Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Multi-scale nonlinear stress analysis of Nb 3 Sn superconducting accelerator magnets

A multi-scale nonlinear procedure to analyze the stress in Nb 3 Sn superconducting accelerator magnets is presented to address one of the most challenging obstacles currently facing the successful development of high-field superconducting magnets—the issue of stress management. The study demonstrates that gaskets (special nonlinear materials) are capable of modeling the complex nonlinear deformation behavior of insulation layers within the Nb 3 Sn coil block and that Hill materials (orthotropic materials utilizing the Hill yield criterion) are suitable to enable homogenization of the filamentary regions and the resin-impregnated Nb 3 Sn Rutherford cables. With the whole magnet under preload, cool-down, and Lorentz forces, the nonlinear behavior of the Nb 3 Sn coil was simulated, in three orthongonal axes, by the combined properties of the gaskets (insulation layers) and Hill materials (resin-impreganted cable). The procedure entailes minimal material assumptions because it incorporated measured stress-strain curves in the analysis. The coil was simulated to a high level of detail consisting of the insulation layers and resin-impregnated cables. The computed compressive azimuthal stresses of the cables were used to assess the stress-induced performance degradation. Through submodeling, the area-weighted average axial strains of the strands were computed and employed to evaluate the strain-induced performance degradation. The overall performance degradation of the Nb 3 Sn coil was thus obtained, and this information was subsequently used to guide the design of the overall magnet. Besides Nb 3 Sn magnets, this procedure can also be employed in the design of LTS, HTS, and room temperature magnets or in any composite structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Structural and mechanical properties of monolayer amorphous carbon and boron nitride

Amorphous materials exhibit various characteristics that are not featured by crystals and can sometimes be tuned by their degree of disorder (DOD). Here, we report results on the mechanical properties of monolayer amorphous carbon (MAC) and monolayer amorphous boron nitride (maBN) with different DOD. The pertinent structures are obtained by kinetic-Monte-Carlo (kMC) simulations using machine-learning potentials (MLP) with density-functional-theory (DFT)-level accuracy. An intuitive order parameter, namely the areal fraction F x occupied by crystallites within the continuous random network, is proposed to describe the DOD. We find that F x captures the essence of the DOD: Samples with the same F x but different sizes and arrangements of crystallites, obtained using two distinct kMC procedures, have virtually identical radial distributions functions as well as bond-length and bond-angle distributions. Furthermore, by simulating the fracture process with molecular dynamics, we found that the mechanical responses of MAC and maBN before fracture are mainly determined by F x and are insensitive to the sizes and specific arrangements and to some extent the numbers and area distributions of the crystallites. The behavior of cracks in the two materials is analyzed and found to mainly propagate in meandering paths in the CRN region and to be influenced by crystallites in distinct ways that toughen the material. Furthermore, the present results reveal the relation between structure and mechanical properties in amorphous monolayers and may provide a universal toughening strategy for 2D materials.

2-dimensional systems↗
DOE OSTI2020

First Observation of Multiple Transverse Wobbling Bands of Different Kinds in 183 Au

Here, we report the first observation of two wobbling bands in 183 Au, both of which were interpreted as the transverse wobbling (TW) band but with different behavior of their wobbling energies as a function of spin. It increases (decreases) with spin for the positive (negative) parity configuration. The crucial evidence for the wobbling nature of the bands, dominance of the $\textit{E}$2 component in the Δ$\textit{I}$ = 1 transitions between the partner bands, is provided by the simultaneous measurements of directional correlation from the oriented states ratio and the linear polarization of the $\textit{γ}$ rays. Particle rotor model calculations with triaxial deformation reproduce the experimental data well. A value of spin, $I_m$, has been determined for the observed TW bands below which the wobbling energy increases and above which it decreases with spin. The nucleus 183 Au is, so far, the only nucleus in which both the increasing and the decreasing parts are observed and thus gives the experimental evidence of the complete transverse wobbling phenomenon.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Infinite Family of Integrable Sigma Models Using Auxiliary Fields

