Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Performance of two-stage fan having low-aspect-ratio first-stage rotor blading

The NASA two stage fan was tested with a low aspect ratio first stage rotor having no midspan dampers. At design speed the fan achieved an adiabatic design efficiency of 0.846, and peak efficiencies for the first stage and rotor of 0.870 and 0.906, respectively. Peak efficiency occurred very close to the stall line. In an attempt to improve stall margin, the fan was retested with circumferentially grooved casing treatment and with a series of stator blade resets. Results showed no improvement in stall margin with casing treatment but increased to 8 percent with stator blade reset.

Urasek, D. C.↗

Aerodynamic performance of axial-flow fan stage operated at nine inlet guide vane angles

The overall performance of a fan stage with nine inlet guide vane angle settings is presented. These data were obtained over the stable flow range at speeds from 60 to 120 percent of design for vane setting angles from -25 to 42.5 degrees. At design speed and design inlet guide vane angle, the stage has a peak efficiency of 0.892 at a pressure ratio of 1.322 and a flow of 25.31 kg/s. The stall margin based on peak efficiency and stall was 20 percent. Based on an operating line passing through the peak efficiency point at the design setting angle, the useful operating range of the stage at design speed is limited by stall at the positive setting angles and by choke at the negative angles. At design the calculated static thrust along the operating line varied from 68 to 114 percent of that obtained at design setting angle.

Moore, R. D.↗

Transonic flow past a symmetrical airfoil at high angle of attack

The results of an experimental investigation of shock-induced stall and leading-edge stall on a 64A010 airfoil section are presented. Advanced nonintrusive techniques - laser velocimetry, holographic interferometry, and buried-wire anemometry - were used in characterizing the inviscid and viscous flow regions. The measurements include Mach contours of the inviscid flow regions, and mean velocity, flow direction and Reynolds shear stress profiles in the separated regions. The experimental observations of this study are relevant to efforts to improve surface pressure prediction methods for airfoils at or near stall.

Johnson, D. A.↗

Control considerations for CCV fighters at high angles of attack

Wind tunnel and piloted simulation studies were conducted to investigate the potential high angle of attack control problems that are introduced by the use of the CCV concept of relaxed static pitch stability (RSS) on fighter aircraft. A conventional wing/aft tail design incorporating modest levels of static instability and a close-coupled canard/wing design exhibiting very high levels of instability was investigated. Two types of high angle of attack control problems can result from the use of RSS: pitch departures caused by coupling and deep stall trim. Avoidance of these problems requires that the airplane have sufficient nose-down pitch control at high angles of attack. The effectiveness of several pitch control configurations were investigated including conventional aft-mounted stabilators, wing-mounted elevators, canard-mounted flaps, and all-moveable canards. Varying the incidence of the canards was the most effective scheme; however, very large deflections may be required on highly unstable configurations to prevent pitch departure without sacrificing roll performance and to avoid deep stall trim. For situations where the high angle of attack pitch control requirement is not met, control laws were developed to inhibit the departure and to allow deep stall recovery. However, these schemes involve limiting airplane roll capability and therefore can potentially compromise maneuverability.

Nguyen, L. T.↗

Preliminary measurements of aerodynamic damping of a transonic compressor rotor

The aeroelastic behavior of a transonic compressor rotor operated in the MIT Blowdown Compressor Facility has been examined by means of piezoelectric motion sensors at the base of each of the 23 blades. Excitation has been observed due to rotating stall, due to an incipient flutter, and due to the facility startup transient. A method has been found for determining the aerodynamic damping force by modal analysis of the blade motion. Application of this technique to the example of excitation by rotating stall has led to the conclusions that the blade loading decreases in the stall cell, and that the damping force on the blades in the clean flow is in phase with blade velocity but opposite it in sign, leading to a logarithmic decrement of 0.2. This method of force derivation has quite general applicability as it requires only blade motion data such as are routinely acquired with strain gages. It is argued that models are needed for aerodynamic damping which focus on the effects of near neighbors of a given blade, since flutter often results in large response of isolated blades or small groups of blades.

Crawley, E. F.↗

A color video display technique for flow field surveys

Color video display techniques for flow field surveys are presented. The following techniques were examined: traverse device, used for flow field surveys above and behind finite wing models; flow chart of data reduction for color video display technique; location of spanwise survey stations above and behind wing; hot wire data at first three survey stations on fully stalled wing; hot wire data at last three stations behind fully stalled wing; hot wire and pitch probe data; magnitude of velocity, yaw angle, pitch angle, and cross flow direction from 5 tube survey at X/C = 2.70 behind fully stalled wing.

