Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “computed Tomography”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Physical model and experimental validation of a high temperature proton exchange membrane electrochemical hydrogen pump cell for efficient single-stage extraction of low concentration hydrogen gas

There is interest in valorization of existing natural gas infrastructure to facilitate the co-transportation of hydrogen via blending of hydrogen gas initially at limited concentrations of 1–20 vol% H2 and to subsequently extract hydrogen at fuel cell quality standards (SAE J2719/ISO14687-2). High temperature proton exchange membrane electrochemical hydrogen pump (HT-PEM EHP) based on phosphoric acid doped polybenzimidazole (PA-PBI) exhibits good performance at elevated temperatures (>120 °C), which provides desirable tolerance to non-methane natural gas constituents that are problematic for lower temperature based EHP. To better understand the suitability of the HT-PEM EHP for such gas separation processes, a two-dimensional model of EHP based on PA-PBI was developed. The model is validated for several relevant operating conditions and across cells with differing amounts of phosphoric acid content in the electrodes. Operando micro x-ray computed tomography (CT) imaging of an HT-PEM EHP was used to further validate physical parameters and assumptions of the model. The impacts of pressure, relative humidity of the anode feed, and concentration of feed gases on separation performance are investigated. This study shows that a specific energy of separation of 5.1 kWh/kg H2 at a hydrogen recovery factor (HRF) of 50 vol% can be achieved in a single stage with the EHP, producing fuel cell quality hydrogen purity of 99.99 vol% H2 from a 2 vol% H2/CH4 feed blend, while pressurizing the product H2 at a pressure ratio of 1.3 relative to feed pressure.

Stansberry, John M↗
DOE OSTI2021

Mechanisms dominating thixotropy in limestone calcined clay cement (LC3)

Limestone calcined clay cement (LC3) is a green binder with great practical importance for the cement industry. Growing application has increased the need to understand the mechanisms governing its thixotropy for better control of workability. While formation of C-S-H bridges is understood to dominate the thixotropy of ordinary Portland cement, LC3 paste displayed unique thixotropy properties. In this study, focused beam reflectance measurement, zeta potential, 1H nuclear magnetic resonance relaxometry and micro X-ray computed tomography were used to track the colloidal interaction and hydration extent within LC3 paste. Results showed that flocculation due to the negative surface charge and water affinity of calcined clay appears to be the dominating factor. This leads to a reduction of water available to contribute to fluidity of the paste and, in turn, governing the development of thixotropy over time. In addition, the dilution effect due to high clinker substitution diminishes thixotropy growth with time.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-situ X-ray and visual observation of foam morphology and behavior at the batch-melt interface during melting of simulated waste glass

We report to attain a basic understanding of the primary foam structure and behavior, which affects the heat and mass transfer and the efficiency of the glass melting process, we investigated the primary foam layer under the glass batch floating on molten glass. The primary foam affects mass transfer during batch melting, in turn affecting the melting process. The recently performed direct in-situ three-dimensional X-ray computed tomography of the batch melting in a laboratory-scale melter vessel allowed us to visualize the features of the reacting batch layer and the foam that develops at its bottom, though with an insufficient resolution of images. In this study, we obtained better temporal and spatial resolution using the two-dimensional X-ray radiography and visual observation of the structure and behavior of transient primary foam as it formed and decayed. As soon as the batch was charged onto the melt surface, foam bubbles began to evolve, grow, and coalesce, forming a primary foam layer, 5-10 mm thick, within tens of seconds. This foam layer was sustained by ongoing gas evolving reactions counterbalanced by bubble coalescence into cavities that moved sideways and escaped to the atmosphere. Eventually, the entire remaining batch turned into foam that gradually decayed at the melt surface. The decay rate agreed with literature observations of surface foam produced by secondary foaming.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of a silicon carbide ceramic based counter-flow heat exchanger by binder jetting and liquid silicon infiltration for concentrating solar power

