Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1963

Aeroelastic Tests of an Eight Percent Scale Saturn C-1 Block II

Buffet and flutter characteristics of Saturn Apollo mission were studied using a dynamically scaled model. The model was built around a central aluminum tube for scaled stiffness distribution and strength to resist loads imposed during testing. Styrofoam sections attached to the core provided the correct external contours. Lead weights were added for correct mass distribution. An electromagnetic shaker was used to excite the model in its flexible modes of vibration during portions of the test. The model was supported on a sting, mounted by leaf springs, cables and torsion bars. The support system provided for simulating the full scale rigid body pitch frequency with minimum restraint imposed on elastic deflections. Bending moments recorded by sensors on the aluminum tube. Several modified nose configurations were tested: The basic configuration was tested with and without a flow separator disk on the escape rocket motor, tests also were made with the escape tower and rocket motor removed completely. For the final test, the Apollo capsule was replaced with a Jupiter nose cone. The test program consisted of determining model response throughout the transonic speed range at angles of attack up to 6 degrees and measuring the aerodynamic damping over the same range for the basic model and the modified configurations. Signals from the model pickup were recorded on tape for later analysis. The data obtained were used to estimate bending moments that would be produced on the full-scale vehicle by aerodynamic forces due to buffeting.

EXPERIMENTS↗
NASA NTRS1989

Low speed wind tunnel investigation of the flow about delta wing, oscillating in pitch to very high angle of attack

Six-component airload histories were obtained for models of aspect ratio 1, 1.5, and 2. Examples are given from data obtained over a range of 'reduced frequency' parameters from 0.01 to 0.08. They include the unsteady response of the leading-edge vortices, as evidenced both by the time-dependent airloads and motion pictures of smoke released from the leading edge and illuminated by a thin sheet of laser light.

Jarrah, Mohammad-Ameen M.↗
NASA NTRS2001

Prediction of Unsteady Aerodynamic Coefficients at High Angles of Attack

The nonlinear indicial response method is used to model the unsteady aerodynamic coefficients in the low speed longitudinal oscillatory wind tunnel test data of the 0.1 scale model of the F-16XL aircraft. Exponential functions are used to approximate the deficiency function in the indicial response. Using one set of oscillatory wind tunnel data and parameter identification method, the unknown parameters in the exponential functions are estimated. The genetic algorithm is used as a least square minimizing algorithm. The assumed model structures and parameter estimates are validated by comparing the predictions with other sets of available oscillatory wind tunnel test data.

Pamadi, Bandu N.↗
NASA NTRS1954

Free-Flight Tests of 0.11-Scale North American F-100 Airplane Wings to Investigate the Possibility of Flutter in Transonic Speed Range at Varying Angles of Attack

Free-flight tests in the transonic speed range utilizing rocketpropelled models have been made on three pairs of 0.11-scale North American F-100 airplane wings having an aspect ratio of 3.47, a taper ratio of 0.308, 45 degree sweepback at the quarter-chord line, and thickness ratios of 31 and 5 percent to investigate the possibility of flutte r. Data from tests of two other rocket-propelled models which accidentally fluttered during a drag investigation of the North American F-100 airplane are also presented. The first set of wings (5 percent thick) was tested on a model which was disturbed in pitch by a moving tail and reached a maximum Mach number of 0.85. The wings encountered mild oscillations near the first - bending frequency at high lift coefficients. The second set of wings 9 percent thick was tested up to a maximum Mach number of 0.95 at (2) angles of attack provided by small rocket motors installed in the nose of the model. No oscillations resembling flutter were encountered during the coasting flight between separation from the booster and sustainer firing (Mach numbers from 0.86 to 0.82) or during the sustainer firing at accelerations of about 8g up to the maximum Mach number of the test (0.95). The third set of wings was similar to the first set and was tested up to a maximum Mach number of 1.24. A mild flutter at frequencies near the first-bending frequency of the wings was encountered between a Mach number of 1.15 and a Mach number of 1.06 during both accelerating and coasting flight. The two drag models, which were 0.ll-scale models of the North American F-100 airplane configuration, reached a maximum Mach number of 1.77. The wings of these models had bending and torsional frequencies which were 40 and 89 percent, respectively, of the calculated scaled frequencies of the full-scale 7-percent-thick wing. Both models experienced flutter of the same type as that experienced-by the third set of wings.

