Results for “Turbulence Stabilization” — Page 40

NASA NTRS1981

Piloted simulation of hover and transition of a vertical attitude takeoff and landing aircraft

Piloted simulation studies of candidate control systems for VATOL aircraft were conducted on a six degree of freedom simulator. Hover and transitions from wing-born to hovering flight were performed, with and without turbulence, on a representative high performance fighter configuration. Deflection of the rear engine nozzle provided pitch and yaw control moments in concert with reaction controls for roll. Unique motion cues in hover result from the vertical displacement of the cockpit and the thrust vectoring nozzles. Abundant control power available with moderate engine nozzle deflection combined with rate feedback for stability augmentation provided very satisfactory control.

Hill, G. C.↗

NASA NTRS1982

CO2 lidar for measurements of trace gases and wind velocities

CO2 lidar systems technology and signal processing requirements relevant to measurement needs and sensitivity are discussed. Doppler processing is similar to microwave radar, with signal reception controlled by a computer capable of both direct and heterodyne operations. Trace gas concentrations have been obtained with the NASA DIAL system, and trace gas transport has been determined with Doppler lidar measurements for wind velocity and turbulence. High vertical resolution measurement of trace gases, wind velocity, and turbulence are most important in the planetary boundary layer and in regions between the PBL and the lower stratosphere. Shear measurements are critical for airport operational safety. A sensitivity analysis for heterodyne detection with the DIAL system and for short pulses using a Doppler lidar system is presented. The development of transient injection locking techniques, as well as frequency stability by reducing chirp and catalytic control of closed cycle CO2 laser chemistry, is described.

Hess, R. V.↗

NASA NTRS1987

Boundary-layer instability mechanisms on a swept-leading edge at Mach 3.5

Correlations have been made in NASA Langley's Mach 3.5 Pilot Quiet Tunnel for the transitions occurring from laminar to turbulent flow, in the cases of 45-deg and 60-deg swept cylinders. While freestream noise variations had no effect on boundary layer transition, the addition of boundary layer trips to the leading edges led to transition at lower Re numbers, depending on both trip height and wind tunnel noise level. Also presented are the results of compressible linear stability calculations for the boundary layer of an infinite swept cylinder; Tollmien-Schlichting waves are found to be amplified in the attachment line boundary layer.

Creel, T. R., Jr.↗

NASA NTRS1996

The Use of Steady and Pulsed Detonations for Propulsion Systems

Objectives of the ODWE concept studies are: demonstrate the feasibility of the oblique detonation wave engine (ODWE) for hypersonic propulsion; demonstrate the existance and stability of an oblique detonation wave in hypersonic wind tunnels; develop engineering codes which predict the performance characteristics of the ODWE including specific impulse and thrust coefficients for various operating conditions; develop multi-dimensional computer codes which can model all aspects of the ODWE including fuel injection, mixing, ignition, combustion and expansion with fully detailed chemical kinetics and turbulence models; and validate the codes with experimental data use the simulations to predict the ODWE performance for conditions not easily obtained in wind tunnels.

Adelman, Henry G.↗

NASA NTRS1977

Acoustics-turbulence interaction

An investigation of the instability frequency was undertaken. Measurements revealed that the hot wire probe induces and sustains stable upstream oscillation of the free shear layer. The characteristics of the free shear layer tone are found to be different from the slit jet wedge edgetone phenomenon. The shear tone induced by a plane wedge in a plane free shear layer was then examined in order to further document the phenomenon. The eigenvalues and eigenfunctions of the tone fundamental show agreement with the spatial stability theory. A comprehensive summary of the results is also included.

Hussain, A. K. M. F.↗

NASA NTRS1989

A critical comparison of turbulence models for homogeneous shear flows in a rotating frame

A variety of turbulence models, including five second-order closure models and four two equation models, are tested for the problem of homogeneous turbulent shear flow in a rotating frame. The model predictions for the time evolution of the turbulent kinetic energy and dissipation rate, as well as those for the equilibrium states, are compared with the results of physical and numerical experiments. Most of the two-equation models predict the same results for all rotation rates (omega/S) in which there is an exponential time growth of the turbulent kinetic energy and dissipation rate. The second-order closures are qualitatively superior since, consistent with physical and numerical experiments, they only predict this type of unstable flow for intermediate rotation rates in the range -0.1 less than or equal to omega/S less than or equal to 1.6. For rotation rates outside this range, there is an exchange of stabilities with a solution whose kinetic energy and dissipation rate decay with time. Although the second-order closures are superior to the two-equation models, there are still problems with the quantitative accuracy of their predictions.

