Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “local density approximations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Effects of Heating Configuration and Operating Parameters on Heat Transfer and Interfacial Physics of Microgravity Flow Boiling With Subcooled Inlet Conditions –Experiments Onboard the International Space Station

This study is part of the Flow Boiling and Condensation Experiment (FBCE), a collaborative effort between the Purdue University Boiling and Two-Phase Flow Laboratory (PU-BTPFL) and the NASA Glenn Research Center. The FBCE fitted with the Flow Boiling Module (FBM) was launched to the International Space Station (ISS) in August 2021 and experiments were successfully performed from February to July 2022 to amass a large microgravity-flow-boiling database. This study is focused on heat transfer and flow visualization of microgravity flow boiling of n-Perfluorohexane in a rectangular channel of 5.0 mm height, 2.5 mm width (heated), and 114.6 mm length, with subcooled inlet conditions. High-speed-video photography is utilized to present flow patterns and temporal interfacial behavior. Heat transfer results are presented in the form of flow boiling curves and both parametric curves and streamwise profiles of wall temperature and heat transfer coefficient. Firstly, the parametric effects of mass velocity (199.4 – 3200.0 kg/m 2 s), inlet subcooling (0.2 – 46.0°C), and inlet pressure (124.2 – 176.7 kPa), on the aforementioned aspects are assessed for double-sided heating to establish them for a microgravity environment. Of these three parameters, mass velocity and inlet subcooling mostly determine the microgravity flow boiling behavior, while inlet pressure plays an insignificant role. Flow patterns for double-sided heating are more complex than those for single-sided heating due to interaction between the two vapor layers. Vapor interaction is minimized at high subcoolings and high mass velocities due to strong condensation offered by the subcooled bulk liquid layer separating them. Despite the different flow patterns, both single- and double-sided heating generally result in similar parametric trends and local heat transfer coefficients for similar operating conditions. Flow instabilities manifest as temporal flow anomalies and temperature oscillations, and their severity increases with increasing boiling number. Secondly, the effects of heating configuration are analyzed by comparing and contrasting several aspects of single- and double-sided heating data. The heat fluxes at which onset of nucleate boiling degradation (ONBD) and critical heat flux (CHF) occur are distinctly different for single- and double-sided heating. There exists a threshold inlet subcooling demarcating the dominance of flow acceleration and condensation effects in vapor removal from the near-wall region and replenishment of fresh liquid for boiling. Above the threshold, condensation from the near-wall region is dominant and single-sided heating yields higher heat fluxes, and below it, acceleration is dominant and double-sided yields higher heat fluxes. At mass velocity in the range of 200 – 2400 kg/m 2 s, the threshold inlet subcooling lies in the approximate range of 20 – 30°C (corresponding inlet quality of roughly -0.40 – -0.20).

Microgravity↗
DOE OSTI2022

Nonequilibrium DMFT + CPA for correlated disordered systems

We present a solution for the nonequilibrium dynamics of an interacting disordered system. The approach adapts the combination of the equilibrium dynamical mean-field theory and the equilibrium coherent potential approximation methods to the nonequilibrium many-body formalism, using the Kadanoff-Baym-Keldysh complex time contour, for the dynamics of interacting disordered systems away from equilibrium. We use our time domain solution to obtain the equilibrium density of states of the disordered interacting system described by the Anderson-Hubbard model, bypassing the necessity for the cumbersome analytical continuation process. We further apply the nonequilibrium solution to the interaction quench problem for an isolated disordered system. Here, the interaction is abruptly changed from zero (noninteracting system) to another constant (finite) value at which it is subsequently kept. We observe via the time dependence of the potential, kinetic, and total energies the effect of disorder on the relaxation of the system as a function of final interaction strength. Finally, the real-time approach has the potential to shed light on the fundamental role of disorder in the nonequilibrium dynamics of interacting quantum systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2000

Hierarchical Statistical 3D ' Atomistic' Simulation of Decanano MOSFETs: Drift-Diffusion, Hydrodynamic and Quantum Mechanical Approaches

When MOSFETs are scaled to deep submicron dimensions the discreteness and randomness of the dopant charges in the channel region introduces significant fluctuations in the device characteristics. This effect, predicted 20 year ago, has been confirmed experimentally and in simulation studies. The impact of the fluctuations on the functionality, yield, and reliability of the corresponding systems shifts the paradigm of the numerical device simulation. It becomes insufficient to simulate only one device representing one macroscopical design in a continuous charge approximation. An ensemble of macroscopically identical but microscopically different devices has to be characterized by simulation of statistically significant samples. The aims of the numerical simulations shift from predicting the characteristics of a single device with continuous doping towards estimating the mean values and the standard deviations of basic design parameters such as threshold voltage, subthreshold slope, transconductance, drive current, etc. for the whole ensemble of 'atomistically' different devices in the system. It has to be pointed out that even the mean values obtained from 'atomistic' simulations are not identical to the values obtained from continuous doping simulations. In this paper we present a hierarchical approach to the 'atomistic' simulation of aggressively scaled decanano MOSFETs. A full scale 3D drift-diffusion'atomostic' simulation approach is first described and used for verification of the more economical, but also more restricted, options. To reduce the processor time and memory requirements at high drain voltage we have developed a self-consistent option based on a thin slab solution of the current continuity equation only in the channel region. This is coupled to the Poisson's equation solution in the whole simulation domain in the Gummel iteration cycles. The accuracy of this approach is investigated in comparison with the full self-consistent solution. At low drain voltage only single solution of the nonlinear Poisson equation is sufficient to extract the current with satisfactory accuracy. A pilot version of a hydrodynamic 'atomistic' simulator has been developed in order to study the effect of the nonequilibrium, non local transport in decanano MOSFETs on the random dopant induced current fluctuations. For the first time we have also applied the density gradient approach in 3D to investigate the effect of the quantum confinement on the threshold voltage fluctuations. The developed 'atomistic' simulation techniques have been applied to study various fluctuation resistant MOSFET architectures including epitaxial and delta doped devices.

