Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “laser processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Continuous wave room temperature operation of the 2 $μ$m GaSb-based photonic crystal surface emitting diode lasers

Continuous wave room temperature operation of 2 μm GaSb-based photonic-crystal surface-emitting diode lasers has been realized. The deep etched square mesa devices showed threshold current densities of 500 A/cm 2 at 20 °C. The epi-side down mounted lasers generated above 10 mW of output power in the continuous wave regime and tens of milliwatts in pulses from the 200 × 200 μm 2 aperture. Here, the breakthrough in the device performance parameters was achieved thanks to a highly homogeneous air-pocket retaining epitaxial regrowth process optimized for a specifically designed antimonide diode laser heterostructure. The nanofabrication method utilizing low temperature atomic hydrogen surface cleaning yielded low disorder square lattice of droplet-shaped voids covered by uniform p-cladding layer. The laser emission spectrum as well as near/far field patterns demonstrated peculiar features presumably linked to deformation of the void shape during regrowth and formation of the array of filaments.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Nanosecond Laser Drying in Wafer Foundries for Significant Energy Efficiency Improvement

Surface drying is a critical process in microelectronics wafer fabrication. In order to reduce and eliminate watermarks, many surface drying processes have been studied and used. Most of the wafer foundries currently use drying processes based on Isopropyl Alcohol (IPA), which causes serious safety (fire), health, environmental, and energy efficiency issues. The long-term goal of this project is to develop a fast, effective, chemical-free, and extremely energy efficient wafer drying technology that employs nanosecond laser-induced sub-surface evaporation and explosion. The objectives of this project are to 1) experimentally develop and verify the laser surface drying method, explore and identify how and to what extent various physical parameters influence the drying efficiency and effectiveness; and 2) understand and optimize the underlying thermodynamics in the proposed laser surface drying, including micro/nanoscale sub-surface superheating, evaporation, explosion, and photo/thermochemical bond breaking via atomistic modeling and experimental characterization. Toward these objectives, five tasks have been accomplished successfully, including 1) develop in-lab laser surface drying setup and study the effect of varied laser parameters, 2) use multiscale hybrid-modeling to study and understand the physics of water behavior during drying toward process optimization, 3) investigate the effect of drying conditions on the drying effectiveness, 4) develop a large-scale laser drying scanning system with automatic scanning, and 5) conduct large-scale simulation to study the effect of dopant level and develop strategies for system development toward industry deployment.

42 ENGINEERING↗
DOE OSTI2024

Advanced Instrumentation for Metal Additive Manufacturing

Laser powder bed fusion (LPBF) is the most widely used process for metal additive manufacturing (AM), particularly where complex geometries provide performance advantages unattainable with traditional manufacturing techniques. However, LPBF is highly sensitive to innate variability in both the powder spreading and fusion steps, often leading to defects such as pores that are difficult to detect yet significantly impair component mechanical properties and fatigue life. This thesis presents a range of novel instruments enabling both precise assessment of powder layer characteristics and in-situ thermal metrology of metal AM to advance the quality control of LPBF. First, leveraging a custom X-ray microscope and a radiation-transport model developed through this work, transmission X-ray imaging is used to study spreading of thin metal powder layers. Effective layer depth is directly mapped at a process-relevant size scale, surpassing optical techniques that can only estimate local deposition from layer surface topography. Layer packing density and quality are shown to be influenced by powder flowability and particle size relative to nominal powder layer thickness. Layer quality is additionally connected to the geometry of the spreading implement and its velocity. This technique and its presented findings enable pairing feedstocks with spreading strategies that create layers with consistent packing density and uniformity. Second, a twofold approach is employed to optically interrogate the laser fusion step of LPBF for observing signatures of defect formation. Aperture division multiplexing is conceptualized, providing for simultaneous laser delivery and high-fidelity infrared (IR) process monitoring through a common optic. In-situ microscopy at 50 μm spatial resolution and at mid-wave IR wavelengths is proven readily achievable with the first purpose-built optic of this type. Next, a bespoke imaging spectrometer, along with a temperature-emissivity separation technique, is used to retrieve accurate process temperatures over a 1000 K range. Data from these instruments are correlated to porosity as fine as 4.3 μm in two LPBF test artifacts, as verified using computed tomography (CT), establishing the viability of robust optically-based component qualification.

