SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Soluble copolymer binder mixed with cathode material and solvent forms flexible porous cathode used in lithium and Ni/Cd batteries. Cathodes prepared by this process have lower density due to expanding rubbery binder and greater flexibility than conventional cathodes. Fabrication procedure readily adaptable to scaled-up processes.
A high rate active Li/SOCl2 cell was designed for use in a 28 volt, 250 amp-hour space battery system. The lithium battery is being considered as a replacement of its heavier silver-zinc counterpart on board the Centaur-G booster rocket which is used to launch payloads from the Space Shuttle cargo bay into deep-space. Basically a feasibility study, this development effort is demonstrating the ability of the lithium cell to deliver up to 90 amps safely at power densities of approximately 25 watts per pound. Test data on 4 prototype units is showing an energy density of 85 watt-hours per pound and 9.0 watt-hours/cu in. The cells tested typically delivered 280 to 300 amp-hours under ambient temperature test conditions using alternating continuous loads of 90, 55, and 20 amperes throughout life. Data from four cells tested are presented to demonstrate the capability of Li/SOCl2 technology for a C/3 discharge rate in active and hermetic cell units.
Traditional liquid electrolytes used in lithium (Li) metal batteries (LMBs) have severe safety issues, poor power density, as well as thermal and electrochemical instability that prevents their scaling to newer applications, such as electric vehicles. Using sulfide-based solid-state electrolytes (SSEs) is a viable method to address many of the issues that plague LMBs. However, the key issue preventing the expansion of sulfide-based SSEs is an interplay between poor interfacial stability with the electrodes and massive external stack pressure required to maintain electrode-electrolyte contact. The need for extensive pressure requires large system-level (i.e., battery pack used in an electric vehicle) housing that causes a disconnect between performance at a smaller scale and actual application. Secondary prevention to sulfide-based SSE adoption are difficulties in manufacturing, as toxic deterioration occurs when these materials are exposed to humidity, as well as drastic reduction in SSE performance at low temperature. This work hypothesizes that unique interfacial designs of electrodes and the modification of the sulfide-based SSE will enable reduction of necessary external cell pressure, and therefore support the design of practical LMBs. This will be done through collaboration within Idaho National Laboratory (INL), where manufacturing practices will be parameterized to produce low defect, low porosity SSEs with slight modifications. Next, artificial interfaces will be produced on electrodes to observe the conformality and mass transport properties between the modified SSE and pre-treated anode. External pressure on Li-metal cells will also be parameterized to reduce interfacial impedance while a reduction in the pressure will allot reasonable housing design for larger scale applications. Focus on novelty in this work occurs by modifications to the solid-solid interfaces between electrolyte and electrode, done through doping of the electrolyte and production of artificial interfaces on the Li-metal anode. The modifications at these interfaces, in addition to modified external pressure could identify and address the poor interfacial impedance that hinders high performance SSEs. Fundamental understanding on how to reduce the key hindrances of all-solid-state batteries (ASSBs) will support the advancement for larger scale production and performance, of which will be held in perspective for future works. Beyond battery development, the knowledge gained from process control and defect analysis is applicable to other ceramic systems, such as nuclear fuel coatings and high temperature electrolyzers.
