SEARCH · Engineering Papers

Results for “WAVEGUIDES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Multifrequency broadband polarized horn antenna

A corrugated conical horn antenna is simultaneously fed a multiplicity of signals, two for each of five frequencies, with each of a pair of signals fed in each of two orthogonal planes for excitation of a desired spherical hybrid mode. The lowest frequency is fed into the horn through orthogonal pairs of colinear slots, each pair being fed by coaxial tee power dividers. Other signals are fed through a circular waveguide connected to the vertex. The highest frequency signals are fed through orthogonal ports near the far end of the circular waveguide. The intermediate frequency signals are fed through orthogonal ports spaced along the waveguide. Filtering is incorporated for each to maintain isolation and low insertion loss.

Green, K. A.↗

NASA NTRS1981

Investigation of direct integrated optics modulators

Direct optical modulation techniques applicable to integrated optical data preprocessors were studied. Emphasis was placed on the analysis and fabrication of a field effect type modulator. A series of computer modeling studies were performed to determine the effects of semiconductor cladding on the fields of propagating waves in planar dielectric waveguides. These studies predicted that changes in the propagation characteristics of waveguides clad with silicon and gallium arsenide could be made large enough to be useful in modulators. These effects are dependent on the complex permittivity and thickness of the cladding. Since the conductivity of the cladding can be changed by the photon generation of hole-electron pairs, incoherent light may be used as the input to modulate a coherent light beam. Waveguides were fabricated and silicon claddings were applied to verify the theoretical predictions.

Batchman, T. E.↗

NASA NTRS1980

SPS antenna element evaluation

The SPS transmitting array requires an architecture which will provide a low weight, high efficiency and high structural rigidity. Waveguide slot arrays constitute the most desirable option. Consequently, such an array was chosen for the SPS. Waveguide slot arrays offer high efficiency, uniform illumination, and are fairly lightweight. Bandwidths of such arrays are narrow, typically 1/2-2%. Although this does not directly impact the SPS, which transmits power at a single frequency of 2.45 GHz, the narrow bandwidth does constrain the thermal and mechanical tolerances of the antenna. The purpose of this program is to better define the electronic aspects of an SPS specific waveguide slot array. The specific aims of the program are as follows: (1) To build a full-scale half-module, 10 stick, array, the design parameters for which are to be determined analytical considerations tempered by experimental data on a single slotted radiating stick, (2) To experimentally evaluate the completed array with respect to antenna pattern, impedance and return loss; and (3) To measure swept transmission amplitude and phase to provide a data base for design of a receiving antenna.

Lunden, C. D.↗

NASA NTRS1980

Evaluation of thick wall wave guide element

The SPS transmitting array requires an architecture which will provide a low weight, high efficiency and high structural rigidity. As noted above, waveguide slot arrays constitute the most desirable option. Consequently, such an array has been chosen for the SPS. Waveguide slot arrays offer high efficiency, uniform illumination, are are fairly lighweight. Bandwidths of such arrays are narrow, typically 1/2-2%. Although this does not directly impact the SPS, which transmits power at a single frequency of 2.45 GHz, the narrow bandwidth does constrain the thermal and mechanical tolerances of the antenna. The purpose of this program is to better define the electronic aspects of an SPS specific waveguide slot array. The specific aims of the program are as follows: (1) To build a full-scale half-module, 10 stick, array, the design parameters for which are to be determined by analytical considerations tempered by experimental data on a single slotted radiating stick, (2) To experimentally evaluate the completed array with respect to antenna pattern, impedance and return loss, and (3) To measure swept transmission amplitude and phase to provide a data base for design of a receiving antenna.

Nalos, E. J.↗

NASA NTRS1981

Planar Rowland spectrometer for fiber-optic wavelength demultiplexing

A planar Rowland spectrometer was fabricated and characterized as a wavelength demultiplexer for multimode fiber-optic applications. The spectrometer consisted of a planar multimode glass waveguide with two curved end faces and a cylindrical concave attached to one of the end faces. Semiconductor lasers with wavelengths between 0.825 and 0.845 micron were used for the measurements. Cross-talk isolation between two adjacent fibers with center-to-center separation of 175 microns (100 A in wavelength difference) was measured to be 18 dB. The device's performance was limited by grating diffraction efficiency, optical aberration, waveguide dispersion, and waveguide losses.

