SEARCH · Engineering Papers

Results for “application of power electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS2004

COTS MEMS Flow-Measurement Probes

As an alternative to conventional tubing instrumentation for measuring airflow, designers and technicians at Glenn Research Center have been fabricating packaging components and assembling a set of unique probes that contain commercial off-the-shelf (COTS) microelectromechanical systems (MEMS) sensor chips. MEMS sensor chips offer some compelling advantages over standard macroscopic measurement devices. MEMS sensor technology has matured through mass production and use in the automotive and aircraft industries. At present, MEMS are the devices of choice for sensors in such applications as tire-pressure monitors, altimeters, pneumatic controls, cable leak detectors, and consumer appliances. Compactness, minimality of power demand, rugged construction, and moderate cost all contribute to making MEMS sensors attractive for instrumentation for future research. Conventional macroscopic flow-measurement instrumentation includes tubes buried beneath the aerodynamic surfaces of wind-tunnel models or in wind-tunnel walls. Pressure is introduced at the opening of each such tube. The pressure must then travel along the tube before reaching a transducer that generates an electronic signal. The lengths of such tubes typically range from 20 ft (approx.= 6 m) to hundreds of feet (of the order of 100 m). The propagation of pressure signals in the tubes damps the signals considerably and makes it necessary to delay measurements until after test rigs have reached steady-state operation. In contrast, a MEMS pressure sensor that generates electronic output can take readings continuously under dynamic conditions in nearly real time. In order to use stainless-steel tubing for pressure measurements, it is necessary to clean many tubes, cut them to length, carefully install them, delicately deburr them, and splice them. A cluster of a few hundred 1/16-in.- (approx.=1.6-mm-) diameter tubes (such clusters are common in research testing facilities) can be several inches (of the order of 10 cm) in diameter and could weigh enough that two technicians are needed to handle it. Replacing hard tubing with electronic chips can eliminate much of the bulk. Each sensor would fit on the tip of a 1/16-in. tube with room to spare. The Lucas NovaSensor P592 piezoresistive silicon pressure sensor was chosen for this project because of its cost, availability, and tolerance to extreme ambient conditions. The sensor chip is 1 mm square by 0.6 mm thick (about 0.039 by 0.039 by 0.024 in.) and includes 0.12-mm (approx.=0.005-in.) wire connection tabs. The figure shows a flow-angularity probe that was built by use of three such MEMS chips. It is planned to demonstrate this MEMS probe as an alternative to a standard tube-type "Cobra" probe now used routinely in wind tunnels and aeronautical hardware. This MEMS probe could be translated across a flow field by use of a suitable actuator, so that its accuracy and the shortness of its response time could be exploited to obtain precise dynamic measurements of a sort that cannot be made by use of conventional tubing-based instrumentation.

Redding, Chip↗

NASA NTRS2013

Properties of Cathodoluminescence for Cryogenic Applications of SiO2-based Space Observatory Optics and Coatings

Disordered thin film SiO2SiOx coatings undergoing electron-beam bombardment exhibit cathodoluminescence, which can produce deleterious stray background light in cryogenic space-based astronomical observatories exposed to high-energy electron fluxes from space plasmas. As future observatory missions push the envelope into more extreme environments and more complex and sensitive detection, a fundamental understanding of the dependencies of this cathodoluminescence becomes critical to meet performance objectives of these advanced space-based observatories. Measurements of absolute radiance and emission spectra as functions of incident electron energy, flux, and power typical of space environments are presented for thin (60-200 nm) SiO2SiOx optical coatings on reflective metal substrates over a range of sample temperatures (40-400 K) and emission wavelengths (260-5000 nm). Luminescent intensity and peak wavelengths of four distinct bands were observed in UVVISNIR emission spectra, ranging from 300 nm to 1000 nm. A simple model is proposed that describes the dependence of cathodoluminescence on irradiation time, incident flux and energy, sample thickness, and temperature.

electron-beam bombardment↗

NASA NTRS1973

The development and demonstration of hybrid programmable attitude control electronics

In the course of extended life attitude control system (ELACS) research sponsored by NASA a hybrid programable attitude control electronics (HYPACE) concept was developed and demonstrated. The wide variety of future planetary missions demanded a new control approach to accommodate the automatic fault tolerance and long the life requirements of such missions. HYPACE provides an adaptable, analog/digital design approach that permits preflight and in-flight accommodation of mission changes, component performance variations, and spacecraft changes, through programing. This enabled broad multimission flexibility of application in a cost effective manner. Previously, flight control computers have not been not flown on planetary missions because of weight and power problems. These problems were resolved in the design of HYPACE. The HYPACE design, which was demonstrated in breadboard form on a single-axis gas-bearing spacecraft simulation, uses a single control channel to perform the attitude control functions sequentially, thus significantly reducing the number of component parts over hard-wired designs.