Asenov, Asen↗
NASA NTRS1994

Steps toward determination of the size and structure of the broad-line region in active galactic nuclei. 5: Variability of the ultraviolet continuum and emission lines of NGC 3783

We report on the results of intensive ultraviolet spectral monitoring of the Seyfert 1 galaxy NGC 3783. The nucleus of NGC 3783 was observed with the International Ultraviolet Explorer satellite on a regular basis for a total of 7 months, once every 4 days for the first 172 days and once every other day for the final 50 days. Significant variability was observed in both continuum and emission-line fluxes. The light curves for the continuum fluxes exhibited two well-defined local minima or 'dips,' the first lasting is less than or approximately 20 days and the second is less than or approximately 4 days, with additional episodes of relatively rapid flickering of approximately the same amplitude. As in the case of NGC 5548 (the only other Seyfert galaxy that has been the subject of such an intensive, sustained monitoring effort), the largest continuum variations were seen at the shortest wavelengths, so that the continuum became 'harder' when brighter. The variations in the continuum occurred simultaneously at all wavelengths (delta(t) is less than 2 days). Generally, the amplitude of variability of the emission lines was lower than (or comparable to) that of the continuum. Apart from Mg II (which varied little) and N V (which is relatively weak and badly blended with Ly(alpha), the light curves of the emission lines are very similar to the continuum light curves, in each case with a small systematic delay or 'lag.' As for NGC 5548, the highest ionization lines seem to respond with shorter lags than the lower ionization lines. The lags found for NGC 3783 are considerably shorter than those obtained for NGC 5548, with values of (formally) approximately 0 days for He II + O III), and approximately 4 days for Ly(alpha) and C IV. The data further suggest lags of approximately 4 days for Si IV + O IV) and 8-30 days for Si III + C III). Mg II lagged the 1460 A continuum by approximately 9 days, although this result depends on the method of measuring the line flux and may in fact be due to variability of the underlying Fe II lines. Correlation analysis further shows that the power density spectrum contains substantial unresolved power over timescales of is less than or approximately 2 days, and that the character of the continuum variability may change with time.

Reichert, G. A.↗
DOE OSTI2021

Toward a First-Principles Framework for Predicting Collective Properties of Electrolytes

Conspectus Given the universal importance of electrolyte solutions, it is natural to expect that we have a nearly complete understanding of the fundamental properties of these solutions (e.g., the chemical potential) and that we can therefore explain, predict, and control the phenomena occurring in them. In fact, reality falls short of these expectations. But, recent advances in the simulation and modeling of electrolyte solutions indicate that it should soon be possible to make progress toward these goals. In this Account, we will discuss the use of first-principles interaction potentials based in quantum mechanics (QM) to enhance our understanding of electrolyte solutions. Specifically, we will focus on the use of quantum density functional theory (DFT) combined with molecular dynamics simulation (DFT-MD) as the foundation for our approach. The overarching concept is to understand and accurately reproduce the balance between local or short-ranged (SR) structural details and long-range (LR) correlations, allowing the prediction of the thermodynamics of both single ions in solution as well as the collective interactions characterized by activity/osmotic coefficients. In doing so, relevant collective motions and driving forces characterized by chemical potentials can be determined. Here, in this Account, we will make the case that understanding electrolyte solutions requires a faithful QM representation of the SR nature of the ion–ion, ion–water, and water–water interactions. However, the number of molecules that is required for collective behavior makes the direct application of high-level QM methods that contain the best SR physics untenable, making methods that balance accuracy and efficiency a practical goal. Alternatives such as continuum solvent models (CSMs) and empirically based classical molecular dynamics have been extensively employed to resolve this problem but without yet overcoming the fundamental issue of SR accuracy. We will demonstrate that accurately describing the SR interaction is imperative for predicting both intrinsic properties, namely, at infinite dilution, and collective properties of electrolyte solutions. DFT has played an important role in our understanding of condensed phase systems, e.g., bulk liquid water, the air–water interface, ions in bulk, and at the air–water interface. This approach holds huge promise to provide benchmark calculations of electrolyte solution properties that will allow for the development and improvement of more efficient methods, as well as an enhanced understanding of fundamental phenomena. However, the standard protocol using the generalized gradient approximation with van der Waals (vdW) correction requires improvement in order to achieve a high level of quantitative accuracy. Simply simulating with higher level DFT functionals may not be the best route considering the significant computational cost. Alternative methods of incorporating information from higher levels of QM should be explored; e.g., using force matching techniques on small clusters, where high level benchmark calculations are possible, to develop ideal correction terms to the DFT functional is a promising possibility. We argue that DFT with statistical mechanics is becoming an increasingly useful framework enabling the prediction of collective electrolyte properties.

