Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Test Pilots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Flight test evaluation and analysis of an optical IR PWI system

The flight test results of the optical infrared (IR) Pilot Warning Instrument (PWI) system are presented. The test program is described and the flight test data presented. The data is analyzed and used to calibrate a model that is developed to characterize the system performance. The cumulative probability of detection versus range from a given system threshold is calculated and compared with the PWI performance specification. The comparison indicates that the Optical IR PWI system tested met the specifications for a detection likelihood of 95 percent for a 1 nmi range for an appreciable fraction of the testing time.

Phillips, C. O.↗
NASA NTRS1986

Evaluation of a storable fluorine based pilot for scramjets

An ignitor/pilot device for scramjet engines has been tested with C2H4, C2H6, and CH4 gaseous hydrocarbon fuels at Mach 2. The pilot was designed to operate with storable nontoxic propellants rather than hazardous pyrophorics; the pilot fluid is a mixture of ethylene, oxygen, and sulfur hexafluoride. The pilot reduced the minimum temperature at which all three hydrocarbon fuels ignited; a comparison was then conducted between combustion efficiency calculations for these test results and those of pilots using nitrogen in place of sulfur hexafluoride, and using silane-hydrogen (yielding equivalent energy). The nitrogen-substituted pilot exhibited the highest efficiency.

Diskin, G. S.↗
NASA NTRS1992

Flight deck benefits of integrated data link communication

A fixed-base, piloted simulation study was conducted to determine the operational benefits that result when air traffic control (ATC) instructions are transmitted to the deck of a transport aircraft over a digital data link. The ATC instructions include altitude, airspeed, heading, radio frequency, and route assignment data. The interface between the flight deck and the data link was integrated with other subsystems of the airplane to facilitate data management. Data from the ATC instructions were distributed to the flight guidance and control system, the navigation system, and an automatically tuned communication radio. The co-pilot initiated the automation-assisted data distribution process. Digital communications and automated data distribution were compared with conventional voice radio communication and manual input of data into other subsystems of the simulated aircraft. Less time was required in the combined communication and data management process when data link ATC communication was integrated with the other subsystems. The test subjects, commercial airline pilots, provided favorable evaluations of both the digital communication and data management processes.

Waller, Marvin C.↗
NASA NTRS1999

Exercise Training During +Gz Acceleration

The overall purpose is to study the effect of passive (without exercise) and active (with exercise) +Gz (head-to-foot) acceleration training, using a short-arm (1.9m radius) centrifuge, on post- training maximal oxygen uptake (VO2 max, work capacity) and 70 deg head-up tilt (orthostatic) tolerance in ambulatory subjects to test the hypothesis that (a) both passive and active acceleration training will improve post-training tilt-tolerance, and (b) there will be no difference in tilt-tolerance between passive and active exercise acceleration training because increased hydrostatic and blood pressures, rather than increased muscular metabolism, will provide the major adaptive stimulus. The purpose of the pilot study was to test the hypothesis that there would be no significant difference in the metabolic responses (oxygen uptake, heart rate, pulmonary ventilation, or respiratory exchange ratio) during supine exercise with moderate +Gz acceleration.

Greenleaf, J. E.↗
DOE OSTI2021

UKy-CAER Heat Integrated Transformative CO 2 Capture Process in Pulverized Coal Power Plants

The goal of this Phase II Topical Report is to summarize the work for public domain conducted on project DE-FE0031583. Building upon the Design Basis completed during Phase I and in accordance with the Statement of Project Objectives (SOPO), the University of Kentucky (UK) Center for Applied Energy Research (CAER) (Recipient) along with team members has completed the Front End Engineering Design (FEED) for its advanced, versatile post-combustion CO 2 capture system (CCS) at the 10 MWe large pilot scale to be installed at the Wyoming (WY) Integrated Test Center (ITC), using a heat integrated process with split-rich fed, two-stage stripping and any advanced solvent to enhance the CO 2 absorber performance and lower the cost of CO 2 capture. The proposed project (Phases I-III) involves the design, fabrication, installation, testing and evaluation of a large pilot scale facility that will demonstrate the UK CAER transformative CCS integrated with an operating power plant. The work performed in Phase I, detailed in the Phase I Topical Report that was submitted in March 2019, included formation of a project team, securing the host site, and completing pre-FEED design basis, a cost estimation, a preliminary techno-economic analysis (TEA) and an environmental information volume (EIV). The work performed in Phase II, detailed in this Phase II Topical Report, includes completion of FEEDs, completion of a process risk analysis (PRA), obtaining necessary permits, updating the EIV and TEA, updating the cost and schedule estimate for the Phase III scope of work (SOW) and securing the necessary cost share. Updated information is provided on the current status of the UK CAER CCS technology and the project is ready to begin immediately detailed design, construction and operation of the proposed pilot.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1980

