Results for “fiber” — Page 40

NASA NTRS2003

Oxidation of Carbon Fibers in Water Vapor Studied

T-300 carbon fibers (BP Amoco Chemicals, Greenville, SC) are a common reinforcement for silicon carbide composite materials, and carbon-fiber-reinforced silicon carbide composites (C/SiC) are proposed for use in space propulsion applications. It has been shown that the time to failure for C/SiC in stressed oxidation tests is directly correlated with the fiber oxidation rate (ref. 1). To date, most of the testing of these fibers and composites has been conducted in oxygen or air environments; however, many components for space propulsion, such as turbopumps, combustors, and thrusters, are expected to operate in hydrogen and water vapor (H2/H2O) environments with very low oxygen contents. The oxidation rate of carbon fibers in conditions representative of space propulsion environments is, therefore, critical for predicting component lifetimes for real applications. This report describes experimental results that demonstrate that, under some conditions, lower oxidation rates of carbon fibers are observed in water vapor and H2/H2O environments than are found in oxygen or air. At the NASA Glenn Research Center, the weight loss of the fibers was studied as a function of water pressure, temperature, and gas velocity. The rate of carbon fiber oxidation was determined, and the reaction mechanism was identified.

Opila, Elizabeth J.↗

NASA NTRS2007

In-Plane Cracking Behavior and Ultimate Strength for 2D Woven and Braided Melt-Infiltrated SiC/SiC Composites Tensile Loaded in Off-Axis Fiber Directions

The tensile mechanical properties of ceramic matrix composites (CMC) in directions off the primary axes of the reinforcing fibers are important for architectural design of CMC components that are subjected to multi-axial stress states. In this study, 2D-woven melt-infiltrated (MI) SiC/SiC composite panels with balanced fiber content in the 0 degree and 90 degree directions were tensile loaded in-plane in the 0 degree direction and at 45 degree to this direction. In addition, a 2D triaxially-braided MI composite panel with balanced fiber content in the plus or minus 67 degree bias directions and reduced fiber content in the axial direction was tensile loaded perpendicular to the axial direction tows (i.e., 23 degrees from the bias fibers). Stress-strain behavior, acoustic emission, and optical microscopy were used to quantify stress-dependent matrix cracking and ultimate strength in the panels. It was observed that both off-axis loaded panels displayed higher composite onset stresses for through-thickness matrix cracking than the 2D-woven 0/90 panels loaded in the primary 0 degree direction. These improvements for off-axis cracking strength can in part be attributed to higher effective fiber fractions in the loading direction, which in turn reduces internal stresses on critical matrix flaws for a given composite stress. Also for the 0/90 panel loaded in the 45 degree direction, an improved distribution of matrix flaws existed due to the absence of fiber tows perpendicular to the loading direction. In addition, for the +67/0/-67 braided panel, the axial tows perpendicular to the loading direction were not only low in volume fraction, but were also were well separated from one another. Both off-axis oriented panels also showed relatively good ultimate tensile strength when compared to other off-axis oriented composites in the literature, both on an absolute strength basis as well as when normalized by the average fiber strength within the composites. Initial implications are discussed for constituent and architecture design to improve the directional cracking of SiC/SiC CMC components with MI matrices.

Morscher, Gregory N.↗

NASA NTRS1980

Ion-exchange hollow fibers

An ion-exchange hollow fiber is prepared by introducing into the wall of the fiber polymerizable liquid monomers, and polymerizing the monomers therein to form solid, insoluble, cross-linked, ion-exchange resin particles which embed in the wall of the fiber. Excess particles blocking the central passage or bore of the fiber are removed by forcing liquid through the fiber. The fibers have high ion-exchange capacity, a practical wall permeability and good mechanical strength even with very thin wall dimensions. Experimental investigation of bundles of ion-exchange hollow fibers attached to a header assembly have shown the fiber to be very efficient in removing counterions from solution.