We introduce a class of 2D sigma models which are parametrized by a function of one variable. In addition to the physical field g , these models include an auxiliary field v α which mediates interactions in a prescribed way. We prove that every theory in this family is classically integrable, in that it possesses an infinite set of conserved charges in involution, which can be constructed from a Lax representation for the equations of motion. This class includes the principal chiral model (PCM) and all deformations of the PCM by functions of the energy-momentum tensor. Published by the American Physical Society 2024

Physics↗
DOE OSTI2023

Sequential flows by irrelevant operators

We explore whether one can T\overline{T} T T ¯ deform a collection of theories that are already T\overline{T} T T ¯ -deformed. This allows us to define classes of irrelevant deformations that know about subsystems. In some basic cases, we explore the spectrum that results from this procedure and we provide numerical evidence in favor of modular invariance. We also study the flow of the classical Lagrangian for free bosons and free fermions under successive deformations. Some of the models found by sequentially flowing are likely to have interesting holographic interpretations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Analysis of Microwave Resonant Cavity Transducer Degradation Mechanisms

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with the flat wall of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the resonant frequency, which can be detected with a spectrum analyzer. Because the transducer is intended for immersion in a high temperature corrosive fluid, understanding of material degradation is crucial for estimation of transducer performance lifetime, and development of measurement interpretation algorithms. We conducted a preliminary computational investigation of relevant damage mechanisms of a stainless steel 316 cylindrical resonator in FLiBe salt. The two main damage mechanisms, creep and corrosion, were modeled using multiphysics COMSOL software. Degradation was modeled for a temperature range 500°C to 700°C. Coupling of the damage mechanisms was not considered. These models predict significant inelastic deformation at most temperatures due to creep, and qualitatively predict chromium depletion both along the liquid/solid interface and along the grain boundaries. An algorithmic approach for compensation of these degradation effects during fluid flow measurements will be developed in the future work.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Second Annual Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with the flat wall of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the resonant frequency, which can be detected with a spectrum analyzer. Because the transducer is intended for immersion in a high temperature corrosive fluid, understanding of material degradation is crucial for estimation of transducer performance lifetime, and development of measurement interpretation algorithms. We conducted a preliminary computational investigation of relevant damage mechanisms of a stainless steel 316 cylindrical resonator in FLiBe salt. The two main damage mechanisms, creep and corrosion, were modeled using multiphysics COMSOL software. Degradation was modeled for a temperature range 500°C to 700°C. Coupling of the damage mechanisms was not considered. These models predict significant inelastic deformation at most temperatures due to creep, and qualitatively predict chromium depletion both along the liquid/solid interface and along the grain boundaries. An algorithmic approach for compensation of these degradation effects during fluid flow measurements will be developed in the future work. To validate sensor physics, we have performed proof-of-principle test of flow sensing in water. For this test, we have developed a cylindrical resonator for K-band, which was machined from brass. The cavity was excited through WR-42 waveguide through a subwavelength hole on the side of the wall of the cylinder. To increase the spectral signal visibility, we developed a signal processing method for baseline subtraction. A flow loop for proof-of-principle test of transducer performance in water was assembled. A commercial flow meter was installed in the loop for reference measurements. Cylindrical cavity was excited in the TE 011 mode with resonant frequency f ≈ 17.8GHz. Frequency shift of cavity spectral response was obtained by gradually increasing water flow rate from 0 to 60gpm. Corresponding monotonic increase of resonant frequency shift by several MHz was observed. Approximate figure of merit of sensitivity to flow rate is 100KHz/GPM. In addition, we have identified an existing liquid sodium experimental setup for demonstration of flow sensing in environment similar to that of an advanced reactor. The setup consists of a cylindrical vessel and center feed line, where transducer inserted through the lid will measure velocity of the impinging liquid jet. As a calibration experiment, we have assembled a water vessel with center feed with the same dimensions as those of the liquid sodium setup. We have also developed and insertion probe consisting of a 50cm brass waveguide enclosed in protective SS316 tube. Using the water loop, we have demonstrated feasibility of sensing the impinging liquid jet in the vessel.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