Duignan, Timothy T.↗
NASA NTRS2002

Simulations of Ground and Space-Based Oxygen Atom Experiments

Fast, pulsed atomic oxygen sources are a key tool in ground-based investigations of spacecraft contamination and surface erosion effects. These technically challenging ground-based studies provide a before and after picture of materials under low-earth-orbit (LEO) conditions. It would be of great interest to track in real time the pulsed flux from the source to the surface sample target and beyond in order to characterize the population of atoms and molecules that actually impact the surface and those that make it downstream to any coincident detectors. We have performed simulations in order to provide such detailed descriptions of these ground-based measurements and to provide an assessment of their correspondence to the actual LEO environment. Where possible we also make comparisons to measured fluxes and erosion yields. To perform the calculations we use a detailed description of a measurement beam and surface geometry based on the W, pulsed apparatus at Montana State University. In this system, a short pulse (on the order of 10 microseconds) of an O/O2 beam impacts a flat sample about 40 cm downstream and slightly displaced &om the beam s central axis. Past this target, at the end of the beam axis is a quadrupole mass spectrometer that measures the relative in situ flux of 0102 to give an overall normalized erosion yield. In our simulations we use the Direct Simulation Monte Carlo (DSMC) method, and track individual atoms within the atomic oxygen pulse. DSMC techniques are typically used to model rarefied (few collision) gas-flows which occur at altitudes above approximately 110 kilometers. These techniques are well suited for the conditions here, and multi-collision effects that can only be treated by this or a similar technique are included. This simulation includes collisions with the surface and among gas atoms that have scattered from the surface. The simulation also includes descriptions of the velocity spread and spatial profiles of the O/O2 beam obtained from separate measurements. These computations use basic engineering models for the gas-gas and gas-surface scattering and focus on the influence of multi-collision effects. These simulations characterize many important quantities of interest including the actual flux of atoms that reach the surface, the energy distribution of this flux, as well as the direction of the velocity of the flux that strikes the surface. These quantities are important in characterizing the conditions which give rise to measured surface erosion. The calculations also yield time- snapshots of the pulse as it impacts and flows around the surface. These snapshots reveal the local environment of gas near the surface for the duration of the pulse. We are also able to compute the flux of molecules that travel downstream and reach the spectrometer, and we characterize their velocity distribution. The number of atoms that reach the spectrometer can in fact be influenced by the presence of the surface due to gas-gas collisions from atoms scattered h m the surface, and it will generally be less than that with the surface absent. This amounts to an overall normalization factor in computing erosion yields. We discuss these quantities and their relationship to the gas-surf$ce interaction parameters. We have also performed similar calculations corresponding to conditions (number densities, temperatures, and velocities) of low-earth orbit. The steady-state nature and lower overall flux of the actual space environment give rise to differences in the nature of the gas-impacts on the surface from those of the ground-based measurements using a pulsed source.

Minton, T. K.↗
DOE OSTI2021

Probabilistic simulation of quantum circuits using a deep-learning architecture

The fundamental question of how to best simulate quantum systems using conventional computational resources lies at the forefront of condensed matter and quantum computation. It impacts both our understanding of quantum materials and our ability to emulate quantum circuits. Here we present an exact formulation of quantum dynamics via factorized generalized measurements which maps quantum states to probability distributions with the advantage that local unitary dynamics and quantum channels map to local quasistochastic matrices. This representation provides a general framework for using state-of-the-art probabilistic models in machine learning for the simulation of quantum many-body dynamics. Using this framework, we have developed a practical algorithm to simulate quantum circuits using an attention network based on a powerful neural network ansatz responsible for the most recent breakthroughs in natural language processing. We demonstrate our approach by simulating circuits that build Greenberger-Horne-Zeilinger and linear graph states of up to 60 qubits, as well as a variational quantum eigensolver circuit for preparing the ground state of the transverse field Ising model on several system sizes. Our methodology constitutes a modern machine learning approach to the simulation of quantum physics with applicability both to quantum circuits as well as other quantum many-body systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2013

NIR Imaging Spectroscopy of the Inner Few Arcseconds of NGC 4151 with OSIRIS at Keck

We present H- and K-band data from the inner arcsecond of the Seyfert 1.5 galaxy NGC 4151 obtained with the adaptive optics assisted near-infrared imaging field spectrograph OSIRIS at the Keck Observatory. The angular resolution is about a few parsecs on-site and thus competes easily with optical images taken previously with the Hubble Space Telescope. We present the morphology and dynamics of most species detected but focus on the morphology and dynamics of the narrow line region (as traced by emission of [FeII]λ1.644 μm), the interplay between plasma ejected from the nucleus (as traced by 21 cm continuum radio data) and hot H2 gas and characterize the detected nuclear HeIλ2.058 μm absorption feature as a narrow absorption line (NAL) phenomenon. Emission from the narrow line region (NLR) as traced by [FeII] reveals a biconical morphology and we compare the measured dynamics in the [FeII] emission line with models proposing acceleration of gas in the NLR and simple ejection of gas into the NLR. In the inner 2.5 arcseconds the acceleration model reveals a better fit to our data than the ejection model.We also see evidence that the jet very locally enhances emission in [FeII] at certain positions in our field-of-view such that we were able to distinct the kinematics of these clouds from clouds generally accelerated in the NLR. Further, the radio jet is aligned with the bicone surface rather than the bicone axis such that we assume that the jet is not the dominant mechanism responsible for driving the kinematics of clouds in the NLR. The hot H2 gas is thermal with a temperature of about 1700 K. We observe a remarkable correlation between individual H2 clouds at systemic velocity with the 21 cm continuum radio jet. We propose that the radio jet is at least partially embedded in the galactic disk of NGC 4151 such that deviations from a linear radio structure are invoked by interactions of jet plasma with H2 clouds that are moving into the path of the jet because of rotation of the galactic disk of NGC 4151. Additionally, we observe a correlation of the jet as traced by the radio data, with gas as traced in Brγ and H2, at velocities between systemic and +/- 200 km/s at several locations along the path of the jet. The HeIλ2.058 μm line in NGC 4151 appears in emission with a blueshifted absorption component from an outflow. The emission (absorption) component has a velocity offset of 10 km/s (-280 km/s) with a Gaussian (Lorentzian) full-width (half-width) at half maximum of 160 km/s (440 km/s). The absorption component remains spatially unresolved and its kinematic measures differ from that of UV resonance absorption lines. From the amount of absorption we derive a lower limit of the HeI 2S column density of 1 × 10(exp 14) cm−2 with a covering factor along the line-of-sight of C(sub los) approximately equal to 0.1.

