Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

A Physical Model to Study the Effects of Nozzle Design on Dispersed Two-Phase Flows in a Slab Mold Casting Ultra-Low-Carbon Steels

The effects of nozzle design on dispersed, two-phase flows of the steel-argon system in a slab mold are studied using a water-air model with particle image velocimetry and ultrasound probe velocimetry techniques. Three nozzle designs were tested with the same bore size and different port geometries, including square (S), special bottom design with square ports (U), and circular (C). The meniscus velocities of the liquid increase two- or threefold in two-phase flows regarding one-phase flows using low flow rates of the gas phase. This effect is due to the dragging effects on bubbles by the liquid jets forming two-way coupled flows. Liquid velocities (primary phase) along the narrow face of the mold also are higher for two-phase flows. Flows using nozzle U are less dependent on the effects of the secondary phase (air). The smallest bubble sizes are obtained using nozzle U, which confirms that bubble breakup is dependent on the strain rates of the fluid and dissipation of kinetic energy in the nozzle bottom and port edges. Through dimensionless analysis, it was found that the bubble sizes are inversely proportional to the dissipation rate of the turbulent kinetic energy, ε{sup 0.4}. A simple expression involving ε, surface tension, and density of metal is derived to scale up bubble sizes in water to bubble sizes in steel with different degrees of deoxidation. The validity of water-air models to study steel-argon flows is discussed. Prior works related with experiments to model argon bubbling in steel slab molds under nonwetting conditions are critically reviewed.

36 MATERIALS SCIENCE↗

Reaction Behaviors of Al-Killed Medium-Manganese Steel with Different Refractories

In order to understand the reaction mechanism between medium-manganese steel and different refractories, some laboratory experiments were carried out at 1873 K (1600 °C). Three types of refractory plates (Al{sub 2}O{sub 3}, MgO, and MgO·Al{sub 2}O{sub 3}) were used. The results show that Mn in liquid medium-manganese steel does not react easily with the Al{sub 2}O{sub 3} refractory, but can react with the MgO refractory to generate a (Mn, Mg)O layer at the boundary between the refractory plate and liquid steel. After the formation of (Mn, Mg)O, a layer of (Mn, Mg)O·Al{sub 2}O{sub 3} spinel is also formed at the edge of the MgO refractory. Similar to the MgO refractory, the dissolved Mn can react with the MgO·Al{sub 2}O{sub 3} refractory as well, and a layer of (Mn, Mg)O·Al{sub 2}O{sub 3} was also detected after reaction. It was found that the formation of (Mn, Mg)O·Al{sub 2}O{sub 3} at the edge of the refractory is a source of (Mn, Mg)O·Al{sub 2}O{sub 3} inclusions in liquid steel. The flush-off of the (Mn, Mg)O·Al{sub 2}O{sub 3} layer would result in the formation of (Mn, Mg)O·Al{sub 2}O{sub 3} inclusions.

36 MATERIALS SCIENCE↗

Transient Evolution of Nonmetallic Inclusions During Calcium Treatment of Molten Steel

The transient evolution of nonmetallic inclusions after calcium addition in pipeline steels was investigated with a vacuum induction furnace. Samples were taken at 1, 5, 10, 15, and 20 minutes after calcium treatment in both MgO and Al{sub 2}O{sub 3} crucibles. It was found that the total oxygen and the number density of inclusions were increased during calcium modification, while they were dropped to a low level in the last tapped sample. Due to the evaporation of calcium, inclusions were transferred from CaO-CaS to Al{sub 2}O{sub 3}-CaO-CaS, and then to Al{sub 2}O{sub 3}-CaO. The decomposition of CaS was highly dependent on the decrease of the total calcium and the increase of the total oxygen in the steel. Thermodynamic calculation was performed to predict the composition of inclusions considering the effect of the total oxygen and the total calcium and was validated by measurement. The relationship between the content of Al{sub 2}O{sub 3} in inclusions and the ratio of the total calcium and the total oxygen in steels was measured and compared with the calculated one using thermodynamic software Factsage 7.0. The mass-transfer coefficient of the dissolved calcium in the steel was estimated in the range of 2.35 × 10{sup −4} to 3.53 × 10{sup −4} m/s.