Smith, L. S.↗

NASA NTRS1982

A real-time dynamic spacecraft simulator for the LANDSAT-D mission

A real time dynamic simulator for LANDSAT D was developed and has played an integral role in the development and validation of both the ground control system and of the on-board flight software. The simulator utilized an electronic replica of the spacecraft on-board computer and data handling hardware interfaced to a VAX 11/780 computer and simulation software. Key features of the simulator design are a modular software architecture tailored to the VAX/VMS real time capabilities, a microprocessor controlled interface between the VAX and the flight hardware replica, complete simulation of the spacecraft and NASA network communication links, and a flexible and powerful scenario structuring and operator control capability. The design goals and trade-offs, software, and hardware design are summarized. The application of the simulator to the validation of both the ground systems and on-board software is reviewed in detail.

Coffin, A. R.↗

NASA NTRS1981

Impact of VLSI/VHSIC on satellite on-board signal processing

Forecasted improvements in IC fabrication techniques, such as the use of X-ray lithography, are expected to yield submicron circuit feature sizes within the decade of the 1980s. As dimensions decrease, reliability, cost, speed, power consumption and density improvements will be realized which have a significant impact on the capabilities of onboard spacecraft signal processing functions. This will in turn result in increases of the intelligence that may be deployed on spaceborne remote sensing platforms. Among programs oriented toward such goals are the silicon-based Very High Speed Integrated Circuit (VHSIC) researches sponsored by the U.S. Department of Defense, and efforts toward the development of GaAs devices which will compete with silicon VLSI technology for future applications. GaAs has an electron mobility which is five to six times that of silicon, and promises commensurate computation speed increases under low field conditions.

Aanstoos, J. V.↗

NASA NTRS1994

Probing the chemistry of nickel/metal hydride battery cells using electrochemical impedance spectroscopy

Electrochemical Impedance Spectroscopy (EIS) is a valuable tool for investigating the chemical and physical processes occurring at electrode surfaces. It offers information about electron transfer at interfaces, kinetics of reactions, and diffusion characteristics of the bulk phase between the electrodes. For battery cells, this technique offers another advantage in that it can be done without taking the battery apart. This non-destructive analysis technique can thus be used to gain a better understanding of the processes occurring within a battery cell. This also raises the possibility of improvements in battery design and identification or prediction of battery characteristics useful in industry and aerospace applications. EIS as a technique is powerful and capable of yielding significant information about the cell, but it also requires that the many parameters under investigation can be resolved. This implies an understanding of the processes occurring in a battery cell. Many battery types were surveyed in this work, but the main emphasis was on nickel/metal hydride batteries.

Isaac, Bryan J.↗

NASA NTRS1999

Space Solar Power: Satellite Concepts

Space Solar Power (SSP) applies broadly to the use of solar power for space related applications. The thrust of the NASA SSP initiative is to develop concepts and demonstrate technology for applying space solar power to NASA missions. Providing power from satellites in space via wireless transmission to a receiving station either on earth, another celestial body or a second satellite is one goal of the SSP initiative. The sandwich design is a satellite design in which the microwave transmitting array is the front face of a thin disk and the back of the disk is populated with solar cells, with the microwave electronics in between. The transmitter remains aimed at the earth in geostationary orbit while a system of mirrors directs sunlight to the photovoltaic cells, regardless of the satellite's orientation to the sun. The primary advantage of the sandwich design is it eliminates the need for a massive and complex electric power management and distribution system for the satellite. However, it requires a complex system for focusing sunlight onto the photovoltaic cells. In addition, positioning the photovoltaic array directly behind the transmitting array power conversion electronics will create a thermal management challenge. This project focused on developing designs and finding emerging technology to meet the challenges of solar tracking, a concentrating mirror system including materials and coatings, improved photovoltaic materials and thermal management.

