Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

A feasibility study of heat-pipe-cooled leading edges for hypersonic cruise aircraft

A theoretical study of the use of heat pipe structures for cooling the leading edges of hypersonic cruise aircraft was carried out over a Mach number range of 6 to 12. Preliminary design studies showed that a heat pipe cooling structure with a 33-in. chordwise length could maintain the maximum temperature of a 65 deg sweepback wing with a 0.5-in. leading edge radius below 1600 F during cruise at Mach 8. A few relatively minor changes in the steady-state design of the structure were found necessary to insure satisfactory cooling during the climb to cruise speed and altitude. It was concluded that heat pipe cooling is an attractive, feasible technique for limiting leading edge temperatures of hypersonic cruise aircraft.

Silverstein, C. C.↗
NASA NTRS1972

Effects of leading-edge camber on low-speed characteristics of slender delta wings

Wind-tunnel studies have been conducted to determine the effects of leading-edge camber on the low-speed aerodynamic characteristics of a thin, sharp-edge 74 deg delta wing. The results include force and moment measurements, pressure distributions, and flow visualization patterns determined from oil flow, tuft and water vapor observations. The study indicated that leading-edge camber near the apex is effective in controlling the pitch-up tendency of slender delta wings.

Wentz, W. H., Jr.↗
NASA NTRS1972

Flow conditions around the exit and downstream of certain stator blading with various trailing edge thicknesses and geometries

The blading investigated was curved back with thick profiles. The variations in flow conditions considered were flow angle and isentropic energy. Experimental data were obtained in a two-dimensional cascade from surveys with a combined angle, total-, and static-pressure probe and from an array of end-wall static pressure taps. Analytical results were obtained from ideal flow theory. The results showed large variations in flow conditions close to the plane of the trailing edge that were largely attenuated at a distance a little greater than one blade pitch downstream of the trailing edge in the direction of flow. The results were affected by the geometry and thickness of the trailing edge. The agreement between experimental and analytical results is generally fair to excellent.

Prust, H. W., Jr.↗
NASA NTRS1973

The problem of edge cracks in an infinite strip

The elastostatic plane problem of an infinite strip containing two symmetrically located internal cracks perpendicular to the boundary is formulated in terms of a singular integraL equation with the derivative of the crack surface displacement as the density function. The solution of the problem is obtained for various crack geometries and for uniaxial tension applied to the strip away from the crack region. The limiting case of the edge cracks is then considered in some detail. The fundamental function of the integral equation is obtained and a numerical technique for solving the singular integral equations with this particular type of fundamental function which is characteristic of the edge cracks is described. The stress intensity factor for the complete range of net ligament-to-width ratio is calculated. The results also include the solution of the edge crack problem in an elastic half plane.

Gupta, G. D.↗
NASA NTRS1973

Wind tunnel investigation of effects of variations in Reynolds number and leading-edge treatment on the aerodynamic characteristics of an externally blown jet-flap configuration

An investigation has been conducted in a full-scale tunnel to determine the effects of variations in Reynolds number and leading-edge treatment on the aerodynamic characteristics of an externally blown jet-flap transport configuration. The model had a double-slotted trailing-edge flap and was powered by four high-bypass-ratio turbofan engines. Tests were performed by using each of three leading-edge devices (a 30-percent-chord flap and 15- and 25-percent-chord slats) at Reynolds numbers from 0.47 x one million to 1.36 x one million thrust coefficients up to 3.5. The use of a 25-percent-chord slat was found to be more effective than a 15-percent-chord slat or a 30-percent-chord flap in extending the stall angle of attack and in minimizing the loss of lift after the stall. The large slat was also effective in reducing the rolling moments that occurred when the engine-out wing stalled first.

Parlett, L. P.↗
NASA NTRS1973

The effects of leading-edge serrations on reducing flow unsteadiness about airfoils.

High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 x 1,000,000 to 6.2 x 1,000,000 on a rectangular wing of NACA 63-009 airfoil section. A wide selection of leading-edge serrations were also added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large peak in rms pressure, which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related mathematically to the airfoil trailing-edge and boundary-layer thicknesses.

Schwind, R. G.↗
NASA NTRS1972

Leading-edge force features of the aerodynamic finite element method.

