SEARCH · Engineering Papers

Results for “materials modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Accumulation of sedimentary debris in the south polar region of Mars and implications for climate history

A detailed modeling of the observed crater populations in stratigraphic unit mappings of the Martian south pole region is presently used to establish absolute constraints on the age of materials' emplacement. Modeling results indicate that cratered terrains poleward of 65 deg south latitude have subsequently experienced a steady-state net accumulation of materials at about 0.1 km/Ga; equatorial cratered terrains have by contrast retained a virtually pristine form.

Plaut, J. J.↗

NASA NTRS1973

Finite element analysis of a composite material interface

A finite element model of a composite material interface is developed to study the influence of the interface on the thermal strain in the composite. A plane stress model is used with an axisymmetric model as a check. The interface thickness, thermal coefficient, modulus, Poisson's ratio and the percent of mineral in the composite are variables in the study. The results confirmed the usability of the finite element model in studying the polymer-mineral interface.

Murray, K. H.↗

NASA NTRS1995

Effect of various approximations on predicted progressive failure in plain weave composites

Three-dimensional finite element analysis was used to simulate progressive failure of a plain weave composite subjected to in-plane extension. The loading was parallel to one of the tow directions. The effects of various characteristics of the finite element model on predicted behavior were examined. The predicted behavior was found to be sensitive to quadrature order, mesh refinement, and the material degradation model. Also the sensitivity of the predictions to the tow waviness was studied. The predicted strength decreased considerably with increased waviness. More numerical studies and comparisons with experimental data are needed to establish reliable guidelines for accurate progressive failure prediction.

Whitcomb, John↗

NASA NTRSDate not supplied

Analysis of Pyrolysis Products from Ablative Thermal Protection Systems

NASA’s state-of-the-art ablative materials are composed of a three-dimensional network of carbon fibers impregnated with polymers that dissipate thermal energy through pyrolysis. A fundamental understanding of the decomposition mechanisms and pyrolysis product distributions of various classes of polymers is instrumental in the design of new ablative materials. Furthermore, innovative experiments are essential to the continuous modernization of material response models by providing high-fidelity data. Thus, an apparatus has been designed to measure pyrolysis products from polymers and composite materials by implementing in-situ mass spectrometric techniques. Initial results from experiments performed on siloxane resins and a common phenolic resin will be discussed. Both classes of polymers exhibit heating-rate-dependent decomposition mechanisms. At the onset of heating, phenolic polymers decompose through competitive reactions to form gaseous products and a carbonaceous char. Gas phase products of phenolic resins are typically composed of molecular hydrogen, water, and aromatic hydrocarbons. Pyrolysis products from siloxane polymers include molecular hydrogen, small molecules, and cyclic oligomers from the polymer backbone.

Pyrolysis↗

NASA NTRSDate not supplied

Analysis of Pyrolysis Products from Ablative TPS

Pyrolysis↗

NASA NTRS1977

Charging characteristics of materials: Comparison of experimental results with simple analytical models

An understanding of the behavior of materials, of dielectrics in particular, under charged particle bombardment is essential to the prediction and prevention of the adverse effects of spacecraft charging. A one-dimensional model for charging of samples in a test facility was used in conjunction with experimental data taken to develop "material charging characteristics" for silvered Teflon. These characteristics were then used in a one-dimensional model for charging in space to examine expected response. Relative charging rates as well as relative charging levels for silvered Teflon and metal are discussed.

Purvis, C. K.↗

NASA NTRS1992

Composite-Blade Structural Analyzer

COBSTRAN (COmposite Blade STRuctural ANalyzer) computer program is preprocessor and postprocessor facilitating design and analysis of composite turbofan and turboprop blades, and of composite wind-turbine blades. Combines theories of mechanics of composites and of laminates with data base of fiber and matrix properties. Designed to carry out linear analyses required for efficient mathematical modeling and analysis of bladelike structural components made of multilayered angle-plied fiber composites. Components made from isotropic or anisotropic homogeneous materials also modeled. Written in FORTRAN 77.