Little, Frank E.↗

NASA NTRS2008

The New Anechoic Shielded Chambers Designed for Space and Commercial Applications at LIT

The main objective of this paper is to present the capabilities of the new anechoic shielded rooms designed for space and commercial applications as part of the Integration and Testing Laboratory (LIT, Laboratorio de Integracao e Testes) in Brazil. A new anechoic shielded room named CBA2 has been in full operation since March 2007 and a remodeled chamber CBA1 is planned to be ready by the end of 2008, replacing an old facility which was in operation for the last 18 years. The Brazilian Space Program started with very small and simple satellites and the old CBA1 chamber was conceived in 1987 to accomplish the EMI/EMC tests not requiring significant volumes. Since the very beginning this facility was also used by the private sector for other applications mainly due to the absorption of digital electronics in all kind of products. The intense use of this facility during the last years, operating three shifts a day, caused a normal degradation and imposed several limitations. Therefore, a new totally remodeled chamber was designed considering the state of the art in terms of absorbers and associated instrumentation. On the other hand the facility CBA2 was conceived, designed and implemented to test large satellites taking into account the advance of the technology in terms of RF frequencies, power level, testing methodologies and several other factors. A very interesting and unique aspect of this project was the partnership between the private sector and governmental institution. As a result, the total investment was shared between several companies and consequently a time-sharing use of the facility as well.

da Silva, Benjamim↗

NASA NTRS2006

Lunar Metal Oxide Electrolysis with Oxygen and Photovoltaic Array Production Applications

This paper presents the results of a Marshall Space Flight Center funded effort to conduct an experimental demonstration of the processing of simulated lunar resources by the molten oxide electrolysis (MOE) process to produce oxygen and metal from lunar resources to support human exploration of space. Oxygen extracted from lunar materials can be used for life support and propellant, and silicon and metallic elements produced can be used for in situ fabrication of thin-film solar cells for power production. The Moon is rich in mineral resources, but it is almost devoid of chemical reducing agents, therefore, molten oxide electrolysis, MOE, is chosen for extraction, since the electron is the most practical reducing agent. MOE was also chosen for following reasons. First, electrolytic processing offers uncommon versatility in its insensitivity to feedstock composition. Secondly, oxide melts boast the twin key attributes of highest solubilizing capacity for regolith and lowest volatility of any candidate electrolytes. The former is critical in ensuring high productivity since cell current is limited by reactant solubility, while the latter simplifies cell design by obviating the need for a gas-tight reactor to contain evaporation losses as would be the case with a gas or liquid phase fluoride reagent operating at such high temperatures. In the experiments reported here, melts containing iron oxide were electrolyzed in a low temperature supporting oxide electrolyte (developed by D. Sadoway, MIT). The production of oxygen and reduced iron were observed. Electrolysis was also performed on the supporting electrolyte with JSC-1 Lunar Simulant. The cell current for the supporting electrolyte alone is negligible while the current for the electrolyte with JSC-1 shows significant current and a peak at about -0.6 V indicating reductive reaction in the simulant.

Curreri, P. A.↗

NASA NTRS1992

Monitoring Subsystem For Testing Bearings

Electronic monitoring subsystem designed to be used in conjunction with controlling subsystem described in article, "Stepping-Motion Motor-Control Subsystem For Testing Bearings" (GSC-13418). Gathers data used to evaluate performance of bearing motor or other rotary mechanism being tested by subjecting it to stepping motions like those in its intended application. Data gathered at rate high enough to characterize dynamic properties of mechanism.

Powers, Charles E.↗

NASA NTRS2009

Distributed Control Architecture for Gas Turbine Engine

The transformation of engine control systems from centralized to distributed architecture is both necessary and enabling for future aeropropulsion applications. The continued growth of adaptive control applications and the trend to smaller, light weight cores is a counter influence on the weight and volume of control system hardware. A distributed engine control system using high temperature electronics and open systems communications will reverse the growing trend of control system weight ratio to total engine weight and also be a major factor in decreasing overall cost of ownership for aeropropulsion systems. The implementation of distributed engine control is not without significant challenges. There are the needs for high temperature electronics, development of simple, robust communications, and power supply for the on-board electronics.