Yen, H. W.↗

NASA NTRS1984

K-Band Latching Switches

Design, development, and tests are described for two single-pole-double-throw latching waveguide ferrite switches: a K-band switch in WR-42 waveguide and a Ka-band switch in WR-28 waveguide. Both switches have structurally simple junctions, mechanically interlocked without the use of bonding materials; they are impervious to the effects of thermal, shock, and vibration stresses. Ferrite material for the Ka-band switch with a proper combination of magnetic and dielectric properties was available and resulted in excellent low loss, wideband performance. The high power handling requirement of the K-band switch limited the choice of ferrite to nickel-zinc compositions with adequate magnetic properties, but with too low relative dielectric constant. The relative dielectric constant determines the junction dimensions for given frequency responses. In this case the too low value unavoidably leads to a larger than optimum junction volume, increasing the insertion loss and restricting the operating bandwidth. Efforts to overcome the materials-related difficulties through the design of a composite junction with increased effective dielectric properties efforts to modify the relative dielectric constant of nickel-zinc ferrite are examined.

Piotrowski, W. S.↗

NASA NTRS1984

Numerical methods for analyzing electromagnetic scattering

The wave attenuation in a cylindrical waveguide coated with lossy dielectric material was studied. The scope was extended to the high frequency case for calculating attenuation coefficients and propagation constants of a dielectric coated circular waveguide. The magnetic material coating was studied. At low frequency a one way 3dB attenuation was achieved within a longitudinal distance of one diameter. A software program was generated to plot the field patterns of the lowest 30 modes in the cylindrical waveguides.

Lee, S. W.↗

NASA NTRS1984

MMIC devices for active phased array antennas

The study of printed circuit discontinuities is necessary in order to design, for example, transitions between rectangular waveguides and printed circuits. New developments with respect to the analytical approaches to this problem are discussed. A summary of the progress in the experimental approach is presented. The accurate solution for the modes in various millimeter-wave waveguides is essential in the analysis of many integrated circuit components, such as filters and impedance transformers. Problems associated with the numerical computation of these modes in two frequently used waveguide forms, namely, the finline and microstrip, are presented. The spectral domain method of formulation, with a moment method solution, is considered. This approach can be readily extended to analyze an arbitrary configuration of dielectric and metallized regions in a shielded enclosure. Galerkin's method is used, where the testing and basic functions are the same. It is shown that the mode functions, or eigenfunctions, are more sensitive to errors than the phase constants, or eigenvalues. The approximate mode functions do not satisfy the orthogonality relationship well, resulting in difficulties when these modal solutions are used to form an approximate Green's function or are used in a mode matching analysis.

Mittra, R.↗

NASA NTRS1985

Interleaved array antenna technology development

This is the third phase of a program to establish an antenna concept for shuttle and free flying spacecraft earth resources experiments using Synthetic Aperture Radar. The feasibility of a plated graphite epoxy waveguide for a space antenna was evaluated. A quantity of flat panels and waveguides were developed, procured, and tested for electrical and mechanical properties. In addition, processes for the assembly of a unique waveguide array were investigated. Finally, trades between various configurations that would allow elevation (range) electronic scanning and that would minimize feed complexity for various RF bandwidths were made.

Source record↗

NASA NTRS1985

Analysis of the electromagnetic scattering from an inlet geometry with lossy walls

One of the primary goals is to develop an approximate but sufficiently accurate analysis for the problem of electromagnetic (EM) plane wave scattering by an open ended, perfectly-conducting, semi-infinite hollow circular waveguide (or duct) with a thin, uniform layer of lossy or absorbing material on its inner wall, and with a simple termination inside. The less difficult but useful problem of the EM scattering by a two-dimensional (2-D), semi-infinite parallel plate waveguide with an impedance boundary condition on the inner walls was chosen initially for analysis. The impedance boundary condition in this problem serves to model a thin layer of lossy dielectric/ferrite coating on the otherwise perfectly-conducting interior waveguide walls. An approximate but efficient and accurate ray solution was obtained recently. That solution is presently being extended to the case of a moderately thick dielectric/ferrite coating on the walls so as to be valid for situations where the impedance boundary condition may not remain sufficiently accurate.

Myung, N. H.↗

NASA NTRS1986

Passive Element Shapes Antenna Radiation Pattern

Parasitic waveguide element suppresses ground-reflected multipath radiation. Small section of waveguide placed in front of phased-array antenna operating at 850 MHz modifies radiation field by reducing power density parallel to and below ground plane without significantly affecting primary radiation at angles greater than 20 degrees above horizontal. Acts as parasitic radiator that shifts phase of portion of wavefront by approximately 180 degrees, causing partial cancellation in ground plane, thereby reducing radiation intensity in that direction by about 10 dB. Produces corresponding reduction in multipath radiation scattered from ground. Waveguide technique also used to decouple two nearby antennas.