Penny, Ryan↗
DOE OSTI2024

Microstructural Passivation of Patterned Al 2 O 3 Back Contacts on CdS/CdTe Solar Cells

Abstract Patterned aluminum oxide (Al 2 O 3 ) back contact on cadmium telluride (CdTe) solar cells can effectively mitigate the loss of the majority carriers while retaining the passivation benefits for minority carriers. This study investigates the impact of the point‐contact geometry on cell performance, where the spacing of the microholes is systematically varied at a constant microhole diameter (≈16 µm). Microhole arrays are created on an evaporated Al 2 O 3 layer (≈30 nm) on CdTe using laser‐beam lithography and selective wet etching processes. Comparative analysis indicates a significant decrease in fill factor (FF) and short‐circuit current ( I SC ) when the contact fraction falls below 30%, likely due to the Al 2 O 3 barrier impeding majority carriers. Above this fraction, FF and I SC are comparable to those of baseline CdTe cells without Al 2 O 3 . Open‐circuit voltage ( V OC ) shows a gradual decrease as Al 2 O 3 coverage is reduced but exhibits a slight increase (<15 mV) when the contact fraction exceeds 30%. Cathodoluminescence (CL) characterization reveals that significantly improved radiative recombination occurs within the CdTe grain bulk with Al 2 O 3 , whereas this effect on grain boundaries is minimal. The findings imply complex local carrier dynamics in the patterned back‐contact region, closely tied to the microstructural properties of CdTe‐based solar cells.

Roy, Etee Kawna↗
DOE OSTI2025

Solute Redistribution During Aging in a Laser-Based Powder Bed Fusion-Produced Fe-18Ni-9Co-5Mo-Ti Maraging Steel

Solute distribution during the laser-based powder bed fusion of metals process is highly complex because of solidification. This study builds on a previous investigation of how solute heterogeneities across different scales influence phase distribution and aging physical phenomena in a Fe-18Ni-9Co-5Mo-Ti maraging steel (Santana et al. in Addit Manuf 104494, 2024). Previous work using energy-dispersive X-ray spectroscopy revealed heterogeneous Ni and Mo enrichment at intercellular regions. Using X-ray diffraction, 8 ± 3% retained austenite was quantified in as-built samples. Additionally, electron backscatter diffraction analysis exposed the location of retained austenite along cell boundaries. In this work, scanning transmission electron microscopy results revealed the presence of non-enriched retained austenite in the as-built condition. With increased aging temperature, Ni and Mo enrichment in austenite increased, especially at the austenite/martensite boundary. Solute diffusion was simulated in DICTRA Thermo-Calc® software to assess solute redistribution between the matrix and second phases and to comprehend whether elemental diffusion processes are interconnected. Three different scenarios were considered: (1) solute diffusion in the matrix; (2) diffusion with enriched austenite in the intercellular region; (3) diffusion with non-enriched austenite in the intercellular region. Results showed that Ni partitioning controls austenite growth and that boundary regions exhibit higher element enrichment than the core.

42 ENGINEERING↗
DOE OSTI2022

Fatigue performance of laser powder bed fusion hydride-dehydride Ti-6Al-4V powder

We report hydride-dehydride (HDH) Ti-6Al-4V alloy with particle size distribution of 50–120 µm is laser powder bed fusion (L-PBF) processed using optimum processing parameters and a near-fully dense structure with a density of 99.9 % is achieved. Microstructural observations and phase analyses indicate formation of columnar β grains with acicular α/α' phases in as-built condition. The roughness of the as-fabricated samples is significant with an average roughness of R a = 15.71 ± 3.96 µm and a root mean square roughness of R rms = 108.4 ± 24.9 µm, however, both values are reduced to R a = 0.19 ± 0.04 µm and R rms = 4.9 ± 0.6 µm after mechanical grinding. Mechanical tests are carried out on as-fabricated specimens followed by stress relief treatment. All samples are tested to failure in fatigue, under fully-reversed tension-compression conditions of R = –1. The as-built samples failed from the surface with crack initiation mainly at micro-notches, whereas after mechanically grinding, crack initiation changed to subsurface defects such as pores. Minimizing surface roughness by mechanically grinding eliminates surface micro-notches which improves fatigue strength in the high cycle fatigue region. Fatigue notch factor calculations showed that the effect of surface roughness was significantly lower when HDH powder is used compared to standard spherical powder. X-ray diffraction analysis revealed an in-plane compressive stress, micro-strain and grain refinement on the surface of the mechanically ground samples. Fractography observations (macroscale) revealed a fully brittle fracture in the first stage of crack growth with a transition to a dominantly ductile fracture in the third stage of crack growth. On the other hand, at the micro scale, even the brittle fracture regions showed evidence of ductile fracture within the α' martensite laths.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Differentiable lagrangian shock hydrodynamics with application to stable shock acceleration of density interfaces