Aiello, R. A.↗

NASA NTRS2011

Ndarts

Ndarts software provides algorithms for computing quantities associated with the dynamics of articulated, rigid-link, multibody systems. It is designed as a general-purpose dynamics library that can be used for the modeling of robotic platforms, space vehicles, molecular dynamics, and other such applications. The architecture and algorithms in Ndarts are based on the Spatial Operator Algebra (SOA) theory for computational multibody and robot dynamics developed at JPL. It uses minimal, internal coordinate models. The algorithms are low-order, recursive scatter/ gather algorithms. In comparison with the earlier Darts++ software, this version has a more general and cleaner design needed to support a larger class of computational dynamics needs. It includes a frames infrastructure, allows algorithms to operate on subgraphs of the system, and implements lazy and deferred computation for better efficiency. Dynamics modeling modules such as Ndarts are core building blocks of control and simulation software for space, robotic, mechanism, bio-molecular, and material systems modeling.

Jain, Abhinandan↗

NASA NTRS2021

Analysis of Arc Welding Process in Space

This work is motivated by NASA plans to conduct welding experiments on the ISS. It is expected that deployment of welding and additive manufacturing technologies in the space environment has the potential to revolutionise how orbiting platforms are designed, manufactured, and assembled. However, the structure, composition and quality of a weld is extremely dependent on the environment and can be difficult to control in space. Shielding gases would also be tough to manage as gases behave differently in zero gravity and airless environments. Additional points of concern are related to the spatter and sparks dynamics in space. Therefore, there is a need for a more basic understanding of welding processes by computational modelling. To provide such an insight we developed state of art models of the ARC torch, droplet detachment and transfer, and the melt pool build up using magnetohydrodynamics approximation and level set method for two-phase liquid metal/-gas flow modelling. Two finite element models were built using 2D axisymmetric geometry in COMSOL Multiphysics®: (i) stationary model of the ARC torch and (ii) dynamical model of droplet detachment and transfer. Both models demonstrate reasonable agreement with earlier experimental observations and high sensitivity to the temperature dependence of the thermophysical parameters on the system materials. The models were used to provide physical insight into ARC welding in various environments and geometries. It was shown, in particular, that there is a significant probability of gas bubbles trapping in the meltpool and a possibility of unbounded wondering of sparks in the welding chamber in zero gravity. In addition, we estimated metal evaporation rate that may be hazardous in the confined environment of the ISS. These issues raise concern of quality of the weld and safety for ISS applications.

ARC welding↗

NASA NTRS1989

Five year ground exposure of composite materials used on the Bell Model 206L flight service evaluation

Part of the results of a U.S. Army/NASA-Langley sponsored research program to establish the long term-term effects of realistic ground based exposure on advanced composite materials is presented. Residual strengths and moisture absorption as a function of exposure time and exposure location are reported for four different composite material systems that were exposed for five years on the North American Continent.

Baker, Donald J.↗

NASA NTRS1973

Three models of the vibrating ulna.

Evaluation of the ability of three models of the ulna to predict ulnar resonant frequency. The ulna is considered to be a uniform cylindrical tube made of homogeneous isotropic material. In model I the tube is attached at each end to rigid supports by hinges, in model II the tube is attached to rigid supports by springs rather than hinges, while model III is the same as model II except for the addition of a spring-mass system simulating an accelerometer strapped to the wrist. It is found that all three models exhibit comparable effectiveness in predicting the allowed cyclic vibration frequency, although model I is marginally better than models II or III in predicting this parameter. All three models also yield relatively realistic values for Young's modulus. In terms of results, therefore, there is no clear choice between the models. However, owing to greater costs incurred with models II and III, it is concluded that model I is the most useful, even though it is the least 'realistic' of the three models evaluated.-

