SEARCH · Engineering Papers

Results for “airfoil”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Analysis of viscous transonic flow over airfoil sections

A full Navier-Stokes solver has been used to model transonic flow over three airfoil sections. The method uses a two-dimensional, implicit, conservative finite difference scheme for solving the compressible Navier-Stokes equations. Results are presented as prescribed for the Viscous Transonic Airfoil Workshop to be held at the AIAA 25th Aerospace Sciences Meeting. The NACA 0012, RAE 2822 and Jones airfoils have been investigated for both attached and separated transonic flows. Predictions for pressure distributions, loads, skin friction coefficients, boundary layer displacement thickness and velocity profiles are included and compared with experimental data when possible. Overall, the results are in good agreement with experimental data.

Huff, Dennis L.↗

NASA NTRS1987

Use of a liquid-crystal, heater-element composite for quantitative, high-resolution heat transfer coefficients on a turbine airfoil, including turbulence and surface roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at roon temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, Steven A.↗

NASA NTRS1987

Computation of full-coverage film-cooled airfoil temperatures by two methods and comparison with high heat flux data

Two methods were used to calculate the heat flux to full-coverage film cooled airfoils and, subsequently, the airfoil wall temperatures. The calculated wall temperatures were compared to measured temperatures obtained in the Hot Section Facility operating at real engine conditions. Gas temperatures and pressures up to 1900 K and 18 atm with a Reynolds number up to 1.9 million were investigated. Heat flux was calculated by the convective heat transfer coefficient adiabatic wall method and by the superposition method which incorporates the film injection effects in the heat transfer coefficient. The results of the comparison indicate the first method can predict the experimental data reasonably well. However, superposition overpredicted the heat flux to the airfoil without a significant modification of the turbulent Prandtl number. The results suggest that additional research is required to model the physics of full-coverage film cooling where there is significant temperature/density differences between the gas and the coolant.

Gladden, H. J.↗

NASA NTRS1987

Application of digital holographic interferometry to pressure measurements of symmetric, supercritical and circulation-control airfoils in transonic flow fields

Six airfoil interferograms were evaluated using a semiautomatic image-processor system which digitizes, segments, and extracts the fringe coordinates along a polygonal line. The resulting fringe order function was converted into density and pressure distributions and a comparison was made with pressure transducer data at the same wind tunnel test conditions. Three airfoil shapes were used in the evaluation to test the capabilities of the image processor with a variety of flows. Symmetric, supercritical, and circulation-control airfoil interferograms provided fringe patterns with shocks, separated flows, and high-pressure regions for evaluation. Regions along the polygon line with very clear fringe patterns yielded results within 1% of transducer measurements, while poorer quality regions, particularly near the leading and trailing edges, yielded results that were not as good.

Torres, Francisco J.↗

NASA NTRS1987

Improved algorithms for circulation-control airfoils in transonic flow

A zonal model for aerodynamic analysis of two-dimensional transonic circulation control airfoils has been developed. The present approach combines a transonic full potential method for the global flow field and an integral boundary layer method for regions of the airfoil excluding the wall jet with a parabolized Navier-Stokes code for resolving the wall jet region beyond the slot. Existing methods suffer from two deficiencies: the insensitivity of the calculation to small changes in the Coanda surface geometry; and the inability to predict the shock structure of the underexpanded supersonic wall jets. The present wall jet procedure involves a pressure-split approach in the streamwise sense to enable noniterative solution of the coupled continuity and normal momentum equations for increased surface sensitivity and allows for expansion of applications to sonic slot exit conditions. Encouraging results are obtained in comparison with experimental data for two circulation airfoils with subsonic wall jets.

Dvorak, Frank A.↗

NASA NTRS1987

Numerical simulation by TVD schemes of complex shock reflections from airfoils at high angle of attack

The shock-capturing capability of total variation diminishing (TVD) schemes is demonstrated for a more realistic complex shock-diffraction problem for which the experimental data are available. Second-order explicit upwind and symmetric TVD schemes are used to solve the time-dependent Euler equations of gas dynamics for the interaction of a blast wave with an airfoil at high angle-of-attack. The test cases considered are a time-dependent moving curved-shock wave and a contant moving planar-shock wave impinging at an angle-of-attack 30 deg on a NACA 0018 airfoil. Good agreement is obtained between isopycnic contours computed by the TVD schemes and those from experimental interferograms. No drastic difference in flow-field structure is found between the curved- and planar-shock wave cases, except for a difference in density level near the lower surface of the airfoil. Computation for cases with higher shock Mach numbers is also possible. Numerical experiments show that the symmetric TVD scheme is less sensitive to the boundary conditions treatment than the upwind scheme.

