Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compressing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Power calculations for isentropic compressions of cryogenic nitrogen

A theoretical analysis was made of the power required for isentropic compressions of cryogenic nitrogen in order to determine the extent to which the drive power for cryogenic tunnels might be affected by real-gas effects. The analysis covers temperatures from 80 to 310 K, pressures from 1.0 to 8.8 atm, and fan pressure ratios from 1.025 to 1.200. The power required to compress cryogenic nitrogen was found to be as much as 9.5 percent lower than that required to compress an ideal diatomic gas. Simple corrections to the ideal-gas values were found to give accurate estimates of the real-gas power values.

Real gas↗
NASA NTRS1992

A compressible Navier-Stokes solver with two-equation and Reynolds stress turbulence closure models

This report outlines the development of a general purpose aerodynamic solver for compressible turbulent flows. Turbulent closure is achieved using either two equation or Reynolds stress transportation equations. The applicable equation set consists of Favre-averaged conservation equations for the mass, momentum and total energy, and transport equations for the turbulent stresses and turbulent dissipation rate. In order to develop a scheme with good shock capturing capabilities, good accuracy and general geometric capabilities, a multi-block cell centered finite volume approach is used. Viscous fluxes are discretized using a finite volume representation of a central difference operator and the source terms are treated as an integral over the control volume. The methodology is validated by testing the algorithm on both two and three dimensional flows. Both the two equation and Reynolds stress models are used on a two dimensional 10 degree compression ramp at Mach 3, and the two equation model is used on the three dimensional flow over a cone at angle of attack at Mach 3.5. With the development of this algorithm, it is now possible to compute complex, compressible high speed flow fields using both two equation and Reynolds stress turbulent closure models, with the capability of eventually evaluating their predictive performance.

Navier-Stoke solver↗
NASA NTRS1945

The Effect of Compression Ratio on Knock Limits of High-Performance Fuels in a CFR Engine II : Blends of 2,2,3-Trimethylpentane with 28-R

The knock-limited performance of blends of 0,50; and 100 percent by volume of 2,2,3-trimethylpentane in 28-R fuel determined with a modified F-4 engine at three sets of conditions varying from severe to mild at each of three compression ratios (6.0, 8.0, and 10.0). A comparison of the knock-limited performance of 2,2,3-trimethylpentane with that of triptane (2,2,3-trimethylbutane) is included. The knock-Limited performance of 2,2,3-trimethylpontane was usually more sensitive to either compression ratio or inlet-air temperature than 28-R fuel, but the ratio of the knock-limited indicated mean effective pressure of a given blend containing 2,2,3-trimethypentane and 28-R to the indicated mean effective pressure of 28-R alone was not greatly affected by compression ratio if the engine operating conditions were mild. Although 2,2,3-trimethylpentane in general had a lower knock-limited performance than triptane, the characteristics of the two fuels were somewhat similar.

FUELS, ANTIKNOCK↗
NASA NTRS2014

Airborne Demonstration of FPGA Implementation of Fast Lossless Hyperspectral Data Compression System

Efficient on-board lossless hyperspectral data compression reduces data volume in order to meet NASA and DoD limited downlink capabilities. The technique also improves signature extraction, object recognition and feature classification capabilities by providing exact reconstructed data on constrained downlink resources. At JPL a novel, adaptive and predictive technique for lossless compression of hyperspectral data was recently developed. This technique uses an adaptive filtering method and achieves a combination of low complexity and compression effectiveness that far exceeds state-of-the-art techniques currently in use. The JPL-developed 'Fast Lossless' algorithm requires no training data or other specific information about the nature of the spectral bands for a fixed instrument dynamic range. It is of low computational complexity and thus well-suited for implementation in hardware.

data compression↗
NASA NTRS2016

Application of Compressive Sensing to Gravitational Microlensing Experiments

Compressive Sensing is an emerging technology for data compression and simultaneous data acquisition. This is an enabling technique for significant reduction in data bandwidth, and transmission power and hence, can greatly benefit spaceflight instruments. We apply this process to detect exoplanets via gravitational microlensing. We experiment with various impact parameters that describe microlensing curves to determine the effectiveness and uncertainty caused by Compressive Sensing. Finally, we describe implications for spaceflight missions.