Rembaum, Alan↗

NASA NTRS1999

Fiber optic sensors for gas turbine control

An apparatus for detecting flashback occurrences in a premixed combustor system having at least one fuel nozzle includes at least one photodetector and at least one fiber optic element coupled between the at least one photodetector and a test region of the combustor system wherein a respective flame of the fuel nozzle is not present under normal operating conditions. A signal processor monitors a signal of the photodetector. The fiber optic element can include at least one optical fiber positioned within a protective tube. The fiber optic element can include two fiber optic elements coupled to the test region. The optical fiber and the protective tube can have lengths sufficient to situate the photodetector outside of an engine compartment. A plurality of fuel nozzles and a plurality of fiber optic elements can be used with the fiber optic elements being coupled to respective fuel nozzles and either to the photodetector or, wherein a plurality of photodetectors are used, to respective ones of the plurality of photodetectors. The signal processor can include a digital signal processor.

Shu, Emily Yixie↗

NASA NTRS2003

Fiber optic sensors for gas turbine control

An apparatus for detecting flashback occurrences in a premixed combustor system having at least one fuel nozzle includes at least one photodetector and at least one fiber optic element coupled between the at least one photodetector and a test region of the combustor system wherein a respective flame of the fuel nozzle is not present under normal operating conditions. A signal processor monitors a signal of the photodetector. The fiber optic element can include at least one optical fiber positioned within a protective tube. The fiber optic element can include two fiber optic elements coupled to the test region. The optical fiber and the protective tube can have lengths sufficient to situate the photodetector outside of an engine compartment. A plurality of fuel nozzles and a plurality of fiber optic elements can be used with the fiber optic elements being coupled to respective fuel nozzles and either to the photodetector or, wherein a plurality of photodetectors are used, to respective ones of the plurality of photodetectors. The signal processor can include a digital signal processor.

Shu, Emily Yixie↗

NASA NTRS2005

Fiber optic sensors for gas turbine control

An apparatus for detecting flashback occurrences in a premixed combustor system having at least one fuel nozzle includes at least one photodetector and at least one fiber optic element coupled between the at least one photodetector and a test region of the combustor system wherein a respective flame of the fuel nozzle is not present under normal operating conditions. A signal processor monitors a signal of the photodetector. The fiber optic element can include at least one optical fiber positioned within a protective tube. The fiber optic element can include two fiber optic elements coupled to the test region. The optical fiber and the protective tube can have lengths sufficient to situate the photodetector outside of an engine compartment. A plurality of fuel nozzles and a plurality of fiber optic elements can be used with the fiber optic elements being coupled to respective fuel nozzles and either to the photodetector or, wherein a plurality of photodetectors are used, to respective ones of the plurality of photodetectors. The signal processor can include a digital signal processor.

Shu, Emily Yixie↗

NASA NTRS1977

Ion-exchange hollow fibers

An ion-exchange hollow fiber is prepared by introducing into the wall of the fiber polymerizable liquid monomers, and polymerizing the monomers therein to form solid, insoluble, cross-linked, ion-exchange resin particles which embed in the wall of the fiber. Excess particles blocking the central passage or bore of the fiber are removed by forcing liquid through the fiber. The fibers have high ion-exchange capacity, a practical wall permeability and good mechanical strength even with very thin wall dimensions. Experimental investigation of bundles of ion-exchange hollow fibers attached to a header assembly have shown the fiber to be very efficient in removing counterions from solution.

Rembaum, Alan↗

NASA NTRS1988

Method for polishing the end of an optical fiber

A method of polishing a roof-shaped, or bevelled, tip having a predetermined angle on the end of an optical fiber is disclosed. The method comprises placing an optical fiber in contact with an abrasive tape at an angle corresponding to the desired predetermined angle. The fiber is moved towards the tape beyond the point of contact so as to cause a bend in the fiber. Upon moving the abrasive tape, the compliance of the fiber, by virtue of the bend, provides a pressure of the fiber against the tape to enable polishing to occur. As polishing continues the pressure decreases until enough material is removed so as to eliminate the bend and impart the predetermined angle to the fiber tip. The fiber may be rotated to polish the other side in a similar manner, if so desired.