K-band data↗
DOE OSTI2022

Death at watersheds: Galaxy quenching in low-density environments

The evolution of galaxies is influenced by their local and global environment in the cosmic web. Galaxies with very old stellar populations (VO galaxies with D n (4000) index ≥1.75) mostly lie in the centres of galaxy clusters, where they evolve under the influence of processes characteristic of high-density cluster environments. However, VO galaxies have also been found in poor groups in global low-density environments between superclusters, which we call watershed regions. Our aim is to analyse the properties of galaxies in various cosmic environments with a focus on VO galaxies in the watershed regions to understand their evolution, and the origin of the large-scale morphology–density relation. We employ the Sloan Digital Sky Survey DR10 MAIN spectroscopic galaxy sample in the redshift range 0.009 ≤ z ≤ 0.200 to calculate the luminosity–density field of galaxies, to determine groups and filaments in the galaxy distribution, and to obtain data on galaxy properties. The luminosity–density field with smoothing length 8 h -1 Mpc, D8, characterises the global environment of galaxies. We analyse the group and galaxy contents of regions with various D8 thresholds. We divide groups into low- and high-luminosity groups based on the highest luminosity of groups in the watershed region, L gr ≤ 15 × 10 12 h -2 L ⊙ . We compare the stellar masses, the concentration index, and the stellar velocity dispersions of quenched and star-forming galaxies among single galaxies, satellite galaxies, and the brightest group galaxies (BGGs) in various environments. We show that the global density is most strongly related to the richness of galaxy groups. Its influence on the overall star formation quenching in galaxies is less strong. Correlations between the morphological properties of galaxies and the global density field are the weakest. The watershed regions with D8 < 1 are populated mostly by single galaxies, constituting 70% of all galaxies there, and by low-luminosity groups. Still, approximately one-third of all galaxies in the watershed regions are VO galaxies. They have lower stellar masses, smaller stellar velocity dispersions, and stellar populations that are up to 2 Gyr younger than those of VO galaxies in other global environments. In higher density global environments (D8 > 1), the morphological properties of galaxies are very similar. Differences in galaxy properties are the largest between satellites and BGGs in groups. Our results suggest that galaxy evolution is determined by the birthplace of galaxies in the cosmic web, and mainly by internal processes which lead to the present-day properties of galaxies. This may explain the similarity of (VO) galaxies in extremely different environments.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRSDate not supplied

Effect of Vacuum on Force Response of an Ultrasonic Penetrator

Introduction: The Apollo astronauts encountered higher than expected resistances when interacting with the lunar soil via the Apollo Lunar Surface Drill (ALSD) and the trenching tool. Reducing the force required to move tools or other mechanical components through regolith will impact many steps of the resource extraction process. Force reduction has been achieved in soil materials by imparting vibration to tooling interfaces such as a vibratory farming cultivator, a percussive scoop, and ultrasonically resonant penetrators. Vibration-assisted tools in granular media reduce interaction forces by fluidizing a volume around the tool, allowing the tool to progress through a dynamic (fluid) medium instead of a static (solid) medium. This work seeks to quantify ultrasonic vibration’s effect on the force response of a penetrator in lunar soil simulant in vacuum sufficient to be within the molecular flow regime of any disturbed gases. Methods: A custom vacuum chamber setup, CUBEvac, was designed and built to facilitate penetration testing in a high vacuum environment, for comparison to penetration behavior in ambient terrestrial environment. A two-stage pumping system (Agilent Triscroll 600 roughing pump, Agilent VHS-6 oil diffusion pump) reached chamber pressures of about 5x10-6 Torr with regolith simulant in place. Figure 1 is a schematic of the heart of the assembly (note the penetration drive mechanisms above the chamber feedthrough and the regolith simulant sample in the bottom are not shown). The penetration actuation stack was comprised of a stepper motor driving a lead screw to move the ultra-sonic probe vertically inside the chamber. Motion was coordinated with an Arduino Uno. GRC-3 lunar simulant was used for this set of experiments. Samples were prepared in a four-liter stain-less steel, cylindrical pot with an internal diameter of approximately 15.56 cm (6.125 in) and a depth of 19.37 cm (7 5/8 in) for testing. The soil was baked out prior to compaction preparation as a measure to reduce soil moisture which interfered with pump down capacity. The soil was not baked again if it was removed from the vacuum chamber, prepped, and immediately returned to the vacuum chamber for pump down. The soil was compacted using a 60 Hz vibration table with a surcharge of 34 kg place on top of the soil in the container. Prepared soil samples weighed approximately 6.5 kg (bulk density 1.895-1.934 g/cm3). Two probe end effectors were tested: A cone penetrometer (static only) with a nominal diameter of 12.7 mm (0.5 in) and a nominal height of 28.6 mm (1.125 in); and a vibrating cylindrical probe measuring 12.7 mm in diameter and 50.8 mm in effective length from the tip (Figure 2). The cylindrical probe vibrated resonantly at 20 kHz with an amplitude 23 μm. The cone penetration tests were conducted to assess potential soil behavior differences in vacuum. The cylinder probe tests were conducted as the primary subject of this investigation to assess force response in vacuum. For each test, a regolith simulant sample was load-ed and compacted in the chamber, which was then evacuated for roughly 18 hours to reach the lowest possible pressure (approximately 5x10-6 Torr for most tests). The probe was then moved to about 10 mm above the soil surface before being pushed to a depth of 50 mm for the cylinder probe tests and to a depth of 100 mm for the cone penetrometer tests, both at a speed of 2 mm/s. The simulant samples were prepared the same for all tests. Ideally, they would respond consistently to probe penetration under ambient and vacuum conditions. This was evaluated by measuring the resistance of representative prepared simulant beds with a standard cone penetrometer in both environments. Results and Discussion: The resistance of the simulant samples in the vacuum tests was consistently lower than in the ambient tests as determined by the cone penetration tests. Thus, the ambient and vacuum results cannot be compared directly; work is underway to de-confound and better correlate the data. Still, figures 3-6 show that probe penetration forces are lower overall in the vacuum environment. In both environments, resonant vibration of the probe provides two useful effects: It reduces the probe penetration force and smooths the force-depth curve, significantly reducing local maxima. These effects have implications for various potential applications, such as astronaut hand-tools, where benefits (reducing astronaut effort) outweigh the cost of the additional energy re-quired to generate vibration. These results demonstrate that resonantly vibrating tools can meaningfully reduce the penetration force required for excavation, probing, and drilling tools in simulated lunar regolith deposits under vacuum levels approaching those that will be experience on the Moon’s surface. Lunar-gravity, ambient environment tests are scheduled soon. The effects of realistic temperatures and temperature gradients and deeper vacuum remain to be tested.

