Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Aeroelastic Stability for Straight and Swept-Tip Rotor Blades in Hover and Forward Flight

Two isolated, hingeless rotors with identical fiber-reinforced composite root flexures were tested in hover and forward flight at realistic tip speeds. The rotors differed in blade planform and structure. The first blade set was of rectangular planform. The second set had blades of stiffer construction with swept-tips. The purpose of these tests was to measure the isolated rotor aeroelastic stability of bending/torsion coupled rotor blades over a range of flight conditions. The two soft inplane rotor systems were designed with low first torsion frequency to emphasize the effects of torsion. Regressing lag mode damping is shown in hover with precone and collective pitch variations and in forward flight with airspeed, shaft angle, precone and collective pitch variations. Correlation with comprehensive analysis for a number of test conditions is shown. Agreement in hover is excellent and forward flight correlation is reasonably good.

REGRESSING LAG MODE DAMPING↗
NASA NTRS2014

Blade Motion Correlation for the Full-Scale UH-60A Airloads Rotor

Testing was successfully completed in May 2010 on a full-scale UH-60A rotor system in the USAF's National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel.[1] The primary objective of this NASA Army sponsored test program was to acquire a comprehensive set of validation-quality measurements ona full-scale pressure-instrumented rotor system at conditions that challenge the most sophisticated modeling andsimulation tools. The test hardware included the same rotor blades used during the UH-60A Airloads flight test.[2] Key measurements included rotor performance, blade loads, blade pressures, blade displacements, and rotorwake measurements using large-field Particle Image Velocimetry (PIV) and Retro-reflective Background Oriented Schlieren (RBOS).

Airloads Rotor↗
NASA NTRS2016

An Assessment of the Icing Blade and the SEA Multi-Element Sensor for Liquid Water Content Calibration of the NASA GRC Icing Research Tunnel

The Icing Research Tunnel at NASA Glenn has recently switched from using the Icing Blade to using the SEA Multi-Element Sensor (also known as the multi-wire) for its calibration of cloud liquid water content. In order to peform this transition, tests were completed to compare the Multi-Element Sensor to the Icing Blade, particularly with respect to liquid water content, airspeed, and drop size. The two instruments were found to compare well for the majority of Appendix C conditions. However, it was discovered that the Icing Blade under-measures when the conditions approach the Ludlam Limit. This paper also describes data processing procedures for the Multi-Element Sensor in the IRT, including collision efficiency corrections, mounting underneath a splitter plate, and correcting for a jump in the compensation wire power. Further data is presented to describe the repeatability of the IRT with the Multi-Element Sensor, health-monitoring checks for the instrument, and a sensing-element configuration comparison. Ultimately these tests showed that in the IRT, the multi-wire is a better instrument for measuring cloud liquid water content than the blade.

aircraft icing↗
NASA NTRS2021

Evaluations of Damaged High-Pressure Compressor Blades in Two Turbine Engines of NASA DC–8

A series of flights were performed by the NASA DC-8 for the FIREX-AQ missions to observe the effects of wildfires and agricultural fires on air quality and climate in selected locations of the United States. Borescope evaluations after these flights indicated accelerated damage had occurred over this flight series to the blades in the high pressure compressor section of all four CFM56-2C1 turbine engines. This erosion and impact damage appeared to vary in severity, and appeared most severe for engines 3 and 4 located on the right wing of the DC-8.Engine 3 had the most flight hours and cycles since last overhaul of 7,152 h and 2,502 cycles. Engine 4 had the lowest flight hours and cycles since last overhaul of 1,354 h and 369 cycles. For these reasons, three noticeably damaged blades were selected from the high pressure compressor for each of these two engines, and then evaluated at NASA GRC using optical and scanning electron microscopy. Engine 3 compressor blades had both erosion and impact damage that were observed and characterized. The erosion damage was associated with embedded particles 13 μm to 42 μm in sectioned width, composed of varied compositions ranging from SiO2 to SiO2 also containing Ca, Mg, and Al (CMAS). The impact damage was associated with the impacts of larger objects at least 650 μm to 850 μm in width, but only small fragments 5 μm to 15 μm in sectioned width were embedded in the impact surface, also composed of SiO2 to SiO2 containing Ca, Mg, and Al (CMAS). On the other hand, engine 4 blades had only impact damage that was observed and characterized. This impact damage was associated with impacts of objects at least 1,480 μm to 2,080μm in width. Small fragments 5 μm to 15 μm in sectioned width were embedded in the impact surface. For one impact, the fragments were again composed of SiO2 to SiO2 containing Ca, Mg, and Al (CMAS). For two other impacts, the fragments were often composed of Fe, and less frequently Cu.

turbine↗
NASA NTRS1941

Wind-tunnel Tests of Eight-blade Single and Dual-rotating Propellers in the Tractor Position