Jurist, J. M.↗

NASA NTRS1992

Superplastic forming of ceramic insulation

Superplasticity has been demonstrated in many fine-grained structural ceramics and ceramic composites, including yttria-stabilized tetragonal zirconia polycrystal (YTZP), alumina, and Al2O3-reinforced zirconia (Al2O3/YTZ) duplex composites and SiC-reinforced Si3N4. These superplastic ceramics obviously offer the potential benefit of forming net shape or near net shape parts. This could be particularly useful for forming complicated shapes that are difficult to achieve using conventional forming techniques, or require elaborate, subsequent machining. In the present study, we successfully demonstrated the following: (1) superplastic 3Y-TXP and 20 percent Al2O3/YTZ composite have for the first time been successfully deformed into hemispherical caps via a biaxial gas-pressure forming technique; (2) no experimental difficulty was encountered in applying the required gas pressures and temperatures to achieve the results, thus, it is certain that higher rates of deformation than those presented in this study will be possible by using the current test apparatus at higher temperatures and pressures; and (3) an analytical model incorporating material parameters, such as variations during forming in the strain rate sensitivity exponent and grain growth-induced strain hardening, is needed to model accurately and therefore precisely control the biaxial gas-pressure forming of superplastic ceramics. Based on the results of this study, we propose to fabricate zirconia insulation tubes by superplastic extrusion of zirconia polycrystal. This would not only reduce the cost, but also improve the reliability of the tube products.

Nieh, T. G.↗

NASA NTRS1993

Test model designs for advanced refractory ceramic materials

The next generation of space vehicles will be subjected to severe aerothermal loads and will require an improved thermal protection system (TPS) and other advanced vehicle components. In order to ensure the satisfactory performance system (TPS) and other advanced vehicle materials and components, testing is to be performed in environments similar to space flight. The design and fabrication of the test models should be fairly simple but still accomplish test objectives. In the Advanced Refractory Ceramic Materials test series, the models and model holders will need to withstand the required heat fluxes of 340 to 817 W/sq cm or surface temperatures in the range of 2700 K to 3000 K. The model holders should provide one dimensional (1-D) heat transfer to the samples and the appropriate flow field without compromising the primary test objectives. The optical properties such as the effective emissivity, catalytic efficiency coefficients, thermal properties, and mass loss measurements are also taken into consideration in the design process. Therefore, it is the intent of this paper to demonstrate the design schemes for different models and model holders that would accommodate these test requirements and ensure the safe operation in a typical arc jet facility.

Tran, Huy Kim↗

NASA NTRS1989

Extension-torsion coupling behavior of advanced composite tilt-rotor blades

An analytic model was developed to study the extension-bend-twist coupling behavior of an advanced composite helicopter or tilt-rotor blade. The outer surface of the blade is defined by rotating an arbitrary cross section about an initial twist axis. The cross section can be nonhomogeneous and composed of generally anisotropic materials. The model is developed based upon a three dimensional elasticity approach that is recast as a coupled two-dimensional boundary value problem defined in a curvilinear coordinate system. Displacement solutions are written in terms of known functions that represent extension, bending, and twisting and unknown functions for local cross section deformations. The unknown local deformation functions are determined by applying the principle of minimum potential energy to the discretized two-dimensional cross section. This is an application of the Ritz method, where the trial function family is the displacement field associated with a finite element (8-node isoparametric quadrilaterals) representation of the section. A computer program was written where the cross section is discretized into 8-node quadrilateral subregions. Initially the program was verified using previously published results (both three-dimensional elasticity and technical beam theory) for pretwisted isotropic bars with an elliptical cross section. In addition, solid and thin-wall multi-cell NACA-0012 airfoil sections were analyzed to illustrate the pronounced effects that pretwist, initial twist axis location, and spar location has on coupled behavior. Currently, a series of advanced composite airfoils are being modeled in order to assess how the use of laminated composite materials interacts with pretwist to alter the coupling behavior of the blade. These studies will investigate the use of different ply angle orientations and the use of symmetric versus unsymmetric laminates.