Compressive Sensing↗
NASA NTRS2020

1- by 1-Foot Supersonic Wind Tunnel Sidewall Flowfield Compression Plate Study

A method for locally increasing the dynamic pressure in the test section of a supersonic wind tunnel is investigated from a theoretical, computational and experimental perspective, culminating in a reduced-scale, proof-of-concept test at Mach 3.44. Symmetric, variable-angle compression plates along the test section sidewalls generate oblique shockwaves to elevate the test section dynamic pressure (q). The experimental effort utilizes boundary-layer pitot rakes to sample the incoming flow near the floor, pitot and static rakes to measure the high-q core flow and numerous surface taps to map out the static pressure distribution along the floor, ceiling and sidewalls. A reliable and robust starting procedure is developed to establish supersonic flow in the test section and behind the compression plates. A characterization of the incoming floor boundary layer reveals previously documented features (such as a bulge toward the centerline) and an unexpected (and as-yet-unexplained) thickening of the boundary layer with increasing Reynolds number around total pressures of 40–60 psia. The high-q core flow is characterized for eight compression plate angles (4.0–8.0°), eight tunnel total pressures (20–139 psia) and three axial stations (24.95–27.35 inches). The peak dynamic pressure rise exceeds expectations. At conditions relevant to full-scale testing (6.0° and 139 psia), the dynamic pressure increases by a factor of 1.73, the Mach number becomes 2.85 and the total pressure drops imperceptibly. Basic distortion metrics show transverse non-uniformity of less than 5 %. Limited spatial resolution in the static rake measurements warrants additional, higher fidelity testing or computational analysis. Surface-mounted, fast-response instrumentation suggests minimal unsteadiness in the flow, less than a few percent of the mean (comparable to the sensor accuracy).

Wind tunnel testing, test techniques/methods, dyna↗
NASA NTRSDate not supplied

Thermal Effects of Pressure Surge and Adiabatic Compression in the Priming of Propulsion and Propellant Transfer Systems

Surge pressures and adiabatic compression during priming of evacuated lines in propulsion and propellant transfer systems has been considered. Test data were obtained for desaturated and saturated water for surge pressures and adiabatic compression for various supply pressures and temperatures. Scaling of surge pressures a t different temperatures has been carried out with the aid of Joukowsky model. The thermal effects associated with surge pressure and the attendant adiabatic compression have been investigated with the a id of a simplified analytical model, which represents an extension of the model developed by Lecourt and Steelant. It has been shown that the predictions from the model compare satisfactorily with test data for a water/helium system, and existing test data for different liquid/gas combinations.

Pressure Surge↗
NASA NTRS2022

Compressive Sensing Based Space Flight Instrument Constellation for Measuring Gravitational Microlensing Parallax

In this work, we provide a compressive sensing architecture for implementing on a space based observatory for detecting transient photometric parallax caused by gravitational microlensing events. Compressive sensing (CS) is a simultaneous data acquisition and compression technique, which can greatly reduce on-board resources required for space flight data storage and ground transmission. We simulate microlensing parallax observations using a space observatory constellation, based on CS detectors. Our results show that average CS error is less than 0.5% using 25% Nyquist rate samples. The error at peak magnification time is significantly lower than the error for distinguishing any two microlensing parallax curves at their peak magnification. Thus, CS is an enabling technology for detecting microlensing parallax, without causing any loss in detection accuracy.

compressive sensing↗
NASA NTRSDate not supplied

Sensitivity Analysis of Geometric Imperfection Sources in Honeycomb Cores on Flatwise Compression Behavior

