gear Test Facility at speeds up to 10,000 rpm and 73 N*m (648 in.*lb) for 3.18, 2.12, and 1.59 module gears (8, 12, and 16 diametral pitch gears), all designed to operate in the same test facility. The 3.18 module (8-diametral pitch), 28 tooth, 20deg pressure angle gears are the GRC baseline test specimen. Also, 2.12 module (12-diametral pitch), 42 tooth, 25deg pressure angle gears were tested. Finally 1.59 module (16-diametral pitch), 56 tooth, 35deg pressure angle gears were tested. The high-pressure angle gears were the most efficient when operated in the high-speed aerospace mode (10,000 rpm, lubricated with a synthetic turbine engine oil), and produced the lowest wear rates when tested with a perfluoroether-based grease. The grease tests were conducted at 150 rpm and 71 N*m (630 in.*lb).

Handschuh, Robert F.↗

NASA NTRS2017

Methods and Apparatus for Autonomous Robotic Control

Sensory processing of visual, auditory, and other sensor information (e.g., visual imagery, LIDAR, RADAR) is conventionally based on "stovepiped," or isolated processing, with little interactions between modules. Biological systems, on the other hand, fuse multi-sensory information to identify nearby objects of interest more quickly, more efficiently, and with higher signal-to-noise ratios. Similarly, examples of the OpenSense technology disclosed herein use neurally inspired processing to identify and locate objects in a robot's environment. This enables the robot to navigate its environment more quickly and with lower computational and power requirements.

Versace, Massimiliano↗

NASA NTRS2018

Methods and Apparatus for Autonomous Robotic Control

Sensory processing of visual, auditory, and other sensor information (e.g., visual imagery, LIDAR, RADAR) is conventionally based on "stovepiped," or isolated processing, with little interactions between modules. Biological systems, on the other hand, fuse multi-sensory information to identify nearby objects of interest more quickly, more efficiently, and with higher signal-to-noise ratios. Similarly, examples of the OpenSense technology disclosed herein use neurally inspired processing to identify and locate objects in a robot's environment. This enables the robot to navigate its environment more quickly and with lower computational and power requirements.

Versace, Massimiliano↗

NASA NTRSDate not supplied

Application of Stuffed Whipple Shield to Robotic Spacecraft

Protection of human life onboard the International Space Station (ISS) requires reinforced shielding of crewed modules to prevent penetration of micro-meteoroid and orbital debris (MMOD), while optimizing the necessary mass for that application. An efficient way to achieve that protection consists in combining metal plates with ceramic and Kevlar fabrics in critical areas, a configuration known as the “Stuffed Whipple Shield”. In robotic spacecraft, fuel tanks are particularly vulnerable to MMOD impacts due to their pressurized contents and thin walls. Risk assessment of the Plankton, Aerosol, Cloud, ocean Ecosystem (PACE) spacecraft using the Bumper3-Sat hypervelocity impact simulation tool demonstrated that the risk of propulsion tank damage due to MMOD particles coming from the ram direction (Launch Vehicle Adapter side) violated NASA requirements to limit the generation of orbital debris and threatened mission success. To mitigate the risk and achieve compliance, the basic configuration of the ISS Stuffed Whipple shield was scaled down and adapted to become a tank shield in the spacecraft ram direction. This paper will describe the adaptation of the ISS Stuffed Shield to a robotic spacecraft, while also comparing the effectiveness of the proposed shield design with more traditional single-wall and double-wall alternatives used in robotic spacecraft under similar conditions.

Ivonne M. Rodriguez↗

NASA NTRSDate not supplied

Validation of Loci-Stream for Autogenous Pressurization of Cryogenic Propellant Tank

Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.

cryogenic fluid management↗

NASA NTRSDate not supplied

Validation of Loci-Stream for Autogenous Pressurization of Cryogenic Propellant Tank

Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.

CFM↗

NASA NTRSDate not supplied

Validation of Two Phase Flow Modeling Techniques in Loci-Stream using Axial Jet Pressure Control and Autogenous Pressurization Experiment

Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.

cryogenic fluid management↗