A silicon carbide ceramic counter-flow heat exchanger with integrated headers was printed by binder jetting additive manufacturing process. Multiple phenolic binder infiltration cycles (3 or 5) followed by pyrolysis were conducted to increase the net carbon content of the printed SiC specimens. Subsequently, to attain full densification, silicon melt infiltration was used. The microstructure and mechanical properties were comprehensively characterized on the densified material. The chemical compositions and visual distribution of the various regions in the specimens were determined via scanning electron microscopy, while X-ray diffraction and synchrotron µ-computed tomography were used to provide a quantitative assessment of the volume fractions of the identified phase regions. Microhardness measurements showed dependence on the local microstructure. The fracture strength of the material was correlated with the specimen density and agreed with the reported values in the literature. High-temperature exposure at 750 °C for up to 200h did not degrade the strength for the specimens with three phenolic-binder infiltrations; however, the strengths degraded for ones with five phenolic-binder infiltrations. The associated fracture toughnesses of the specimens were ~3.4 MPam 1/2 at room temperature and 750°C, and the thermal conductivities varied from >150 W/mK at room temperature to ~45 W/mK at 750°C. Hence, this study validated the use of the binder-jetting printed SiC ceramic materials for high-temperature heat exchanges. Lastly, we also present in this work the first successful fabrication of a binder-jetting printed one-piece dense SiC ceramic heat exchanger body with unblocked channels that can be used for the flow of heat transfer fluids.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling strength and failure variability due to porosity in additively manufactured metals

To model and quantify the variability in plasticity and failure of additively manufactured metals due to imperfections in their microstructure, we have developed uncertainty quantification methodology based on pseudo marginal likelihood and embedded variability techniques. We account for both the porosity resolvable in computed tomography scans of the initial material and the sub-threshold distribution of voids through a physically motivated model. Calibration of the model indicates that the sub-threshold population of defects dominates the yield and failure response. Finally, the technique also allows us to quantify the distribution of material parameters connected to microstructural variability created by the manufacturing process, and, thereby, make assessments of material quality and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Contrasting thermally-induced structural and microstructural evolution of alumino-silicates with tubular and planar arrangements: Case study of halloysite and kaolinite

Materials with the similar chemical structures but different morphological organization exhibit considerable differences in thermally induced chemo-morphological evolution. With recent advancements in multi-scale X-ray scattering measurements, it is now possible to non-invasively probe the structural and microstructural evolution of such materials. In this study, we investigate the chemo-morphological evolution of halloysite and contrast the results with those for kaolinite. Halloysite and kaolinite have tubular and planar morphologies, respectively. Both materials are alumino-silicates comprising silica tetrahedra (T) and alumina octahedra (O) organized in a TO structure. Four distinct stages in the structural evolution were identified. Stages I, II, III, and IV correspond to temperature ranges of 25 to 125 °C, 125 to 400 °C, 400 to 625 °C, and 625 to 875 °C. Major structural changes correspond to the removal of interlayer/adsorbed water in stage I, the existence of the halloysite structure without interlayer water in stage II, dehydroxylation of halloysite in stage III, and the conversion of ordered halloysite to amorphous meta-halloysite in stage IV. Additionally, heating halloysite up to 875 °C resulted in slight widening of the nanotubes, as the average pore radius increased from 6.4 nm to 6.6 nm. Heating also resulted in an increase of wall thickness of the nanotubes from ~120 nm (25 °C) to 161 nm (875 °C). The increase in the halloysite nanotube diameter was attributed to the expansion of the structure and an increase in the surface roughness. The pore sizes in halloysite nanotubes were also confirmed using N 2 adsorption-desorption and nano-X-ray computed tomography (nano-XCT) measurements. The interlayer basal spacing in halloysite changed from 9.8 Å to 7.2 Å after the removal of interlayer water. At temperatures in the range of 625 to 875 °C, heating halloysite causes a small widening of nanotube pores and a minor increase in the surface area. In contrast, the interlayer spacing in kaolinite collapses on heating which reduces the nanoscale porosity. Furthermore, these studies demonstrate the differences in the chemo-morphological evolution of alumino-silicates with tubular and planar morphologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Topological analysis of X-ray CT data for the recognition and trending of subtle changes in microstructure under material aging