Moon, Young J.↗

NASA NTRS1986

A summary of the effects of Reynolds number on drag divergence for airfoils tested in the Langley 0.3-meter transonic cryogenic tunnel

The direct first order effect of Reynolds number on the determination of drag-divergence conditions is summarized for six airfoils which were tested in the Langley 0.3-Meter Transonic Cryogenic Tunnel. A second order effect, derived through the effect of Reynolds number on the sidewall boundary layer, is included. In addition, a comparison of how the drag divergence condition is affected on going from one class of airfoil to another is presented. The drag-divergence condition is affected first order by Reynolds number for each of the six airfoils and of course all data are affected second order, since the presence of the boundary layer necessitates a sidewall correction.

Jenkins, Renaldo V.↗

NASA NTRS1987

Analysis of viscous transonic flow over airfoil sections

Huff, Dennis L.↗

NASA NTRS1987

Numerical simulations of unsteady airfoil-vortex interactions

Numerical methods based on the thin layer Navier-Stokes, Euler and transonic small disturbance equations, all three of which use the perturbation form of an implicit numerical algorithm, are used to formulate the unsteady interactions of a moving vortex with a stationary airfoil. Results are presented for both transonic and subsonic flows, as well as for weak and strong interactions. In general, the results exhibit an overwhelming influence of the vortex on the flow field around the airfoil, especially when the convecting vortex is within one chord of the airfoil. It is noted that even the ostensibly weak interactions produced vortex/shock-induced boundary layer separation.

Srinivasan, G. R.↗

NASA NTRS1987

A unique measurement technique to study laminar-separation bubble characteristics on an airfoil

A 'nonintrusive', multielement heat-transfer sensor was designed to study laminar-separation bubble characteristics on a NASA LRN (1)-1010 low-Reynolds number airfoil. The sensor consists of 30 individual nickel films, vacuum-deposited on a thin substrate (0.05 mm) that was bonded to the airfoil model with the sensor array placed streamwise on the airfoil upper surface. Experiments were conducted on a 15-cm chord model in the 50,000-300,000 chord Reynolds number range. Time history as well as spectral analysis of signals from surface film gauges were simultaneously obtained to determine the location of laminar separation and the subsequent behavior of the separated shear layer. In addition to the successful determination of laminar separation, a new phenomenon involving a large phase shift in dynamic shear stresses across the separation and reattachment points was observed.

Stack, J. P.↗

NASA NTRS1987

An airfoil designed for a high-altitude, long endurance remotely piloted vehicle

The preliminary design of high-altitude, long-endurance RPVs is complicated by the paucity of data concerning airfoils with high lift coefficients at low Re numbers. Attention is presently given to a generic airfoil of this type for the design Re number range of 700,000 to 2 million. Low drag is predicted for lift coefficients from 0.4 (for high speed dashes) to 1.5 (for maximum mission endurance). The airfoil is such that its maximum lift coefficient, at 1.8, is unaffected by the surface contamination that would be encountered during takeoffs and landings in rain or over insect-infested runways.

Maughmer, Mark D.↗

NASA NTRS1987

Visualization of the laminar separation bubble on airfoils at low Reynolds numbers

The use of the smoke tube and titanium tetrachloride techniques in the study of low Reynolds number flow about two different airfoils is presented. Emphasis is placed on the problems of determining the characteristics of laminar separation bubbles occurring on the Wortmann FX63-137 airfoil and the NACA 66(3)-018 airfoil. Comparisons are made with the hot-wire technique and the use of kerosene vapor.

Mueller, T. J.↗

NASA NTRS1987

The structure of separated flow regions occurring near the leading edge of airfoils including transition

All the time and effort was directed toward acquiring, reducing, and analyzing more hot-wire anemometer data. Some static pressure distribution data were also acquired to support the analysis of the velocity profile data. Laser Doppler Velocimetry data were not acquired due to equipment problems. Included were seven combinations of chord Reynolds number, angle of attack, and acoustic forcing using the NACA 663-018 airfoil. This research has as its objective the detailed documentation of the structure and behavior of the transitional separation bubble and the redeveloping boundary layer after reattachment over an airfoil at low Reynolds numbers. The intent is to further the understanding of the complex flow phenomena so that analytic methods for predicting their formulation and development can be improved. These analytic techniques have applications in the design and performance prediction of airfoils operating in the low Reynolds number flight regime.