36 MATERIALS SCIENCE↗

Characterization of X80 and X100 Microalloyed Pipeline Steel Using Quantitative X-ray Diffraction

Quantitative X-ray diffraction characterization of four (4) X80 and three (3) X100 microalloyed steels was undertaken. The effect of through-thickness position, processing parameters, and composition on the measured crystallite size, microstrain, and J index (relative magnitude of crystallographic texture) was determined. Microstructure analysis using optical microscopy, scanning electron microscopy, transmission electron microscopy, and electron-backscattered diffraction was also undertaken. The measured value of microstrain increased with increasing alloy content and decreasing cooling interrupt temperature. Microstructural features corresponding to crystallite size in the X80 steels were both above and below the detection limit for quantitative X-ray diffraction. The X100 steels consistently exhibited microstructure features below the crystallite size detection limit. The yield stress of each steel increased with increasing microstrain. The increase in microstrain from X80 to X100 is also associated with a change in microstructure from predominantly polygonal ferrite to bainitic ferrite.

36 MATERIALS SCIENCE↗

Research on Selective Oxidation of Carbon and Aluminum with Introduction of CO{sub 2} in RH Refining of Low-Carbon Steel Process

The injection of CO{sub 2} during the Rheinstahl–Heraeus (RH) refining process as a lifting gas is a new attempt for the steel industry, and can promote refining effect and realize the utilization of CO{sub 2} as a resource. In the present study, the thermodynamic equilibrium of the RH refining process through CO{sub 2} injection instead of Ar was calculated using FactSage software. A selective oxidation sequence of [C] and [Al] with CO{sub 2} was studied and analyzed under the RH refining temperature and vacuum degree. In addition, the oxidation zones of carbon and aluminum were both defined. Industrial trials were preliminarily conducted to verify the above theory. The results show that CO{sub 2} has the potential to be used to refine low-carbon steel in RH, but its refining effect is affected by the [Al] content in steel. By reducing the additive amount of aluminum alloy in the ladle furnace and replenishing the aluminum during the late stage of the RH refining process, CO{sub 2} injection can achieve a lower temperature drop of molten steel and a better refining effect than Ar during the RH degassing process.

36 MATERIALS SCIENCE↗

Effect of Nozzle Port Angle on Transient Flow and Surface Slag Behavior During Continuous Steel-Slab Casting

Undesirable flow variations can cause severe instabilities at the interface between liquid mold flux and molten steel across the mold top-region during continuous steel casting, resulting in surface defects in the final products. A three-dimensional Large Eddy Simulation (LES) model using the volume of fluid method for the slag and molten steel phases is validated with plant measurements, and applied to gain new insights into the effects of nozzle port angle on transient flow, top slag/steel interface movement, and slag behavior during continuous slab casting under nominally steady conditions. Upward-angled ports produce a single-roll flow pattern with lower surface velocity, due to rapid momentum dissipation of the spreading jet. However, strong jet wobbling from the port leads to greater interface variations. Severe level drops allow easy entrapment of liquid flux by the solidifying steel shell at the meniscus. Sudden level rises may also be detrimental, leading to overflow of the solidified meniscus region. Downward-angled ports produce a classic double-roll pattern with less jet turbulence and a more stable interface everywhere except near the narrow faces. Finally, the flow patterns, surface velocity, and level predicted from the validated LES model are compared with steady-state standard k-ε model predictions.

36 MATERIALS SCIENCE↗

Evolution Mechanism of Inclusions in Medium-Manganese Steel by Mg Treatment with Different Aluminum Contents

To investigate the effect of magnesium addition on the evolution of inclusions in medium-manganese steel with different aluminum contents, both thermodynamic calculation and high-temperature simulation experiments were carried out in the present work. The in situ observation experiments were used to clarify the related evolution process of inclusions. The samples taken from the melts were analyzed by scanning electron microscopy and energy dispersive spectroscopy. The compositions of steel were determined by inductively coupled plasma-optical emission spectrometer. The results show that the aluminum content in steel has a certain influence on the magnesium content, under the same conditions, magnesium content increases with increasing aluminum content. The inclusions transformed from MnO·Al{sub 2}O{sub 3} to Al{sub 2}O{sub 3} when the aluminum content was higher than 0.0076 mass pct. After magnesium treatment, the inclusions gradually transformed into MgO·Al{sub 2}O{sub 3}, and the MgO/Al{sub 2}O{sub 3} mole ratio in inclusions decreased with the increase of aluminum content. The diameter of the inclusions decreased, and number density of inclusions increased in steel after magnesium addition. The phenomenon that large-sized cluster-like Al{sub 2}O{sub 3} inclusions transform into finely dispersed Mg-containing inclusions was firstly observed in situ by confocal laser scanning microscope.