X-ray computed tomography (CT) is an established non-destructive tool for 3D imaging of multiphasic composites. Numerous applications of X-ray CT in medical diagnosis and materials characterization have been reported, many involving field-specific innovations in the imaging technology itself. Yet, quantitative summarization to link image features to properties of interest has been rare. Here we address this issue by employing state-of-the-art technics in scalar field topology for the summarization of X-ray CT images of an example biphasic system. By varying processing-parameters we create different microstructures, evolve them through accelerated thermal aging, CT-image them pre- and post-aged, and demonstrate the ability of our image summarization method to systematically track process- and age-related changes, which can often be very subtle. A novel aspect of the algorithm involves recognition over multiple resolution levels, which provides deeper insight into the pattern relationship between grain-like features and their neighbors. The method is general, adaptable to diverse image reconstruction methods and materials systems, and particularly useful in applications where practical constraints on the sample-size limits the reliable use of more complex models, e.g., convolutional neural networks.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Influence of crystal structure on constitutive anisotropy of silica sand at particle-scale

In spite of recent advanced geotechnical research regarding the influence of particle-scale morphology and fabric on the constitutive behavior of silica sands, there is still no published literature that investigated the influence of crystal structure of sand particles on their constitutive behavior. The main constituent of silica sand particles is quartz mineral, which has a trigonal crystal system and hexagonal lattice. This paper investigates the influence of quartz crystal structure on the constitutive response of silica sand particles using 3D X-ray diffraction (3DXRD), synchrotron micro-computed tomography (SMT), and 3D finite element (FE) analysis. Here, unconfined uniaxial compression experiments on single particles of synthetic silica cubes exposed the notion of constitutive anisotropy caused by the crystal structure of quartz. Since the silica cubes have simple regular geometry (1 mm) 3 , they were loaded in different directions with respect to their crystal local planes. The crystal structure was also identified for a natural silica sand specimen composed of 2705 particles and loaded in confined uniaxial compression. Physical limitations of the experimental measurements made a strong case for the use of 3D FE analysis to study how the change in crystal local orientation of individual sand particles can fundamentally produce anisotropy in the constitutive response of natural sand specimens. The 3D FE analysis was validated to accurately model the crystal-based constitutive anisotropy in silica particles using the results of the silica cube experiments. The analysis was then executed on 3D FE meshes that closely matched the physical shape and fabric of the 2705 particles in the natural sand specimen. Both the experiments and 3D FE analysis showed that the crystal structure of quartz essentially causes a directional anisotropy in the constitutive behavior of silica particles.

58 GEOSCIENCES↗
DOE OSTI2025

Influence of Initial fabric and water-wetting on particle fracture and force chain evolution in natural silica sand

Particle fracture has a significant influence on the engineering behavior of granular materials. However, the combined influence of the initial fabric and wetting on particle fracture and force chain evolution in granular materials, particularly in sands, remains insufficiently explored in the current literature. Here, in this paper, one-dimensional (1D) confined compression experiments were conducted on dry and wet specimens, and particle-level fracture was captured using three-dimensional (3D) in-situ Synchrotron Micro-Computed Tomography (SMT). A quantitative assessment of particle fracture revealed that wet specimens, which have disturbed fabric, exhibited a higher fracture percentage in comparison to dry specimens. Complementary 3D finite element (FE) simulations were performed using dry and wet (only solid fabric was considered and the influence of pore water is not considered) sand assemblies to assess interparticle contact forces and particle-scale stress distributions within the specimens. Force chain analysis was subsequently conducted, encompassing quantification of interparticle forces, characterization of force network structures, and monitoring the dynamic evolution of force chains under different strain levels. The results show that the specimens with disturbed fabric led to a more dynamic and less persistent force network, more fabric instability, and thus more reorganization of force chain structures. In addition, the frequent rearrangement of the force network in the presence of water (with reduced inter-particle contact friction) likely exacerbates localized stress concentrations, promoting failure in previously unengaged or weakly connected particles. The results reported in this paper offer a new insight into how the initial fabric and wetting cause different fracture behavior. The findings can also pave the way for more in-depth future investigations into the mechanics governing particle fracture in granular assemblies.