Dholakia, Anil R.↗

NASA NTRS2011

Monolithic, High-Speed Fiber-Optic Switching Array for Lidar

Current fiber switch technologies use mechanical means to redirect light beams, resulting in slow switch time, as well as poor reliability due to moving parts wearing out quickly at high speeds. A non-mechanical ability to switch laser output into one of multiple fibers within a fiber array can provide significant power, weight, and costs savings to an all-fiber system. This invention uses an array of crystals that act as miniature prisms to redirect light as an electric voltage changes the prism s properties. At the heart of the electro-optic fiber-optic switch is an electro- optic crystal patterned with tiny prisms that can deflect the beam from the input fiber into any one of the receiving fibers arranged in a linear array when a voltage is applied across the crystal. Prism boundaries are defined by a net dipole moment in the crystal lattice that has been poled opposite to the surrounding lattice fabricated using patterned, removable microelectrodes. When a voltage is applied across the crystal, the resulting electric field changes the index of refraction within the prism boundaries relative to the surrounding substrate, causing light to deflect slightly according to Snell s Law. There are several materials that can host the necessary monolithic poled pattern (including, but not limited to, SLT, KTP, LiNbO3, and Mg:LiNbO3). Be cause this is a solid-state system without moving parts, it is very fast, and does not wear down easily. This invention is applicable to all fiber networks, as well as industries that use such networks. The unit comes in a compact package, can handle both low and high voltages, and has a high reliability (100,000 hours without maintenance).

Suckow, Will↗

NASA NTRS2004

Tool for Insertion of a Fiber-Optic Terminus in a Connector

A tool has been developed for the special purpose of inserting the terminus of an optical fiber in a cable connector that conforms to NASA Specification SSQ- 21635. What prompted the development of the tool was the observation that because of some aspects of the designs of fiber-optic termini and of springs, sealing rings, and a grommet inside the shell of such a connector, there is a tendency for the grommet to become damaged and detached from the sealing rings during installation. It is necessary to ensure the integrity of the grommet for proper sealing and proper functioning of the connector. The special-purpose tool provides the needed protection for the grommet. The grommet-protection tool resembles a funnel into which an axial slit has been cut (see figure). Prior to insertion, the grommet-protection tool is rolled so that one side of the slit overlaps the other side. The rolled-up grommet-protection tool is inserted in one of the connector holes that accommodate the fiber-optic termini and is pushed in until the flange (the wider of the two conical portions) of the tool becomes seated on the connector grommet. Then a special-purpose installation tool is inserted in the flange of the grommet-protection tool and pressed in until it becomes seated in the flange. This operation expands the narrower of the two conical portions of the grommet-protection tool. The installation tool is removed and the grommet-protection tool remains expanded due to the flat surfaces on the axial slit. By use of a standard contact-insertion tool, a fiber-optic terminus is inserted, through the grommet-protection tool, into the connector cavity. By use of a pair of forceps or needle-nose pliers, the grommet-protection tool is then pulled out of the cavity. Finally, the grommet-protection tool is removed from around the installed fiber-optic cable by pulling the cable through the axial slit. Unlike in some prior procedures for installing the fiber-optic termini in the connector, the procedure that involves the use of the present grommet-protection tool does not include the use of lubricants that can contaminate the interior of the connector. The grommet-protection tool is made of a fluoropolymer, taking advantage of the flexibility of such polymers and further taking advantage of the inherent slipperiness of fluoropolymers. Although the tool is designed primarily for insertion of a fiber-optic terminus, it might also be useful for extracting a previously installed fiber-optic terminus.