Winkelmann, A. E.↗

An experimental study of separated flow on a finite wing

The flow field associated with the formation of a mushroom shaped trailing edge stall cell on a low-aspect-ratio (AR = 4.0) wing was investigated in a series of low speed wind tunnel tests (Reynolds number based on 15.2 cm chord = 480,000). Flow field surveys of the separation bubble and wake of a partially stalled and fully stalled wing were completed using a hot-wire probe, a split-film probe, and a directional sensitive pressure probe. A new color video display technique was developed to display the flow field survey data. Photographs were obtained of surface oil flow patterns and smoke flow visualization

Winkelmann, A. E.↗

Comparative study of subsynchronous rotating flow patterns in centrifugal compressors with vaneless diffusers

A comparative experimental investigation of the unstable operating modes of a centrifugal compressor was made. Impeller and/or diffuser rotating stall was observed, depending on the flow conditions. The measured relative rotational speed of this perturbation is cross checked with other experimental data and it is shown that the rotational speed is strongly dependent on the type of rotating stall. The diffuser absolute inlet flow angle at the onset of diffuser rotating stall agrees well with the value predicted by an existing stability criterion.

Frigne, P.↗

Wing modification for increased spin resistance

A simple wing leading-edge modification has been developed that delays outer wing panel stall, thus maintaining roll damping to higher angles of attack and delaying the onset of autorotation. The stall angle of attack of the outer wing panel has been shown to be a function of the spanwise length of the leading-edge modification. The margin of spin resistance provided by the modification is being explored through flight tests. Preliminary results have been used to evaluate spin resistance in terms of the difference in angle of attack between outer wing panel stall and the maximum attainable angle of attack.

Stough, H. P.↗

Wing contamination - Threat to safe flight

Attention is given to the initial results of systematic investigations of the potentially hazardous effect of heavy rain, ice, and frost accretion on aircraft wings. In the laminar region of an airfoil, roughness interferes with smooth flow and tends to encourage transition from laminar to turbulent flow upstream of its normal point of occurrence. In the airfoil's turbulent region, roughness considerably worsens the turbulent friction coefficient, thereby increasing the drag coefficient. Consequent dramatic decreases of maximum lift coefficient at high angles of attack lead to premature stall. Such decreases in stall angle destroy the safety margin of an aircraft approaching stall. An assessment is given to the state of knowledge in this field of research.

Luers, J. K.↗

Aerodynamic characteristics of two general aviation canard configurations at high angles of attack

The results of wind tunnel tests of two propeller driven canard general aviation aircraft models at high angles of attack are reported. Both tractor and pusher prop configurations were examined. Angles of attack of -6 to 40 deg were used with the pusher model at Re of 1,600,000, and from -30 to 90 deg and Re of 550,000 for the tractor model. The tests showed that the canard would stall long before the wing and produce a nose-down tendency, thus effectively keeping the aircraft out of the stall regime. However, a sequence of pilot actions or design factors such as the airfoils, relative geometry of the canard and wing, the propeller location and the center of gravity location could introduce a wide variance in stall characteristics from one aircraft to another.

Chambers, J. R.↗

Test and evaluation of the HIDEC engine uptrim algorithm

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrated engine-airframe control systems. Performance improvements will result from an adaptive engine stall margin mode, a highly integrated mode that uses the airplane flight conditions and the resulting inlet distortion to continuously compute engine stall margin. When there is excessive stall margin, the engine is uptrimmed for more thrust by increasing engine pressure ratio (EPR). The EPR uptrim logic has been evaluated and implemented into computer simulations. Thrust improvements over 10 percent are predicted for subsonic flight conditions. The EPR uptrim was successfully demonstrated during engine ground tests. Test results verify model predictions at the conditions tested.

Ray, R. J.↗

Aspects of the 40-50 day oscillation during the northern winter as inferred from outgoing longwave radiation

One-point correlation statistics and extended empirical orthogonal function analysis are used to show the existence of a principal mode of oscillation in the intraseasonal variability (ISV) of tropical convection. The data analyzed were derived from NOAA Outgoing Longwave Radiation data covering seven 6 mo periods from 1974-83. The data is filtered to remove fluctuations on time scales under 5 days and by subtracting a least-squares parabola to eliminate seasonal means. The previously-known 40-50 day oscillation is found to be the most prevalent component of the ISV of tropical convection. An E-W dipole forms and propagates over the equatorial Indian Ocean, then stalls and intensifies over Indonesia and the equatorial Indian Ocean, then stalls and intensifies over Indonesia and the equatorial central Pacific. Various anomalies generated in association with the dipole and dependent on its exact location when stalled are discussed.