E Rezich↗
DOE OSTI2021

Mass enhancement in 3 d and s - p perovskites from symmetry breaking

In some d-electron oxides, the measured effective mass m* exptl has long been known to be significantly larger than the model effective mass m* model deduced from mean-field band theory, i.e., m* exptl =βm* model , where β>1 is the “mass-enhancement” or “mass-renormalization” factor. Previous applications of density functional theory (DFT), based on a symmetry-restricted structure with the smallest number of possible magnetic, orbital, and structural degrees of freedom, missed such mass enhancement. This fact has been taken as evidence of strong electronic correlation, often described via the symmetry-restricted dynamic mean-field approach of the many-body theory, being the exclusive enabling physics. This paper uses instead a static density functional approach that does not restrict positional or spin degrees of freedom (symmetry-broken structures). This approach analyzes the contributions of different symmetry-broken modalities to mass enhancement for a few nominally highly correlated d-electron perovskites as well as the nominally uncorrelated, closed-shell s-p bonding perovskites. It shows that the energy-lowering symmetry-broken spin effects (e.g., nonzero local moment in the paramagnetic phase) and structural effects (e.g., atomic displacement) as described in mean-field DFT already manifest mass enhancement for both electrons and holes in a range of d-electron perovskites SrVO 3 , SrTiO 3 , BaTiO 3 , and LaMnO 3 , as well as p-electron perovskites CsPbI 3 and SrBiO 3 , including both metals (SrVO 3 ) and insulators (the rest). This is revealed only when enlarged unit cells of the same parent global symmetry, which are large enough to allow for symmetry-breaking distortions and concomitant variations in spin order, are explored for their ability to lower the total energy. Positional symmetry breaking that leads to mass enhancement includes octahedral rotation in halide perovskites such as CsPbI 3 , Jahn-Teller-like Q${+}\atop{2}$ distortion in LaMnO 3 , and bond disproportionation in SrBiO 3 , while magnetic symmetry breaking resulting in mass enhancement includes the formation of a distribution of local moments in SrVO3 that averages to zero in the paramagnetic phase. Not all symmetry breaking leads to significant mass enhancement, e.g., the rather small octahedral rotations in the nearly perfectly cubic SrTiO 3 cause negligible mass enhancement, as do the paraelectric displacements in BaTiO 3 . In principle, by ergodicity, the two descriptions, i.e., the symmetry-restricted dynamic approach with a single time-fluctuating magnetic moment and the symmetry-broken mean-field approach with a static distribution of spatially fluctuated local moments, are not mutually exclusive but are a choice of representation and consequently, a choice of computational efficiency. In approximate implementations, the symmetry-broken mean-field approach appears to remove much of what was strong correlation in dynamically correlated symmetry-restricted solutions, leaving smaller (“weak”) residual correlation with respect to the exact solution.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Large Primtive Asteroids: Thermal and Dynamical Context