O'Kelly, Burke R.↗
NASA NTRS1982

Computations and turbulent flow modeling in support of helicopter rotor technology

Efforts continue to investigate the applicability of the Deiwert's time dependent numerical airfoil calculation code to the simulation of two dimensional airfoil flows with large amounts of separation present. A modified logarithmic region mixing length term produced substantial differences in the calculated flow fields for the large separation of the M=0.4, high angle of attack cases. Reasons are given for interest in applying that model to previously investigated cases of the 64A010 airfoil section at Mach number 0.8 for angles of attack of 4 deg and 6.2 deg. The effects of these turbulence models at alterations and the time dependent behavior from impulsively started conditions are discussed.

Rose, W. C.↗
NASA NTRS1983

Installed nacelle drag-improvement tests of an M = 0.8 turboprop transport configuration

An unpowered semispan model of a representative turboprop configuration was tested to determine the effect of configuration modifications on the the nonmetric body and wing juncture. It is indicated that the jet off nacelle-installation drag can be approximately 25% of the cruise drag. However, the losses can be reduced to 17% by changes to the wing leading edge and nacelle intersection. Comparison of test results from a semispan nonmetric fuselage model with those from a full span metric fuselage show differences in angles of attack produced the same lift. It is found that the constant lift drag rise of the semispan model is higher because of the increased angle of attack to achieve the same lift.

Levin, A. D.↗
NASA NTRS1991

A water tunnel flow visualization study of the vortex flow structures on the F/A-18 aircraft

The vortex flow structures occurring on the F/A-18 aircraft at high angles of attack were studied. A water tunnel was used to gather flow visualization data on the forebody vortex and the wing leading edge extension vortex. The longitudinal location of breakdown of the leading edge vortex was found to be consistently dependent on the angle of attack. Other parameters such as Reynolds number, model scale, and model fidelity had little influence on the overall behavior of the flow structures studied. The lateral location of the forebody vortex system was greatly influenced by changes in the angle of sideslip. Strong interactions can occur between the leading edge extension vortex and the forebody vortex. Close attention was paid to vortex induced flows on various airframe components of the F/A-18. Reynolds number and angle of attack greatly affected the swirling intensity, and therefore the strength of the studied vortices. Water tunnel results on the F/A-18 correlated well with those obtained in similar studies at both full and sub scale levels. The water tunnel can provide, under certain conditions, good simulations of realistic flows in full scale configurations.

Sandlin, Doral R.↗
NASA NTRS1996

Flight test maneuvers for closed loop lateral-directional modeling of the F-18 High Alpha Research Vehicle (HARV) using forebody strakes

Flight test maneuvers are specified for the F-18 High Alpha Research Vehicle (HARV). The maneuvers were designed for closed loop parameter identification purposes, specifically for lateral linear model parameter estimation at 30, 45, and 60 degrees angle of attack, using the Actuated Nose Strakes for Enhanced Rolling (ANSER) control law in Strake (S) model and Strake/Thrust Vectoring (STV) mode. Each maneuver is to be realized by applying square wave inputs to specific pilot station controls using the On-Board Excitation System (OBES). Maneuver descriptions and complete specification of the time/amplitude points defining each input are included, along with plots of the input time histories.

Morelli, E. A.↗
NASA NTRS1998

Accommodating Actuator Failures in Flight Control Systems

A technique for the design of flight control systems that can accommodate a set of actuator failures is presented. As employed herein, an actuator failure is defined as any change in the parametric model of the actuator which can adversely affect actuator performance. The technique is based upon the formulation of a fixed feedback topology which ensures at least stability in the presence of the failures in the set. The fixed compensation is obtained from a loop-shaping design procedure similar to Quantitative Feedback Theory and provides stability robustness in the presence of uncertainty in the vehicle dynamics caused by the failures. System adaptation to improve performance after actuator failure(s) occurs through a static gain adjustment in the compensator followed by modification of the system prefilter. Precise identification of the vehicle dynamics is unnecessary. Application to a single-input, single-output design using a simplified model of the longitudinal dynamics of the NASA High Angle of Attack Research Vehicle is discussed. Non-real time simulations of the system including a model of the pilot demonstrate the effectiveness and limitations of the approach.