Flight test experience using advanced airborne equipment in a time-based metered traffic environment

A series of test flights have demonstrated that time-based metering guidance and control was acceptable to pilots and air traffic controllers. The descent algorithm of the technique, with good representation of aircraft performance and wind modeling, yielded arrival time accuracy within 12 sec. It is expected that this will represent significant fuel savings (1) through a reduction of the time error dispersions at the metering fix for the entire fleet, and (2) for individual aircraft as well, through the presentation of guidance for a fuel-efficient descent. Air traffic controller workloads were also reduced, in keeping with the reduction of required communications resulting from the transfer of navigation responsibilities to pilots. A second series of test flights demonstrated that an existing flight management system could be modified to operate in the new mode.

Morello, S. A.↗
NASA NTRS1973

Visual-motor response of crewmen during a simulated 90-day space mission as measured by the critical task battery

In order to test various components of a regenerative life support system and to obtain data on the physiological and psychological effects of long duration exposure to confinement in a space station atmosphere, four carefully screened young men were sealed in a space station simulator for 90 days and administered a tracking test battery. The battery included a clinical test (Critical Instability Task) designed to measure a subject's dynamic time delay, and a more conventional steady tracking task, during which dynamic response (describing functions) and performance measures were obtained. Good correlation was noted between the clinical critical instability scores and more detailed tracking parameters such as dynamic time delay and gain-crossover frequency. The levels of each parameter span the range observed with professional pilots and astronaut candidates tested previously. The chamber environment caused no significant decrement on the average crewman's dynamic response behavior, and the subjects continued to improve slightly in their tracking skills during the 90-day confinement period.

Allen, R. W.↗
NASA NTRS2020

Flight Simulation Scenarios for Commercial Pilot Training and Crew State Monitoring

NASA Langley researchers addressed the Commercial Aviation Safety Team Safety Enhancement 211 through a series of studies to address "Attention-related Human Performance Limiting States" which include channelized attention, diverted attention, startle/surprise, and confirmation bias. The present report focuses on the development of improved training scenarios for operationally realistic Line-Oriented Flight Training scenarios. Areas addressed in the report include: (1) Highlights of events in the LOFT scenario used; (2) Interesting findings with implications for simulator motion; (3) Eye-tracking heat maps in proximity to failure events; (4) Researcher observations of crews as test subjects versus a pilot and a research team co-pilot; and (5) The results of a follow-up questionnaire completed by pilot participants regarding their usual training as well as the scenarios employed in the SHARP studies. These pilot ratings and comments are of value to simulation training developers.

James R. Comstock, Jr.↗
NASA NTRS1995

Parameter identification and modeling of longitudinal aerodynamics

Using a comprehensive flight test database and a parameter identification software program produced at NASA Ames Research Center, a math model of the longitudinal aerodynamics of the Harrier aircraft was formulated. The identification program employed the equation error method using multiple linear regression to estimate the nonlinear parameters. The formulated math model structure adhered closely to aerodynamic and stability/control theory, particularly with regard to compressibility and dynamic manoeuvring. Validation was accomplished by using a three degree-of-freedom nonlinear flight simulator with pilot inputs from flight test data. The simulation models agreed quite well with the measured states. It is important to note that the flight test data used for the validation of the model was not used in the model identification.

Aksteter, J. W.↗
NASA NTRS1990

Effect on real-world depth perception from exposure to heads-down stereoscopic flight displays

A stereoacuity test was used as part of the experimental protocol of a study in which eight transport pilots flew repeated simulated landing approaches using both stereo and nonstereo three-dimensional heads-down 'pathway in the sky' displays. At the decisionmaking crux of each approach, the pilots transitioned to a stereoacuity test employing real objects rather than a two-dimensional target apparatus. A statistical analysis of stereoacuity measures which compared a controlled condition of no exposure to any electronic flight display with the transition data from nonstereo and stereopsis displays indicated no significant differences for any of the conditions.

Busquets, Anthony M.↗
NASA NTRSDate not supplied

Real-Time Pilot Inputs for Aircraft Dynamic Modeling

Real-time dynamic modeling and pilot displays are used to enable pilots to intuitively discover effective multi-axis inputs for aircraft dynamic modeling during flight tests. An F-16 nonlinear simulation flown by a pilot using a joystick and a laptop computer with real-time displays of relevant information is used to demonstrate the approach. Results show that pilots can use the real-time display to discover and implement effective and efficient multi-axis inputs for accurate dynamic modeling in flight. The real-time dynamic modeling results driving the pilot display can be used to certify that the acquired flight data are adequate for accurate dynamic modeling, thus avoiding postflight data analysis and modeling by an analyst to make that determination. Implications for pilot training and efficient flight testing are discussed.