LDRD FY25 Program Overview

As Lawrence Livermore National Laboratory’s (LLNL’s) Laboratory Directed Research and Development (LDRD) program enters its fifth decade of leading-edge research and development, its impact and importance have never been stronger. The program continues to advance strategic investments in pioneering science, technology, and engineering, ensuring LLNL will be ready to deliver on our mission as it evolves over the coming decades. Investing in LDRD research, and the people who perform this critical work, gives LLNL the ability to sustain our role as a leader in the Department of Energy and National Nuclear Security Administration enterprise. The LDRD program enables high-risk, high-payoff research that anticipates emerging threats and future mission needs. By nurturing the ingenuity of the Lab’s greatest asset, its people, LDRD funding advances not only our research but also grows and nurtures our workforce: engaging future innovators with student mentoring, challenging postdoctoral researchers to apply their skills to support national security, and strengthening the leadership skills of early career staff. This annual report documents how LDRD investments advance LLNL’s science, technology, and engineering across our mission space. To assess LDRD’s impact we track both short and long-term metrics such as peer-reviewed publications, number of students, or professional fellows. In addition to reviewing these metrics, I encourage you to delve deeper into the breadth of science and technology that illustrate the strategic value of this research portfolio. For instance, a recent exploratory research project used advanced manufacturing to construct miniaturized three-dimensional ion traps for a quantum computer with reduced quantum error rates to enable applications that address national security missions and support basic science. Another project has delved into studying detonation by examining deflagration to enhance the safety and security of the nuclear weapons stockpile. LDRD researchers are also deploying AI agents on two of the world’s most powerful supercomputers to automate and accelerate inertial confinement fusion experiments. Other teams are delivering more accurate optical constants to enable improved validation for aluminum to advance atomic and molecular physics models. LDRD-driven discoveries of how metals deform under extreme conditions strengthen our ability to model and design materials for demanding national security environments. National security challenges are increasingly complex and continuously evolving. LDRD focuses our most innovative science and technology on these challenges, ensuring the Laboratory is developing creative, forward-leaning solutions for our nation and the world. The following pages feature highlights of published scientific advances, patents, and honors that stem from LDRD investments. As you read this report, I hope you will understand how these investments position the Laboratory, and our partners, to meet the demands of the decades ahead.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Coordinate transformation and truncation for rotating spacecraft with flexible appendages

The analytical structures of alternative coordinate transformations for the variables that characterize the deformations of finite element models of flexible appendages on rotating spacecraft are examined. Particular emphasis is given to the truncation operations that are essential for efficient numerical simulations of flexible spacecraft, due to the necessarily large number of coordinates employed in a finite element description. A theorem is developed which establishes necessary conditions for the commutativity of the required truncation and inversion operations. The recommended alternative for the rotating elastic appendage is a complex transformation with previously published orthogonality properties, which permit the derivation in this paper of a relatively simple explicit set of transformed and truncated equations of modal vibration in real variables.

Likins, P.↗
NASA NTRS1976

Dynamic response of membranes with finite elements

A general set of finite-element equations is developed for treating the nonlinear dynamic response of membranes consisting of complex nonlinear materials. The approach proposed by Key (1974) for a most complete treatment of the finite-element method to the nonlinear dynamic analysis of solids is used in developing the nonlinear equations of motion for membranes with cubic quadrilateral finite elements. The computations are kept general with respect to material modeling by computing the deformation gradient and requiring a constitutive subroutine to supply the Cauchy stress. An example calculation of the vibration of a square membrane demonstrates the accuracy of the formulation for small deformation theory and shows the nonlinear effect of large deformations.