Tests of 10-ft. diameter, eight-blade, single - and dual - rotating propellers were conducted in 20-ft propeller research tunnel. Propellers were mounted at front end of a streamline body in spinners that covered hubs and parts of shanks. Effect of a symmetrical wing mounted in slipstream was investigated. Blade-angle settings ranged from 20 Degrees to 65 Degrees. Results indicated that dual rotation resulted in gains of from 1 to 8 percent in efficiency over single rotation for eight-blade propellers, but presence of a wing reduced gain about one-half. Greater power absorption caused by dual rotation over flight range and higher efficiency or thrust for range of take-off and climb was indicated

PROPELLER-WING COMBINATIONS↗
NASA NTRS2012

Initial Investigation of the Acoustics of a Counter-Rotating Open Rotor Model with Historical Baseline Blades in a Low-Speed Wind Tunnel

A counter-rotating open rotor scale model was tested in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel (LSWT). This model used a historical baseline blade set with which modern blade designs will be compared against on an acoustic and aerodynamic performance basis. Different blade pitch angles simulating approach and takeoff conditions were tested, along with angle-of-attack configurations. A configuration was also tested in order to determine the acoustic effects of a pylon. The shaft speed was varied for each configuration in order to get data over a range of operability. The freestream Mach number was also varied for some configurations. Sideline acoustic data were taken for each of these test configurations.

Acoustics↗
NASA NTRS1971

Design and two dimensional cascade test of a jet-flap turbine stator blade with ratio of axial chord to spacing of 0.5

A jet-flap blade was designed for a velocity diagram typical of the first-stage stator of a jet engine turbine and was tested in a simple two-dimensional cascade of six blades. The principal measurements were blade surface static pressure and cross-channel surveys of exit total pressure, static pressure, and flow angle. The results of the experimental investigation include blade loading, exit angle, flow, and loss data for a range of exit critical velocity ratios and three jet flow conditions.

Stabe, R. G.↗
NASA NTRS1971

Computer program for design of two-dimensional supersonic turbine rotor blades with boundary-layer correction

A FORTRAN 4 computer program for the design of two-dimensional supersonic rotor blade sections corrected for boundary-layer displacement thickness is presented. The ideal rotor is designed by the method of characteristics to produce vortex flow within the blade passage. The boundary-layer parameters are calculated by Cohen and Reshotoko's method for laminar flow and Sasman and Cresci's method for turbulent flow. The program input consists essentially of the blade surface Mach number distribution and total flow conditions. The primary output is the corrected blade profile and the boundary-layer parameters.

Goldman, L. J.↗
NASA NTRS1972

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 3: Data and performance for stage C

Stage C, comprised of tandem-airfoil rotor C and tandem-airfoil stator B, was designed and tested to establish performance data for comparison with the performance of conventional single-airfoil blading. Velocity diagrams and blade leading and trailing edge metal angles selected for the conventional rotor and stator blading were used in the design of the tandem blading. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. At design equivalent rotor speed, rotor C achieved a maximum adiabatic efficiency of 91.8% at a pressure ratio of 1.31. The stage maximum adiabatic efficiency was 86.5% at a pressure ratio of 1.31.

Brent, J. A.↗
NASA NTRS1972

Study of blade clearance effects on centrifugal pumps

A program of analysis, design, fabrication, and testing has been conducted to develop and experimentally verify analytical models to predict the effects of impeller blade clearance on centrifugal pumps. The effect of tip clearance on pump efficiency, and the relationship between the head coefficient and torque loss with tip clearance was established. Analysis were performed to determine the cost variation in design, manufacture, and test that would occur between unshrouded and shrouded impellers. An impeller, representative of typical rocket engine impellers, was modified by removing its front shroud to permit variation of its blade clearances. It was tested in water with special instrumentation to provide measurements of blade surface pressures during operation. Pump performance data were obtained from tests at various impeller tip clearances. Blade pressure data were obtained at the nominal tip clearance. Comparisons of predicted and measured data are given.

Hoshide, R. K.↗
NASA NTRS1972

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 5: Analysis and design of stages D and E

A conventional and a tandem bladed stage were designed for a comparative experimental evaluation in a 0.8 hub/tip ratio single-stage compressor. Based on a preliminary design study, a radially constant work input distribution was selected for the rotor designs. Velocity diagrams and blade leading and trailing edge angles selected for the conventional rotor and stator were used in the design of the tandem blading. The effects of axial velocity ratio and secondary flow on turning were included in the selection of blade leading and trailing edge angles. Design values of rotor tip velocity and stage pressure ratio were 757 ft/sec and 1.26, respectively.