We develop a gradient based optimization approach for the equations of compressible, Lagrangian hydrodynamics and demonstrate how it can be employed to automatically uncover strategies to control hydrodynamic instabilities arising from shock acceleration of density interfaces. Strategies for controlling the Richtmyer-Meshkov instability (RMI) are of great benefit for inertial confinement fusion (ICF) where shock interactions with many small imperfections in the density interface lead to instabilities which rapidly grow over time. These instabilities lead to mixing which, in the case of laser driven ICF, quenches the runaway fusion process ruining the potential for positive energy return. Here, we demonstrate that control of these instabilities can be achieved by optimization of initial conditions with ( > 100) parameters. Optimizing over a large parameter space like this is not possible with gradient-free optimization strategies. This requires computation of the gradient of the outputs of a numerical solution to the equations of Lagrangian hydrodynamics with respect to the inputs. We show that the efficient computation of these gradients is made possible via a judicious application of (i) adjoint methods, the exact formal representation of sensitivities involving partial differential equations, and (ii) automatic differentiation (AD), the algorithmic calculation of derivatives of functions. Careful regularization of multiple operators including artificial viscosity and timestep control is required. We perform design optimization of > 100 parameter energy field driving the Richtmyer Meshkov instability showing significant suppression while simultaneously enhancing the acceleration of the interface relative to a nominal baseline case.

Hydrophysics↗
DOE OSTI2025

Photoionization of seeded combustion products as a method of enhancing the efficiency of magnetohydrodynamic power generators

Here, in this study, we performed an experimental and computational investigation into the feasibility of utilizing photoionization to enhance the electrical conductivity of seeded oxy-fuel combustion products and improve the performance of magnetohydrodynamic (MHD) power generators. We applied a variety of optical and microwave diagnostics to study the ionization and recombination processes of potassium excited by an excimer laser in a high-velocity oxy-fuel free jet. Computational fluid dynamic (CFD) simulations were performed to model the thermophysical properties and species densities of the free jet. The CFD results were validated with position-dependent potassium concentration measurements. Electron recombination exponential lifetimes were measured through time-resolved microwave transmission. The experimental electron lifetimes were compared with lifetimes calculated from CFD-predicted species densities and literature recombination rates. It was determined that K + or O 2 are the most likely recombination partners for photoionized electrons. Time-resolved fluorescence measurements provided evidence of an ionization pathway involving a two-photon ionization of KOH . Finally, a zero-dimensional chemical kinetic model was developed to assess the fundamental viability of inducing a non-equilibrium electron population to provide a net energy return in combustion-driven MHD power generators. We determined that a high energy return is feasible for targeting electrode boundary layers with ultraviolet photoionization. We also found that photoionization could potentially lower the required temperature of the bulk gas flow.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2020

Forward modeling of Doppler velocity interferometer system for improved shockwave measurements

We report that when near-instantaneous shocks are recorded by using a Doppler velocity interferometer velocity interferometer system for any reflector (VISAR), they typically exceed the detector’s ability to react and “skipped fringes” result, where its visibility briefly reduces. Traditionally, replacing skipped fringes required guesswork in analysis, which increased arrival time errors. Second, the use of long but velocity-sensitive interferometer delays with fast detectors which can resolve the delay has traditionally been avoided because of the fear of confusing the arrival time signal. However, shorter delays produce smaller fringe phase shifts per velocity and, thus, can decrease velocity precision. We realize that while some loss of fringe information occurs at shock events, this is often just a partial loss and the residual fringe information can still hold valuable information. We describe a forward model (FM) of the interferometer action and detector blurring that assists with VISAR fringe analysis at skipping events: (1) more precise shock arrival times, (2) arrival time precision not limited by long delays, and (3) improved ghost subtraction, which improves accuracy over a broad time region. Lastly, we demonstrate the utility of a FM on National Ignition Facility and Laboratory for Laser Energetics Omega shots and discuss data process methods to increase the high time resolution of VISAR systems despite their limitations and complexities.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Reduction of bright exciton lifetimes by radiation-induced disorder