King, Wes↗

NASA NTRS2009

Nano-Fiber Reinforced Enhancements in Composite Polymer Matrices

Nano-fibers are used to reinforce polymer matrices to enhance the matrix dependent properties that are subsequently used in conventional structural composites. A quasi isotropic configuration is used in arranging like nano-fibers through the thickness to ascertain equiaxial enhanced matrix behavior. The nano-fiber volume ratios are used to obtain the enhanced matrix strength properties for 0.01,0.03, and 0.05 nano-fiber volume rates. These enhanced nano-fiber matrices are used with conventional fiber volume ratios of 0.3 and 0.5 to obtain the composite properties. Results show that nano-fiber enhanced matrices of higher than 0.3 nano-fiber volume ratio are degrading the composite properties.

Chamis, Christos C.↗

NASA NTRS2018

Modeling Fiber Kinking at the Microscale and Mesoscale

A computational micromechanics (CMM) model is employed to interrogate the assumptions of a recently developed mesoscale continuum damage mechanics (CDM) model for fiber kinking. The CMM model considers an individually discretized three dimensional fiber and surrounding matrix accounting for nonlinearity in the fiber, matrix plasticity, fiber/matrix interface debonding, and geometric nonlinearity. Key parameters of the CMM model were measured through experiments. In particular, a novel experimental technique to characterize the in situ longitudinal compressive strength of carbon fibers through indentation of micropillars is presented. The CDM model is formulated on the basis of Budiansky's fiber kinking theory (FKT) with a constitutive deformation-decomposition approach to alleviate mesh size sensitivity. In contrast to conventional mesoscale CDM models that prescribe a constitutive response directly, the response of the proposed model is an outcome of material nonlinearity and large rotations of the fiber direction following FKT. Comparison of the predictions from the CMM and CDM models shows remarkable correlation in strength, post-peak residual stress, and fiber rotation, with less than 10% difference between the two models in most cases. Additional comparisons are made with several fiber kinking models proposed in the literature to highlight the efficacy of the two models. Finally, the CMM model is exercised in parametric studies to explore opportunities to improve the longitudinal compression strength of a ply through the use of nonconventional microstructures.

Herraez, Miguel↗

NASA NTRSDate not supplied

New Developments in the CompDam Fiber Kinking Model for the Interaction

This paper describes two new additions to the CompDam fiber kinking model: 1) a failure index for fiber kinking to facilitate interaction between kinking and matrix cracking and 2) a strain-based criterion for fiber rupture to account for fiber breakage before or after fiber kinking. The model formulation is described with the aid of the graphical Considère construction, which is used to determine the conditions for fiber kinking. Verification studies are conducted with single element models to show the behavior of the model in light of the new developments and to evaluate the effect of numerical parameters of the model. The model is used to analyze open hole compression (OHC) specimens with soft, quasi-isotropic, and hard layups. Analysis results are shown for a conventional continuum damage mechanics model using a trilinear constitutive law for fiber damage and for the proposed model to highlight the differences between the two. Comparison with test data highlights the capabilities and remaining gaps in the quantitative prediction of the damage and failure response. While both models can predict many features of the OHC response, accurate prediction of kinking onset in the OHC specimens remains elusive. The results suggest that it is necessary to predict the combined effects of compression and shear loading as well as the structural effects (e.g., ply thickness, strain gradient effect) accurately to match the experimental observations of fiber kinking onset in the three OHC laminates.

Andrew C. Bergan↗

DOE OSTI2018

Scintillator based fiber optic plate for neutron imaging applications and the like

A chalcopyrite, colquiriite, neutron absorber loaded glass, or plastic scintillator based fiber optic plate for use in a neutron imaging system, including: a plurality of optical fiber segments disposed side-by-side adjacent to one another in a parallel array; and a binder material disposed between and coupling the plurality of optical fiber segments together. A diffuse reflective material is optically coupled to the plurality of first ends of the plurality of optical fiber segments. An optical detector device is optically coupled to the plurality of second ends of the plurality of optical fiber segments opposite the diffuse reflective material. Optionally, the fiber optic plate further includes a diffuse reflective material disposed one or more of on an exterior surface of each of the plurality of optical fiber segments and between the plurality of optical fiber segments.