Speziale, Charles G.↗

NASA NTRS1989

A critical comparison of turbulence models for homogeneous shear flows in a rotating frame

A variety of turbulence models, including five second-order closure models and four two equation models, are tested for the problem of homogeneous turbulent shear flow in a rotating frame. The model predictions for the time evolution of the turbulent kinetic energy and dissipation rate, as well as those for the equilibrium states, are compared with the results of physical and numerical experiments. Most of the two-equation models predict the same results for all rotation rates (omega/S) in which there is an exponential time growth of the turbulent kinetic energy and dissipation rate. The second-order closures are qualitatively superior since, consistent with physical and numerical experiments, they only predict this type of unstable flow for intermediate rotation rates in the range -0.1 less than or equal to omega/S less than or equal to 1.6. For rotation rates outside this range, there is an exchange of stabilities with a solution whose kinetic energy and dissipation rate decay with time. Although the second-order closures are superior to the two-equation models, there are still problems with the quantitative accuracy of thier predictions.

Speziale, Charles G.↗

NASA NTRS1990

A critical comparison of turbulence models for homogeneous shear flows in a rotating frame

A variety of turbulence models, including five second-order closure models and four two equation models, are tested for the problem of homogeneous turbulent shear flow in a rotating frame. The model predictions for the time evolution of the turbulent kinetic energy and dissipation rate, as well as those for the equilibrium states, are compared with the results of physical and numerical experiments. Most of the two-equation models predict the same results for all rotation rates (omega/S) in which there is an exponential time growth of the turbulent kinetic energy and dissipation rate. The second-order closures are qualitatively superior since, consistent with physical and numerical experiments, they only predict this type of unstable flow for intermediate rotation rates in the range -0.1 less than or equal to omega/S less than or equal to 1.6. For rotation rates outside this range, there is an exchange of stabilities with a solution whose kinetic energy and dissipation rate decay with time. Although the second-order closures are superior to the two-equation models, there are still problems with the quantitative accuracy of their predictions.

Speziale, Charles G.↗

NASA NTRS1991

A laser velocimeter investigation of the normal shock-wave boundary layer interaction

Nonintrusive 3-D measurements were made of a normal shock wave/turbulent boundary layer interaction. The measurements were made through a quadrant of a square test section of a continuous flow supersonic wind tunnel in which a normal shock wave had been stabilized. Two dimensional measurements were made throughout the interaction region while 3-D measurements were made near the corner in the vicinity of the shock where 3-D flow effects were expected to be significant. Laser Doppler velocimetry, surface static pressure measurements, and flow visualization techniques were used for two freestream nominal Mach number test cases: 1.6 and 1.3. No turbulence information was obtained. The mean velocity measurements were converted to Mach number by recording the wind tunnel total temperature. Some shock oscillation was present during both of the test cases. After startup of the wind tunnel, the shock oscillated with an amplitude of approx. + or - 1 cm, however, after reaching steady condition, the shock oscillation amplitude was greatly reduced, as evidenced by the laser velocimeter results. The Mach 1.3 test case resulted in a nearly uniform flow without secondary shock waves and with no or very isolated corner separation.

Chriss, Randall M.↗

NASA NTRS1999

Modeling the Dynamics of Ensemble-Averaged Linear Disturbances in Homogeneous Shear Flow

In order to expand the predictive capability of single-point turbulence closure models to account for the early-stage transition regime, a methodology for the formulation and calibration of model equations for the ensemble-averaged disturbance kinetic energy and energy dissipation rate is presented. The calibration is based on homogeneous shear flow where disturbances can be described by rapid distortion theory (RDT). The relationship between RDT and linear stability theory is exploited in order to obtain a closed set of modeled equations. The linear disturbance equations are solved directly so that the numerical simulation yields a database from which the closure coefficients in the ensemble-averaged disturbance equations can be determined. Key words: transition/turbulence modeling, homogeneous shear, rapid distortion theory.