Traditional liquid electrolytes used in lithium (Li) metal batteries (LMBs) have severe safety issues, poor power density, as well as thermal and electrochemical instability that prevents their scaling to newer applications, such as electric vehicles. Using sulfide-based solid-state electrolytes (SSEs) is a viable method to address many of the issues that plague LMBs. However, the key issue preventing the expansion of sulfide-based SSEs is an interplay between poor interfacial stability with the electrodes and massive external stack pressure required to maintain electrode-electrolyte contact. The need for extensive pressure requires large system-level (i.e., battery pack used in an electric vehicle) housing that causes a disconnect between performance at a smaller scale and actual application. Secondary prevention to sulfide-based SSE adoption are difficulties in manufacturing, as toxic deterioration occurs when these materials are exposed to humidity, as well as drastic reduction in SSE performance at low temperature. This work hypothesizes that unique interfacial designs of electrodes and the modification of the sulfide-based SSE will enable reduction of necessary external cell pressure, and therefore support the design of practical LMBs. This will be done through collaboration within Idaho National Laboratory (INL), where manufacturing practices will be parameterized to produce low defect, low porosity SSEs with slight modifications. Next, artificial interfaces will be produced on electrodes to observe the conformality and mass transport properties between the modified SSE and pre-treated anode. External pressure on Li-metal cells will also be parameterized to reduce interfacial impedance while a reduction in the pressure will allot reasonable housing design for larger scale applications. Focus on novelty in this work occurs by modifications to the solid-solid interfaces between electrolyte and electrode, done through doping of the electrolyte and production of artificial interfaces on the Li-metal anode. The modifications at these interfaces, in addition to modified external pressure could identify and address the poor interfacial impedance that hinders high performance SSEs. Fundamental understanding on how to reduce the key hindrances of all-solid-state batteries (ASSBs) will support the advancement for larger scale production and performance, of which will be held in perspective for future works. Beyond battery development, the knowledge gained from process control and defect analysis is applicable to other ceramic systems, such as nuclear fuel coatings and high temperature electrolyzers.
Future lithium batteries are expected to use solid electrolytes to achieve higher energy density and fast charge capabilities. However, most solid electrolytes are thermodynamically unstable against layered oxide cathodes. In this study, the stability of LiCoO2 (LCO) cathode with Li10GeP2S12 (LGPS) solid electrolyte is investigated using ab initio molecular dynamics (AIMD) and machine learning molecular dynamics (MLMD). The propensity of ionic interdiffusion, formation of a passivating interphase layer, and corresponding decay in cell performance is addressed using a continuum model. Large-scale MLMD simulations confirm that the LCO|LGPS interface permits interdiffusion of cobalt (Co) and other ionic species, leading to the formation and growth of a resistive interphase and to dramatic capacity fade even in the first cycle. We examine the literature evidence that incorporating a thin layer of LiNb0.5Ta0.5O3 (LNTO) between LCO and LGPS prevents the interdiffusion of ions. Atomistic simulations suggest that substituting lithium (Li) in LNTO with Co is thermodynamically unfavorable, thereby inhibiting ionic interdiffusion. The stable Nb5+/Ta5+ states form a rigid metal-oxide framework, which consequently also prevents the substitution of niobium (Nb) or tantalum (Ta). However, continuum-level analysis suggests that the higher mechanical stiffness of LNTO can lead to interfacial delamination between the LCO and LNTO. This phenomenon reduces the effectiveness of the protective layer. This paper, therefore, highlights the need to develop novel interlayers that balance low ionic interdiffusion with low mechanical stiffness.
The development of advanced lithium-metal batteries (LMBs), such as high-temperature LMBs and high-energy-density LMBs, has critical requirements for electrolytes. However, conventional electrolytes suffer from thermal instability and insufficient electrolyte/Li interfacial compatibility, severely limiting their utilization in high-temperature LMBs. Herein, we design a high-temperature N-methylacetamide (NMAc)-based deep eutectic electrolyte (DEE) by molecular engineering on a solvation structure via a sacrificial additive of vinyl ethylene carbonate (VEC). Specifically, VEC interacts with the Li prior to NMAc, facilitating the formation of a solid electrolyte interphase to inhibit the reaction between Li and NMAc. The stable VEC-DEE effectively suppresses the growth of lithium dendrites and ensures the battery a cycling stability of 550 cycles at 80 °C. Additionally, we also demonstrate the application of VEC-DEE in high-energy-density LMBs with a high mass loading of 2.5 mAh/cm 2 . In conclusion, this research opens a new avenue for the rational design of advanced high-temperature electrolytes.