Dennis Culley↗

NASA NTRS2012

An Inter-Comparison of Two Independent Site Test Interferometers Located in Goldstone, California: Initial Study Results

Site Test Interferometers (STIs) have been deployed at two different locations at the NASA Deep Space Network (DSN) tracking complex in Goldstone, California. An STI measures the difference in path length between a geostationary satellite and two antennas on the Earth, producing a measure of atmospheric phase fluctuations over spatial distances comparable to those between elements of possible microwave phased arrays. The purposes of the Goldstone STIs are to assess the suitability of Goldstone as an array site and to statistically characterize atmospheric induced delay fluctuations for application to future array scenarios.The two STI's are separated by 13 km across the Goldstone complex. Each instrument is composed of two small-diameter antennas and associated electronics separated by approx. 200 meters in a principally east-west configuration. The antennas continuously observe signals emitted by geo-stationary satellites and produce data that contain information on the phase difference between signals received by both antennas. The fluctuation in delay (or path length difference) statistics derived from these data sets can be used to infer power loss for particular array configurations.We report on a comparison of the root mean square (RMS) phase delay statistics estimated over 10-minute intervals between the two Goldstone STIs. We have achieved good statistical agreement between the data acquired from the two STIs, given that each instrument is observing different satellites, at different frequencies, over different baseline lengths, with very different implementations, and are located 13 km apart in widely separated terrain at different geodetic altitudes.

propagation↗

NASA NTRS1980

Application of fiber optics in spacecraft

The unique requirements placed on an optical fiber data system in space are briefly reviewed in this paper. These include temperature extremes, particle radiation, and, in some cases, a stringent electrical power budget. An overriding need is for the best possible reliability. Results related to the power consumption of a fiber terminal pair are reported, with the conclusion that a 32-port transmission star bus configuration could be operated error-free at 10 Mbits/s on 1/8 watt per transmitting terminal. The design of a transmitter terminal optimized for low idling power consumption is discussed. Although the electronic elements on a spacecraft are protected, the fiber cable may be subjected to large temperature extremes. Measured effects of temperature on fibers and cables are discussed and related to bus design. Radiation effects are briefly reviewed, with special reference to the long-duration low dose rate environment of a spacecraft.

Johnston, A. R.↗

NASA NTRS2008

NASA Tech Briefs, May 2008

Topics covered inclde: Deployable Wireless Camera Penetrators; Hand-Held Units for Short-Range Wireless Biotelemetry; Wearable Wireless Telemetry System for Implantable BioMEMS Sensors; Electronic Escape Trails for Firefighters; Architecture for a High-to-Medium-Voltage Power Converter; 24-Way Radial Power Combiner/Divider for 31 to 36 GHz; Three-Stage InP Submillimeter-Wave MMIC Amplifier; Fast Electromechanical Switches Based on Carbon Nanotubes; Solid-State High-Temperature Power Cells; Fast Offset Laser Phase-Locking System; Fabricating High-Resolution X-Ray Collimators; Embossed Teflon AF Laminate Membrane Microfluidic Diaphragm Valves; Flipperons for Improved Aerodynamic Performance; System Estimates Radius of Curvature of a Segmented Mirror; Refractory Ceramic Foams for Novel Applications; Self-Deploying Trusses Containing Shape-Memory Polymers; Fuel-Cell Electrolytes Based on Organosilica Hybrid Proton Conductors; Molecules for Fluorescence Detection of Specific Chemicals; Cell-Detection Technique for Automated Patch Clamping; Redesigned Human Metabolic Simulator; Compact, Highly Stable Ion Atomic Clock; LiGa(OTf)(sub 4) as an Electrolyte Salt for Li-Ion Cells; Compact Dielectric-Rod White-Light Delay Lines; Single-Mode WGM Resonators Fabricated by Diamond Turning; Mitigating Photon Jitter in Optical PPM Communication; MACOS Version 3.31; Fiber-Optic Determination of N2, O2, and Fuel Vapor in the Ullage of Liquid-Fuel Tanks; Spiking Neurons for Analysis of Patterns; Symmetric Phase-Only Filtering in Particle-Image Velocimetry; Efficient Coupler for a Bessel Beam Dispersive Element; and Attitude and Translation Control of a Solar Sail Vehicle.