Bonebright, M. E.↗

NASA NTRS1985

Numerical methods for analyzing electromagnetic scattering

Attenuation properties of the normal modes in an overmoded waveguide coated with a lossy material were analyzed. It is found that the low-order modes, can be significantly attenuated even with a thin layer of coating if the coating material is not too lossy. A thinner layer of coating is required for large attenuation of the low-order modes if the coating material is magnetic rather than dielectric. The Radar Cross Section (RCS) from an uncoated circular guide terminated by a perfect electric conductor was calculated and compared with available experimental data. It is confirmed that the interior irradiation contributes to the RCS. The equivalent-current method based on the geometrical theory of diffraction (GTD) was chosen for the calculation of the contribution from the rim diffraction. The RCS reduction from a coated circular guide terminated by a PEC are planned schemes for the experiments are included. The waveguide coated with a lossy magnetic material is suggested as a substitute for the corrugated waveguide.

Lee, S. W.↗

NASA NTRS1986

Features and technologies of ERS-1 (ESA) and X-SAR antennas

Features and technologies of planar waveguide array antennas developed for spaceborne microwave sensors are described. Such antennas are made from carbon fiber reinforced plastic (CFRP) employing special manufacturing and metallization techniques to achieve satisfactory electrical properties. Mechanical design enables deployable antenna structures necessary for satellite applications (e.g., ESA ERS-1). The slotted waveguide concept provides high aperture efficiency, good beamshaping capabilities, and low losses. These CFRP waveguide antennas feature low mass, high accuracy and stiffness, and can be operated within wide temperature ranges.

Schuessler, R.↗

NASA NTRS1986

Utilization of the Usuda Deep Space Center for the United States International Cometary Explorer (ICE)

The Usuda Deep Space Center, which supported the ICE mission by enhancing the telemetry capability, is described. An outline of the comet Giacobini-Zinner observation project is provided. Usuda performance with one receiver channel was comparable to, if not better than, that of the Goldstone 64-m antenna with the two channels combined. The Usuda beam waveguide system is analyzed and found to have many advantages over conventional waveguide systems. It is concluded that this experience with the Usuda beam waveguide will become an integral part of future DSN decision making processes.

Fanelli, N. A.↗

NASA NTRS1987

Stochastic model theory of broadband shock associated noise from supersonic jets

A method based on the work of Tam and Tanna (1982) for calculating the near field noise spectrum and the spatial distribution of broadband shock associated noise from supersonic jets is proposed. Multiple-scales expansion is used to decompose the quasi-periodic shock cells into time-independent waveguide modes of the jet flow, and the interaction of the instability waves with each of the waveguide modes is shown to generate unsteady disturbances which become part of the broadband shock associated noise when radiated to the far field. The observed broadband shock associated noise is composed of a superposition of the various distinct spectra of the different waveguide modes, and the multispectra can be easily identified in many of the existing far and near field noise measurements.

Tam, C. K. W.↗

NASA NTRS1987

Fiber optic gyro development at the Jet Propulsion Laboratory

A low-level, but continuing, fiber-gyro development activity has been carried on at the Jet Propulsion Laboratory since 1977. The activity was originated because of a recognition of the potential for low-cost high-performance gyros suitable for interplanetary spacecraft. An early decision was made to concentrate available resources on supporting the development of electrooptically active channel waveguide components which could be fabricated by mask diffusion processes. Titanium-indiffused lithium niobate waveguide components used at 0.83 micron wavelength were first tested and then abandoned because of instabilities caused by so-called optical damage. Components fabricated for use at 1.3-micron wavelength have proven to be stable. A gyro configuration concept based upon 1.3 micron channel waveguide components has evolved, and a baseline 1.3-micron all-fiber gyro has been assembled and tested.

Goss, Willis C.↗

NASA NTRS1991

Applications of a high power four-way power divider and combiner and a cross-over circuit

Circuits of rectangular waveguides coupled to a cylindrical cavity have been studied. Two types of circuits were developed: a high-power four-way power divider/combiner with less than 0.5 dB insertion loss over a 20 percent bandwidth and a high-power four-port cross-over circuit with less than 0.7 dB insertion loss and 20 dB isolation at X-band. To demonstrate the feasibility of the first circuit, a power combiner was built by connecting four Gunn oscillators to the four rectangular waveguide ports of the radial waveguide. A power combining efficiency of over 70 percent was achieved at X-band. The second circuit was used to feed a dual-polarization cross-slot antenna backed by a cylindrical cavity.

Chang, Kai↗

NASA NTRS1991

Length minimization design considerations in photonic integrated circuits incorporating directional couplers

Because directional couplers involve channel waveguides which are very close to one another, transition regions to regions where channel waveguides are widely separated are utilized. The total length of a directional coupler and transition regions can be minimized for a particular degree of field confinement. Calculations presented for LiNbO3-, GaAlAs-, and SiO2/Si-based optical channel waveguides demonstrate the presence of a minimum total length corresponding to a particular degree of field confinement. The overall length at the minimum is shown to be significantly lower than for other values of field confinement allowing single-mode operation. This implies that either more devices can be integrated on a substrate or that less material is needed for an integrated optical circuit.

Boyd, Joseph T.↗