42 ENGINEERING↗

DOE OSTI2021

Fiber laser microphones with graphene diaphragms

An acoustic sensor comprises a sensing head comprising an optical fiber having a tip. A graphene diaphragm is disposed on the tip and is configured to vibrate in response to an acoustic signal. A fiber laser is optically coupled to the sensing head. The fiber laser comprises a first set of fiber Bragg gratings and a second set of fiber Bragg gratings. A gap is present between the first set and the second set of fiber Bragg gratings. The fiber laser is configured to generate a sensing optical signal having a first intensity in response to an excitation optical signal, the sensing optical signal impinging on the graphene diaphragm such that a feedback optical signal is reflected from the graphene diaphragm towards the fiber laser and has and has a second intensity modulated by the vibration of the graphene diaphragm that corresponds to the acoustic signal.

Liao, Shaolin↗

DOE OSTI2021

Fiber Orientation Evaluation in Reinforced Composites using Digital Image Correlation

This paper presents an innovative nondestructive evaluation (NDE) approach to evaluate fiber orientation in fiber reinforced composites utilizing digital image correlation (DIC). Fiber orientation is a crucial factor that influences the mechanical and thermal properties of the composite. Conventional methods for fiber orientation evaluation and measurement are either destructive, which are typically laborious. NDE methods such as micro computed tomography are expensive and limited in sample size. In this work, we evaluate two methods of excitation of the composite, namely-quasistatic mechanical loading and thermal cycling. Digital Image Correlation (DIC) has been employed in conjunction for fiber orientation measurements. The DIC system is able to measure the fiber orientation by capturing 19x higher strain in the transverse direction of the reinforced fiber axis during excitation. The larger strain occurs in the transverse direction due to larger elongation in the surrounding polymer matrix than the fiber which resists elongation. This innovative method is within the preliminary stage and has been developed to fill the gap/limitations of other NDE methods.

Spencer, Ryan↗

DOE OSTI2021

A Novel Fiber-Bragg-Grating-Based Unique Identifier for Use in Tags and Seals

Tags and seals are important tools used in safeguards regimes for the control of nuclear materials. Vital to a successful tag or seal is the ability to securely, uniquely, and positively distinguish it from others of the same kind. This allows one to validate that items entered into an inspection regime to which the tag or seal is affixed are as claimed. We are developing a new type of unique identifier (UID) for such applications that is based on fiber-Bragg grating (FBG) technology. The index of refraction of the core glass of a fiber optic can be locally and permanently altered if sensitized fibers are exposed to intense ultraviolet light. This can be used to create index modulations with a regular periodicity comparable to the wavelengths of light with which the fiber is used. If broadband illumination is sent down the fiber, any light that is in resonance with the modulations will be reflected back to the input end of the fiber where it can be detected. The shape of the returned spectrum can be set by the modulation pattern written into the fiber’s core. We take advantage of these properties to create a compact UID that contains several FBGs potted into a monolithic body. By connecting the UID to an optical interrogator, the complex spectral return can be uniquely identified with a short measurement, providing a robust identification. As a device based on narrowband spectral returns, FBGs are inherently radiation tolerant, making them ideal for use with nuclear materials. Further, they can be read out remotely via a long fiber optic or locally via brief connection to a portable optical interrogator. Because the spectral signature of FBGs is sensitive to external mechanical perturbations, we are exploring the ability to reversibly alter the signature obtained from the UID by applying controlled mechanical forces with a simple device. Such a “key” will allow different stakeholders to obtain their own unique signature from the device, providing a new level of surety to safeguards inspections.

Ziock, Klaus-Peter↗

DOE OSTI2022

Functional high-performance fiber structure

A method is provided for growing a fiber structure, where the method includes: obtaining a substrate, growing an array of pedestal fibers on the substrate, growing fibers on the pedestal fibers, and depositing a coating surrounding each of the fibers. In another aspect, a method of fabricating a fiber structure includes obtaining a substrate and growing a plurality of fibers on the substrate according to 1½D printing. In another aspect, a multilayer functional fiber is provided produced by, for instance, the above-noted methods.

Pegna, Joseph↗