Finite element analysis↗
DOE OSTI2021

Transverse impact by RCCs on S-glass and Kevlar® FRC strips

This study aims to isolate interactions between plies and tows and reveal fundamental physics involved in transverse impact on fiber-reinforced composite (FRC) structures. Composite strips were sectioned from large panels and characterized by optical photography, three-dimensional synchrotron X-ray computed tomography, and scanning electron microscopy (SEM). Each strip was impacted perpendicularly by a right circular cylinder (RCC) projectile at a velocity ranging from ~ 150 to 600 m/s. The global strip behavior, as well as localized deformation and failure of the strip near the projectile corner, were both captured by high-speed optical imaging. S-Glass FRC strips were observed to fail in tension ahead of the RCC projectiles’ flat surfaces while Kevlar® FRC strips fractured at the projectile corners. The concept of critical velocity region previously used for impact on yarns was introduced to define different failure modes of each composite strip type. The strip damage extent was found to increase with the impact velocity and reach the maximum at the upper limit of the critical velocity region. Above the critical velocity region, the damage extent decreased with impact velocity. Wave propagations and load histories in the composite strips during impact were quantified and compared with Smith’s theory. Finally, critical velocities of single fibers, yarns, and composite strips and ballistic limits of single-ply and multi-ply composite panels were compared to provide insight into the design of impact-resistant fabrics and composites.

42 ENGINEERING↗
DOE OSTI2021

Processing and mechanical characterization of short carbon fiber-reinforced epoxy composites for material extrusion additive manufacturing

Fiber-reinforced polymer composites have been extensively utilized in recent years as feedstock materials for material extrusion additive manufacturing (AM) processes to improve strength, stiffness, and functionality of printed parts over unfilled printed polymers. However, the widespread adoption of AM of fiber-reinforced polymer composites requires a deeper understanding of the process-structure-property relationships in printed components, and such relationships are not well understood yet. Fiber length is critically important to the mechanical performance of short fiber composites, but very few studies to-date have focused on how the fiber length distribution (FLD) evolves during processing of composite feedstocks and how this evolution affects printing behavior and mechanical properties in 3D-printed composites. Here, FLD is measured for carbon fiber reinforced epoxy composites over a wide range of ink compositions and shear mixing times, and the distributions are fit with a Weibull-type distribution function. The effects of FLD on the tradeoff between ink processability, ink rheology, printing behavior and mechanical properties are investigated. Furthermore, the effects of printing parameters (nozzle size and print speed) on mechanical anisotropy and fiber orientation distribution (FOD) in printed composites are explored. Mechanical properties of printed composites are characterized via 3 pt-flexural testing, and microstructure is investigated using optical and scanning electron microscopy (SEM), and x-ray computed tomography. Finally, the fitted Weibull parameters are fed into a composite model that incorporates FLD and FOD, and model predictions are found to be in excellent agreement with experimental observations.