Source record↗

NASA NTRS2014

Iodine Hall Thruster Propellant Feed System for a CubeSat

There has been significant work recently in the development of iodine-fed Hall thrusters for in-space propulsion applications.1 The use of iodine as a propellant provides many advantages over present xenon-gas-fed Hall thruster systems. Iodine is a solid at ambient temperature (no pressurization required) and has no special handling requirements, making it safe for secondary flight opportunities. It has exceptionally high ρI sp (density times specific impulse), making it an enabling technology for small satellite near-term applications and providing system level advantages over mid-term high power electric propulsion options. Iodine provides thrust and efficiency that are comparable to xenonfed Hall thrusters while operating in the same discharge current and voltage regime, making it possible to leverage the development of flight-qualified xenon Hall thruster power processing units for the iodine application. Work at MSFC is presently aimed at designing, integrating, and demonstrating a flight-like iodine feed system suitable for the Hall thruster application. This effort represents a significant advancement in state-of-the-art. Though Iodine thrusters have demonstrated high performance with mission enabling potential, a flight-like feed system has never been demonstrated and iodine compatible components do not yet exist. Presented in this paper is the end-to-end integrated feed system demonstration. The system includes a propellant tank with active feedback-control heating, fill and drain interfaces, latching and proportional flow control valves (PFCV), flow resistors, and flight-like CubeSat power and control electronics. Hardware is integrated into a CubeSat-sized structure, calibrated and tested under vacuum conditions, and operated under under hot-fire conditions using a Busek BHT-200 thruster designed for iodine. Performance of the system is evaluated thorugh accurate measurement of thrust and a calibrated of mass flow rate measurement, which is a function of reservoir temperature/pressure, the flow resistors, and the setting of the PFCV. The calibration is performed using independent flow control monitoring techniques, providing an in situ measure of the flowrate as a function of controllable parameters. The reservoir temperature controls the iodine sublimation rate, providing propellant to ths thruster by pressurizing the propellant feed system to approx.1-2 psi. Control of the temperature and the PFCV are used to maintain reservoir pressure and keep the thruster discharge current constant.

Polzin, Kurt A.↗

NASA NTRS1974

A mass spectrometric system for analyzing thermal desorption spectra of ion-implanted argon and cesium in tungsten

A mass spectrometric system for determining the characteristics of materials used in instrumental development and aerospace applications was developed. The desorption spectra of cesium that was ion-implanted into polycrystalline tungsten and the effects on the spectra of bombardment of the tungsten by low energy (70 eV) electrons were investigated. Work function changes were measured by the retarding potential diode method. Flash desorption characteristics were observed and gas-reaction mechanisms of the surface of heated metal filaments were studied. Desorption spectra were measured by linearly increasing the sample temperature at a selected rate, the temperature cycling being generated from a ramp-driven dc power supply, with the mass spectrometer tuned to a mass number of interest. Results of the study indicate an anomolous desorption mechanism following an electron bombardment of the sample surface. The enhanced spectra are a function of the post-bombardment time and energy and are suggestive of an increased concentration of cesium atoms, up to 10 or more angstroms below the surface.

Wood, G. M., Jr.↗

NASA NTRS1971

Beta Absorption Mass Monitoring of Particulates - A Review

The theory and application of beta-radiation absorption for the measurement and monitoring of airborne particulates are discussed. The use of this technique, both for source testing and for ambient air quality monitoring is reviewed. Various particle collection methods used in conjunction with beta absorption sensing configurations are considered. State of the art and current developments of instrumentation approaches for the automated measurement of mass concentration and size distribution of aerosols by beta absorption are discussed. Methods for electronic signal processing and recording are presented. The Beta absorption technique appears as a powerful tool for the unattended measurement of the mass of particulate pollution, compatible with telemetry and central data processing methods.

Lilienfeld, Pedro↗

NASA NTRSDate not supplied

Incorporating ADAPT-VQE with a Sparse Wavefunction Circuit Simulator to Find Compact Quantum Circuits for Chemical Applications

We implemented the ADAPT-VQE algorithm into our recent classical sparse wavefunction circuit simulator to demonstrate that classical resources can (1) efficiently find a physically motivated compact wavefunction ansatz for further refinement on near-term quantum hardware and (2) benchmark expected results of VQE-based algorithms once the quantum hardware is available to study large-scale applications. In particular, we study the role of the ADAPT-VQE operator pool, molecular basis set selection, and variations such as TETRIS-ADAPT-VQE on the performance of our classical circuit simulator. This work demonstrates the promise of using classical resources to generate highly accurate wavefunctions that can be prepared on quantum hardware to initiate other quantum algorithms such as phase estimation. Our approach harnesses the power of high-performance computing resources with the more limited available quantum computers to map a path toward quantum advantage for electronic structure calculations in chemistry and materials science.

Quantum Computing↗