Benzley, S. E.↗
NASA NTRS1978

The viscoelastic stiffness model of seismicity

A viscoelastic stiffness model of seismicity is developed by introducing a viscoelastic element into the stiffness model for fault dynamics. The introduction of this element permits modeling of transient anelastic deformations in response to stress loading and relaxation and provides a mechanism for partial stress recovery following an earthquake. As a consequence, several phenomena not present in elastic stiffness theory emerge. These include postseismic creep, foreshocks, and aftershocks. Numerical simulations of fault motion also reveal episodes of stable sliding, tertiary creep preceeding earthquakes, and long-term aseismic creep.

Cohen, S. C.↗
NASA NTRS1980

Analytic investigation of efficiency and performance limits in klystron amplifiers using multidimensional computer programs; multi-stage depressed collectors; and thermionic cathode life studies

Due to complexity of the program which used a hydrodynamic, axially and radially deformable disk-ring model and the resulting long computing time only the output gap was investigated. Results from independent studies were used to initiate the starting conditions for the electrons and the RF voltage using our program. Although this method of computation is less exact than processing the entire klystron interaction in 3-Dimensions it is shown that, for a confined flow focused throughout the penultimate cavity, radial velocities remain very small and the beam is highly laminar. It is concluded that possible errors resulting from treating only the output cavity in 3-D would remain small.

Kosmahl, H. G.↗
NASA NTRS1983

Prediction of impact force and duration during low velocity impact on circular composite laminates

Two simple and improved models--energy-balance and spring-mass--were developed to calculate impact force and duration during low velocity impact of circular composite plates. Both models include the contact deformation of the plate and the impactor as well as bending, transverse shear, and membrane deformations of the plate. The plate was transversely isotropic graphite/epoxy composite laminate and the impactor was a steel sphere. Calculated impact forces from the two analyses agreed with each other. The analyses were verified by comparing the results with reported test data.

Shivakumar, K. N.↗
NASA NTRS1985

Prediction of impact force and duration due to low-velocity impact on circular composite laminates

Two simple and improved models - energy-balance and spring-mass - were developed to calculate impact force and duration during low velocity impact of circular composite plates. Both models include the contact deformation of the plate and the impactor as well as bending, transverse shear, and membrane deformations of the plate. The plate was transversely isotropic graphite/epoxy composite laminate and the impactor was a steel sphere. Calculated impact forces from the two analyses agreed with each other. The analyses were verified by comparing the results with reported test data.

Shivakumar, K. N.↗
NASA NTRS1987

Empirical high-latitude electric field models

The present analysis of electric field measurements from the Dynamics Explorer 2 satellite, which extends previous empirical models, emcompasses much data from polar crossings entering and exiting the high latitudes in all magnetic local time zones. The goal is to represent the typical distributions of convective electric fields with a minimum number of characteristic patterns. Significant large-scale revisions of the OGO 6 dawn-dusk measurement models are made. The deformations of the two-cell patterns lead to sunward convection in dayside polar regions, while maintaining the integrity of the nightside convection pattern.

Heppner, J. P.↗
NASA NTRS1986

Finite element analysis of steady and transiently moving/rolling nonlinear viscoelastic structure. Part 1: Theory

In a three part series of papers, a generalized finite element analysis scheme is developed to handle the steady and transient response of moving/rolling nonlinear viscoelastic structure. This paper considers the development of the moving/rolling element strategy, including the effects of large deformation kinematics and viscoelasticity modelled by fractional integro-differential operators. To improve the solution strategy, a special hierarchical constraint procedure is developed for the case of steady rolling/translating as well as a transient scheme involving the use of a Grunwaldian representation of the fractional operator. In the second and third parts of the paper, 3-D extensions are developed along with transient contact strategies enabling the handling of impacts with obstructions. Overall, the various developments are benchmarked via comprehensive 2- and 3-D simulations. These are correlated with experimental data to define modelling capabilities.

Padovan, Joe↗