Description of a practical procedure for computing the wing leading-edge thrust distribution by the finite element method. When incorporated into a wing-body aerodynamic computer program, the technique is capable of predicting (at subsonic and supersonic speeds) the leading-edge thrust distribution (and therefore, the lateral-directional stability derivatives due to roll) and the nonlinear aerodynamic characteristics of low aspect-ratio wings with leading edge separation due to the application of suction technology.

Lan, C.-T.↗
NASA NTRS1973

Vibration and local edge buckling of thermally stressed, wedge airfoil cantilever wings.

The local edge buckling phenomena that can occur along the heated thin edge of a wedge shape airfoil is calculated. Qualitative comparison (qualitative only because the experimental temperature distribution was not measured) is made to the experimentally observed phenomena. The consequences of the assumption of identical vibration and buckling modes is shown by a comparison of results with and without the assumption of mode identity. Computer plots of the elastic surface as local buckling develops with increasing temperature are shown. The calculated, fully developed local edge buckling is compared to a photograph of a fully developed buckling as observed in the laboratory.

Bailey, C. D.↗
NASA NTRS1973

Four Space Shuttle wing leading edge concepts.

A heat-pipe-cooled Space Shuttle orbiter wing leading edge was compared and evaluated against three alternate leading edge candidates: a refurbishable ablative design, and two other reusable versions employing coated columbium and carbon-carbon high-temperature segments. Each candidate concept was shown feasible in the Phase B environment. The reusable versions were all found to cost nearly the same and substantially less than the nonreusable ablative version. However, since current Shuttle trajectories produce higher heating rates than those used in this study, the carbon-carbon and heat pipe concepts are now the prime candidates for Shuttle leading edge thermal protection.

Niblock, G. A.↗
NASA NTRS1973

The effects of leading-edge serrations on reducing flow unsteadiness about airfoils, an experimental and analytical investigation

High frequency surface pressure measurements were obtained from wind-tunnel tests over the Reynolds number range 1.2 times one million to 6.2 times one million on a rectangular wing of NACA 63-009 airfoil section. Measurements were also obtained with a wide selection of leading-edge serrations added to the basic airfoil. Under a two-dimensional laminar bubble very close to the leading edge of the basic airfoil there is a large apatial peak in rms pressure. Frequency analysis of the pressure signals in this region show a large, high-frequency energy peak which is interpreted as an oscillation in size and position of the bubble. The serrations divide the bubble into segments and reduce the peak rms pressures. A low Reynolds number flow visualization test on a hydrofoil in water was also conducted. A von Karman vortex street was found trailing from the rear of the foil. Its frequency is at a much lower Strouhal number than in the high Reynolds number experiment, and is related to the trailing-edge and boundary-layer thicknesses.

Schwind, R. G.↗
NASA NTRS1973

Analysis of the Flow About Delta Wings with Leading Edge Separation at Supersonic Speeds

A research program was conducted to develop an improved theoretical flow model for the flow about sharp edge delta wings with leading-edge separation at supersonic speeds. The flow model incorporates a representation of the secondary separation region which occurs just inboard of the leading edge on such wings and is based on a slender-wing theory whereby the full three-dimensional problem is reduced to a quasi two-dimensional problem in the cross-flow plane. The secondary separation region was modeled by a surface distribution of singularities or a linearized type of cavity representation. The primary vortex and separation were modeled by a concentrated vortex and cut in the cross-flow potential which represents its feeding sheet. The cross-flow solutions for the cavity model were obtained, but these solutions have physical significance only in a very restricted range of angle of attack. The reasons for the failure of the flow model are discussed. The analysis is presented so that other interested researchers may critically review the work.

Nenni, J. P.↗
NASA NTRS1974

An experimental investigation of leading-edge vortex augmentation by blowing

A wind tunnel test was conducted to determine the effects of over-the-wing blowing as a means of augmenting the leading-edge vortex flow of several pointed-tip, sharp-edged planforms. Arrow, delta, and diamond wings with leading-edge sweeps of 30 and 45 degrees were mounted on a body-of-revolution fuselage and tested in a low-speed wind tunnel at a Mach number of 0.2. Nozzle location data, pitch data, and flow-visualization pictures were obtained for a range of blowing rates. Results show pronounced increases in vortex lift due to the blowing.