Lau, K.-M.↗

Test and evaluation of the HIDEC engine uptrim algorithm

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrated engine-airframe control systems. Performance improvements will result from an adaptive engine stall margin mode, a highly integrated mode that uses the airplane flight conditions and the resulting inlet distortion to continuously compute engine stall margin. When there is excessive stall margin, the engine is uptrimmed for more thrust by increasing engine pressure ratio (EPR). The EPR uptrim logic has been evaluated and implemente into computer simulations. Thrust improvements over 10 percent are predicted for subsonic flight conditions. The EPR uptrim was successfully demonstrated during engine ground tests. Test results verify model predictions at the conditions tested.

Ray, R. J.↗

Separation control over an airfoil at high angles of attack by sound emanating from the surface

Active control by sound emanating from a narrow gap in the vicinity of the leading edge of a symmetrical airfoil is used to study the influence of sound on the pressure distribution and the wake at high angles of attack. The results from experiments conducted at a Reynolds number based on the chord of 35,000 show that, with injection of sound at twice the shedding frequency of the shear layer, the region of separation becomes drastically reduced. The shear layer is found to be very sensitive to sound excitation in the vicinity of the separation point. The excitation sufficiently alters the global circulation to cause an increase in lift and reduction in drag. Furthermore, experimental results describing stall and post-stall conditions compare well with the limited data available and indicate that stall is delayed by sound injection into the separated region.

Huang, L. S.↗

Analysis and test evaluation of the dynamic stability of three advanced turboprop models at zero forward speed

Results of static stability wind tunnel tests of three 62.2 cm (24.5 in) diameter models of the Prop-Fan are presented. Measurements of blade stresses were made with the Prop-Fans mounted on an isolated nacelle in an open 5.5 m (18 ft) wind tunnel test section with no tunnel flow. The tests were conducted in the United Technology Research Center Large Subsonic Wind Tunnel. Stall flutter was determined by regions of high stress, which were compared with predictions of boundaries of zero total viscous damping. The structural analysis used beam methods for the model with straight blades and finite element methods for the models with swept blades. Increasing blade sweep tends to suppress stall flutter. Comparisons with similar test data acquired at NASA/Lewis are good. Correlations between measured and predicted critical speeds for all the models are good. The trend of increased stability with increased blade sweep is well predicted. Calculated flutter boundaries generaly coincide with tested boundaries. Stall flutter is predicted to occur in the third (torsion) mode. The straight blade test shows third mode response, while the swept blades respond in other modes.

Smith, Arthur F.↗

Effect of spatial inlet temperature and pressure distortion on turbofan engine stability

The effects of circumferential and radial inlet temperature distortion, circumferential pressure distortion, and combined temperature and pressure distortion on the stability of an advanced turbofan engine were investigated experimentally at simulated altitude conditions. With circumferential and radial inlet temperature distortion, a flow instability generated by the fan operating near stall caused the high-pressure compressor to surge at, or near, the same time as the fan. The effect of combined distortion was dependent on the relative location of the high-temperature and low-pressure regions; high-pressure compressor stalls occurred when the regions coincided, and fan stalls occurred with the regions separated.

Mehalic, Charles M.↗

Numerical study of delta wing leading edge blowing

Spanwise and tangential leading edge blowing as a means of controlling the position and strength of the leading edge vortices are studied by numerical solution of the three-dimensional Navier-Stokes equations. The leading edge jet is simulated by defining a permeable boundary, corresponding to the jet slot, where suitable boundary conditions are implemented. Numerical results are shown to compare favorably with experimental measurements. It is found that the use of spanwise leading edge blowing at moderate angle of attack magnifies the size and strength of the leading edge vortices, and moves the vortex cores outboard and upward. The increase in lift primarily comes from the greater nonlinear vortex lift. However, spanwise blowing causes earlier vortex breakdown, thus decreasing the stall angle. The effects of tangential blowing at low to moderate angles of attack tend to reduce the pressure peaks associated with leading edge vortices and to increase the suction peak around the leading edge, so that the integrated value of the surface pressure remains about the same. Tangential leading edge blowing in post-stall conditions is shown to re-establish vortical flow and delay vortex bursting, thus increasing C sub L sub max and stall angle.

Yeh, David↗