Manufacturing aluminum honeycomb core material using the expansion process can lead to geometric imperfections in the cellular core structures. These imperfections arise due to irregularities introduced in the initial foil bonding, variations in foil thickness, and residual stresses from manufacturing processes. Such geometric imperfections include cell shape distortions, cell wall waviness, non-uniform cell wall thickness, and variability in the shape and height of the adhesive fillet. Imperfections in the cell walls negatively affect the transverse compression and shear strength, while also reducing the resistance to damage under impact loads. Previous work presented the identification and quantification of these manufactured imperfections using high resolution X-ray computed tomography (CT) scans of honeycomb cores in co-cured composite sandwich panels. The present paper presents a sensitivity analysis of individual components of the sources of geometric imperfections on the flatwise compression of aluminum honeycomb cores. The initial geometric imperfections in honeycomb cells are decomposed into three components, namely cell shape (cell edge length and cell internal angles) in-plane cell wall waviness, and out-of-plane waviness along the core thickness. A sensitivity analysis is conducted using finite element (FE) models of the decomposed imperfections to understand how each component affects compression failure.

aluminum honycomb↗
DOE OSTI2021

Compressed Expanded Natural Graphite (CENG) Processing for PCM Composites

The use of phase change materials (PCMs) in thermal energy storage applications has received considerable attention in recent decades. Organic PCMs are popular due to their high latent heat of fusion, noncorrosive properties, and relative stability over many charge and discharge cycles. A primary limitation of these materials is their low thermal conductivity. This has led researchers to develop various methods to increase thermal conductivity by seeding PCM with or impregnating them into more conductive materials. One method is to impregnate PCMs into compressed expanded natural graphite (CENG) matrices, which can improve thermal conductivity by a factor of 100. CENG matrices have received particular interest due to their low cost, high porosity, small (nano/micro) pore size, high pore density, high thermal conductivity, and ability to be compressed into many geometries. PCM/CENG matrix composites have been extensively studied; however, the effect that CENG processing has on PCM saturation and the overall matrix thermal conductivity has not been well investigated. This processing includes four major steps including graphite intercalation, thermal shock, compression, and PCM saturation. Intercalation involves soaking graphite flakes in sulfuric and/or nitric acid to intercalate the acids between the graphene layers. The graphite flakes are then subjected to a high-temperature thermal shock, during which the intercalated acid is gasified rapidly, pushing the graphene layers apart, resulting in accordion-shaped graphite "worms". The "worms" are then compacted to a desired bulk density and then soaked with molten PCM until fully saturated. The properties of the produced CENG matrix, and its ability to allow PCM permeation, are sensitive to the processing parameters, namely, the thermal shock temperature and exposure time, as well as the matrix apparent density or porosity. Here, we study the effect of the thermal shock conditions necessary to expand intercalated graphite flakes on PCM saturation and the expanded graphite's thermal conductivity and morphology. We found that the thermal shock temperature exhibits the greatest influence. At greater shock temperatures, SEM images showed that expanded graphite worms exhibited greater density of pores, thus increasing total surface area within the matrices. Increasing thermal shock temperature yielded greater overall PCM saturation, as well as an increased rate of saturation. Improvements in PCM saturation rate and overall saturation are obtained as the shock temperature is increased. Longer exposure to thermal shock also improves initial saturation rates and is beneficial if a shortened impregnation time is needed. Thermal shock conditions did not impact thermal conductivity; however, conductivity was largely affected by matrix porosity. A local maximum in axial thermal conductivity was observed at around 83% porosity, which is similar to that observed in previous studies.

compressed expanded natural graphite↗
NASA NTRS1993

Image and Video Compression with VLSI Neural Networks

An advanced motion-compensated predictive video compression system based on artificial neural networks has been developed to effectively eliminate the temporal and spatial redundancy of video image sequences and thus reduce the bandwidth and storage required for the transmission and recording of the video signal. The VLSI neuroprocessor for high-speed high-ratio image compression based upon a self-organization network and the conventional algorithm for vector quantization are compared. The proposed method is quite efficient and can achieve near-optimal results.

compression artificial neural networks VLSI↗
DOE OSTI2024

Intermediate Principal Stress Effects on the 3D Cracking Behavior of Flawed Rocks Under True Triaxial Compression