Kosmatka, J. B.↗

NASA NTRS1985

Degradation studies of SMRM Teflon

A working group was organized to study materials and components of the Solar Max Satellite (SMS) that was returned by the STS 41C. These materials were exposed in space for 50 months and represent the only real time long term exposure data available to date. In the molecular modeling of material and energetic oxygen atom interaction, it is pointed out that the importance of developing correlation between accelerated exposure data from STS and some real time data. In particular, it was predicted that Teflon which showed no detectable degradation on various STS flights may be susceptible to atomic oxygen degradation under real time conditions. Initial inspection of returned SMS samples showed that Teflon suffered visual damage such as cracking and yellowing. The results of examination of these samples are given.

Liang, R. H.↗

NASA NTRS1992

Development of 3D electromagnetic modeling tools for airborne vehicles

The main goal of this project is to develop methodologies for scattering by airborne composite vehicles. Although our primary focus continues to be the development of a general purpose code for analyzing the entire structure as a single unit, a number of other tasks are also pursued in parallel with this effort. These tasks are important in testing the overall approach and in developing suitable models for materials coatings, junctions and, more generally, in assessing the effectiveness of the various parts comprising the final code. Here, we briefly discuss our progress on the five different tasks which were pursued during this period. Our progress on each of these tasks is described in the detailed reports (listed at the end of this report) and the memoranda included. The first task described below is, of course, the core of this project and deals with the development of the overall code. Undoubtedly, it is the outcome of the research which was funded by NASA-Ames and the Navy over the past three years. During this year we developed the first finite element code for scattering by structures of arbitrary shape and composition. The code employs a new absorbing boundary condition which allows termination of the finite element mesh only 0.3 lambda from the outer surface of the target. This leads to a remarkable reduction of the mesh size and is a unique feature of the code. Other unique features of this code include capabilities to model resistive sheets, impedance sheets and anisotropic materials. This last capability is the latest feature of the code and is still under development. The code has been extensively validated for a number of composite geometries and some examples are given. The validation of the code is still in progress for anisotropic and larger non-metallic geometries and cavities. The developed finite element code is based on a Galerkin's formulation and employs edge-based tetrahedral elements for discretizing the dielectric sections and the region between the target and the outer mesh termination boundary (ATB). This boundary is placed in conformity with the target's outer surface, thus resulting in additional reduction of the unknown count.

Volakis, John L.↗

NASA NTRSDate not supplied

Analysis of Mars 2020 Entry with Coupled Material Response and CFD

When computing the response of an ablating thermal protection system during entry, the aerothermal environment and material response are traditionally computed independently, with the introduction of a blowing correction term in the material response model to account for the outgassing of char and pyrolysis gases. This study presents an approach, where the pyrolysis blowing gases, calculated within the PATO material response code [1], are integrated into the DPLR hypersonic CFD code [2] via a blowing boundary condition. This methodology employs an iterative process, whereby the blown pyrolysis gas products from PATO are incorporated into DPLR, refining surface heating predictions. The NEQAIR code is used to compute radiative heating [3]. The method is applied in computing 3D material response of the Mars 2020 entry. When compared with uncoupled material response, the coupled simulations show a lower surface heat flux initially and a higher heat flux at peak heating as shown in Fig. 1. This is in agreement with previous work using a sphere case with environments from MSL [4].

Heat Transfer↗

NASA NTRSDate not supplied

Analysis of Mars 2020 Entry with Coupled Material Response and CFD

When computing the response of an ablating thermal protection system during entry, the aerothermal environment and material response are traditionally computed independently, with the introduction of a blowing correction term in the material response model to account for the outgassing of char and pyrolysis gases. This study presents an approach, where the pyrolysis blowing gases, calculated within the PATO material response code, are integrated into the DPLR hypersonic CFD code via a blowing boundary condition. This methodology employs an iterative process, whereby the blown pyrolysis gas products from PATO are incorporated into DPLR, refining surface heating predictions. The NEQAIR code is used to compute radiative heating. The method is applied in computing 3D material response of the Mars 2020 entry. When compared with uncoupled material response, the coupled simulations show a lower surface heat flux initially and a higher heat flux at peak heating as shown in Fig. 1. This is in agreement with previous work using a sphere case with environments from MSL.

Heat Transfer↗