Primitiveasteroids, most of which are located in the outer belt and Jupiter’s Trojan clouds, provide information related to the origin and evolution of the solar system and the conditions in which the solar nebula was formed. These asteroids are widely thought to be the origin of the least-altered car-bonaceous chondrite that allow us to put crucial con-straints on the current dynamical and thermal theories of the formation and evolution of the early solar sys-tem. The nature of surface composition of large and low-albedo asteroids, like (1) Ceres, (10) Hygiea and (52) Europa, is still under intense debate and different interpretations have beenput forth to explain the ab-sorption features in these objects (e.g.,[1, 2, 3,4,5,6]). Laboratory and spectroscopic experiments on me-teorites that represent all nine carbonaceous chondrite types also found no spectral matches for these large asteroids (e.g.,[7]). Previous studies of asteroid Ceres (the largest primitive asteroid in the solar system) have been conducted to constrain and estimate its surface composition (e.g., [2, 5]). Using linear mixing,[2]found hydroxide brucite, serpentines, and carbonates, to be consistent with Ceres’ ground-based spectra.[5]estimated the surface composition of Ceres and found evidence of widespread NH3-phyllosilicates across its surface using best-fit solutions to Dawn’s NIR spectra. The presence of NH3-phyllosilicates implies that mate-rial from the outer solar system was incorporated into large primitive asteroids, either during their formation at great heliocentric distance or by incorporation of material transported into the Main Belt region. Here we presentnew largeand primitive asteroidsthat share the same spectral similaritieswith the largest asteroid in the solar system, Ceres.We also present the context of these new observations in terms oftheirthermal and dynamicalevolution.Large Primitive Asteroids: Dynamical and Thermal Context:Orbital Distribution of LargePrimitiveAsteroids: Constraining the mineralogy and surface composition of large primitive asteroids will place crucial con-straints on existing dynamical and thermal theories of the formation of the early solar system. We identified several additional asteroids in the Europa-like group in addition to asteroids Europa, Euphrosyne, and Patien-tia, that wereidentified in [8]using NASA IRTFtele-scope (e.g.,Figure 1). These new asteroids along with the already-observed Ceres-and Europa-like group members are localized in the 2.8 < a < 3.4 AU region and characterized by larger sizes, showing an interest-ing orbital distribution (Figure 2). Ceres-likeand Eu-ropa-like groups, which include the largest asteroids in the solar system, show an interesting orbital distribu-tion. These groups are located in the 2.6 < a < 3.6 AU region that contains the snow-line. The snow-line’s location may have been driftedinwards due to the disk’s cooling and evolution[9,10]. Recent dynamical models[11,12]suggested that a substantial fraction of primitive asteroids originated between or beyond the giant planets (a > 5 AU), where water ice would have been stable, and then implanted in the outer Main Belt region because of the giant planets’ growth.Figure 1. Two asteroids, 94 Aurora and 423 Diotima, showing spectra similar to asteroids (1)Ceres and (52)Europa.Thermal modeling and evolution of primitive aster-oids:Primitive water-rich asteroids are thought to be originally composed of mixtures of anhydrous materi-als and water ice that waslater melted by heating sources such as the decay of 26Al, reacting with anhy-drous materials to form H2O/OH-rich minerals. Calcu-lations of the evolution of the temperature and struc-ture of icy planetesimals were performedusing a 1D finite differences thermal evolution model[13, 14] for 26Al-heated planetesimals. In particular, thermally activated compaction due to hot pressing of bodies with an initially unconsolidated porous structure is included. An ice-rich initial composition that leads to a material dominated by phyllosilicates upon aqueous alteration (with 25 vol% H2O and a rock fraction that contains 85 vol% phyllosilicates and 15 vol% olivine upon aque-ous alteration, similar to CIand CM chondrites) was assumed. Atypical initial porosity of 40%[15] is re-duced following the change of the strain rate that is calculated as Voigt approximation from the strain rates of components[16]. Material properties (thermal con-ductivity, density, heat capacity, etc.) correspond to the composition assumed and are adjusted with tempera-ture and porosity. Melting of the water ice as well as water-rock separation are included[14]. Both short-and long-lived radionuclides are consideredas heat sources. Figure 3 shows the maximum temperature calculated as a function of radius and accretion time. A variety of internal structures is obtained, ranging from primordial (no melting of water ice) over partially melted or partially differentiated (melting of water ice, hydration, formation of a rocky core and water ocean below an undifferentiated layer) to completely differ-entiated ones (rocky core, water mantle, Enceladus-like case). The heating and differentiation of planetesi-mals is determined by the availability of 26Al, i.e., by the accretion time t0 relative to the formation of the calcium-aluminum-rich inclusions (CAIs), such that maximum temperatures and structures vary stronglyfor t0< 6 Myr rel. to CAIs. However, for a later accre-tion only the size of the body determines its maximum tempera-ture and structure due to the nearly constant heating by long-lived radionuclides. Average densities of Ceres-and Europa-like group membersimply high-ly porous interiors and, consequently, relatively late accretion at t0> 3 Myr rel. to CAIs with a maximum temperature of < 600 K (Figure3)