3D printing↗
DOE OSTI2021

High-speed synchrotron X-ray phase-contrast imaging for evaluating microscale damage mechanisms and tracking cracking behaviors inside cross-ply GFRCs

In this study, we integrated the high-speed synchrotron X-ray phase-contrast imaging (PCI) with a modified Kolsky compression bar loading platform to visualize the dynamic failure processes of cross-ply glass fiber reinforced composites (GFRCs). Four S-2 glass/SC-15 composite specimens were prepared, having similar thicknesses but different stacking sequences, namely as [0 12 /90 12 ], [90 12 /0 12 ], [0 8 /90 8 /0 8 ], and [90 8 /0 8 /90 8 ]. Three-dimensional synchrotron X-ray computed tomography and scanning electron microscopy (SEM) were employed to examine the microstructures and quantify the fiber volume fractions. Each specimen was notched and subjected to a dynamic three-point flexural loading. The onset of cracking close to the notch tip, crack propagation in 0° or 90° plies and their interface, crack opening, and ultimately failure of the specimen were captured by high-speed synchrotron X-ray PCI. Additional dynamic experiments were performed to determine the average time when the stress wave propagated through the specimen and correlate the X-ray images with the specimen's force-deflection response. Finally, the surface morphology of each specimen after the dynamic loading was imaged by SEM. Comparison between real-time X-ray images and post-fracture SEM images demonstrated the capability of the X-ray method to record damage evolution inside composites. Furthermore, the high spatial and temporal resolutions of the X-ray setup and edge enhancement by PCI enabled the identification of microscale damage features within 1 μs. Two damaging processes were identified, crack growth was quantified, and fracture toughness of the composites was evaluated. The method is deemed useful to reveal microscale damage mechanisms and track cracking behaviors inside cross-ply GFRCs under dynamic loading in real time.

42 ENGINEERING↗
DOE OSTI2022

A machine learning approach to determine the elastic properties of printed fiber-reinforced polymers

This work focuses on the simultaneous determination of the elastic constants and the fiber orientation state for a short fiber-reinforced polymer composite by performing a minimum of experimental tests. Here we introduce a methodology that enables the inverse determination of fiber orientation state and the in-situ polymer properties by performing tensile tests at the composite coupon level. We demonstrate the approach for the extrusion deposition additive manufacturing (EDAM) process to illustrate one application of the methodology, but the development is such that it can be applied to short fiber-reinforced polymer (SFRP) systems processed via other methods. Currently, developing composites additive manufacturing digital twins require extensive material characterization. In particular, the mechanical characterization of the orthotropic elastic properties of a composite involves extensive sample preparation and testing, therefore the elasticity tensor is generally populated using a micromechanics model. This, however, requires measuring the fiber orientation state in addition to knowing the constituent material properties. Experimentally measuring the fiber orientation state can be tedious and time consuming. Further, optical methods are limited to resolving the orientation of cylindrical fibers or cluster of non-cylindrical fibers, and computed tomography (CT) methods scan regions of volume that are much smaller than a full printed bead. Therefore, we propose a methodology, accelerated by machine learning, to identify the anisotropic mechanical properties and fiber orientation state at the same time. Early results show that inference of the fiber orientation and composite properties is possible with as few as three tensile tests. Our results show that a combination of the choice of the micromechanics model and reliable set of experiments can yield the nine elastic constants, as well as, the fiber orientation state.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of paste microstructure for durability properties of concrete

In this study, paste samples from different cementitious systems were characterized by using X-Ray Micro Computed Tomography (µ-CT) and Fluorescence Microscopy techniques. Quantitative and qualitative aspects of defects from paste samples were investigated to develop indicators of durability related properties of corresponding concrete samples. In the first phase of this study, hour glass shaped 3D printed molds were used to investigate five cementitious combinations consisting of three cement types (Coarse Ground portland cement, Type IL Portland Limestone Cement and Type I/II ordinary portland cement) and fly ash as a supplementary cementitious material. In the second phase, metal molds were used to compare the results of Coarse Ground portland cement with Type I ordinary portland cement, 5% of which was replaced with colloidal nanosilica. Potential correlations between paste and concrete have been presented. This work was supported by US Department of Energy and North Dakota Department of Commerce.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A mesoscale 3D model of irradiated concrete informed via a 2.5 U-Net semantic segmentation