Hess, R. A.↗
NASA NTRS1983

Estimation of parameters involved in high angle-of-attack aerodynamic theory using spin flight test data

The difficulty in applying parameter estimation techniques to spinning airplanes is due in part to the unwieldy number of possible combinations of terms in the equations of motion, when the model structure is unknown. The combination of high angle of attack and high rotation rate results in aerodynamic functions which are quite complex. For wing dominated configurations it is advantageous to use aerodynamic theory to generate the model structure. In this way, the number of unknown parameters is reduced and the model accuracy may be increased. Under conditions for which the theory is inadequate, however, model accuracy may be reduced. Strip theory, for example, is incapable of predicting autorotative rolling moments indicated by wind tunnel tests at angles of attack exceeding 40 degrees. An improved aerodynamic theory would be necessary to successfully apply the technique advanced for such regions.

Taylor, L. W., Jr.↗
NASA NTRS1990

Delta wing surface pressures for high angle of attack maneuvers

A wind tunnel experiment was performed on a delta wing with a leading edge sweep of 70 deg. Unsteady pressures were measured on the suction surface of the wing as it was oscillated from 0-30 deg, and 2-60 deg angle-of-attack. Pressure coefficients were measured at different surface locations for two pitch rates. Static pressure measurements were also obtained for comparison with the dynamic results. The Reynolds number was fixed at 420,000, based on the centerline chord length. Pressure measurements were made from 35-90 percent of the chord, along a ray from the apex at 60 percent of the local semispan. Spanwise measurements were also made at a constant chord location, x/c = 75 percent from the apex. The unsteady pressure data over the 0-30 deg angle-of-attack range showed pressures fluctuating in phase with model motion, and little overshoot from the static values. The pressures for the large amplitude motion showed large overshoots from the static values. In addition, during the high angle-of-attack portion of the motion, the upstroke (angle of attack increasing) pressure coefficients were typically much lower than the downstroke values. For the lower pitch rate, there was little difference between upstroke and downstroke pressures at the low angles of attack.

Thompson, S. A.↗
NASA NTRS1959

Static Stability Characteristics of Three Thick Wing Models with Parabolic Plan Forms at a Mach Number of 3.11

An experimental investigation has been made to determine the static stability characteristics of three thick wing models with parabolic plan forms at a Mach number of 3.11 for angles of attack from about -6 to 16 deg. The primary variable was aspect ratio, with the plan-form area and the ratio of base height to span kept the same for all three models. All models had stable, linear pitching-moment curves about the quarter chord of the wing mean aerodynamic chord. The model with the lowest aspect ratio attained a maximum untrimmed lift-drag ratio of about 5.0 at an angle of attack of about 8 deg. Increasing the aspect ratio (which was accompanied by an increase in base area because the ratio of the base height to span was kept constant) caused a decrease in maximum lift-drag ratio. All models were directionally stable for the range of angle of attack of the tests. Addition of a vertical tail to the models caused an increase in the directional stability over the angle-of-attack range. In general, the lateral aerodynamic characteristics of the models were not linear functions of angle of attack over any appreciable angle-of-attack range.

Queijo, M. J.↗
NASA NTRS1992

Low-to-high altitude predictions of three-dimensional ablative reentry flowfields

A new coupled-chemistry PNS scheme has been developed to study 3D hypersonic reentry flows over sphere cones at small angles of attack. A new quasi-steady ablation model for Teflon was used to predict ablative reentry flow fields under laminar, transitional, and turbulent conditions. This solution scheme uses a new two-step solution scheme for solving the species conservation equations under low-altitude conditions. As an example, the scheme is used to study hypersonic flow over a 6-deg sphere-cone configuration at 50 and 125 kft conditions under zero and nonzero angle of attack conditions.

Bhutta, Bilal A.↗
NASA NTRS1987

Investigation of a delta-wing fighter model flow field at transonic speeds

The paper reports a flow-field investigation on a 7.52-percent scale model of an advanced fighter aircraft design conducted in the NASA-Langley 16-ft Transonic Tunnel. The effects of free-stream Mach number, angle-of-attack, angle of sideslip, and various vortex control devices on the local flow values were studied. The model was tested at Mach numbers of 0.6, 0.9, and 1.2 and the angles of sideslip of 0 and +/- 5 deg; the model angle-of-attack was varied from -4 to 30 deg. Results are presented in terms of contour plots of local total pressure recovery. The dominant influence on the over-wing flow field was found to be the wing leading-edge vortex which first appears in the survey region at an angle-of-attack of 8 deg and increases in strength and influence with increasing angle-of-attack, finally dominating the entire survey region at very high angles-of-attack.