D Takir↗
NASA NTRS2001

Atmospheric Constraints on Landing Site Selection

The Martian atmosphere is a significant part of the environment that the Mars Exploration Rovers (MER) will encounter. As such, it imposes important constraints on where the rovers can and cannot land. Unfortunately, as there are no meteorological instruments on the rovers, there is little atmospheric science that can be accomplished, and no scientific preference for landing sites. The atmosphere constrains landing site selection in two main areas, the entry descent and landing (EDL) process and the survivability of the rovers on the surface. EDL is influenced by the density profile and boundary layer winds (up to altitudes of 5 to 10 km). Surface survivability involves atmospheric dust, temperatures and winds. During EDL, the atmosphere is used to slow the lander down, both ballistically and on the parachute. This limits the maximum elevation of the landing site to -1.3 km below the MOLA reference aeroid. The landers need to encounter a sufficiently dense atmosphere to be able to stop, and the deeper the landing site, the more column integrated atmosphere the lander can pass through before reaching the surface. The current limit was determined both by a desire to be able to reach the hematite region and by a set of atmosphere models we developed for EDL simulations. These are based on Thermal Emission Spectrometer (TES) atmospheric profile measurements, Ames Mars General Circulation Model (MGCM) results, and the 1-D Ames GCM radiative/convective model by J. Murphy. The latter is used for the near surface diurnal cycle. The current version of our model encompasses representative latitude bands, but we intend to make specific models for the final candidate landing sites to insure that they fall within the general envelope. The second constraint imposed on potential landing sites through the EDL process is the near surface wind. The wind in the lower approximately 5 km determines the horizontal velocity that the landers have when they land. Due to the mechanics of the landing process, the total velocity (including both the horizontal and vertical components) determines whether or not the landers are successful. Unfortunately, the landing system has no easy way to nullify any horizontal velocity imparted by the wind, so the landing sites selected need to have as little wind as possible. In addition to the mean wind velocity, the landing system is sensitive to vertical wind shear in the lowest kilometer or so. Wind shear can deflect the retro rockets (RADs) from their nominal vertical orientation producing unwanted horizontal spacecraft velocities. Both mean velocity and wind shear are dominated by the the local topography and other surface properties (in particular albedo and thermal inertia which control the surface temperature). This is seen even in simplified 2-D mesoscale models. The effects in a fully 3-D model are expected to he even more topographically dependent. In particular there is potential for wind channeling in canyons and other terrain features. Boundary layer winds and wind shear are currently being modeled based on terrestrial data and boundary layer scaling laws modified for Martian conditions. We hope to supplement this with mesoscale model results (from several sources) once the number of landing sites is reduced to a manageable number.

Kass, David M.↗
DOE OSTI2024

A static quantum embedding scheme based on coupled cluster theory

Here, we develop a static quantum embedding scheme that utilizes different levels of approximations to coupled cluster (CC) theory for an active fragment region and its environment. To reduce the computational cost, we solve the local fragment problem using a high-level CC method and address the environment problem with a lower-level Møller–Plesset (MP) perturbative method. This embedding approach inherits many conceptual developments from the hybrid second-order Møller–Plesset (MP2) and CC works by Nooijen [J. Chem. Phys. 111, 10815 (1999)] and Bochevarov and Sherrill [J. Chem. Phys. 122, 234110 (2005)]. We go beyond those works here by primarily targeting a specific localized fragment of a molecule and also introducing an alternative mechanism to relax the environment within this framework. We will call this approach MP-CC. We demonstrate the effectiveness of MP-CC on several potential energy curves and a set of thermochemical reaction energies, using CC with singles and doubles as the fragment solver, and MP2-like treatments of the environment. The results are substantially improved by the inclusion of orbital relaxation in the environment. Using localized bonds as the active fragment, we also report results for N=N bond breaking in azomethane and for the central C–C bond torsion in butadiene. We find that when the fragment Hilbert space size remains fixed (e.g., when determined by an intrinsic atomic orbital approach), the method achieves comparable accuracy with both a small and a large basis set. Additionally, our results indicate that increasing the fragment Hilbert space size systematically enhances the accuracy of observables, approaching the precision of the full CC solver.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2000

First-Generation Jet Propulsion Laboratory "Hockey-Puck" Free-Flying Magnetometers for Distributed In-Situ Multiprobe Measurement of Current Density Filamentation in the Northern Auroral Zone: Enstrophy Mission

The sub-orbital rocket mission was a collaborative project between the University of New Hampshire, Cornell University, and the Jet Propulsion Laboratory (JPL) to study filamentation phenomena in the northern Auroral zone. The Enstrophy mission test flies the JPL Free-Flying Magnetometer (FFM) concept. The FFM technology development task has been funded by NASA develop miniaturized, low-power, integrated "sensorcrafts". JPL's role was to design, integrate, test, and deliver four FFMs for deployment from the sounding rocket, allowing a unique determination of curl-B. This provides a direct measurement of magnetic-field-aligned current density along the rocket trajectory. A miniaturized three-axis fluxgate magnetometer was integrated with a 4-channel 22-bit sigma-delta Analog to Digital Converter (ADC), four temperature sensors, digital control electronics, seven (Li-SOCl2) batteries, two (4 deg x 170 deg field of view) sun-sensors, a fan-shaped-beam laser diode beacon, a (16 MHz) stable Temperature Compensated Crystal Oscillator (TCXO) clock, Radio Frequency (RF) communication subsystem, and an antenna for approximately 15 minutes of operation where data was collected continuously and transmitted in three (3) bursts (approximately 26 seconds each) to ground station antennas at Poker Flat, Alaska. FFMs were stowed within two trays onboard the rocket during the rocket launch and were released simultaneously using the spinning action of the rocket at approximately 300 km altitude (approximately 100 sec. into the flight). FFMs were deployed with spin rate of approximately 17 Hz and approximately 3 m/sec linear velocity with respect to the rocket. For testing purposes while the rocket was in the launch pad and during flight prior to release of FFMs from the rocket, commands (such as "power on", "test", "flight", "power off', and clock "Reset" signal) were transmitted via a infrared Light Emitting Diode to an infrared detector in the FFM. Special attention was paid to low magnetic signature electronic design and choice of materials in packaging. The miniaturized fluxgate magnetometers had a range of 1-60000 nT with 0.1% full-scale linearity. The frequency range of interest for magnetic measurement was 10 mHz - 50 Hz. Digital data from the magnetometer's three axes were placed in a 4MB Static Random Access Memory (SRAM) in data packages (frames) formatted together with time tags and frame ID. After a specified time was elapsed, the data were Viterbi encoded and transmitted at a rate of 100 kbps (BPSK). Each of the four FFMs transmitted at different frequency. These carrier frequencies were in the range of 2200-2300 MHz. The antenna was a single patch on a high dielectric constant substrate covering one end-plate of the hockey-puck-sized unit. The local clocks aboard the FFMs were reset at the start of the mission and stayed synchronized within 3 msec during the mission. Position of each FFM with respect to the rocket is calculated by the knowledge of its release velocity (measured at exit point of the FFM launcher tract) providing an accuracy of 1 m over the maximum range of 3 km. Spatial and temporal nature of observants can be separated to within 3 m in space or 3 msec time interval.