Thacker, W. D.↗

NASA NTRS2012

Secondary Instability of Second Modes in Hypersonic Boundary Layers

Second mode disturbances dominate the primary instability stage of transition in a number of hypersonic flow configurations. The highest amplification rates of second mode disturbances are usually associated with 2D (or axisymmetric) perturbations and, therefore, a likely scenario for the onset of the three-dimensionality required for laminar-turbulent transition corresponds to the parametric amplification of 3D secondary instabilities in the presence of 2D, finite amplitude second mode disturbances. The secondary instability of second mode disturbances is studied for selected canonical flow configurations. The basic state for the secondary instability analysis is obtained by tracking the linear and nonlinear evolution of 2D, second mode disturbances using nonlinear parabolized stability equations. Unlike in previous studies, the selection of primary disturbances used for the secondary instability analysis was based on their potential relevance to transition in a low disturbance environment and the effects of nonlinearity on the evolution of primary disturbances was accounted for. Strongly nonlinear effects related to the self-interaction of second mode disturbances lead to an upstream shift in the upper branch neutral location. Secondary instability computations confirm the previously known dominance of subharmonic modes at relatively small primary amplitudes. However, for the Purdue Mach 6 compression cone configuration, it was shown that a strong fundamental secondary instability can exist for a range of initial amplitudes of the most amplified second mode disturbance, indicating that the exclusive focus on subharmonic modes in the previous applications of secondary instability theory to second mode primary instability may not have been fully justified.

Li, Fei↗

NASA NTRS2022

The NEID Port Adapter at WIYN: On-Sky Fast Guiding Performance

NEID (NN-explore Exoplanet Investigations with Doppler spectroscopy) is an optical, fiber-fed spectrometer installed on the WIYN 3.5m Telescope. The radial velocity precision that NEID is expected to reach requires the stellar jitter (i.e., the slight irregular movement of the stellar image induced by atmospheric turbulence, wind-shake, etc.) to be controlled within 0.05 arc-seconds 90% of the time in nominal observing conditions (i.e., 0.8-arcsecond seeing and mild winds). To achieve that, the NEID Port Adapter incorporates a fast, first-order wavefront correction system, which implements an Electron-Multiplying CCD camera and a tip/tilt piezo stage to capture and stabilize the stellar image. Here, we use on-sky data to demonstrate the performance of this system under various observing conditions.

Dan Li↗

NASA NTRS1982

Experiments on the flow and acoustic properties of a moderate-Reynolds-number supersonic jet

Flow and acoustic properties of a jet at Reynolds number of 70,000 were studied at Mach 2.1. Measurements in a free jet test facility were made with pitot tubes and hot-wire anemometry. Center-line Mach number distributions for natural and excited jets were obtained. A slow initial growth rate was in the potential core region of the jet, indicating a transition from laminar to turbulent flow in moderate Reynolds number jets. The transition occurred within the first 2-3 diameters. Spectral components were calculated for the fluctuating flowfield, and sound pressure levels were measured for the overall near-field noise. The centroid of noise was located about 8 nozzle diameters downstream. The growth rates of instabilities were determined to be in agreement with linear stability theory predictions over a broad frequency range.

Troutt, T. R.↗

NASA NTRS1991

A quiet flow Ludwieg tube for study of transition in compressible boundary layers: Design and feasibility

Laminar-turbulent transition in high speed boundary layers is a complicated problem which is still poorly understood, partly because of experimental ambiguities caused by operating in noisy wind tunnels. The NASA Langley experience with quiet tunnel design has been used to design a quiet flow tunnel which can be constructed less expensively. Fabrication techniques have been investigated, and inviscid, boundary layer, and stability computer codes have been adapted for use in the nozzle design. Construction of such a facility seems feasible, at a reasonable cost. Two facilities have been proposed: a large one, with a quiet flow region large enough to study the end of transition, and a smaller and less expensive one, capable of studying low Reynolds number issues such as receptivity. Funding for either facility remains to be obtained, although key facility elements have been obtained and are being integrated into the existing Purdue supersonic facilities.

Schneider, Steven P.↗

NASA NTRS1992

High speed transition prediction

The main objective of this work period was to develop, acquire and apply state-of-the-art tools for the prediction of transition at high speeds at NASA Ames. Although various stability codes as well as basic state codes were acquired, the development of a new Parabolized Stability Equation (PSE) code was minimal. The time that was initially allocated for development was used on other tasks, in particular for the Leading Edge Suction problem, in acquiring proficiency in various graphics tools, and in applying these tools to evaluate various Navier-Stokes and Euler solutions. The second objective of this work period was to attend the Transition and Turbulence Workshop at NASA Langley in July and August, 1991. A report on the Workshop follows. From July 8, 1991 to August 2, 1991, the author participated in the Transition and Turbulence Workshop at NASA Langley. For purposes of interest here, analysis can be said to consist of solving simplified governing equations by various analytical methods, such as asymptotic methods, or by use of very meager computer resources. From the composition of the various groups at the Workshop, it can be seen that analytical methods are generally more popular in Great Britain than they are in the U.S., possibly due to historical factors and the lack of computer resources. Experimenters at the Workshop were mostly concerned with subsonic flows, and a number of demonstrations were provided, among which were a hot-wire experiment to probe the boundary layer on a rotating disc, a hot-wire rake to map a free shear layer behind a cylinder, and the use of heating strips on a flat plate to control instability waves and consequent transition. A highpoint of the demonstrations was the opportunity to observe the rather noisy 'quiet' supersonic pilot tunnel in operation.