Pilot Inputs↗
DOE OSTI2023

Analysis of Deformation and Fracture Mechanisms in the Harvested Low-Dose Baffle Former Bolt via Advanced Mechanical Tests

This report details the production of tensile specimens from in-service irradiated baffle former bolts (BFBs) and presents the results of a pilot in-situ SEM/EBSD test conducted at Oak Ridge National Laboratory’s Low Activation Materials Development and Analysis (LAMDA) facility. The SEM/EDS results confirmed that the material is AISI 316L steel, not AISI 347, and that no Nb addition was detected in several analyzed locations. EBSD analysis of the microstructure revealed in-grain misorientation gradients indicative of cold work, likely caused by material processing, and no retained ferrite was identified. During straining, dislocation channel formation was the primary deformation mechanism, with twinning also observed in favorably oriented grains at local strains as small as ~1.5%. No strain-induced phase instability was observed, likely due to the fact that the Ni and Cr content reached the upper limits for the 316L steel specification. Multiple microfracture events were observed during the tensile test. Fine strain-induced pores formed at the channel-grain boundary intersection points, while coarser microcracks were associated with non-metallic inclusions. Data analysis is ongoing, and additional tests are planned in the near future to provide more statistics and details.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Multi-Agency Annual Southeastern Beach Mouse Habitat Occupancy Monitoring

The southeastern beach mouse (Peromyscus polionotus niveiventris, hereafter SEBM), a federally threatened species was identified by Merritt Island National Wildlife Refuge (MINWR) as one of the top five priorities for management. The Kennedy Space Center (KSC) Environmental Management Branch was asked to provide support in the form of population monitoring for SEBM on KSC and the surrounding properties. When we began the project, the SEBM was known to occupy sites ranging from Volusia through Brevard and Indian River Counties, but the exact distribution within the Federal lands encompassing the Cape Canaveral Barrier Island Complex (CCBIC) was not well known. The broad range of habitat conditions encompassing the species’ historical range and the diversity of sites historically known to contain SEBM required a landscape-scale approach for both monitoring the population and for investigating species habitat relationships. We designed a monitoring plan for the SEBM with the goal of estimating the habitat occupancy of beach mice annually each winter/spring throughout the entire area of suitable coastal habitat (approximately 72 km linear distance along the beach). Methods were tested in a 2008 pilot study, and during 2010-2018 we monitored the proportion of coastal habitat occupied by the SEBM on the CCBIC. Monitoring was focused on using dynamic habitat occupancy surveys with data collected with rapid assessment techniques (i.e., track tubes or live-traps) to detect SEBM occurrence at sampling stations. An important component of the study design was the use of repeated samples that provided the information needed to estimate detectability. Measuring detectability was required to account for the fact that surveys could fail to detect animals at sites at which they were actually present (Mackenzie et al., 2002). This monitoring framework is very flexible, allowing numerous hypothesis to be tested about how various factors influence beach mouse occupancy using habitat, geographic, and environmental covariates. Our survey has been the longest survey conducted for any of the seven extant beach mouse subspecies and has encompassed nearly the entire remaining range of the SEBM. Although occupancy surveys of other beach mouse subspecies via track tubes have been conducted on the Gulf coast of Florida by Florida Fish and Wildlife Conservation Commission (FWC), United States Fish and Wildlife Service (USFWS), and various universities, we expanded previous methods to fit unique aspects of the SEBM, and thus our study was very different from any of the previous studies. To achieve this specificity, we employed an adaptive approach throughout the study, with all activities aimed at providing managers with information related to environmental compliance and natural resource management on KSC and the surrounding Federal lands.

Eric Douglas Stolen↗
NASA NTRS1994

Initial Field Evaluation of Pilot Procedures for Flying CTAS Descent Clearances

The Center TRACON Automation System (CTAS) is a new support system that is designed to assist air traffic controllers in the management of arrival traffic. CTAS will provide controllers with more information about current air traffic, enabling them to provide clearances for efficient, conflict-free descents that help achieve an orderly stream of aircraft at the final approach fix. CTAS is a computer-based system that functions as a "ground-based FMS" that can predict flight trajectories and arrival times for all incoming aircraft. CTAS uses an aircraft's cruise airspeed; current air traffic, winds and temperature; performance characteristics of the aircraft type; and individual airline preferences to create a flight profile from cruise altitude to the final approach fix. Controllers can use this flight profile to provide a descent clearance that will allow an aircraft to fly an efficient descent and merge more smoothly with other arriving aircraft. A field test of the CTAS Descent Advisor software was conducted at the Denver Center for aircraft arriving at the Stapleton International Airport from September 12-29. CTAS Descent clearances were given to a NASA flight test aircraft and to 77 airline flights that arrived during low traffic periods. For the airline portion of the field test, cockpit procedures and pilot briefing packages for both FMS equipped and unequipped aircraft were developed in cooperation with an airline. The procedures developed for the FMS equipped aircraft were to fly a VNAV descent at a controller specified speed to cross a metering fix at a specified altitude and speed. For nonFMS aircraft, the clearance also specified a CTAS calculated top-of-descent point. Some CTAS related flight deck issues included how much time was available to the pilots' for compliance, the amount of information that needed to be interpreted in the clearance and possible repercussions of misunderstandings. Data collected during the study ranged from subjective data (including the airline pilots' opinions and comments about the new descent clearances and procedures) to objective data (including observations of aircraft performance from the flight deck). This paper will present data and the resulting changes in the design of the procedures and clearance phraseology.