The concrete biological shield in light-water reactors is exposed to neutron and gamma irradiation, which deteriorates the concrete’s mechanical properties in the long term. To assess the irradiation-induced damage, predictive mechanical models are developed and used in parallel with the characterization of irradiated concrete samples. Realistic 3D simulation domains can drastically improve a model’s prediction. In this work, we utilized x-ray computed tomography (XCT) data of a concrete specimen to reconstruct its 3D microstructure. The XCT data shows low contrast between the concrete’s aggregates and cement paste, resulting in poor image segmentation when using traditional unsupervised techniques. To address this issue, we developed and trained a 2.5D U-Net model on only 24 pre-labeled XCT layers to segment 651 layers of the XCT data. The overall F1-score of the model is approximately 96%. Then, we created a 3D finite element (FE) mesh based on the stack of segmented images. The FE model contains radiation-induced expansion, damage, and creep. The constitutive equations are adapted to each phase (aggregates and cement paste). Here, we simulated the effects of neutron irradiation in the concrete specimen as well as the specimen’s mechanical response to uniaxial compression. Finally, model validation was performed using experimental data on similar concrete specimens in the literature.

2.5D U-Net↗
DOE OSTI2022

Half-cell electrode assessments of a crossover-tolerant direct methanol fuel cell with a platinum group metal-free cathode

In this work, a platinum group metal- free (PGM-free) Fe-N-C oxygen reduction reaction (ORR) catalyst derived from metal organic framework precursors (Fe-MOF) is evaluated at the cathode side of a direct methanol fuel cell (DMFC). A wide range of methanol concentrations were used, and the performance of the DMFC using air was evaluated and compared to a commercial Pt/C cathode. We conducted our tests with a custom, integrated H 2 reference electrode that separately provided the anode and cathode overpotentials. This allowed us to perform a Tafel analysis on both electrodes and understand the dominant polarizations involved at the PGM-free cathode and the PtRu/C anode. Overall, we achieved a high cell performance using a Fe-N-C based catalyst under liquid methanol and air operation with a peak power density of 111 mW/cm 2 , where the cathode presented a markedly larger contribution to the voltage loss versus the anode. Additionally, we used nanoscale X-ray computed tomography (nano-CT) to image the Fe-N-C cathode and investigate the ionomer and pore size distributions allowing us to identify areas of improvement for catalyst layer fabrication.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Stochastic generation of electrolyzer anode catalyst layers

Here, we introduce a stochastic methodology to reproduce the complex pore structure observed in commercial iridium catalyst layers. This method preserves the α pore (pores smaller than 250 nm) and β pore (pores greater than or equal to 250 nm) regions of the catalyst layer. The morphology of the generated materials was validated by comparing the pore size distributions of generated materials against those obtained from commercial materials imaged using x-ray nano computed tomography. We further demonstrate that the pore size distributions of the generated materials are statistically indistinguishable from the imaged catalyst layers, indicating that the stochastic methodology is capable of accurately reproducing catalyst layer morphology. Pore network modelling was conducted on the generated catalyst materials to simulate single-phase permeability, electrical conductivity, and ionic conductivity, and these properties were found to be within experimentally measured ranges for electrolyzer catalyst layers. Additionally, simulations were performed on the generated materials with varying ionomer and iridium catalyst loadings. As the ionomer loading is added, proton conductivity increases exponentially, which demonstrates the importance of optimizing ionomer loading, considering that these effects will be exacerbated in the hydration and temperature conditions of operating electrolyzers. The stochastic material generation method presented in this work is a powerful tool for the development of novel low loading catalyst layers, where the effect of various structural parameters on electrolyzer performance characteristics can be explored.

36 MATERIALS SCIENCE↗