Abstract Soft polymeric Janus nanoparticles (JNPs), made from polystyrene‐ b ‐poly(butadiene)‐ b ‐poly(methylmethacrylate), PS‐PB‐PMMA, triblock terpolymers, assemble into a monolayer at the water–oil interface to reduce interfacial tension. The extent to which the polymer chains can deform influences the packing density of the JNPs at the interface. The longer the polymer chains are relative to the core, the softer are the JNPs, resulting in a JNPs assembly with a lower initial lateral packing density. The interfacial activity of JNPs can be further tuned by complexation of the PMMA chains with lithium ions that are introduced into the water phase. This work provides a fundamental understanding of soft JNPs packing at the water–oil interface and provides a strategy to tailor the areal density of soft JNPs at liquid–liquid interface, enabling the design of smart responsive structured‐liquid systems.
Abstract Soft polymeric Janus nanoparticles (JNPs), made from polystyrene‐ b ‐poly(butadiene)‐ b ‐poly(methylmethacrylate), PS‐PB‐PMMA, triblock terpolymers, assemble into a monolayer at the water–oil interface to reduce interfacial tension. The extent to which the polymer chains can deform influences the packing density of the JNPs at the interface. The longer the polymer chains are relative to the core, the softer are the JNPs, resulting in a JNPs assembly with a lower initial lateral packing density. The interfacial activity of JNPs can be further tuned by complexation of the PMMA chains with lithium ions that are introduced into the water phase. This work provides a fundamental understanding of soft JNPs packing at the water–oil interface and provides a strategy to tailor the areal density of soft JNPs at liquid–liquid interface, enabling the design of smart responsive structured‐liquid systems.
Next-generation lithium-ion batteries are expected to use solid electrolytes (SEs) to enable higher energy density and extreme fast-charge capabilities. One major mode of degradation at the cathode|SE interface is delamination between the cathode active materials and SEs, which leads to performance decay. Experimental observations indicate that implementation of interphase layers can minimize the cathode|SE delamination induced capacity fade. A multiscale computational methodology is developed here to investigate the applicability of boron substituted lithium carbonate (Li 2+x B x C 1–x O 3 , x = 0.5, or LBCO) to minimize the delamination at the cathode|SE interface. Atomistic simulations indicate that the fracture energies at both the cathode|LBCO and LBCO|SE interfaces are higher than those at the cathode|SE interface, which reduces the extent of delamination. Mesoscale simulations indicate that, apart from increasing the fracture energy, decreasing the evolution of strain energy by lowering the elastic modulus of the interphase layer can also minimize the extent of delamination at the cathode|SE interface. However, the adoption of an interphase layer with high ionic conductivity is necessary to minimize the ohmic losses during operation at higher current densities. This study provides guidance on selecting interphase layers with specific properties and thicknesses to minimize both interfacial delamination and impedance growth.
Li metal anodes are a critical battery technology due to their ability to substantially increase the energy density of Li-based batteries. It is well known that pressure greatly impacts the performance of a Li-metal anode. However, precisely how the pressure value and distribution of pressure affect performance is unclear. Furthermore, the solid-electrolyte interphase composition that forms under varying pressure distributions remains a key parameter for practical lithium metal anodes. In this work, different pressure distributions were employed by using differently shaped and oriented mechanical springs in the coin cells, resulting in varying contact points. Pressure-sensitive films were used to spatially map the pressure and correlate it to the performance. It was found that higher average pressure does not necessarily have a positive effect on performance. When high pressure is paired with poor pressure uniformity, the performance is in fact worse likely due to the current focusing effect, rendering unsatisfied cycling stability. This work points to the importance of controlling the relationship between average pressure and pressure uniformity.
Electrode and electrolyte studies for lithium- copper fluoride batteries
Al-Li alloys offer the benefits of increased strength, elastic modulus and lower densities as compared to conventional aluminum alloys. Martin Marietta Laboratories has developed an Al-Li alloy designated 2195 which is designated for use in the cryogenic tanks of the space shuttle. The Variable Polarity Plasma Arc (VPPA) welding process is currently being used to produce these welds [1]. VPPA welding utilizes high temperature ionized gas (plasma) to transfer heat to the workpiece. An inert gas, such as Helium, is used to shield the active welding zone to prevent contamination of the molten base metal with surrounding reactive atmospheric gases. [1] In the Space Shuttle application, two passes of the arc are used to complete a butt-type weld. The pressure of the plasma stream is increased during the first pass to force the arc entirely through the material, a practice commonly referred to as keyholing. Molten metal forms on either side of the arc and surface tension draws this liquid together as the arc passes. 2319 Al alloy filler material may also be fed into the weld zone during this pass. During the second pass, the plasma stream pressure is reduced such that only partial penetration of the base material is obtained. Al 2319 filler material is added during this pass to yield a uniform, fully filled welded joint. This additional pass also acts to alter the grain structure of the weld zone to yield a higher strength joint.