Quantum-radiative decay is a fundamental process in many optoelectronic systems such as laser diodes and solar cells. The bright exciton lifetime is a critical factor in determining the performance of these systems. Motivated by the ever-increasing need for laser systems in space and nuclear applications, we develop a many-particle approach to predict the radiative lifetime under harsh radiation environments. Here, using GaAs as a model system, we find that radiation-induced band tailing reduces the bright exciton lifetime. This result shows that the efficiency of radiative recombination, in addition to nonradiative recombination, can be affected by ionization radiation. Our approach enables a detailed understanding of the interplay between correlation, localization, and radiation that affect the performance of gain media.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Design of an Additively Manufactured Recuperator With 800 °C Inlet Temperature for sCO2 Power Cycle Application

Abstract Recuperators with design temperatures at and above 800 °C can further increase the thermal efficiency of supercritical CO2 power cycles by enabling higher turbine exhaust temperatures. Mar-M247 is a well-suited nickel-based superalloy for high temperature service due to its high creep strength that prevents excessive material thickness being required for pressure containment. Additive manufacturing using a high-speed laser-directed energy deposition (L-DED) process presents a promising solution, with build trials demonstrating the ability to produce nonconventional flow channels for enhanced heat transfer. A design process is presented that includes aerothermal and mechanical evaluation to maximize performance within the constraints of the manufacturing process. A 2-D heat transfer network and pressure drop code allows prediction of flow distribution and its effect on overall thermal performance. Established literature correlations, along with CFD simulation, inform the prediction of heat transfer coefficients and friction factors for the flowpaths and enhancement features in the heat exchanger core. Mechanical evaluation using finite element analysis (FEA) modeling with the intent of the ASME Boiler & Pressure Vessel Code (BPVC) Section VIII, Div. 2 assesses the operational safety of the design. The detailed design features annular finned passages that take advantage of helical flow paths to distribute the flow from separated headers to shared heat transfer surfaces. Performance predictions for the recuperator at a 50 kW scale provide insights into the feasibility of the additively manufactured (AM) process to produce recuperators on a commercial scale that extend existing operating envelopes.

Engineering↗
DOE OSTI2024

Development of a Method for Shape Optimization for a Gas Turbine Fuel Injector Design Using Metal-Additive Manufacturing

Adjoint shape optimization has enabled physics-based optimal designs for aerodynamic surfaces. Additive manufacturing (AM) makes it possible to manufacture complex shapes. However, there has been a gap between optimal and manufacturable surfaces due to the inherent limitations of commercial computational fluid dynamics (CFD) codes to implement geometric constraints during adjoint computation. In such cases, the design sensitivities are exported and used to perform constrained shape modifications using parametric information stored in computer aided design (CAD) files to satisfy manufacturability constraints. However, modifying the design using adjoint methods in CFD solvers and performing constrained shape modification in CAD can lead to inconsistencies due to different shape parameterization schemes. This paper describes a method to enable the simultaneous optimization of the fluid domain and impose AM manufacturability constraints, resolving one of the key issues of geometry definition for isogeometric analysis. Similar to a grid convergence study, the proposed method verifies the consistencies between shape parameterization techniques present within commercial CAD and CFD software during mesh movement as a part of the adjoint shape optimization routine. By identifying the appropriate parameters essential to a shape optimization study, the error metric between the different parameterization techniques converges to demonstrate sufficient consistencies for justifiable exchange of data between CAD and CFD. For the identified shape optimization parameters, the error metric to measure the deviation between the two parameterization schemes lies within the AM laser-powder bed fusion (L-PBF) process tolerance. Additionally, comparison for subsequent objective function calculations between iterations of the optimization loop showed acceptable differences within 1% variation between the modified geometries obtained using the two parameterization schemes. This method provides justification for the use of multiphysics guided adjoint design sensitivities computed in CFD software to perform shape modifications in CAD to incorporate AM manufacturability constraints during the shape optimization loop such that optimal designs are also additively manufacturable.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

High‐Throughput Computational Guided Development of Refractory Complex Concentrated Alloys‐based Composite