Crack initiation, growth, and coalescence in flawed rocks have been extensively studied for 2D (planar, penetrating) flaws under uniaxial/biaxial compression. However, little is known as to the mechanisms and processes of cracking from 3D flaws under true triaxial compression, where the intermediate principal stress (σ 2 ) is distinguished from the major and minor principal stresses. In this work, we systematically investigate the effects of σ 2 on the 3D cracking behavior of rock specimens with preexisting flaws, through the use of mechanistic simulations of mixed-mode fracture in rocks. We explore how two characteristics of σ 2 , namely, (i) its orientation with respect to the flaw and (ii) its magnitude, affect two aspects of the cracking behavior, namely, (i) the cracking pattern and (ii) the peak stress. Results show that the orientation of σ 2 exerts more control over the cracking pattern than the flaw inclination angle. The peak stress becomes highest when σ 1 is parallel to the flaw, whereas it becomes lowest when σ 2 is parallel to the flaw. Also, the effects of σ 2 magnitude are more significant when σ 2 becomes more oblique to the flaw plane. On the basis of our observations, we propose mechanisms underlying the cracking behavior of 3D flawed rocks under true triaxial compression.

58 GEOSCIENCES↗
DOE OSTI2024

Compressing branch-and-bound trees

A branch-and-bound (BB) tree certifies a dual bound on the value of an integer program. In this work, we introduce the tree compression problem (TCP): Given a BB tree T that certifies a dual bound, can we obtain a smaller tree with the same (or stronger) bound by either (1) applying a different disjunction at some node in T or (2) removing leaves from T? Here we believe such post-hoc analysis of BB trees may assist in identifying helpful general disjunctions in BB algorithms. We initiate our study by considering computational complexity and limitations of TCP. We then conduct experiments to evaluate the compressibility of realistic branch-and-bound trees generated by commonly-used branching strategies, using both an exact and a heuristic compression algorithm.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

In-Situ X-Ray Imaging High Strain Rate Compression of Laminate Al-Graphene Composite and Mechanical Property Characterization

Owing to the opaque nature of the laminated structures, traditional high-speed optical camera cannot be used to detect the dynamic process of sub-surface deformation. In this article, we report a study of using high speed X-ray imaging to study the high strain rate deformation in laminated Al structures. We used a Kolsky bar apparatus to apply dynamic compression and a high-speed synchrotron X-ray phase contrast imaging (PCI) setup to conduct the in situ X-ray imaging study. The in situ X-ray imaging captures the shock wave propagation in the laminated structures. After shock compression, we characterized the microstructures by using transmission electron microscopy (TEM), which demonstrates an increase of dislocation density. In conclusion, the micro-pillar compression tests show that the yield strength at 0.2% offset of laminated Al-graphene composite has a significant increase of 67%, from 30 to 50 MPa, compared to laminate Al after shock loading.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigating the compressive strength and strain localization of nanotwinned nickel alloys

Sputter deposited nickel-molybdenum-tungsten (Ni-Mo-W) thin films possess a beneficial suite of properties that stem from the extremely fine growth twins that form during the deposition process. Previously these materi- als were only characterized in tension, however, in this study in situ micropillar compression and post-mortem microstructural analysis of nanotwinned Ni 84 Mo 11 W 5 micropillars were employed to measure the compressive response and elucidate the attendant deformation mechanisms. The pillars exhibit Hookean behavior to com- pressive strengths of 3-3.5 GPa and the onset of non-linear plastic flow was manifest by discrete strain bursts and highly localized shear bands. Plastic deformation was concentrated at the top of the pillar, while the bulk of the micropillar was nominally unaffected. Post-mortem investigations indicate that at sufficiently high stresses shear banding is triggered, resulting in intense and highly localized plastic deformation that led to the formation of twin-free nanocrystalline grains within highly deformed shear bands. By contrast, the regions adjacent to the shear bands were unaffected. The absence of detwinning and dislocation glide mechanisms was unexpected and in direct contrast to what has been observed in nanotwinned Cu-Al. Post-mortem observations of the Ni-Mo-W micropillars suggest that the ultrafine twins create a unique form of dislocation starvation and source-limited plasticity. The ultrahigh compressive strength is governed by the triggering of shear bands rather than the activa- tion of dislocation glide. Finally, the specialized nature of plasticity in nanotwinned Ni-Mo-W is clear, even though the precise trigger for shear band formation in nanotwinned Ni-Mo-W remains to be identified.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Utilizing computer vision and artificial intelligence algorithms to predict and design the mechanical compression response of direct ink write 3D printed foam replacement structures