36 MATERIALS SCIENCE↗

Analysis of Hot- and Cold-Rolled Loads in Medium-Mn TRIP Steels

The purpose of this work is to investigate the hot- and cold-rolling requirements to produce third-generation advanced high-strength steels (AHSS). Therefore, five medium-Mn (10 to 14 wt pct Mn) alloys that exhibit transformation-induced plasticity (TRIP) were compared to a commercially produced grade of AISI 1018 using hot- and cold-rolling experiments. Experimental data collected from a STANAT instrumented rolling mill was utilized to measure force and torque during hot- and cold-rolling. Experimental data were processed by a 1D analytical model, based on Orowan model, to determine rolling pressure. It was determined that pressures required to hot-roll TRIP alloys are 1.4 to 1.8 times greater than pressures for rolling AISI 1018 steel. Cold rolling of the medium-Mn TRIP steels was found to be 1.5 to 2.8 times greater than the AISI 1018 steel. Mechanical and microstructural characterization was also performed and the variation in rolling pressure was related to the starting microstructural constituents, and alloys containing greater starting quantities of ε-martensite in the microstructure had higher flow stresses at equivalent rolling strains during cold rolling.

36 MATERIALS SCIENCE↗

Precipitation Mechanism and Reduction of Amount of Primary Carbides During Electroslag Remelting of 8Cr13MoV Stainless Steel

The precipitation and growth of primary carbides in 8Cr13MoV steel during electroslag remelting (ESR) were studied. The effects of melting rate and fill ratio of ESR on the reduction of primary carbides were clarified. Primary carbides M{sub 7}C{sub 3} precipitated from liquid steel at the final stage of solidification, which is attributed to an enrichment of carbon and chromium in liquid steel. The carbon content in the residual liquid steel was the determining factor for the formation of primary carbides. The growth of primary carbides was affected mainly by the chromium-concentration and temperature-field gradients. An appropriate melting rate facilitated the nucleation and growth of dendrites, which caused dendrite closure and prevented the further enrichment of carbon atoms. Primary carbides were refined and their amount was reduced when using a lower ESR melting rate. The fill ratio can affect the uniformity of the temperature field in the liquid metal pool and heat transfer from the slag pool to the liquid metal pool, and an optimal fill ratio resulted in a minimum mushy zone and less primary carbides. The volume fraction of primary carbides was reduced by 23 pct when the melting rate decreased from 150 to 133 kg/h and the fill ratio increased from 0.23 to 0.33.

36 MATERIALS SCIENCE↗

Quantitative Evaluations of Surface Cleanliness in IF Steel Slabs at Unsteady Casting

Macro-inclusions in the surface layer of slabs are mainly responsible for the sliver defects in IF steel sheets. In the present work, macro-inclusions in six kinds of unsteady cast IF steel slabs involving four unsteady states (casting start, ladle change, nozzle change and casting end) in one casting sequence were quantitatively characterized using an automatic inclusion analyzer with a total detection area of 238,048 mm{sup 2}. The cleanliness of corresponding normal slabs was also evaluated as the benchmark study, and the number density (ND) of inclusions > 50 µm was used to describe the surface slab cleanliness. Generally, alumina-based and mold powder inclusions were detected, and the former type was further subdivided into alumina clusters, alumina associated with bubbles, refractory-related alumina, Al-Ti complex oxides and CaO-Al{sub 2}O{sub 3}-MgO. Several large-sized alumina-based inclusions were detected in the normal slabs with an average ND of 0.31 N/cm{sup 2}, although they had very low total oxygen (TO) contents (10~13 ppm). No mold powder inclusions were found in normal slabs. For all the unsteady slabs, alumina-based and mold powder inclusions were both observed, and the percentage of the former kind was ≥ 90 pct. The average density of macro-inclusions for the first slab was 1.621 N/cm{sup 2}, whose cleanliness was much worse than any of the other unsteady slabs. The first slab should be downgraded. For the second slab, the ND of macro-inclusions was 0.385 N/cm{sup 2}, which was still larger than the normal slabs because of the lasting effect of the re-oxidation. For the penultimate, cap-off and SEN changed slabs, the density of macro-inclusions fluctuated from 0.25~0.35 N/cm{sup 2}, which was close to the average level of normal slabs. However, mold flux-originated inclusions were frequently observed in these slabs because of flow pattern variations due to the casting speed change. In terms of the slab during the ladle change process, mold powder inclusions were frequently detected even though the casting speed remained constant. A mold powder entrapment mechanism was proposed, which showed the entrapment occurred owing to the flow pattern change induced by forming/dropping of SEN clogs due to re-oxidation by FeO in the ladle slag and tundish steel temperature variations during the ladle change practice. The severity of powder entrapment and re-oxidation was also given for different kinds of unsteady slabs, which provides a direct guide to treating these slabs in the steel plant.