Bradley, R. G.↗
NASA NTRS1974

A quantitative study of the orientation bias of some edge detector schemes

The evaluation of a particular set of edge detection schemes is described. The results obtained are compared with those obtained from an edge detection scheme using a texture oriented approach. The orientational bias of these schemes is emphasized. Improved qualitative observations are reported and a comparison of the evaluation method with another edge detection evaluation method is presented.

Fram, J. R.↗
NASA NTRS1974

Pressure measurements on the leading edge of a swept wing at Mach 2.2

Detailed pressure measurements were made on a flat semispan swept wing with a rounded leading edge at Mach number 2.2 through a range of Reynolds numbers. Pressure orifices were distributed in the streamwise direction at five spanwise stations on the leading edge and on the upper and lower surfaces. No significant amount of leading-edge suction was found, but the pressures and integrated normal forces on the upper and lower surfaces indicate the presence of a vortex lift.

Sorrells, R. B., III↗
NASA NTRS1974

Low-speed aerodynamic characteristics of airfoil sections with rounded trailing edges in forward and reverse flow

Low-speed wind-tunnel tests were conducted to determine the two-dimensional aerodynamic characteristics of 6-, 12-, and 18-percent-thick airfoil sections with rounded trailing edges in both forward and reverse flow. The shapes incorporated camber with both the leading and trailing edges rounded to provide reasonable aerodynamic performance with either edge directed toward the free-stream flow. The tests were conducted with the airfoils in both normal and reverse orientations relative to the free stream. The Mach number was varied from 0.16 to 0.36 and the angle of attack was varied from minus 10 to 24 million. Reynolds number, based on the airfoil chord, was varied from about 1.0 to 12.0 million.

Beasley, W. D.↗
NASA NTRS1974

Effects of leading edge sweep angle and design lift coefficient on performance of a modified arrow wing at a design Mach number of 2.6

Wing models were tested in the high-speed section of the Langley Unitary Plan wind tunnel to study the effects of the leading-edge sweep angle and the design lift coefficient on aerodynamic performance and efficiency. The models had leading-edge sweep angles of 69.44 deg, 72.65 deg, and 75.96 deg which correspond to values of the design Mach-number-sweep-angle parameter (beta cotangent A) sub DES of 0.6, 0.75, and 0.9, respectively. For each sweep angle, camber surfaces having design lift coefficients of 0,0.08, and 0.12 at a design Mach number of 2.6 were generated. The wind-tunnel tests were conducted at Mach numbers of 2.3, 2.6, and 2.96 with a stagnation temperature of 338.7 K (150 F) and a Reynolds number per meter of 9.843 times 10 to the 6th power. The results of the tests showed that only a moderate sweeping of the wing leading edge aft of the Mach line along with a small-to-moderate amount of camber and twist was needed to significantly improve the zero-lift (flat camber surface) wing performance and efficiency.

Mack, R. J.↗
NASA NTRS1975

Wind tunnel investigation of the wake near the trailing edge of a distributed upper-surface-blown flap

An investigation of the flow field near the trailing edge of a distributed upper-surface-blown propulsive-lift transport was conducted in the Langley V/STOL tunnel. This model used blowing slots across the entire wing span to produce a thin jet efflux near the leading edge and at the knee of the flap. Velocity surveys of the flow field were taken near the trailing edge of the model, and are presented as plots of the individual velocity vectors. The test conditions include an angle-of-attack range from 4 deg to 16 deg and a thrust coefficient range from 0 to 1.3 at a free-stream dynamic pressure of 814 Newton per square meter (17 pounds per square foot).

Forsyth, D. R.↗
NASA NTRS1975

Experimental evaluation of joint designs for a space-shuttle orbiter ablative leading edge

The thermal performance of two types of ablative leading-edge joints for a space-shuttle orbiter were tested and evaluated. Chordwise joints between ablative leading-edge segments, and spanwise joints between ablative leading-edge segments and reusable surface insulation tiles were exposed to simulated shuttle heating environments. The data show that the thermal performance of models with chordwise joints to be as good as jointless models in simulated ascent-heating and orbital cold-soak environments. The suggestion is made for additional work on the joint seals, and, in particular, on the effects of heat-induced seal-material surface irregularities on the local flow.

Tompkins, S. S.↗