Additive Manufacturing (AM) of porous polymeric materials, such as foams, recently became a topic of intensive research due their unique combination of low density, impressive mechanical properties, and stress dissipation capabilities. Conventional methods for fabricating foams rely on complex and stochastic processes, making it challenging to achieve precise architectural control of structured porosity. In contrast, AM provides access to a wide range of printable materials, where precise spatial control over structured porosity can be modulated during the fabrication process enabling the production of foam replacement structures (FRS). Current approaches for designing FRS are based on intuitive understanding of their properties or an extensive number of finite element method (FEM) simulations. These approaches, however, are computationally expensive and time consuming. As such, in this work, we present a novel methodology for determining the mechanical compression response of direct ink write (DIW) 3D printed FRS using a simple cross-sectional image. By obtaining measurement data for a relatively small number of samples, an artificial neural network (ANN) was trained, and a computer vision algorithm was used to make inferences about foam compression characteristics from a single cross-sectional image. Finally, a genetic algorithm (GA) was used to solve the inverse design problem, generating the AM printing parameters that an engineer should use to achieve a desired compression response from a DIW printed FRS. The methods developed herein present an avenue for entirely autonomous design and analysis of additively manufactured structures using artificial intelligence.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Capture of novel sp 3 hybridized Z-BN by compressing boron nitride nanotubes with small diameter

Experimental synthesis of new sp 3 hybridized carbon/boron nitride structures remains challenging despite that numerous sp 3 structures have been proposed in theory. Here, we showed that compressed multi-walled boron nitride nanotubes (MWBNNTs) and boron nitride peapods (C 60 @BNNTs) with small diameters could transform into a new sp 3 hybridized boron nitride allotrope (Z-BN). This strategy is considered from the topological transition point of view in boron nitride nanotubes upon compression. Due to the increased curvature in compressed small-diameter MWBNNTs, the uncommon 4- and 8-membered rings in Z-BN could be more favorably formed. And the irreversible tube collapse is proved to be a critical factor for the capture of the formed Z-BN, because of the competition between the resilience of tube before collapse and the stress limitation for the lattice stabilization of Z-BN upon decompression. In this case, Z-BN starts to form above 19.0 GPa, which is fully reversible below 45 GPa and finally becomes quenchable at 93.5 GPa. Consequently, this collapse-induced capture of the high-pressure phase could also be extended to other tubular materials for quenching novel sp 3 structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Combustion dynamics of crude and upgraded Thermal DeOxygenation oils in a compression ignition engine

Thermal DeOxygenation (TDO) is a robust thermochemical conversion scheme to produce hydrocarbons from biomass feedstock. The process targets the carbohydrate fraction of biomass to yield a broad mixture of primarily aromatic hydrocarbons within a boiling point range of 348–798 K with low oxygen content (<4 wt%). The resulting materials are amenable to traditional hydrotreating and distillation processes with approximately 70% by mass in the distillate fuel range. The simple conversion scheme combined with commercially viable upgrading routes makes TDO oils a feasible alternative fuel for transportation applications. Here this paper is the first systematic treatment of fit-for-purpose testing of TDO oils in a compression ignition engine. Blends of partially upgraded TDO oils (e.g. whole oil, distilled oil, hydrotreated oil and hydrotreated-distilled oil) are prepared with certified ultra-low sulfur diesel at 5%, 10%, 15% and 20% by volume. The resulting fuels are analyzed for fuel characteristics and combustion dynamics in an instrumented single-cylinder compression ignition engine. All fuel blends at 10% blend level by volume exhibited adequate engine performance. Hydrotreating of the oils is a necessary step to meet cetane number and EPA soot emissions requirements at 20% blend volume. Combined distillation and hydrotreatment meet or exceed all fuel specification and engine performance benchmarks. Partially upgraded TDO oils are suitable fuel options for compression ignition applications.

42 ENGINEERING↗