36 MATERIALS SCIENCE↗

Solidification and Liquation Cracking Behavior of Dual-Phase Steel DP600

In this work, the solidification and liquation cracking behavior of a dual-phase steel DP600 was examined using longitudinal Varestraint testing and hot ductility testing. Varestraint tests showed only limited cracking even at 4 pct augmented strain. Hot ductility tests showed that the nil-strength temperature of the steel was 1459 °C, while the nil-ductility and the ductility-recovery temperatures were 1435 °C and 1420 °C, respectively. The brittleness temperature range was found to be 39 °C, and the DP600 steel was highly resistant to both weld metal solidification cracking and heat-affected zone liquation cracking. The reasons for the high hot cracking resistance of dual-phase steel DP600 are discussed.

36 MATERIALS SCIENCE↗

Effect of Tempering Temperature on the Microstructure and Properties of Fe-2Cr-Mo-0.12C Pressure Vessel Steel

To obtain the high-temperature strength and toughness of the medium–high-temperature–pressure steel, the microstructure evolution and mechanical properties of Fe-2Cr-Mo-0.12C steel subjected to three different tempering temperatures after being normalized were investigated. The results show that the microstructure of the sample, tempered in the range 675-725 °C for 50 min, did not change dramatically, yet the martensite/austenite constituents decomposed, and the bainite lath merged together and transformed into polygonal ferrite. At the same time, the precipitate size increased with an increase in tempering temperature. With the increase in the tempering temperature from 675 to 725 °C, the impact absorbed energy of the Fe-2Cr-Mo-0.12C steel at −40 °C increased from 257 to 325 J, and the high-temperature yield strength decreased; however, the high-temperature ultimate tensile strength tempered at 700 °C was outstanding (422-571 MPa) at different tested temperatures. The variations of the properties were attributed to the decomposition of M/A constituents and the coarsening of the precipitates. Fe-2Cr-Mo-0.12C steel normalized at 930 °C and tempered at 700 °C was found to have the best combination of ductility and strength.

36 MATERIALS SCIENCE↗

Effects of Roughing on Finish Rolling Simulations in Microalloyed Strip Steels

The effects of a roughing pass in hot rolling simulations were assessed in VN and Nb-Ti steels. Continuous cooling phase transformation temperatures, flow curves, softening mechanisms (dynamic transformation DT and dynamic recrystallization DRX), and deformed microstructure morphologies were analyzed. The application of one or more roughing passes eliminates the effects of prior microstructural history and ensures that all stock material experiences equivalent hot working conditions and state of the microalloying elements. It has been shown that roughing in hot simulation has the following positive influences: (1) provide more reliable flow stress data; (2) give greater consistencies and accuracy in analysis of softening mechanisms giving three distinct regimes (DT regime at temperatures below 800 °C, DT/DRX inter-mode regime between 800 and 950 °C and DRX regime for temperatures above 950 °C for VN steel); (3) promotion of softening mechanisms as evidence by low critical strains (ε{sub c DT} was within the range 0.08-0.12, while for finishing-only pass, the ε{sub c DT} was in the range of 0.11-0.14 at ε-dot =0.1 s{sup −1}); (4) for roughing and finishing schedules, DT was verified to occur at temperatures 117 and 133 °C above Ae{sub 3} for VN steel and Nb-Ti steel, respectively, compared to the F-only schedules which showed that DT can only occur at temperatures below the Ae{sub 3}; (5) RF schedules promoted uniform microstructural morphologies compared to inhomogeneous microstructures realized in F-only schedules.

36 MATERIALS SCIENCE↗

Study on Static Recrystallization Behavior of Medium-Carbon Cr-Ni-Mo Alloyed Steel During Hot Deformation

A series of two-pass hot compression tests were conducted on Gleeble-1500 thermo-mechanical simulator to investigate the static recrystallization (SRX) behavior of a medium-carbon Cr-Ni-Mo alloyed steel 34CrNiMo. The compression tests were performed at a deformation temperature range of 950-1150 °C, a strain rate range of 0.1-3.5 s{sup −1}, and an interval time range of 1-100 s. The experimental flow stress curves and microstructural observation indicate that deformation temperature, pass interval time, strain rate, and pre-strain have significant influences on the recrystallization behavior of 34CrNiMo steel. It is identified that the softening fraction increases with the increasing deformation temperature, pre-strain, and interval time, while it decreases with the increasing strain rate. Based on the experimental data, the SRX kinetics equations of 34CrNiMo steel were developed. And the calculated results are in good agreement with the experimental ones, which demonstrates that the established equations can be used to describe the SRX behavior of 34CrNiMo steel at elevated temperatures.