Javadi, H.↗
DOE OSTI2024

Substantial and overlooked greenhouse gas emissions from deep Arctic lake sediment - supporting data and code

This data package contains data, descriptions, and code-based analyses that were used to support conclusions drawn in “Substantial and overlooked greenhouse gas emissions from deep Arctic lake sediment”, by Freitas et al. (2025) (https://doi.org/10.1038/s41561-024-01614-y). The study evaluated greenhouse gas production along a deep sediment core (20 m) taken in 2018 from below Goldstream Lake, a field site approximately 15 km north of Fairbanks, Alaska.The file “ESSDive_NFreitas_2024_flmd.csv” includes an overview of all other csv files in this data package, namely: sediment descriptions (depth and type of sediment), sediment characterizations (bulk density, gravimetric water content, total carbon, etc.), calculated respiration and temperature sensitivity values associated with year-long incubations of the sediment core, and the R code used to process the dataset. Additional details regarding the content of these files and how the calculations were performed are described in the Methods section of this archive. The “data_dictionary_ESSDive_NFreitas_2024_dd.csv” is a data dictionary for all files included in the data package. Each row in the data dictionary represents a column name in a given file. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).Data package updates- August 2024: Title was updated, R code now includes a process for calculating potential production across the whole sediment column, the "sediment_column_production_potentials_ESSDive_NFreitas_2024.csv" is the associated data output file, and the file level metadata and data dictionaries were updated to reflect the contents of the additional csv file.- October 2024: Title was updated, and a statement was added to Step 2 of the Methods that describes that samples were collected (and exported) in a responsible manner and in accordance with relevant permits and local laws.- January 2025: Updated the associated manuscript details in the Abstract (manuscript title, publication date, DOI link) and in the Related References section (full citation).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Current data are consistent with flat spatial hypersurfaces in the Λ CDM cosmological model but favor more lensing than the model predicts

Here, we study the performance of three pairs of tilted, and a pair of untilited, ΛCDM cosmological models, with three of these four pairs allowing for non-flat spatial hypersurfaces, against cosmic microwave background (CMB) temperature and polarization power spectrum data (P18), measurements of the Planck 2018 lensing potential power spectrum (lensing), and a large compilation of non-CMB data (non-CMB). For the eight models, we measure cosmological parameters and study whether or not pairs of the data sets (as well as subsets of them) are mutually consistent in these models. Half of these models allow the lensing consistency parameter A L , which re-scales the gravitational potential power spectrum, to be an additional free parameter to be determined from data, while the other three have A L = 1 which is the theoretically expected value. The pair of untilted non-flat ΛCDM models are incompatible with P18 data. The tilted spatially-flat models assume the usual primordial spatial inhomogeneity power spectrum that is a power law in wave number. The tilted non-flat models assume either the primordial power spectrum used in the Planck group anal yses [Planck P(q)], that has recently been numerically shown to be a good approximation to what is quantum-mechanically generated from a particular choice of closed inflation model initial conditions, or a recently computed power spectrum [new P(q)] that quantum-mechanically follows from a different set of non-flat inflation model initial conditions. In the tilted non-flat models with A L = 1 we find differences between P18 data and non-CMB data cosmological parameter constraints, which are large enough to rule out the Planck P(q) model at 3σ but not the new P(q) model. No significant differences are found when cosmological parameter constraints obtained with two different data sets are compared within the standard tilted flat ΛCDM model. While both P18 data and non-CMB data separately favor a closed geometry, with spatial curvature density parameter Ω k < 0, when P18+non-CMB data are jointly analyzed the evidence in favor of non-flat hypersurfaces subsides. Differences between P18 data and non-CMB data cosmological constraints subside when A L is allowed to vary. From the most restrictive P18+lensing+non-CMB data combination we get almost model-independent constraints on the cosmological parameters and find that the A L > 1 option is preferred over the Ω k < 0 one, with the A L parameter, for all models, being larger than unity by ~ 2.5σ. According to the deviance information criterion, in the P18+lensing+non-CMB analysis, the varying A L option is on the verge of being strongly favored over the A L = 1 one, which could indicate a problem for the standard tilted flat ΛCDM model. These data are consistent with flat spatial hypersurfaces but more and better data could improve the constraints on Ω k and might alter this conclusion. Error bars on some cosmological parameters are significantly reduced when non-CMB data are used jointly with P18+lensing data. For example, in the tilted flat ΛCDM model for P18+lensing+non-CMB data the Hubble constant H 0 = 68.09 ± 0.38 km s -1 Mpc -1 , which is consistent with that from a median statistics analysis of a large compilation of H 0 measurements as well as with a number of local measurements of the cosmological expansion rate. This H 0 error bar is 31% smaller than that from P18+lensing data alone.

79 ASTRONOMY AND ASTROPHYSICS↗