Mueller, Thomas J.↗

NASA NTRS1987

Potential flow around two-dimensional airfoils using a singular integral method

The problem of potential flow around two-dimensional airfoils is solved by using a new singular integral method. The potential flow equations for incompressible potential flow are written in a singular integral equation. The equation is solved at N collocation points on the airfoil surface. A unique feature of this method is that the airfoil geometry is specified as an independent variable in the exact integral equation. Compared to other numerical methods, the present calculation procedure is much simpler and gives remarkable accuracy for many body shapes. An advantage of the present method is that it allows the inverse design calculation and the results are extremely accurate.

Nguyen, Yves↗

NASA NTRS1986

Advanced natural laminar flow airfoil with high lift to drag ratio

An experimental verification of a high performance natural laminar flow (NLF) airfoil for low speed and high Reynolds number applications was completed in the Langley Low Turbulence Pressure Tunnel (LTPT). Theoretical development allowed for the achievement of 0.70 chord laminar flow on both surfaces by the use of accelerated flow as long as tunnel turbulence did not cause upstream movement of transition with increasing chord Reynolds number. With such a rearward pressure recovery, a concave type deceleration was implemented. Two-dimensional theoretical analysis indicated that a minimum profile drag coefficient of 0.0026 was possible with the desired laminar flow at the design condition. With the three-foot chord two-dimensional model constructed for the LTPT experiment, a minimum profile drag coefficient of 0.0027 was measured at c sub l = 0.41 and Re sub c = 10 x 10 to the 6th power. The low drag bucket was shifted over a considerably large c sub l range by the use of the 12.5 percent chord trailing edge flap. A two-dimensional lift to drag ratio (L/D) was 245. Surprisingly high c sub l max values were obtained for an airfoil of this type. A 0.20 chort split flap with 60 deg deflection was also implemented to verify the airfoil's lift capabilities. A maximum lift coefficient of 2.70 was attained at Reynolds numbers of 3 and 6 million.

Viken, Jeffrey K.↗

NASA NTRS1986

Airfoil large eddy breakup devices for turbulent drag reduction

It was determined from the present LaRC experiments that tandem, airfoil-shaped large eddy breakup (LEBU) devices can reduce local skin friction as much as 30 percent with a recovery region extending more than 100 boundary layer thicknesses downstream. These airfoils experience near laminar skin friction device drag and produce net drag reductions of up to 7 percent. In contrast to the thin plates used in previous experiments, these airfoils are more than 1000 time stiffer and hence have the potential to withstand the real flight environment (dynamic pressure 36 times larger than in low-speed wing tunnels). In addition, the higher Reynolds numbers of the present tests indicate drag reduction performance is at least as good (or better) as at lower Reynolds numbers.

Anders, J. B.↗

NASA NTRS1987

Navier-Stokes calculations and turbulence modeling in the trailing edge region of a circulation control airfoil

The accurate prediction of turbulent flows over curved surfaces in general and over the trailing edge region of circulation control airfoils in particular requires the coupled efforts of turbulence modelers, numerical analysts and experimentalists. The purpose of the research program in this area is described. Then, the influence on turbulence modeling of the flow characteristics over a typical circulation control wing is discussed. Next, the scope of this effort to study turbulence in the trailing edge region of a circulation control airfoil is presented. This is followed by a brief overview of the computation scheme, including the grid, governing equations, numerical method, boundary conditions and turbulence models applied to date. Then, examples of applications of two algebraic eddy viscosity models to the trailing edge region of a circulation control airfoil is presented. The results from the calculations is summarized, and conclusions drawn based on examples. Finally, the future directions of the program is outlined.

Viegas, John R.↗

NASA NTRS1988

Application of a nonisentropic full potential method to AGARD standard airfoils

An entropy-correction method for the unsteady full potential equation is presented. The unsteady potential equation is modified to model the entropy jumps across shock waves. The conservative form of the modified equation is solved in generalized coordinates using an implicit, approximate factorization method. A flux-biasing differencing method, which generates the proper amounts of artificial viscosity in supersonic regions, is used to discretize the flow equations in space. Calculated results are presented for the NLR 7301, NACA 0012, and NACA 64A010A airfoils. Comparisons of the present method and solutions of the Euler equations are presented for the NLR 7301 airfoil, and comparisons of the present method and experimental data are presented for all three airfoils. The comparisons show that the present method more accurately models solutions of the Euler equations and experiment than does the isentropic potential formulation. In addition, it is shown that modeling shock-generated entropy extends the range of validity of the full potential method.

Whitlow, Woodrow, Jr.↗