36 MATERIALS SCIENCE↗

Very Hard Corrosion-Resistant Roll-Bonded Cr Coating on Mild Steel in Presence of Graphite

The present work discusses the development of very hard Cr and Cr-carbide coating by roll bonding of Cr powder on a mild steel followed by annealing at 800, 1000, 1100 and 1200 °C with and without the presence of graphite powder packing in argon environment. In addition, the effect of a roll skin pass of 5% prior to the application of coating was studied. The presence of graphite allows diffusion of both carbon and Cr in the mild steel substrate, leading to the formation of Cr-carbide on the outer surface, making the surface very hard (VHN ~ 1800). Depending on the annealing temperature and processing condition, diffusion layer thickness of Cr is found to be in the range of 10-250 μm with Cr content of 12.5-15 wt.% across the diffusion layer. Excellent stable passivity of the coated surface is observed in 0.2 N H{sub 2}SO{sub 4}, which is comparable to a highly passivating 304 stainless steel, and very low corrosion rate of the coating is observed as compared to the substrate mild steel.

36 MATERIALS SCIENCE↗

Effect of Pulse Detonation-Plasma Technology Treatment on T8 Steel Microstructures

T8 steel surfaces were treated by pulse detonation-plasma technology (PDT) at capacitance values of 600, 800, and 1000 μF, and the effects of PDT were analyzed using x-ray diffraction, scanning electron microscopy, transmission electron microscopy, electron back-scattered diffraction, and micro-hardness tester and friction wear tester. The surface of T8 steel is first smoothed out, and then, craters are formed due to the inhomogeneity of the PDT energy and targeting during PDT treatment. The initial martensite in the T8 steel surface layer changes to austenite, and Fe{sub 3}N is formed due to nitriding. The thickness of the modified layer, which is composed of columnar and fine grain structures, increases with the increasing capacity. Preferential orientation occurred in the {110} 〈 001 〉 direction in the modified layer, and the number of low-angle grain boundaries increased significantly after PDT treatment. The micro-hardness and wear resistance of the T8 steel was improved by PDT treatment, even doubled after the treatment with the capacitance of 1000 μF.

36 MATERIALS SCIENCE↗

Heavy Deformation of Patented Near-Eutectoid Steel

Evolution of microstructure in the patented near-eutectoid steel, forged under varying situations, is critically examined in the present investigation. Steel with 0.74 wt.% carbon is isothermally annealed at 500 °C to obtain fine pearlite microstructure. Steel samples, so patented, are subjected to mechanical deformation by forging at various temperatures with different amount of thickness reduction. Microstructural analyses have revealed that mechanical deformation by forging at lower temperatures brings about partial dissolution of cementite, which is followed by the formation of ε-carbide in the microstructures. In contrast, cementite is precipitated within ferrite matrix upon warm or hot forging at higher temperatures. It is further observed that increasing deformation percent during low-temperature forging reduces interlamellar spacing of pearlite, whereas an opposite trend is noticed in case of deformation at higher temperature; moreover, deformation induced the change in interlamellar spacing and formation of fine carbide phases in microstructures has caused appreciable enhancement in hardness of the steel.

36 MATERIALS SCIENCE↗

Effect of Si on the Formation and Growth of Intermetallic Compounds at Roll-Bonded Aluminum–Steel (Al-St) Interface

The formation and growth of intermetallic compounds (IMC) were investigated using the Al-St clad materials with additional different Si content to aluminum and steel substrate by differential scanning calorimetry, scanning electron microscopy and energy-dispersive x-ray spectroscopy, x-ray diffraction and transmission electron microscopy. The addition of Si to Al (Al-0.8Si/St) can drastically delay the formation of IMC and accelerate the growth of IMC layer. The Si (Al-0.8Si/St) segregates at the interface and inhibits the diffusion of Al atom to steel before the IMC forms, which further decreases the diffusion depth of Al in the steel layer. By contrast, the addition of Si to St (Al/St-0.8Si) has limited impact on delaying the formation and decelerating the growth of IMC layer. The Si (Al/St-0.8Si) hardly affects the diffusion of Fe atom to the aluminum layer. Among the four clad materials, the major IMC layer (η-Fe{sub 2}Al{sub 5}) always exhibits the parabolic growth phenomenon. The addition of Si cannot influence the phase compositions of IMC at the interface between the η-Fe{sub 2}Al{sub 5} layer and the aluminum. However, we observe an extra Fe-rich phase β{sub 1}-Fe{sub 3}Al at the interface between the Fe{sub 2}Al{sub 5} layer and steel substrate in the Al-0.8Si/St clad material.

36 MATERIALS SCIENCE↗