The energy crisis and environmental pollution require the advancement of large-scale energy storage techniques. Among the various commercialized technologies, batteries have attracted enormous attention due to their relatively high energy density and long cycle life. Nevertheless, the limited supply and uneven distribution of lithium minerals, as well as their high cost, has greatly hindered the application of lithium-ion batteries in large-scale energy storage. Therefore, building next-generation alternative rechargeable batteries that feature low cost, long service life, and high safety is of the utmost importance. Over the past several years, we have witnessed many successful research outcomes for sodium and potassium ion batteries (SIBs and PIBs) in regard to electrode and electrolyte materials. In this Perspective, we summarize the current developments on SIBs/PIBs and their challenges when facing practical applications, including their cost, energy density, ion diffusivity in solids/electrolytes/interphases, cycle life, and safety concerns. Furthermore, we provide an overview of strategies to overcome the remaining challenges for achieving better electrochemical performance. Finally, we outline several possible directions for the future development of these two battery chemistries, with the hope of aiding the transition from the laboratory to next-generation practical applications for SIBs/PIBs batteries in grid-scale energy storage.
Sodium-ion batteries have garnered unprecedented attention as an electrochemical energy storage technology, but it remains challenging to design high-energy-density cathode materials with low structural strain during the dynamic (de)sodiation processes. In this paper, we report a P2-layered lithium dual-site-substituted Na 0.7 Li 0.03 [Mg 0.15 Li 0.07 Mn 0.75 ]O 2 (NMLMO) cathode material, in which Li ions occupy both transition-metal (TM) and alkali-metal (AM) sites. The combination of theoretical calculations and experimental characterizations reveals that Li TM creates Na–O–Li electronic configurations to boost the capacity derived from the oxygen anionic redox, while Li AM serves as LiO 6 prismatic pillars to stabilize the layered structure through suppressing the detrimental phase transitions. As a result, NMLMO delivers a high specific capacity of 266 mAh g –1 and simultaneously exhibits the nearly zero-strain characteristic within a wide voltage range of 1.5–4.6 V. Our findings highlight the effective way of dual-site substitution to break the capacity–stability trade-off in cathode materials for advanced rechargeable batteries.
We demonstrate a first-principles screening methodology as an effective tool to explore electrolyte formulations for the new generation of high energy density rechargeable batteries. We study the liquid structure and electronic properties in dilute electrolytes, high concentration electrolytes (HCE), and localized high concentration electrolytes (LHCE), with focus on electrolyte formulations based on lithium bis(fluorosulfonyl)imide (LiFSI), dimethyl carbonate (DMC), and bis(2,2,2-trifluoroethyl) ether (BTFE) as a diluent. We describe the solvation complexes in the dilute electrolyte and explore structural changes triggered by the increase in lithium salt concentration for HCEs and the diluent effects in LHCEs. In HCE formulations, there is a 4-fold coordination environment of lithium-ions as in the dilute electrolyte, but the number of lithium-ion interactions with O atoms from FSI- anions dominates. In these solutions, the ability of the FSI- anions to interact with multiple lithium-ions allows complex 3D network formation and influences the reductive/oxidative behavior of the electrolyte. Interestingly, in LHCEs, the BTFE diluent molecules do not change the 3D solution structure when diluting the HCE formulation from 5.49 to 3.83 M. However, there is a composition threshold where the structural and electronic behavior may change. We show that diluting the HCE electrolyte with BTFE down to 1.77 M breaks the three-dimensional solution structure into an island-like solvation complex. We relate these structural changes to the electronic properties of the electrolytes finding a causal relationship between the reductive/oxidative behavior and the lithium-oxygen interaction mechanisms in the solvated complexes. The coordination with lithium-ions lowers the electrolyte LUMO and HOMO levels: the higher is the number of interactions with lithium-ions, the more likely the solvent molecule, FSI- anion, or diluent molecule is to be reduced and the less likely it is to become oxidized. The evolution of the solvated ion structure in HCE and LHCE suggests a close connection to a corresponding change in the lithium-ion transport mechanisms for these electrolytes.