Bare, E. Ann↗
NASA NTRS1961

Transonic and Supersonic Flutter Investigation of 1/2-Size Models of All-Movable Canard Surface of an Expendable Powered Target

A transonic and a supersonic flutter investigation of 1/2-size models of the all-movable canard surface of an expendable powered target has been conducted in the Langley transonic blowdown tunnel and in the Langley 9- by 18-inch supersonic aeroelasticity tunnel, respectively. The transonic investigation covered a Mach number range from 0.7 to 1.3, and the supersonic investigation was made at Mach numbers 1.3, 2.O, and 2.55. The effects on the flutter characteristics of the models of different levels of stiffness and of free play in the pitch control linkage were examined. The semispan models, which were tested at an angle of attack of 0 deg, had pitch springs with the scaled design and 1/2 the scaled design pitch stiffness and total free play in pitch ranging from 0 to 1 deg. An additional model configuration which had a pitch spring 1/4 the scaled design pitch stiffness and no free play in pitch was included in the supersonic tests. All model configurations investigated were flutter free up to dynamic pressures 32 percent greater than those required for flight throughout the Mach number range. Several model configurations were tested to considerably higher dynamic pressures without obtaining flutter at both transonic and supersonic speeds.

Ruhlin, Charles L.↗
NASA NTRS1994

Parameters of Nocilla gas/surface interaction model from measured accomodation coefficients

Free-molecule aerodynamic coefficients are computed for a flat plate surface element at various angles of attack using the normal and tangential accomodation coefficients and the Nocilla model of the gas/surface interaction. The Nocilla model assumes that the molecules reflect from a surface in the form of a drifting Maxwellian with a mean velocity at a specific temperature. The computations use curve fits of the angular variation of the existing measurements of the accomodation coefficients and of the parameters in the Nocilla model. The two methods indicate that a surface element has considerably more lift than predicted by an assumption of diffuse scattering. In other respects the predictions by the two methods do not agree.

Collins, Frank G.↗
DOE OSTI2025

Operational resilience of additively manufactured parts to stealthy cyberphysical attacks using geometric and process digital twins

Cyberphysical attacks on the digital backbone of Additive Manufacturing (AM) can compromise the printed part’s functionality. They can alter features in the digital geometry to introduce geometric defects (e.g., missing fillets) or alter process parameters to create local defects (e.g., voids). Addressing the downtime, waste, and quality deterioration associated with existing solutions requires operational resilience, i.e., rapid elimination or disruption of defect formation (to retain part function) without production stoppage or part disposal (to retain yield). This need is unmet due to the inherently unpredictable nature of attack-induced alterations, lack of access to the original geometric model for identification of altered geometric features, and in-process imposition of unknown process dynamics via attack-driven alteration of real-time-uncontrolled (or exogenous) parameters. This work establishes the above-mentioned operational resilience for the first time by creating two Digital Twins (DT). The Geometric DT (Geo-DT) is based on a unique physical-field-driven soft sensor and topology optimization method. The Process Digital Twin (Pro-DT) combines local defect quantification with a novel Reinforcement Learning formulation and training method. The importance of these methodological advances and the scalability of our approach are examined on a real AM testbed. It is shown that Geo-DT can correct geometric defects without access to the original digital geometry or explicit knowledge of attack-altered geometric features. Further, Pro-DT can accelerate real-time disruption of local defects despite attack-driven imposition of unknown process dynamics. We discuss how our framework goes beyond the contemporary focus on pre-attack security and in-attack detection towards resilience for AM and beyond.

Additive Manufacturing↗
NASA NTRS1989

Computing viscous reactive flow over blunt winged vehicles

A hypersonic flow simulation methodology is developed for analyzing thermochemical nonequilibrium and viscous phenomena associated with space-flight vehicles at realistic conditions. The computer code consists of grid generation, Navier-Stokes and species models, and equation solvers for a complete configuration at arbitrary angles of attack. Provisions are implemented in the code to consider chemically frozen or equilibrium chemistry, inviscid model, conic configurations and simplifications of physical parameters for verifying solution consistency and accuracy. Implications of physical modeling and input parameters on a blunt-cone flow are investigated in details. Applications to USA Orbiter-like vehicles have emphasized the leeside canopy flow as well as the bow-wing shock interaction problem at Mach 22 and 40 deg angle of attack. Comparison of windward centerline pressures and heating rates with available wind-tunnel and flight data is in progress.

Li, C. P.↗