ULTIMATE is a leading-edge DOE program to develop ultrahigh temperature materials for gas turbine use in the aviation and power generation industries. This team, headquartered at West Virginia University and including collaborators from the National Energy Technology Laboratory and Advanced Manufacturing LLC, has developed a new class of ultra-high temperature Refractory Complex Concentrated Alloys-based Composites (RCCC) for high temperature applications such as combustion turbines used in the aerospace and energy industries. The RCCC consist of Refractory Complex Concentrated Alloys (RCCA) mixed with particles of Refractory High Entropy Carbides, to increase RCCA strength to withstand extreme conditions. These new materials optimize the balance among strength, creep (deformation), density, and stability at 1300 °C (2372 °F), while maintaining ductility once the alloy cools to room temperature. The research team has developed advanced manufacturing processes using the pulsed electric current and laser 3D printing to produce test coupons of these materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tensile Performance Sensitivity to Variations of Standard 17-4 PH Heat Treatments on LPBF-Produced Material

Standard heat treatments for metals of a particular composition are typically designed with the assumption of a conventional starting microstructure, such as that produced by casting or wrought processing. When applied to metals fabricated by Laser Powder Bed Fusion (LPBF) metal additive manufacturing (AM), these heat treatments can produce inconsistent performance due to the unique as-built microstructures. This study investigates how modifications to standard heat treatments for 17-4 PH steel influence the microstructure and mechanical properties of LPBF-fabricated material. Specimens were produced and subjected to varying solutionizing and homogenizing treatments followed by standard aging treatments. Microstructures were characterized using optical microscopy, Electron Backscatter Diffraction (EBSD), and X-ray diffraction (XRD), and mechanical properties were evaluated through uniaxial tensile testing. Based on these results, recommendations are provided for achieving improved wrought-like performance in LPBF 17-4 PH steel.

17-4 PH↗
DOE OSTI2022

Self-alignment features for III-V ridge process and angled facet die

A method of forming a laser including device is provided that in one embodiment includes providing a laser chip including at least one ridge structure that provides an alignment features. The method further includes bonding a type IV photonics chip to the laser chip, wherein a vertical alignment feature from the type IV photonics chip is inserted in a recess relative to the at least one ridge structure that provides the alignment features of the laser structure.

Barwicz, Tymon↗
DOE OSTI2023

Defect Characterization of Monocrystalline Silicon Solar Cells with Polysilicon Passivated Contact Using Electrically-Detected Magnetic Resonance (EDMR) Spectroscopy

As the c-Si based solar cell efficiencies are approaching over 26%, it is becoming critical to characterize the low concentrations of the defects – as low as 10^10-10^11 cm-3 (for e.g., iron contamination in high-lifetime Ga-doped wafers3 and n-type wafers), and further reduce them. Also, atomistic level understanding of the mechanisms of the low concentration process-induced-defects and reliability limiting defects (such as light and elevated temperature induced degradation, surface passivation degradation) is needed to design the mitigation strategies. The conventional characterization techniques are limited due to their detection limitations. Some of the techniques based on lifetime spectroscopies can still be used for low concentration characterization however, they are based on estimations and theoretical models and hence, indirect and cannot fully reveal information about the microscopic mechanism of the defects. Thus, we present the application of an ultrasensitive magnetic resonance-based technique for the direct spectroscopic detection of the defects in Si PV - electrically detected magnetic resonance (EDMR). In this work, we aim to focus on establishing a process flow for fabrication of minicells with (miniature replica of the larger-area cells) and setting up the routine for EDMR measurements on them with the EDMR instrumentation capability at NREL. For the EDMR measurements, sample size is limited by the dimensions of sample holder tube (width less than 3.2 mm, active area - 20 mm). Thus, we have designed c-Si based minicells with polysilicon (poly-Si) passivated contacts same as the larger-area cells that we fabricate in our group at NREL. We also modified our minicell process flow for fabricating the textured minicells for preserving the texture during processing and taking care of the laser-ablation edge damage which can significantly affect the performance of such small devices. We have achieved comparable performance on these newly fabricated minicells as that of our 4 cm2 devices with same structure (comparable VOC, JSC, FF). We also conducted EDMR measurements on the minicells and observed a distinct EDMR signal at g-value ~2.005 at temperatures 30K and above, as shown in Fig. 2. We associate this signal to the presence of silicon dangling bonds based on the g-value. We also observed an EDMR signal at g-value ~1.998 at temperature ~5K. The origin of this signal is still being investigated. Thus, we show the proof of concept of minicells and EDMR measurements with which we now aim to study some of the unknown defects in silicon solar cell devices.

EDMR↗