Brent, J. A.↗
NASA NTRS1973

Single stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 4: Data and performance for stage B

Stage B, composed of tandem-airfoil rotor B and stator B, was tested with uniform inlet flow and with hub radial, tip radial and 90 degree one-per-revolution circumferential distortion of the inlet flow as part of an overall program to evaluate the effectiveness of tandem airfoils for increasing the design point loading capability and stable operating range of rotor and stator blading. The results of this series of tests provide overall performance and blade element data for evaluating: (1) the potential of tandem blading for extending the loading limit and stable operating range of a stage representative of a middle stage of an advanced high pressure compressor, (2) the effect of loading split between the two airfoils in tandem on the performance of tandem blading, and (3) the effects of inlet flow distortion on the stage performance. The rotor had an inlet hub/tip ratio of 0.8 and a design tip velocity of 757 ft/sec. With uniform inlet flow, rotor B achieved a maximum adiabatic efficiency of 88.4% at design equivalent rotor speed and a pressure ratio of 1.31. The stage maximum adiabatic efficiency at design equivalent rotor speed with uniform inlet flow was 82.5% at a pressure ratio of 1.28. Tip radial and circumferential distortion of the inlet flow caused substantial reductions in surge margin.

Brent, J. A.↗
NASA NTRS1973

Sensitivity of rotor blade vibration characteristics to torsional oscillations.

A theoretical investigation of dynamic response characteristics of helicopter rotor blades in forward flight was carried out with special emphasis on the torsional degrees-of-freedom. The finite element method was applied in the formulation of the coupled equations of motion for flapwise bending and torsion for blades with non-collinear elastic, mass and aerodynamic axes. The sensitivity of blade vibration characteristics with respect to structural, geometric and aerodynamic properties as well as flight conditions was evaluated. Numerical results for sample blades were plotted to show the variation of the coupling between bending and torsional components of the response.

Bratanow, T.↗
NASA NTRS1974

Cold-air study of the effect on turbine stator blade aerodynamic performance of coolant ejection from various trailing-edge slot geometries. 1: Experimental results

Trailing-edge slot configurations were investigated in a two-dimensional cascade of turbine stator blades. The trailing-edge slots were incorporated into blades with round trailing edges. The five blade configurations investigated included blades with two different trailing-edge thicknesses and four different slot widths. The results of the investigation showed that there was, in general, a significant increase in primary-air efficiency due to the coolant flow, the increase varying with slot configuration. For the five configurations tested, the average percent change in primary-air efficiency per percent coolant flow varied almost linearly from zero to about 1.4 percent over a range of coolant- to primary-air exit-velocity ratios between 0 and 1.2. However, for different configurations there was considerable deviation from the average values in the lower range of exit velocity ratios.

Prust, H. W., Jr.↗
NASA NTRS1974

Acoustic results of supersonic tip speed fan blade modification

A supersonic tip speed single stage fan was modified with the intent of reducing multiple pure tone (MPT) or buzz saw noise. There were three modifications to the blades from the original design. The modifications to the blade resulted in an increase in cascade throat area causing the shock to start at a lower corrected fan speed. The acoustic results without acoustically absorbing liners showed substantial reduction in multiple pure tone levels. However, an increase in the blade passing frequency noise at takeoff fan speed accompanied the MPT reduction. The net result however, was a reduction in the maximum 1000-foot (304.8 m) altitude level flyover PNL. For the case with acoustic treatment in the inlet outer wall, the takeoff noise increased relative to an acoustically treated baseline. This was largely due to the increased blade passing frequency noise which was not effectively reduced by the liner.

Jutras, R. R.↗
NASA NTRS1973

Some conclusions regarding the aeroelastic stability of hingeless helicopter blades in hover and in forward flight

In this paper results and conclusions obtained from the study of the aeroelastic instability of hingeless helicopter blades are presented. First, the large amplitude coupled flap-lag equations of motion of a hingeless elastic helicopter blade are solved using an asymptotic expansion procedure in multiple time scales. Both hover and forward flight cases are considered. Stability boundaries and amplitudes of nonlinear response are obtained. From these, the importance of the nonlinear coupling and the effect of the periodic coefficients is determined. Next, using a system of linearized coupled flap-lag-pitch equations in hover, various divergence mechanisms for hingeless blades are shown. Finally, the flutter boundaries for coupled flap-lag-pitch are obtained. The effect of the torsional degree of freedom on the flap-lag type of instability is investigated. Similarly the effect of lag on the flap-pitch type of instability is considered. In addition, the effect of various blade parameters on the stability boundaries is shown.

Friedmann, P.↗
NASA NTRS1974

The prediction of rotor rotational noise using measured fluctuating blade loads

In tests conducted at the NASA Langley Research Center Helicopter Rotor Test Facility, simultaneous measurements of the high-frequency fluctuating aerodynamic blade loads and far-field radiated noise were made on a full-scale, nontranslating rotor system. After their characteristics were determined, the measured blade loads were used in an existing theory to predict the far-field rotational noise. A comparison of the calculated and measured rotational noise is presented with specific attention given to the effect of blade loading coefficients, chordwise loading distributions, blade loading phases, and observer azimuthal position on the predictions.

Hosier, R. N.↗