Palmer, Everett↗
NASA NTRS1979

Lean stability augmentation for premixing, prevaporizing combustors

An experimental program was conducted to investigate techniques for improving the lean combustion limits of premixing, prevaporizing combustors applicable to gas turbine engine main burners. Augmented flameholders employing recessed perforated plates, catalyzed tube bundles, and configurations in which pilot fuel was injected into the wakes of V-gutters or perforated plates were designed and tested. Stable operation of the piloted designs was achieved at equivalence ratios as low as 0.25; NOx emissions of less than 1.0 g/kg at simulated turbine engine cruise conditions were obtained. A piloted perforated plate employing four percent pilot fuel flow produced the best performance while meeting severe NOx constraints.

Mcvey, J. B.↗
NASA NTRSDate not supplied

Command and Control Concepts for an Lift Plus Cruise Electric Vertical Takeoff and Landing Vehicle

Electric Vertical Takeoff and Landing (eVTOL) vehicles have the potential to enable cost effective Urban Air Mobility (UAM) applications. Many of these vehicle concepts will takeoff vertically like a helicopter, transition to fly like an airplane, and then transition back to land vertically like a helicopter. However, these concepts may also pose several challenging handling and control problems, which must be addressed prior to safe and reliable urban operations. This study investigates some of these challenges by evaluating different command and control concepts for a conceptual Lift Plus Cruise vehicle designed by NASA’s Revolutionary Vertical Lift Technology (RVLT) project. Four different command concepts with increasing levels of automation are developed. The command and control architecture for these concepts is presented along with findings from the evaluation of these concepts in a series of three piloted studies in the Vertical Motion Simulator at NASA Ames Research Center, where pilots flew operationally relevant flight test maneuvers specifically designed to expose potential deficiencies. The higher-level control systems and the associated pilot interfaces were shown to improve performance and handling in many cases, especially for higher precision and lower to moderate aggression maneuvers. The benefits were limited for higher aggression tasks in environmentally stressing conditions, due to the slower response of the automation and inherent limitations of the vehicle design, which highlights the potential need for tradeoffs between concept of operations and vehicle capabilities

Thomas Lombaerts↗
NASA NTRS2017

Mild Normobaric Hypoxia Exposure for Human-Autonomy System Testing

An experiment investigated the impact of normobaric hypoxia induction on aircraft pilot performance to specifically evaluate the use of hypoxia as a method to induce mild cognitive impairment to explore human-autonomous systems integration opportunities. Results of this exploratory study show that the effect of 15,000 feet simulated altitude did not induce cognitive deficits as indicated by performance on written, computer-based, or simulated flight tasks. However, the subjective data demonstrated increased effort by the human test subject pilots to maintain equivalent performance in a flight simulation task. This study represents current research intended to add to the current knowledge of performance decrement and pilot workload assessment to improve automation support and increase aviation safety.

Stephens, Chad L.↗
NASA NTRS2005

Advanced Weather Awareness and Reporting Enhancements

AWARE (Aviation Weather Awareness and Reporting Enhancements) was a NASA Cooperative Research and Development program conducted jointly by Rockwell Scientific, Rockwell Collins, and NASA. The effort culminated in an enhanced weather briefing and reporting tool prototype designed to integrate graphical and text-based aviation weather data to provide clear situational awareness in the context of a specific pilot, flight and equipment profile. The initial implementation of AWARE was as a web-based preflight planning tool, specifically for general aviation pilots, who do not have access to support such as the dispatchers available for commercial airlines. Initial usability tests showed that for VFR (Visual Flight Rules) pilots, AWARE provided faster and more effective weather evaluation. In a subsequent formal usability test for IFR (Instrument Flight Rules) pilots, all users finished the AWARE tests faster than the parallel DUAT tests, and all subjects graded AWARE higher for effectiveness, efficiency, and usability. The decision analysis basis of AWARE differentiates it from other aviation safety programs, providing analysis of context-sensitive data in a personalized graphical format to aid pilots/dispatchers in their complex flight requirements.

Busquets, Anthony M.↗