Gasperas, Gediminis↗

NASA NTRS1991

A quiet-flow Ludwieg tube for experimental study of high speed boundary layer transition

Laminar-turbulent transition in high speed boundary layers is a complicated problem which is still poorly understood, partly because of experimental ambiguities caused by operating in noisy wind tunnels. The NASA Langley experience with quiet tunnel design has been used to design a quiet flow tunnel which can be constructed less expensively. Fabrication techniques have been investigated, and inviscid, boundary layer, and stability computer codes have been adapted for use in the nozzle design. Construction of such a facility seems feasible, at a reasonable cost. Two facilities have been proposed: a large one, with a quiet flow region large enough to study the end of transition, and a smaller and less expensive one, capable of studying low Reynolds number issues such as receptivity. Funding for either facility remains to be obtained, although key facility elements have been obtained and are being integrated into the existing Purdue supersonic facilities.

Schneider, Steven P.↗

NASA NTRS1994

Three-Dimensional Navier-Stokes Method with Two-Equation Turbulence Models for Efficient Numerical Simulation of Hypersonic Flows

A new computational efficient 3-D compressible Reynolds-averaged implicit Navier-Stokes method with advanced two equation turbulence models for high speed flows is presented. All convective terms are modeled using an entropy satisfying higher-order Total Variation Diminishing (TVD) scheme based on implicit upwind flux-difference split approximations and arithmetic averaging procedure of primitive variables. This method combines the best features of data management and computational efficiency of space marching procedures with the generality and stability of time dependent Navier-Stokes procedures to solve flows with mixed supersonic and subsonic zones, including streamwise separated flows. Its robust stability derives from a combination of conservative implicit upwind flux-difference splitting with Roe's property U to provide accurate shock capturing capability that non-conservative schemes do not guarantee, alternating symmetric Gauss-Seidel 'method of planes' relaxation procedure coupled with a three-dimensional two-factor diagonal-dominant approximate factorization scheme, TVD flux limiters of higher-order flux differences satisfying realizability, and well-posed characteristic-based implicit boundary-point a'pproximations consistent with the local characteristics domain of dependence. The efficiency of the method is highly increased with Newton Raphson acceleration which allows convergence in essentially one forward sweep for supersonic flows. The method is verified by comparing with experiment and other Navier-Stokes methods. Here, results of adiabatic and cooled flat plate flows, compression corner flow, and 3-D hypersonic shock-wave/turbulent boundary layer interaction flows are presented. The robust 3-D method achieves a better computational efficiency of at least one order of magnitude over the CNS Navier-Stokes code. It provides cost-effective aerodynamic predictions in agreement with experiment, and the capability of predicting complex flow structures in complex geometries with good accuracy.

Bardina, J. E.↗

NASA NTRS1960

The Influence of Low Wall Temperature on Boundary-Layer Transition and Local Heat Transfer on 2-Inch-Diameter Hemispheres at a Mach Number of 4.95 and a Reynolds Number per Foot of 73.2 x 10(exp 6)

Measurements of the location of boundary-layer transition and the local heat transfer have been made on 2-inch-diameter hemispheres in the Langley gas dynamics laboratory at a Mach number of 4.95, a Reynolds number per foot of 73.2 x 10(exp 6), and a stagnation temperature of approximately 400 F. The transient-heating thin-skin calorimeter technique was used, and the initial values of the wall-to-stream stagnation- temperature ratios were 0.16 (cold-model tests) and 0.65 (hot-model test). During two of the four cold tests, the boundary-layer flow changed from turbulent to laminar over large regions of the hemisphere as the model heated. On the basis of a detailed consideration of the magnitude of roughness possibly present during these two cold tests, it appears that this destabilizing effect of low wall temperatures (cooling) was not caused by roughness as a dominant influence. This idea of a decrease in boundary-layer stability with cooling has been previously suggested. (See, for example, NASA Memorandum 10-8-58E.) For the laminar data obtained during the early part of the hot test, the correlation of the local-heating data with laminar theory was excellent.

Cooper, Morton↗