During the AMPTE (Active Magnetospheric Particle Tracer Explorers) solar wind lithium release on September 11, and again on September 20, 1984, an intense burst of electrostatic noise was observed near the upstream edge of the ion cloud. Comparisons with measurements by the IMP-6 and ISEE-1 spacecraft show that the spectrum and overall features of this noise are very similar to electrostatic noise observed at the Earth's bow shock. A stability analysis using realistic parameters shows that the electrostatic noise can be accounted for by an ion beam-plasma instability caused by the solar wind proton beam streaming through the nearly stationary lithium cloud. The growth rate of this instability is largest when the ion density and solar wind proton density are similar, which explains why the noise only occurs near the outer edge of the ion cloud. The similarity to the noise in the Earth's bow shock suggest that a shock may exist in the solar wind plasma flow upstream of the ion cloud. If the noise is associated with a shock, then it must be an electrostatic shock, since the ion cyclotron radii are too small for the existence of a MHD shock. Since the electrostatic instability occurs at phase velocities near the lithium thermal velocity, the electrostatic turbulence may play a role in heating the lithium ions and transferring momentum from the solar wind to the ion cloud.
Large-scale production of vertically aligned single-walled carbon nanotubes (VA-SWCNTs) on metal foils promises to enable technological advancements in many fields, from functional composites to energy storage to thermal interfaces. In this work, we demonstrate growth of high-quality (G/D > 6, average diameters ~ 2–3 nm, densities > 10 12 cm –2 ) VA-SWCNTs on Inconel metal for use as a lithium-ion battery (LIB) anode. Scale-up of SWCNT growth on Inconel 625 to 100 cm 2 exhibits nearly invariant CNT structural properties, even when synthesis is performed near atmospheric pressure, and this robustness is attributed to a growth kinetic regime dominated by the carbon precursor diffusion in the bulk gas mixture. SWCNT forests produced on large-area metal substrates at close to atmospheric pressure possess a combination of structural features that are among the best demonstrated so far in the literature for growth on metal foils. Leveraging these achievements for energy applications, we demonstrate a VA-SWCNT LIB anode with capacity >1200 mAh/g at 1.0C and stable cycling beyond 300 cycles. Furthermore, this robust synthesis of high-quality VA-SWCNTs on metal foils presents a promising route toward mass production of high-performance CNT devices for a broad range of applications.
Bronze and bronze-derived, mixed metal oxides are materials of growing interest for lithium-ion battery anodes due to their high-rate capabilities and the potential for high energy densities via multielectron redox. We report on the synthesis and electrochemical properties of the tetragonal tungsten bronzetype phase Nb 8 W 9 O 47 and our investigation into the structural evolution of this phase upon lithium (de)intercalation, with particular attention to how it relates to the fast-cycling capabilities. Electrochemical cycling shows Nb 8 W 9 O 47 can achieve greater than one Li + per transition metal at rates of C/2 or slower and maintains a capacity equivalent to 0.65 Li + per transition metal at a rate of 20C. Sequential Rietveld analysis of operando X-ray diffraction data reveals anisotropic changes to the unit cell parameters during discharge, accompanied by an off-centering of the transition metals within their octahedral environments. While higher capacities can be accessed below 1.2 V, cells discharged to 1.0 V exhibit a significant expansion of the unit cell volume and reduced Coulombic efficiencies. This report suggests that rigid crystal structures incapable of undergoing polyhedral rotational deformations can instead exploit displacive distortions of the transition metal redox center to enable fast Li-ion cycling with minimal atomic rearrangements.